LG LND3220R User Guide

Specication

OWNER’S MANUAL

Network Camera

Please read this manual carefully before operating your set and retain it for future reference.

To view the instructions of advanced features, visit http://www.lgecommercial.com and then download Owner’s Manual / Software.

MODEL LND3220R

Camera

Video

Event

Item LND3220R

Image Device 6.4 mm (1/2.8 Type) CMOS

Lens Type 4 mm F2.0

Day/Night ICR (Auto / Day / Night)

Minimum Illumination

IR Distance 20 m

WDR Digital (Dynamic Range Enhancer)

Image Enhancement

Compression H.264_HIGH, H.264, MJPEG

Resolution 1920 x 1080 / 1280 x 720 / D1 (704 x 480) / CIF (352 x 240)

Maximum Frame Rate

Multi-Streaming Up to 7

ROI (Region of Interest)

Video Analytics Motion detection, Tampering alarm

Event Notication

Pre Event Buering

Color: 0.07 lx @ F2.0 (1/30 sec, 50 IRE)

B/W: 0 lx @ IR LED on

Backlight Compensation, DNR, Exposure Control, AGC, White Balance, Privacy Masking, Sharpness

30 fps @ 1920 x 1080

Up to 4

Email, FTP

Support

Ethernet RJ-45 10 / 100 BASE-T

Security Password Protection, HTTPS(SSL, TLS), IP ltering, IEEE 802.1X

Open Protocol ONVIF 2.2 Prole S, PSIA 1.1

Network

General

Note that design and specication of this unit may change from the manual as quality and improvement without prior notice.

Components

Camera, Installation Manual, Tapping Screw (4 EA), Installation sticker, Camera mounting bracket

Protocol

Connections Up to 10

Integrated Software

Power Source DC 12 V, PoE

Maximum Power Consumption

Maximum Input Current

Operation Temperature/ Humidity

Dimension (Ø x H)

Weight 479 g

IPv4 and IPv6: TCP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP, QoS, UPnP

IPv4: FTP, SMTP, NTP, ARP, SNMPv1/v2c/v3, DDNS(LG)

LG Ipsolute VMS Suite / Mobile application (iPhone, iPad, Android)

5.4W (DC 12 V), 5.9 W (PoE 48 V)

450 mA (DC 12 V), 140 mA (PoE 48 V)

-10 ºC to 55 ºC / 0 % RH to 80 % RH

140 mm x 122 mm

OPEN SOURCE SOFTWARE NOTICE

To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This oer is valid for three (3) years from the date on which you purchased the product.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user.

• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.

This Class A digital apparatus complies with Canadian ICES-003.

Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

Warning: Please adopt the power adapter which can meet the safety extra low voltage (SELV) standard. And source with DC 12 V or AC 24 V (depending on models) according to the IEC60950-1 and Limited Power Source standard.

Warning: Install the camera on a ceiling or wall where can withstand the weight of 5 times of the camera including mounting bracket.

Caution: This installation shall be made by a qualified service person and shall conform to all local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only.

Caution: The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus.

Caution: Make sure the power supply voltage is correct before using the camera.

Caution: Do not drop the camera or subject it to physical shock.

Caution: The sensor may be burned out by a laser beam, so when any laser equipment is being used, make sure that the surface of the sensor not be exposed to the laser beam.

Caution: While shipping, the camera should be packed in its original packing.

The Power Plug is the disconnecting device. In case of an emergency, the Power Plug must remain readily accessible.

Contact oce for compliance of this product:

LG Electronics European Shared Service Center B.V.

European Standard Team

Krijgsman 1

1186 DM Amstelveen

The Netherlands

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10. Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms or when unused for long periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as power-supply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Handling of the unit

Be careful not to spill water or other liquids on the unit. Be cautious not to get combustible or metallic material inside the body. If used with foreign matter inside, the camera is liable to fail or to get cause of fire or electric shock.

• Remove dust or dirt on the surface of the lens with a blower.

• Use a soft and lint-free, dry cloth(such as glass cleaner) to clean the body. If it is very dirty, use a cloth dampened with a small quantity of neutral detergent then wipe dry.

