Life's Good
FRE CH DOOR
REFRIGERATOR
Please read 1his owners manuaO thoroughly before
operating and keep if handy for reference at al8 times.
LMXS27626 -_
P/No,: MFL68680402
2 TABLEOFCONTENTS
TABLE OF CONTENTS
3 PRODUCT FEATURES
4 IMPORTANT SAFETY
INSTRUCTIONS
7 COMPONENTS
7 Refrigerator Exterior
8 Refrigerator Interior
9
INSTALLATION
9 Installation Overview
10 Specifications
11 Unpacking Your Refrigerator
11 Choosing the Proper Location
11 - Flooring
12 - Ambient Temperature
12 -Measuring the Clearances
I2 Removing/Assembling the Refrigerator
Door Handles
13 Removing/Assembling the Freezer
Drawer Handle
13 Removing/Assembling the Doors and
Drawers
13 - Removing the Left Refrigerator Door
14 - Removing the Right Refrigerator Door
15 - Assembling the Left Refrigerator Door
16 - Assembling the Right Refrigerator Door
16 - Removing the Freezer Drawers
18 - Assembling the Freezer Drawers
19 Connecting the Water Line
19 - Before You Begin
19 -Water Pressure
19 -What You Wilt Need
20 -Water Line Installation Instructions
22 Turning On the Power
23 Leveling and Door Alignment
23 - Leveling
23 - Door Alignment
24 HOWTOUSE
24 Before Use
25 Controt Panel
25 _Controi Panei Features
27 In-Door Ice Bin
27 - Detaching the In-Door Ice Bin
27 -Assembling the In-Door Ice Bin
28 Automatic Icemaker
28 -Turning the Automatic Icemaker On or
Off
29 -When You Should Turn the Icemaker Off
29 - Normal Sounds You May Hear
29 - Preparing for Vacation
30 tce and Water Dispenser
30 _Dispenser
30 - Using the Dispenser
30 - Locking the Dispenser
30 -Cleaning the Dispenser Stand
3t Storing Food
31 - Food Preservation Location
32 - Food Storage Tips
32 -Storing Frozen Food
33 Humidity Controlled Crisper
34 Detaching and Assembling the Storage Bins
35 Adjusting the Refrigerator Shelves
36 MAINTENANCE
36 Cleaning
37 Light butb replacement
37 Replacing the Fresh Air Filter
38 General Information
39 Replacing the Water Filter
43 SMART DIAGNOSIS
43 Using Smart Diagnosis
44 TROUBLESHOOTING
54 WARRANTY
PRODUCT FEATURES 3
PRODUCT FEATURES
* Depending on the model, some of the following functions may not be available.
FILTERED WATER AND ICE DISPENSER
The water dispenser dispenses fresh, chilled water.
The ice dispenser dispenses cubed and crushed ice.
DOOR ALARM
The Door Alarm function is designed to prevent refrigerator malfunctioning
that could occur if a refrigerator door or freezer drawer remains open. If a
refrigerator door or freezer drawer is left open for more than 60 seconds, a
warning alarm sounds in 30 second intervals.
HUMIDITY CONTROLLED CRISPER
The Humidity Controlled Crisper is designed to help keep your fruits and
vegetables fresh and crisp. You can controt the amount of humidity in the
crisper by adjusting the setting between Low and High.
GLIDE'N'SERVE
Glide'N'Serve provides storage space that keeps the compartment colder
than the refrigerator.
It is a convenient place to store sandwiches or meat to be cooked.
ICE PLUS
Ice production can be increased by approximately 20 percent when the
freezer section is maintained at the coldest temperature for a 24-hour
period.
4 IMPORTANT SAFETY INSTRUCTIONS
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
This guide contains many important safety messages. Always read and obey all safety messages
This is the safety alert symbol. It alerts you to safety messages that inform you of
hazards that can kill or hurt you or others, or cause damage to the product.
All safety messages will be preceded by the safety alert symbol and the hazard
signal word WARNING or CAUTION. These words mean:
_ WARNING You can be killed or seriously injured if you do not follow instructions.
_ CAUT!ON Indicates an imminently hazardous situation which, if not avoided, may result
in minor or moderate injury, or product damage.
_ WARNtNG
To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety
precautions should be followed, including the following.
