LG LND3100 User guide

OWNER'S MANUAL

High Definition Network Dome
Camera

Please read this manual carefully before operating
your set and retain it for future reference.

MODEL

LND3100 series

AB28

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is
intended to alert the user to the presence of uninsulated dangerous voltage
within the product’s enclosure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the
user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or
modifications to this equipment may cause harmful interference unless the modifications are
expressly approved in the instruction manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device,
pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed
and used in accordance with the instruction manual, may cause harmful interference to radio
communications.
Operation of this equipment in a residential area is likely to cause harmful interference in which
case the user will be required to correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this
product in the end user.

• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or
equivalent type recommended by the manufacturer. Dispose of used batteries according to
the manufacturer’s instructions.

• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces
or shall be provided with brushings.

This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Warning: Do not install this equipment in a
confined space such as a bookcase or similar
unit.

Warning: Wiring methods shall be in
accordance with the National Electric Code,
ANSI/NFPA 70.

Warning: This is a class A product. In a
domestic environment this product may cause
radio interference in which case the user may
be required to take adequate measures.

Warning: To reduce a risk of fire or electric
shock, do not expose this product to rain or
moisture.

Caution: This installation shall be made by a
qualified service person and shall conform to
all local codes.

Caution: To avoid electrical shock, do not
open the cabinet. Refer servicing to qualified
personnel only.

Caution: The apparatus shall not be exposed
to water (dripping or splashing) and no objects
filled with liquids, such as vases, shall be
placed on the apparatus.

To disconnect power from mains, pull
out the mains cord plug. When installing
the product, ensure that the plug is easily
accessible.

LG Electronics hereby declares
that this/these product(s) is/are
in compliance with the essential
requirements and other relevant
provisions of Directive 2004/108/
EC and 2011/65/EU.

Contact office for compliance
of this product :

LG Electronics Inc.
EU Representative, Krijgsman 1,
1186 DM Amstelveen, The
Netherlands

Disposal of your old appliance

1. When this crossed-out
wheeled bin symbol is
attached to a product
it means the product is
covered by the European
Directive 2002/96/EC.

2. All electrical and electronic
products should be
disposed of separately from
the municipal waste stream
via designated collection
facilities appointed by the
government or the local
authorities.

3. The correct disposal of
your old appliance will help
prevent potential negative
consequences for the
environment and human
health.

4. For more detailed
information about disposal
of your old appliance,
please contact your city
office, waste disposal
service or the shop
where you purchased the
product.

EEE Compliance with Directive.
(for Turkey only)

Important Safety
Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings.
Install in accordance with the
manufacturer’s instructions.

8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including amplifiers) that
produce heat.

9. Do not defeat the safety purpose of
the polarized or grounding-type plug.
A polarized plug has two blades with
one wider than the other. A grounding
type plug has two blades and a third
grounding prong. The wide blade or the
third prong are provided for your safety.
If the provided plug does not fit into
your outlet, consult an electrician for
replacement of the obsolete outlet.

10. Protect the power cord from being
walked on or pinched particularly at
plugs, convenience receptacles, and the
point where they exit from the apparatus.

11. Only use attachments/accessories
specified by the manufacturer.

12. Use only with the cart, stand, tripod,
bracket, or table specified by the
manufacturer, or sold with the apparatus.
When a cart is used, use caution when
moving the cart/apparatus combination
to avoid injury from tip-over.

13. Unplug this apparatus during lightning
storms or when unused for long periods
of time.

14. Refer all servicing to qualified service
personnel. Servicing is required when
the apparatus has been damaged in any
way, such as power-supply cord or plug
is damaged, liquid has been spilled or
objects have fallen into the apparatus, the
apparatus has been exposed to rain or
moisture, does not operate normally, or
has been dropped.

Handling of the unit

Be careful not to spill water or other liquids on
the unit. Be cautious not to get combustible or
metallic material inside the body. If used with
foreign matter inside, the camera is liable to
fail or to get cause of fire or electric shock.

• Remove dust or dirt on the surface of the
lens with a blower.

• Use a dry soft cloth to clean the body. If it
is very dirty, use a cloth dampened with a
small quantity of neutral detergent then
wipe dry.