• Avoid the use of volatile solvents such as thinners, alcohol, benzene and insecticides. They may damage the surface finish and/ or impair the operation of the camera.

• This camera is designed for mounting on the ceiling or wall. If you install this camera upside down, it may cause malfunction.

Operating and storage location

Avoid viewing a very bright object (such as light fittings) during an extended period. Avoid operating or storing the unit in the following locations.

• Extremely hot or cold places (operating temperature -10 °C to 55 °C, however, we recommend that the unit be used within a temperature range of 0 °C to 45 °C)

• Damp or dust place

• Places exposed to rain

• Places subject to strong vibration

• Close to generators of powerful

electromagnetic radiation such as radio or TV transmitters.

• Do not use the camera in such place where rapid temperature fluctuation by switching an air conditioner on and off.

Part Names and Functions

Connection

b c

a Dome Cover

b IR LED

Do not stare at operating IR LED within hazard distances (1 m).

c IR Sensor

d Camera mounting bracket

You can lock the camera mounting bracket by tighten the screws.

To disassemble the camera from the mounting bracket, rotate the camera

counterclockwise with pressing the PUSH button inside the camera body.

e Power input terminal

Connects to a DC 12 V power supply using proper cables. This camera must always be operated a DC 12 V. Certied/Listed Adaptor which comply with LPS.

f ETHERNET / PoE Port

Connects to a PC or a network via a hub with a 10 BASE-T / 100 BASE-TX cable attached RJ-45 connector.

Power over Ethernet (PoE) is a technology that integrates power into a standard LAN

infrastructure. It enables power to be provided to the network device, such as a network camera, using the same cable as that used for network connection. It eliminates the need for power outlets at the device locations and enables easier application of uninterruptible power supplies (LPS).

g RESET button

Push the button more than 3 seconds, this would restore the factory default network related settings.

Precautions

• Be sure to switch o the unit before installation and connection.

• The installation should be made by qualied service personnel or system installers.

• Do not expose the power and connection cables to moisture, which may cause damage to the unit.

Connecting Network

You can control and monitor the system via network. With the remote control (monitoring), you can change the system conguration or monitor the image via network. After the installation, check the network settings for the remote control and monitoring work. Connect the IP camera to your network using a standard RJ-45 network cable as shown below.

PoE device

(IEEE802.3af )

Broadband

Service

Router

Connecting Power Source

Connect power, using one of the methods listed below:

To use the power adapter

Connect a DC 12 V power source to the power input terminal as shown below. (Recommended power adapter is DC 12 V / 1.5 A or above)

• When the connecting power adapter, tighten the

screws as shown above.

• Put your nger between the power connector and the camera body to pull out the connector.

To use the PoE (Power over Ethernet) device

Connect the PoE cable to the LAN port on the unit. You must use the “IEEE802.3af” standard PoE device.

PoE device

(IEEE802.3af )

If the camera doesn’t work properly after connecting

PoE device, please check if the PoE device supplies enough power.

e f g

Installation

Mounting the camera

Follow the instructions below to surface mount the camera with supplied camera mounting bracket.

1. Use the installation guide template to check the mounting location. Face the front of the label toward the area of interest. Using the template as a guide, make a hole through the ceiling.

2. Disassemble the camera from the mounting bracket. Install the camera mounting bracket to the ceiling.

Broadband

Service

3. Connect the cables to the cable jacks of the camera body. 4. Assemble the camera and mounting bracket after align the front part of the camera and

mounting bracket. Connect the unit by following step a and b.

• Be careful of sharp edge after removing the cap of cable conduit.

Camera Adjustment

Adjust the Pan/Tilt/Rotation position of the camera.

ROTATION

PAN 270°

• When you assemble the dome cover, make sure the arrow of base bracket position is

aligned with the LG logo.

• Manual adjustment: PAN: 360° / TILT: 75° / ROTATION: 355°

• When you adjust PAN/TILT/ROTATION manually, be careful your hand is not to hurt by

protrusions of other part.

• When you adjust PAN/TILT/ROTATION manually, be careful the cable is not damaged or pinched.

TILT

PAN 90°

• Arrange the cables by cable tie after installation.