Power
• NEVER unplug your refrigerator by pulling on the power cord. Always grip the plug firmly and
pull it straight out from the outlet.
• Immediately repair or replace all power cords that have become frayed or otherwise
damaged. Do not use a cord that shows cracks or abrasion damage along its length or at
either the plug or connector end.
• Do not use an uncertified power outlet.
• Unplug the power plug immediately in the event of a blackout or thunderstorm.
• Plug in the power plug with the power cord facing downward.
Installation
. Contact an authorized service center when you instalt or relocate the refrigerator.
° When moving your refrigerator away from the waN, be careful not to roN over or damage the
power cord.
• Connect this product to a dedicated grounded electric outlet conforming with the rating prior
to use. It is the user's responsibility to replace a standard 2-prong wall outlet with a standard
3-prong wall outlet.
. Do not install the refrigerator where there may be a danger of failing.
Use
• DO NOT allow children to climb, stand, or hang on the refrigerator doors or shelves in the
refrigerator. They could damage the refrigerator and seriously injure themselves.
• Do not place heavy objects on the dispenser of the refrigerator or hang onto it.
• Do not place heavy or dangerous objects (bottles with liquid} on the refrigerator.
• Do not put live animals inside of the refrigerator.
• Do not allow children to climb into the product when it is in use.
• In the event of a gas leak (propane/LPG), ventilate sufficiently and contact an authorized
service center before use. Do not touch or disassemble the electric outlet of the refrigerator.
• In the event of a refrigerant leak, move flammable objects away from the refrigerator.
Ventilate sufficiently and contact an authorized service center.
• Do not use or place flammable substances (chemicals, medicine, cosmetics, etc) near the
refrigerator or store them inside the refrigerator. Do not place the refrigerator in the vicinity
of flammable gas.
_ WARNING :This product contains chemicals known to the State of California
to cause cancer and birth defects or other reproductive harm. Wash hands after handling.
IMPORTANT SAFETY INSTRUCTIONS 5
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
• Do not use this product for special purposes (storage of medicine or test materials or for ships,
etc).
• Unplug the power plug before cleaning or repairing the refrigerator.
• When you replace the light bulb in the refrigerator, unplug the refrigerator or turn off the power.
Do not modify or extend the power cord.
• Do not use a dryer to dry the interior. Do not light a candle to remove the interior odor.
For your safety, this appliance must be properly grounded. Have the wall outlet and the circuit
checked by a qualified electrician to make sure the outlet is properly grounded.
• Do not use an outlet that can be turned off with a switch. Do not use an extension cord. It is the
user's responsibility to replace a standard 2-prong wall outlet with a standard 3-prong wall outlet.
• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord.
Do not use an adapter plug and plug the power plug into a multi-outlet extension cord.
Disconnect the power cord immediately if you hear a noise, smell a strange odor or detect
smoke.
Turn the power off if water or dust penetrates into the refrigerator. Call a service agent.
• Do not disassemble or modify the refrigerator.
• Do not put hands, feet, or metal objects below or behind the refrigerator.
Do not operate the refrigerator or touch the power cord with wet hands.
In refrigerators with automatic icemakers, avoid contact with the moving parts of the ejector
mechanism or with the heating element that releases the cubes. Do not place fingers or hands
on the automatic ice-making mechanism while the refrigerator is plugged in.
• When dispensing ice from the dispenser, do not use crystal ceramics.
• Do not touch the cold surfaces in the freezer compartment with wet or damp hands, when your
refrigerator is in operation.
• Do not put glass containers, glass bottles or soda in the freezer.
• This appliance is not intended for use by persons (including children) with reduced physical,
sensory or mental capabilities, or lack of experience and knowledge, unless they have been given
supervision or instruction concerning the use of the appliance by a person responsible for their
safety.
Do not refreeze frozen food that have thawed completely. It may result in a serious health issue.
• If you are throwing away your old refrigerator, make sure the CFC coolant is removed for proper
disposal by a qualified servicer. If you release CFC coolant, you may be fined or imprisoned in
accordance with the relevant environmental law.
• Junked or abandoned refrigerators are dangerous, even if they are sitting for only a few days.
When disposing the refrigerator, remove the packing materials from the door or take off the
doors but leave the shelves in place so that children may not easily climb inside.
6 IMPORTANT SAFETY INSTRUCT ONS
READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.
