LG LST-270T User Manual

LST-270T USER GUIDE

Please read this manual carefully before operating your set. Retain it for future reference.

TEBLE OF CONTENTS

1.1 Safety Instruction

WARNING/CAUTION

To reduce the risk of fire or electric shock, do not expose this product to rain or moisture. Do not use this product near swimming pools or other water bodies.

IMPORTANT

Before installing or operating this product read this information.

1.2 Optimal Phone Performance

▶

Do not operate your product when holding the antenna, or when someone is within four inches (ten centimeters) of the antenna. Holding the antenna affects call quality and may cause the telephone to operate at a higher power level than needed.

▶

For the best call quality, keep the antenna free from obstructions and position the antenna straight up.

▶

Do not use the phone with a damaged antenna. Have your antenna replaced by a qualified technician immediately. Use only the Authorized LGE Service Center-approved antenna. Non-

approved antennas, modifications, or attachments could impair call quality, damage the phone.

▶

RF energy may affect improperly installed or inadequately shielded personal medical devices such as pace makers, hospital monitor. Consult the manufacturer of any personal medical devices to determine if they are adequately shielded from external RF energy. Turn your terminal OFF in health care facilities when any regulations posted in the areas instruct you to do so.

Hospitals or health care facilities may be using equipment that could be sensitive to external RF energy.

▶

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the distance between the radio or television and the telephone.

- Connect the equipment into an outlet on a circuit different from that to which the terminal is connected.

- Consult your experienced radio/TV technician of

Before You Start 3

1.1 Safety Instruction 3

1.2 Optimal Phone Performance 3

1.3 Care and Service 4

1.4 Safety Information 5

Introduction 8

2.1 Component List 9

2.2 Front, Side and Rear View of the Terminal 10

2.3 3 LEDs Indicators 12

2.4 Installation 13

2.5 Installation Steps 16

Basic Operation 17

3.1 Power On 17

3.2 Placing a Call 17

3.3 Receiving a Call 18

3.4 Ending a Call 18

3.5 Warning Tone after Remote Disconnect 18

3.6 Emergency Call 18

3.7 Power Off 18

System Features 19

4.1 Hook Flash 19

4.2 ROH (Receiver Off Hook) 19

4.3 System Features 19

4.4 Applications 20

Programming 21

5.1 Speed Dial 21

5.2 Emergency Call 22

5.3 Hot Line 23

5.4 Alarm 24

5.5 Volume Level 25

5.6 Outgoing Call Lock 26

5.7 Restrict Call Mode Setting 26

Troubleshooting 29 General Information 30 Limited warranty statement 32 FCC RF Exposure Information 35 LGE Service Center List 36

Before You Start

Before You StartTable of Contents

Before You Start

1.4 Safety Information

WWAARRNNII NN GG

▶

Do not use harsh chemicals, cleaning solvents, or strong detergents to clean it. Wipe it with a soft cloth that has been slightly dampened in a mild soapand water solution.

▶

Do not paint it. Paint can clog the device’s moving parts and prevent proper operation.

▶

During lightning, do not touch power plug or phone line. It may cause an electric shock or death.

CC AAUU TTIIOONN

▶

Do not use with car battery. It may cause an electric shock, fire, breakdown or transformation.

▶

For safety use, use only adapter approved by LG.

To all problems arising from not following this guide, LG does not bear responsibility.

▶

Avoid exposure to high temperature or humidity.

Avoid wetting the unit with any liquids. If the unit gets wet, turn the power off immediately and remove the backup battery and AC power supply.

▶

Keep it dry. Precipitation, humidity, and liquids contain minerals that may corrode electronic circuits.

▶

Do not use or store it in dusty, dirty areas as its moving parts can be damaged.

▶

Do not store it in hot areas. High temperatures can shorten the life of electronic devices, damage batteries, and warp or melt certain plastics.

the Authorized LGE Service Center

▶

Use only the battery, antenna and AC power supply provided by LGE.

Using any other type will invalidate the warranty.

▶

Only authorized personnel should service the phone and its accessories.

Faulty installation or service can be dangerous and may invalidate the warranty.

▶

Do not use the phone in designated “no cellular phone use” area.

Avoid exposure to high temperature or humidity.

▶

Avoid wetting the phone with any liquids. If the phone gets wet, turn the power off immediately and remove the backup battery and AC power supply.