• Avoid the use of volatile solvents such
as thinners, alcohol, benzene and
insecticides.
They may damage the surface finish and/
or impair the operation of the camera.

• This camera is designed for mounting
on the ceiling or wall. If you install this
camera upside down, it may cause
malfunction.

Operating and storage
location

Avoid viewing a very bright object (such as
light fittings) during an extended period. Avoid
operating or storing the unit in the following
locations.

• Extremely hot or cold places (operating
temperature -10 °C to 50 °C, however, we
recommend that the unit be used within
a temperature range of 0 °C to 45 °C)

• Damp or dust place

• Places exposed to rain

• Places subject to strong vibration

• Close to generators of powerful

electromagnetic radiation such as radio
or TV transmitters.

• Do not use the camera in such place
where rapid temperature fluctuation by
switching an air conditioner on and off.

Specification

Item LND3100 series

Image Device 6.08 mm (1/3 type) Progressive Scan CMOS (1.3 Mega

Pixels)

Lens Type 3 mm F2.0

Day/Night Digital

Minimum Illumination 0.7 lx (F1.2, Sens-up off )

0.05 lx (F1.2, Sens-up x60)

WDR Support

Image Enhancement Backlight Compensation, 2D+3D-DNR, Exposure

Control, Sens Up Control, AGC, White Balance, Privacy
Masking, EIS, Sharpness, Digital Zoom

Video Analytics Motion detection

Resolution (Maximum) Up to 1 280 x 1 024

Output RJ-45 (Network), RCA (Installation)

Frame Rate (Maximum) 30 fps @ 1 280 x 1 024, 30 fps @ 720p

Compression H.264_HIGH, H.264, MJPEG

Multi-Streaming Dynamic Profile (Up to 7)

ROI (Region of Interest) Support

SD Slot Micro SD

EVENT Event Notification Email, FTP

Pre Event Buffering Support

Integrated Client LVi510

Remote S/W LVi510, Mobile application (iPhone, Android, iPad)

Connections Up to 10

Security Password Protection, HTTPS(SSL, TLS), IEEE 802.1X

Ethernet 10/100 Ethernet

IPv4 and IPv6 TCP/IP, UDP, HTTP, HTTPS, RTP, RTSP, DHCP, ICMP

Protocol

IPv4 FTP, SMTP, NTP, ARP, SNMP v1/v2c/v3, DDNS(LG)

Open Protocol ONVIF 2.2 Profile S, PSIA 1.1

Operation Temperature/Humidity -10 ºC to 50 ºC / 0 % RH to 80 % RH

Power Source PoE, DC 12 V

Power Consumption 5.9 W

Input current Maximum 440 mA (DC 12 V), Maximum 140 mA (PoE)

Dimension (Ø x H) 140 mm x 110 mm

Weight 506 g

Part Names and Functions

a

b
c
d
e
f

g

h
i

a Dome Cover

b Azimuth adjuster

c Lens Cover

d RESET button

Push the button more than 3 seconds, this would restore the factory default network

related settings.

e micro SD card slot

Insert the micro SD card.

f Pan adjuster

Adjusts the pan position.

g ETHERNET/PoE Port

Connects to a PC or a network via a hub with a 10 BASE-T/100 BASE-TX cable attached

RJ-45 connector.

NOTE:

Power over Ethernet (PoE) is a technology that integrates power into a standard LAN
infrastructure. It enables power to be provided to the network device, such as a network
camera, using the same cable as that used for network connection. It eliminates the need
for power outlets at the device locations and enables easier application of uninterruptible
power supplies (LPS).

h Power input terminal

Connects to a DC 12 V power supply using proper cables. This camera must always be
operated a DC 12 V. Certified/Listed Adaptor which comply with LPS.

i Camera mounting bracket

ETHERNET
With PoE

Connection

FRONT

PRODUCT CENTER POSITION

MEZ62687703

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

PRODUCT CENTER POSITION

MEZ62687703

4 Place

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

Precautions

• Be sure to switch off the unit before installation and connection.

• The installation should be made by qualified service personnel or system installers.