_ CAUTION
Installation
• The refrigerator must be properly installed in accordance with the Installer Instructions that
were taped to the front of the refrigerator.
o Be careful when you unpack and install the refrigerator. Immediately dispose of packing
materials (plastic) out of reach of children.
Use
• Close the door carefully when children are around.
• Keep fingers out of pinch point areas; clearances between the doors and cabinets are
necessarily small. Be careful closing doors when children are in the area.
• If you store food properly, beware that it may fall and cause injury.
Maintenance
• Do not use strong detergents like wax or thinners for cleaning. Clean with a soft fabric.
• Wipe foreign objects (dust, water, etc) off the prongs of the power plug and contact areas
regularly.
Supply Cord Replacement
If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly
qualified person in order to avoid a hazard.
_ WARNING
Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.
This appliance is intended to be used in household and similar applications such as staff kitchen areas
in shops, offices and other working environments;farm houses and by clients in hotels, motels and
other residential type environments; bed and breakfast type environments; catering and similar
non-retail applications.
_ WARNING
Connectto potablewater supplyonly.
Lamp Replacement
If LED lamp is damaged,it should be replaced by the service center in stead of on your own.
SAVE THESE INSTUCTIONS
COMPONENTS 7
COMPONENTS
Use this page to become more familiar with the parts and features of your refrigerator.
Page references are inctuded for your convenience,
*The appearance and specifications of the actual product may differ depending on the model.
Refrigerafor Exterior
LED Display
Displays the refrigerator and
freezer temperature, the water
filter condition and the dispenser
status.
Ice Plus
When this feature is activated,
the freezer section will run at the
coldest temperature for a 24-hour
period to increase ice production.
Filleted Wafer and
Ice Dispenser
Dispenses fresh, chilled,
filtered water through
the door. The ice
dispenser offers cubed
or crushed ice.
Door Alarm
A warning alarm sounds at 30-
second intervals when the
refrigerator or freezer door is left
open for more than 60 seconds.
8 COMPONENTS
Refrigerator inferior
LED Interior Lamps
The interior lamps light up the
inside of the refrigerator.
Water Filter
SpacePlus Ice System
Automatically produces
80-130 ice cubes in a
24-hour period.
Fixed Door Bins
Mullion I
Folds in when the
left door is opened.
Can Storage Bin
Used to preserve chilled
food or drinks.
Glide'N'Serve
Allows you to store food items
at a different temperature than
the regular refrigerator area.
Diagnosis Speaker
Hold your phone to this speaker when
activating Smart Diagnosis. Refer to the
Smart Diagnosis section for more details.
Fixed Door Bin
The shelves in your
_ efrigerator Shelves
refrigerator are adjustable
to meet your individual
storage needs.
-- Modular Door Bin
Fixed Door Bin
Crispers
Controls humidity and
helps vegetables and
fruit to stay crisp,
Top Drawer
Removable Ice Storage Bin --
The ice storage bin can be
removed to fill ice buckets,
coolers, or pitchers.
Bottom Drawer
--Divider
INSTALLATON 9
INSTALLATION
Installation Overview
Please read the following installation instructions first after purchasing this product or transporting
it to another location.
1 Unpacking your
refrigerator
4 Connecting the water 5 Leveling and Door
supply and water line Alignment
2 Choosing the proper
location
,..'3 Disassembling/Assembling
10 INSTALLATION
Specifications
The appearance and specifications listed in this manual may vary due to constant product
improvements.
Bottom-freezer refrigerator model LMXS27626*
Description French Door Refrigerator
Electrical requirements 11 5 VAC @ 60 Hz
Min./Max. Water pressure 20and120 psi (140 and 830 kPa)
Dimensions 35 3/4" (W) X 35 3/8" (D) X 69 3/4" (H), 47 5/8" (D w/door open)
908mm(W) X899mm(D)X 1772 (H), 1210 mm (D w/ door open)
Net weight 342 Ib, (155 kg)
INSTALLATION 11
Unpacking Your Refrigerator
"z_ WARNING
Use two or more people to move and
install the refrigerator. Failure to do so
can result in back or other injury,
. Your refrigerator is heavy. When moving
the refrigerator for cleaning or service,
be sure to protect the floor. Always pull
the refrigerator straight out when moving
it. Do not wiggle or walk the refrigerator
when trying to move it, as floor damage
could occur.