If the phone is inoperable, then return to the service agent for service.

▶

Avoid shock or impact.

▶

We recommend you to charge the backup battery before initial use. Backup battery may be discharged during delivery.

▶

This phone complies with part 15 of the FCC Rules.

Operation is subject to the following two conditions:

- This phone may not cause harmful interference, and

- This phone must accept any interference received, including interference that may cause undesired operation.

1.3 Care and Service

▶

Unplug the telephone from the wall outlet and remove antenna (or disconnect antenna cable) before cleaning. Do not use liquid or aerosol cleaners. Use a damp cloth for cleaning.

▶

If the phone fails for any reason, do not attempt to disassemble; contact the Authorized LGE Service Center for assistance.

▶

If any of the following conditions exist: unplug the phone at the wall plug, remove battery, and call the service provider.

- The power supply cord is damaged or frayed.

- Liquid has been spilled into the phone.

- The phone has been exposed to rain or water.

- The phone has been dropped or damaged.

- The phone does not work normally by following

the operating instructions.

Before You Start

▶

Do not short-circuit. It may start a fire or may explode causing injury.

▶

Do not throw and impact battery. Do not dispose of batteries by putting them in fire. It may explode or catch fire by electrolyte.

▶

When you disconnect the power cord of any accessory, grasp and pull the plug, not the cord. It may cause an adapter breakdown.

Before You Start

▶

Do not store it in cold areas. When the phone warms up to its normal operating temperature, moisture can form inside the phone, which could damage the phone’s electronic circuit boards.

▶

Do not attempt to open it. Nonexpert handling of the device could damage it. Consult your authorized LGE Service Center for help. It may be a cause of fire, electric shock and breakdown.

▶

Do not drop, knock or shake it. Rough handling can break internal circuit boards.

▶

Do not install under direct sunlight or on an uneven surface.

▶

Before using plug, check with available power voltage.

Inaccurate power voltage may be a cause of fire.

▶

Do not plug many power cords in outlet. It may be a cause of fire or electric shock.

▶

Do not remodel the power cord or disassemble. If power cord or plug is impaired, do not use it. It may be a cause of fire or electric shock.

▶

Do not install in an ill-ventilated place. It may be a cause of fire or breakdown.

▶

Do not touch the plug with wet hands. When disconnecting the power cord of any accessory, grasp and pull the plug, not the cord. It may be a cause of fire or electric shock.

▶

Do not put heavy things on the power cord. Do not bend power cord too much. It may be a cause of fire or electric shock.

Introduction

Congratulations on your purchase of the LG Fixed Wireless Terminal that has been designed to operate on the latest digital mobile communications technology,

Code Division Multiple Access (CDMA). This CDMA digital technology has greatly enhanced voice clarity and can provide various advanced features.

The terminal enables the normal operation and direct connection of standard telephone equipment into the cellular network.

The standard unit provides:

▶

A phone jack to plug in the telephone equipment(RJ-11 Port)

▶

Ring voltage used to ring the telephone connected to the unit, with a Ringer Equivalence Number of 4

▶

Data Port for repair(RJ-45 Port)

▶

AC Power supply with barrel plug connector

▶

Support Dial tone

▶

Touch tone(DTMF) or Pulse Dialing

▶

Support Caller ID Telephone(DTMF only, not Support FSK)

▶

Voice-Mail Notification ring alerts you to new voice-mail messages

▶

Three lights (LEDs) to indicate the status of the unit

▶

Dipole Antenna

Some features can not be supported by service provider’s equipment status.

For instance, the following features may not be supported:

▶

Speed Dial

▶

Emergency Call

▶

Hot Line Call

▶

Alarm

▶

Outgoing Call Lock

▶

Quick Dial Option with “J”

Other features as determined by your service provider.

Note:

- Telephones with multiple terminating impedance should be set for 600ohms.

Introduction

2.1 Component List

WIRELESS LOCAL LOOP

< AC/DC Power Adapter >

< Terminal >

< Backup Battery(Built-in) >

< User Guide >

< Dipole Antenna >

Introduction

Installation for Wall Mounting

▶

To mount terminal on the wall, please follow the procedure to install it correctly.