• Do not expose the power and connection cables to moisture, which may cause damage to

the unit.

Connecting Network

You can control and monitor the system via network. With the remote control (monitoring), you
can change the system configuration or monitor the image via network. After the installation,
check the network settings for the remote control and monitoring work.
Connect the IP camera to your network using a standard RJ-45 network cable as shown below.

ETHERNET
With PoE

PoE Device

(IEEE802.3af )

Broadband

Service

Connecting Power Source

Connect power, using one of the methods listed below:

To use the power adapter

Connect a DC 12 V power source to the power input terminal as shown below.
(recommended power adapter is DC 12 V/1.5 A or above)

POWER IN
DC 12 V

To use the PoE (Power over Ethernet) device

Connect the PoE cable to the LAN port on the unit. You must use the “IEEE802.3af” standard PoE
device.

ETHERNET
With PoE

PoE Device

(IEEE802.3af )

Using the micro SD card

You can record your surveillance environment with the micro SD card even if the network is
disconnected condition.

To insert the micro SD card

1. Remove the Dome Cover.

2. Insert the micro SD card carefully as shown in the following illustrations. Make sure the micro
SD card terminal position before insert the micro SD card. Push the back end of the micro
SD card to fix it at the last step.

NOTES:

• Do not use the power too much when you insert the micro SD card. The micro SD card may
be damaged.

• If you insert the micro SD card in the wrong position, the micro SD card may be damaged or
it may cause the malfunction of the micro SD Card Slot.

• Keep the terminal part of the micro SD card in clean. Be careful the terminal part of the
micro SD card not to dusty.

• As the micro SD card is consumable, the micro SD card end its days and may be not able to
save data if you use it more than over certain times. In this case, replace micro SD card to
buy a new one.

Remove the micro SD card

1. Press the back end of the micro SD card to release the lock condition.

2. Take the micro SD card out carefully from the camera. It may cause a malfunction of the
micro SD card or the micro SD card slot if you use the power too much at lock status.

CAUTION:

• If you install the micro SD card on the camera and remove with the micro SD card condition
indicator lights on, you must unmount the micro SD card by using the [System > Storage
> Device Management > Unmount] menu. The micro SD card data is compromised or the
camera may not operate normally, if you remove the card without use [Unmount] function.

• LG Electronics is not responsible for deleted data caused by user mishandling when you
insert or remove the micro SD card.

Recommended the micro SD card specification

Maker Capacity

LG

Sandisk

Transcend

Less than

32 GB

Block Size

(FAT 32)

32 kbyte

NOTE:

Speed of reading and writing more than 10 MB/Sec. (Class 6)

Router

Broadband

Service

Mounting the camera

Follow the instructions below to surface mount the camera with supplied camera mounting
bracket.

1. Use the installation guide template to check the mounting location. Face the front of the
label toward the area of interest. Using the template as a guide, make a hole through the
ceiling.

FRONT

4 Place

SELFTAPPING SCREW

MEZ62687703

PRODUCT CENTER POSITION

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

CAUTION:

Install on a ceiling or wall where can withstand the weight of 5 times of the camera including
mounting bracket.

2. Pass the connection cable through the inner side of the ceiling.

FRONT

MEZ62687703

PRODUCT CENTER POSITION

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

4 Place

CABLE HOLE (LCD5300)

NOTE:

supplies enough power.

If the camera doesn’t work properly after connecting PoE device, please check if the PoE device

3. Install the camera mounting bracket to the ceiling.

4. Connect the cables to the cable jacks of the camera body.

5. Assemble the camera and mounting bracket after align the front part of the camera and

mounting bracket. Connect the unit by following step a and b.

FRONT

4 Place

SELFTAPPING SCREW

MEZ62687703

PRODUCT CENTER POSITION

CABLE HOLE (LCV5300)

CABLE HOLE (LCD5300)

FRONT

MEZ62687703

PRODUCT CENTER POSITION

SELFTAPPING SCREW

CABLE HOLE (LCV5300)

4 Place

CABLE HOLE (LCD5300)

NOTE:

To disassemble the camera from the mounting bracket, rotate the camera counterclockwise with
pressing the PUSH button inside the camera body.