* Keep flammable materials and vapors,
such as gasoline, away from the
refrigerator. Failure to do so can result in
fire, explosion, or death
Remove tape and any temporary labels from your
refrigerator before using. Do not remove any
warning-type labels, the model and serial number
label, or the Tech Sheet that is located under the
front of the refrigerator.
To remove any remaining tape or glue, rub the
area briskly with your thumb. Tape or glue residue
can also be easily removed by rubbing a small
amount of liquid dish soap over the adhesive with
your fingers. Wipe with warm water and dry.
Do not use sharp instruments, rubbing alcohol,
flammable fluids, or abrasive cleaners to remove
tape or glue. These products can damage the
surface of your refrigerator.
Refrigerator shelves are installed in the shipping
position. Please reinstall shelves according to
your individual storage needs.
Choosing the Proper Location
Select a place where a water supply can
be easily connected for the automatic
icemaker.
_) NOTE
The water pressure must be between
20 and120 psi (140 and 830 kPa)
on models without a water filter and
between 40 and 120 psi (280 and 830
J
The refrigerator should always be plugged
into its own individual properly grounded
electrical outlet rated for 115 Volts, 60 Hz,
AC only, and fused at 15 or 20 amperes.
This provides the best performance
and also prevents overloading house
wiring circuits which could cause a fire
hazard from overheated wires. It is
recommended that a separate circuit
serving only this appliance be provided.
_Z_ WARNING --]
ITo reduce the risk of electric shock, do not
_install the refrigerator in a wet or damp
Flooring
To avoid noise and vibration, the unit must be
leveled and installed on a solidly constructed
floor. If required, adjust the leveling legs to
compensate for unevenness of the floor. The
front should be slightly higher than the rear to
aid in door closing. Leveling legs can be turned
easily by tipping the cabinet slightly, Turn the
leveling legs to the left to raise the unit or to
the right to lower it. (See Leveling and door
Alignment.)
.- _ NOTE
Installing on carpeting, soft tile surfaces
a platform or weakly supported structur_
12 INSTALLATION
Ambienf Temperafure
Install this appliance in an area where the
temperature is between 55°F (13°C) and 110°F
(43°C). If the temperature around the appliance
is too low or high, cooling ability may be
adversely affected.
Measuring fhe Clearances
Too small of a distance from adjacent items
may result in lowered freezing capability and
increased electricity consumption charges.
Allow at least 24 inches (61 cm) in front of
the refrigerator to open the doors, and at
least 2 inches (5 cm) between the back of the
refrigerator and the wall.
24" (61 crn)
t
2" (5 cm)
Removing/Assembling fhe
Refrigerator Door Handles
-iq- _ NOTE
emoving the doors is always
ecommended when it is necessary to
eve the refrigerator through a narrow
pening. If it is necessary to remove the
andles, follow the directions below.
Removing fhe Handles
Loosen the set screws D with a s/s2in.
Allen wrench and remove the handle.
Loosen the mounting fasteners _ that
connect to the refrigerator door and handle
using a 1/4in. Allen wrench, remove the
mounting fasteners.
Assembling 1"he Handles
1 Assemble the mounting fasteners D at
both ends of the handle using a _/4in.
Allen wrench.
2
Place the handle on the door by fitting
the handle footprints over the mounting
fasteners and tightening the set screws
with a s/szin. Allen wrench.
INSTALLATION 13
Removing/Assembling 1"he
Freezer Drawer Handle
Removing fhe Handles
1 Loosen the set screws D located on the
lower side of the handle with a _/8in. Alien
wrench and remove the handle.
Loosen the mounting fasteners _ that
connect to the freezer drawer and handle
using a V4in. Alien wrench, and remove
the mounting fasteners.
Assembling fhe Handles
1 Assemble the mounting fasteners D at
both ends of the handle using a 1/4in, Allen
wrench.
Place the handle on the door by fitting
the handle footprints over the mounting
fasteners and tightening the set screws
with a 1/sin. Allen wrench.
Removing/Assembling fhe
Doors and Drawers
Removing the doors is always recommended
when it is necessary to move the refrigerator
through a narrow opening,
FZ_ WARNING
• If your entrance door is too narrow for the
refrigerator to pass through, remove the
refrigerator doors and move the refrigerator
sideways through the doorway.