1. Determine suitable location to mount terminal with mounting template.

2. Mark the two openings and select round or panhead type screw.

3. Drill out the holes with drill bit smaller in diameter than the screws.

4. Secure two screws into the wall, leaving about 65mm gap between the screw heads.

5. Insert the DC power jack into an electrical outlet and attach the telephone line into the Phone Jack (RJ-11) of the terminal.

6. Place the terminal over the two screws.

7. Slide the terminal downward until the screw head is locked at the top of the opening and the terminal is secure.

8. Check that set is fixed on the screws.

Introduction

2.2 Front, Side and Rear View of the Terminal

WIRELESS LOCAL LOOP

< Figure 1 >

< Mounting Template >

IITTEEMM DDEE SSCC RRII PPTTIIOONN (1) LEDs Indicate the status of the unit (2) DC IN 12V AC/DC Power Adapter (3) Battery Switch Battery On/Off Switch (4) TEL (RJ-11 Port) Connecting Ports for SLT

(Single Line Telephone) (5) DATA Port (RJ-45 Port) Connecting Port for Repair(RS-232C) (6) Antenna Connector Connecting Port for TNC Antenna (7) Power Power On/Off Key

1312

2.4 Installation

You should follow each step carefully as shown below in order to guarantee proper operation of CDMA Fixed Wireless Telephone.

STEP I. Check Components

▶

Fixed Wireless Terminal is supplied with the following standard unit and accessories:

1. LST-270T Unit -1EA-

2. Dipole Antenna -1EA-

3. Backup Battery -1EA-

4. User Guide -1EA-

5. AC/DC Power Adapter -1EA-

▶

Please make sure that these components are present and check for evidence of shipping before you begin the unit installation.

▶

If components are missing or damage is found, contact your authorized LGE Service Center immediately.

STEP II. Place the Terminal

▶

Place the terminal on the stable flat secure surface area (desk, table, etc.).

Avoid direct exposure to the sunlight and damp areas.

▶

Read the SAFETY INFORMATION located at the first part of this document before you place the terminal.

STEP III. Connect Components

▶

Connect the Dipole antenna to the TNC connector located at the topside of the terminal. (See Figure 1 to locate the TNC connector.)

If you have placed the terminal on the flat surface, position the antenna up side.

▶

Connect your phone cord to the RJ-11 port located at the side of the terminal.

▶

Connect the battery cable to the DC battery connector at the side of the terminal.

- Remove the battery compartment cover.

Introduction

2.3 3 LEDs Indicators

< Table 1 >

Introduction

LL EEDD CCOOLL OORR OOpp ee rraa ttiinngg CCoo nndd ii ttiioo nn

GREEN-solid Good Signal

SIGNAL LED ORANGE-solid Poor Signal

RED-solid No Service Area

MODE LED

GREEN - blink Voice Message is received

(0.5sec On / 0.5sec Off)

GREEN-solid DC Power is applied

POWER LED RED-solid Battery Power is applied

ORANGE-solid Low Battery

- Connect battery to the connector.

- Replace the battery cover.

▶

Connect the AC power supply cable to the DC input port located at the side of the terminal.

““RReeffeerr ttoo ccoo nnnneecctt ii oonn DDiiaaggrraamm wwiitt hh eexxtteerrnnaall eeqq uuiipp mmeenntt iinn FFii gguurr ee 22””

STEP IV. Check LED Indicators

▶

When you followed the installation instruction STEP I to STEP III, please check the LEDs for normal operation.

▶

When DC power is fed at the first time, LEDs will operate as follows:

After few seconds, Power LED is GREEN, if AC/DC power is applied.

If receiving signal strength is strong enough, then SIGNAL LED is GREEN.

If not, it is ORANGE or RED. And MODE LED is turned off.

Introduction

< Figure2. Connection Diagram with External Equipment >

LST-270T

Note:

- Length between LST-270T and Telephone : over 1m.

.. TThh ee aaddaa pptteerr ttyypp ee ((wwiitt hh ppooww ee rr ccoorrdd)) mmaayy bbee ddiiff ffeerr ee nntt ffrr oomm ccoouunn ttrr yy ttoo ccoouunn ttrr yy ..

! Connection telephone jack to data port will cause malfunction of data service

Before using the terminal, please check battery switch is on. After switching on it, use the phone. When charging the battery, check that battery switch is “on”.

Notice

Battery Switch

+ 17 hidden pages