• Use two or more people to remove and
install the refrigerator doors. Failure to do
so can result in back or other injury.
o Disconnect the electrical supply to the
refrigerator before installing. Failure to do
so could result in serious injury or death.
Do not put hands, feet or other objects into
the air vents or bottom of the refrigerator.
You may be injured or receive an electrical
shock.
, Be careful when handling the hinge and
stopper. It may result in injury,
Remove food and bins from the doors and
drawers before detaching.
\
Removing fhe Left Refrigerafor Door
The water supply is connected to the
upper right part of the rear surface of the
refrigerator, Remove the ring in the joint
area, Hold the water supply connection
and gently push the Collet to detach the
water supply line as shown in O and _.
r_ NOTE -'I
Detachment ofthewater supplylineis
applicableonlywhen detachingthe left
14 INSTALLATION
Removing fhe Right Re{rigerafor Door
1__
(6)"_ ( )
(7) (4
2
Open the teft door. Remove the top hinge
cover screw (1). Lift up the cover (2).
Remove the cover.
3
4
Pull out the tube (3).
5
Disconnect all wire harnesses (4).
6
Remove the grounding screw (5).
7
Rotate the hinge lever (6)
counterclockwise. Lift the top hinge (7)
free of the hinge lever latch (8).
8
Lift the door from the middle hinge pin and
remove the door.
9
Place the door, inside facing up, on a non-
scratching surface.
-/k CAUTmO.
When lifting the hinge free of the latch, be I
careful that the door does not fall forward, lJ
/(2)
(3) (4) ,_,
1 Open the door, Remove the top hinge
cover screw (1), Lift up the cover (2),
2 Remove the cover.
3 Rotate the hinge lever (3) clockwise. Lift
the top hinge (4) free of the hinge lever
latch (5).
4 Lift the door from the middle hinge pin and
remove the door.
5 Place the door, inside facing up, on a non-
scratching surface.
[Wh CAUTION '1
en lifting the hinge free of the latch, be /
careful that the door does not fall forward 1
.s
Assembling fhe Left" Refrigerafor
Door
Install the left refrigerator door after the right
door is installed.
1 Lower the door onto the middle hinge pin.
(1)
.... (4)
(6)iJ_
(7)_ (8)
/
INSTALLATION 15
9 Insert the water supply tube at least 5/8 in.
(15 ram) into the connector.
10 Hook the tab on the door switch side
of the cover under the edge of the wire
opening in the cabinet top.
11 Position the cover into place. Insert and
tighten the cover screw.
-_-(!]_/ NOTE
2 Fit the top hinge (7) over the hinge lever
latch (8) and into place.
3 Rotate the lever (6) clockwise to secure
the hinge.
4 Install the grounding screws (5) and
connect the two wire harnesses (4).
5 Push the water tube (3) located at the top
of the left door into the hole beside the left
hinge on the top of the cabinet until it exits
through the back.
6 Insert the water supply tube (3) into the
connector until you see only one scale
mark. Fully insert the tub cover (15 mm).
7 Hook the tabs on the left side of the hinge
cover (1) under the edge of the top hinge (7)
and position the cover in place.
8 Insert and tighten the cover screw (1).
1) Gently press the Coltet and insert the
tube until only one line shows on the
tube.
(Correct)
(Incorrect)
2) Pull the tube to make sure that the
tube is tightly fastened and then insert
the clip.
16 INSTALLATION
Assembling fhe Right Refrigerafor
Door
Install the right-side door first,
Lower the door onto the middle hinge
pin. Make sure that the plastic sleeve is
inserted into the bottom of the door.
_(2)
)
2 Fit the top hinge (4) over the hinge lever
latch (5} and into place.
3 Rotate the lever (3) counterclockwise to
secure the hinge,
4 Hook the tabs on the right side of the
hinge cover (2) under the edge of the top
hinge (4) and position the cover in place.
5 Insert and tighten the cover screw (1).
Removing fhe Freezer Drawers
The top, middle and bottom drawers are all
removed in the same way. In the following
figures, the Pullout Drawer located above the
freezer drawer is not shown for clarity.
...._ CAUTION
• Use two or more people to remove and
install the freezer drawer. Failure to do so
can result in back or other injury.
• Do not hold the handle when removing
or replacing the drawer. The handle may
come off and it could cause personal
injury.
• Be careful of sharp hinges on both sides
of the drawer.
• When you lay the drawer down, be
careful not to damage the floor.
• Do not sit or stand on the freezer drawer.
=To prevent accidents, keep children and
pets away from the drawer. Do not leave
the drawer open.
TOP DRAWER
\ ...................................................................................................
1 Fullyextendthefreezerdrawer.Liftingupand
outto removethedrawerandicebinmaking
sureto cleartherailsystem.
Removeonewhitescrew_ oneachsideof
therails.
INSTALLATION 17
3 Holding both sides of the door pull up to
separate the door from the rails.
4 With bothhands,holdeachrail and push it in
toallow bothrailsto slideinsimultaneously.
_ CAUTION -'_
henyouremovethedrawer,do notholdthehandle,_
Ill itmaycomeoffanditcouldcausepersonalinjury.
IWhenplacingthedraweron thefloor, /
2 Remove onewhite screw 0 on each side of
the rails.
3 Holding both sides of the door pull up to
separate the door from the rails.
4 With both hands, hold each rail and push it in
to allow both rails to slidein simultaneously.
BOTTOMDRAWER
Fullyextend the freezer drawer. Lifting up and
out to remove the Dura Base basket making
sure to clear the rail system.
F_ CAUTION
"Whenyou removethe drawer,donotholdthehandle.
If it maycomeoffandit couldcausepersonalinjury.
°Whenplacingthedraweron the floor,careshouldbe
takentoavoidfloordamage.
J
18 BNSTALLAT_ON
Assembling the Freezer Drawer
TOPDRAWER
1 Withboth hands,pullout eachrail
simultaneouslyuntilbothrailsarefully
extended.
2 Hook door supports C) into rail tabs @.
_[_.wx WARRANTY ----]
To preventaccidentalchildandpetentrapmentorsuffocationrisk.I
/ DONOTallowthem to play inside of drawer.
BOTTOM DRAWER
1 With both hands, pull out each rail
simultaneously until both rails are fully extended.
i
2 Hook door supports (]) into rail tabs @.
/
3 Lower door into final position and tighten the
screws.
4 With the drawer pulled out to full extension,
insert the drawer and ice bin inthe rail
assembly.
3 Lower door into final position and tighten the
screws,
4 With the drawer pulled out to full extension,
insert the lower basket in the rail assembly.
Connecting the Water Line
INSTALLATION19
Be{ore You Begin
This water line installation is not covered by the
refrigerator warranty. Follow these instructions
carefully to minimize the risk of expensive water
damage.
Water hammer (water banging in the pipes) in
house plumbing can cause damage to refrigerator
parts and can lead to water leakage or flooding.
Call a qualified plumber to correct water hammer
before installing the water supply line to the
refrigerator.
" Z_ CAUTION
only connect the refrigerator water line to
To prevent burns and product damange,
a cold water supply.
If you use your refrigerator before connecting
the water line, make sure the icemaker power
switch is in the OFF (0) position.
-Z_ CAUTION --,
areas where temperatures fall below
Do not install the icemaker tubing in
freezing.
Water Pressure
A cold water supply. The water pressure must
be between 20 and 120 psi (140 and 830 kPa)
on models without a water filter and between
40 and 120 psi (280 and 830 kPa) on models
with a water filter.
If a reverse osmosis water filtration system is
connected to your cold water supply, this water
line installation is not covered by the refrigerator
warranty. Follow the following instructions
carefully to minimize the risk of expensive water
damage.
If a reverse osmosis water filtration system is
connected to your cold water supply, the water
pressure to the reverse osmosis system needs to
be a minimum of 40 to 60 psi ( 280 and 420 kPa ),
less than 2.0N3.0 sec. to fill a cup of 7 oz (200 cc)
capacity.
_-_ CAUTION
Wear eye protection during installation
to prevent injury.
If the water pressure from the reverse osmosis
system is less than 21 psi (145 kPa) (takes more
than 4.0 sec to fill a cup of 7 oz or 200cc capacity):
• Check to see if the sediment filter in
the reverse osmosis system is blocked.
Replace the filter if necessary.
• Allow the storage tank on the reverse
usage.
• If the issue concerning water pressure
from reverse osmosis remains, call a
licensed, qualified plumber.
• All installations must be in accordance
with local plumbing code requirements.
What You Will Need
Copper Tubing, 1_in. outer diameter, to
connect the refrigerator to the water
supply. Be sure both ends of the tubing
are cut square.
To determine how
much tubing you need:
measure the distance
from the water valve on the back of the
refrigerator to the water supply pipe.
Then, add 8 feet
(2.4 m). Be sure there is sufficient extra
tubing (about 8 feet [2.4 m] coiled into 3
turns of about 10 in. [25 cm] diameter)
to allow the refrigerator to move out
from the wall after installation.
o
Powerdrill.
o
V2in. or adjustable
wrench.
o
Flat blade and Phillips
e
head screwdrivers.
Two 1/4in. outer
diameter compression
nuts and 2 ferrules (sleeves) to connect the
copper tubing to the shutoff valve and
the refrigerator water valve.
20 INSTALLATION
* tf your existing copper water line has a
flared fitting at the end, you wilt need
an adapter (available at plumbing supply
stores) to connect the water line to the
refrigerator OR you can cut off the flared
fitting with a tube
cutter and then use a
compression fitting.
, Shutoff valve to
connectto the coldwater line, The shutoff
valve should have a water inlet with a
minimum inside diameter of 5/32 in. at
the point of connection to the COLD
WATER LINE. Saddletype shutoff valves
are included in many water supply kits.
Before purchasing,
make sure a saddle-
type valve complies
with your local
plumbing codes.
_ (2 NOTE
A self piercing saddle type water valve
should not be used.
Wafer Line Insfallafion Insfrucfions
"Z_ WARNING
When using any electrical device
(such as a power drill) during
installation, be sure the device is
battery powered, double insulated
or grounded in a manner that wilt
prevent the hazard of electric shock.
Install the shutoff valve on the nearest
frequently used drinking water line.
SHUT OFF THE MAIN WATER SUPPLY
Turn on the nearest faucet to relieve the
pressure on the line.
2 CHOOSE THE VALVE LOCATION
Choose a location for
the valve that is easily
accessible. It is best to
connect into the side of a
vertical water pipe. When
it is necessary to connect
into a horizontal water
pipe, make the connection to the top or
side, rather than at the bottom, to avoid
drawing off any sediment from the water
pipe.
3 DRILL THE HOLE FOR THE VALVE
Drill a 1Ain. hole in
the water pipe using
a sharp bit. Remove
any burrs resulting
from drilling the hole
in the pipe. Be careful
not to allow water
to drain into the drill. Failure to drill a 1Ain.
hole may result in reduced ice production
or smaller cubes.
_ NOTE ..................................
The hookup line cannot be white, plastic /
tubing. Licensed plumbers must use I
only copper tubing NDA tubing #49595 I
or 49599 or Cross Link Polyethylene I
]
INSTALLATION 21
4
FASTEN THE SHUTOFF VALVE 7
Fasten the shutoff valve to the cold water
pipe with the pipe clamp,
Pipe Clamp_
Saddle-Type _" _ _Vertical Cold
Shutoff Valve _ I Water Pipe
Commonwealth of Massachusetts
Plumbing Codes 248CMR shall be J
adhered to. Saddle valves are illegal and I
use is not permitted in Massachusetts,J 8
Consult with your licensed plumber. /
TIGHTEN THE PIPE CLAMP
Tighten the clamp screws until the sealing
washer begins to swell.
NOTE: Do not overfighten clamp or
you may crush the tubing.
-- Washer
Clamp Screw
Pipe Clamp _,
_ Inlet End
ROUTE THE TUBING
6
Route the tubing between the cold water
line and the refrigerator.
Route the tubing through a hole drilled in
the wall or floor (behind the refrigerator or
adjacent base cabinet) as close to the wail
as possible.
,-_ NOTE
Be sure there is sufficient extra tubing
(about 8 feet coiled into 3 turns of
about 10 in. diameter) to allow the
refrigerator to move out from the watt
after installation.
CONNECT THE TUBING TO THE VALVE
Place the compression nut and ferrule
(sleeve) for copper tubing onto the end of
the tubing and connect it to the shutoff
valve, Make sure the tubing is fully inserted
into the valve, Tighten the compression
nut securely,
Saddle-Type
Shutoff Valve __.
Packing Nu_ 1_
Outlet Valve _
Compression
\.... Ferrule (sleeve)
FLUSH OUT THE TUBING
Turn the main water
supply on and flush out
the tubing untit the water
is clear.
Shut the water off at the
water valve after about
one quart of water has
been flushed through the tubing.
CONNECT THE TUBING TO THE
9
REFRIGERATOR
NOTE: Before making the connection
to the refrigerator, be sure that the
refrigerator power cord is not plugged into
the wall outlet.
a. Remove the plastic flexible cap from
the water valve.
b, Place the compression nut and ferrule
(sbeve) onto the end of the tubing as
shown.
c. Insert the end of the copper tubing into
the connection as far as possible. While
holding the tubing, tighten the fitting.
Tubing Clamp /1-[_ ¼ in.Tubing
¼in. \ L_t / _/_
CotPression "X_ IllII/,.\ I
RefrigeratorConnection
22 INSTALLATION
10 TURN THE WATER ON AT THE SHUTOFF
VALVE
Tighten any connections that leak,
I _ CAUTION
Checktoseeif/eaks occur at the water
hneconnect_ons_
11 PLUG IN THE REFRIGERATOR
Arrange the coil of tubing so that it
does not vibrate against the back of the
refrigerator or against the wall, Push the
refrigerator back to the walt,
12 START THE ICEMAKER
Set the icemaker power switch to the ON
position,
The icemaker will not begin to operate
until it reaches its operating temperature
of 15°F (-9°C) or below. It wilt then begin
operation automatically if the icemaker
power switch is in the ON (I} position.
Turning On The Power
1 Plug in the refrigerator,
(_Z_ CAUTION
• Connect to a rated power outlet.
Have a certified electrician check
the wall outlet and wiring for proper
grounding,
Do not damage or cut off the ground
terminal of the power plug,
Leveling and Door Alignment
INSTALLATION 23
Leveling
After installing, plug the refrigerator's power
cord into a 3-prong grounded outlet and push
the refrigerator into the final position.
Your refrigerator has two front leveling legs--
one on the right and one on the left. Adjust the
legs to alter the tilt from front-to-back or side-
to-side, tf your refrigerator seems unsteady, or
you want the doors to close more easily, adjust
the refrigerator's tilt using the instructions
below:
Remove the base grille. Refer to the Base
Grille Installation section.
2
Turn the leveling leg to the left to raise
that side of the refrigerator or to the right
to lower it. It may take several turns of
the leveling leg to adjust the tilt of the
refrigerator.
Door Alignmenf
Both the left and right refrigerator doors have
an adjustable nut, located on the bottom hinge,
to raise and lower them to align properly.
If the space between your doors is uneven,
follow the instructions below to align the doors
evenly:
Use the wrench (included with the Owner's
Manual) to turn the nut in the door hinge to
adjust the height. To the right to raise or to the
left to lower the height.
A flare nut wrench works best, but an
open-end wrench will suffice.
NOTE 1
Do not over-tighten.
3
Open both doors again and check to make
sure that they close easily. If the doors do
not close easily, tilt the refrigerator slightly
more to the rear by turning both leveling
legs to the left. tt may take several more
turns, and you should turn both leveling
legs the same mount.
4 Replace the base grille.
24 HOW TO USE
HOW TO USE
Clean the refrigerator.
Clean your refrigerator thoroughly and wipe off all dust that accumulated during
shipping.
]_z_ CAUTION
I' Do not scratch the refrigerator with a sharp object or use a detergent that
contains alcohol, a flammable liquid or an abrasive when removing any tape
or adhesive from the refrigerator,.
I" Do not peel off the model or serial number label or the technical information
t on the rear surface of the refrigerator.
Remove adhesive residue by wiping it off with your thumb or dish detergent.
Connect the power supply.
Check if the power supply is connected before use.
Read the "Turning On The Power" section.
Turn off the icemaker if the refrigerator is not yet connected to the
water supply.
Turn off the automatic icemaker and then plug the power plug of the refrigerator
into the grounded electric outlet.
* This is applicable only to certain models.
unning the automatic icemaker before connecting it to the water
{_ CAUTION }
supply may cause the refrigerator to malfunction,
Waif for the refrigerator to cool.
Allow your refrigerator to run for at least two to three hours before putting food in
it. Check the flow of cold air in the freezer compartment to ensure proper cooling.
utting food in the refrigerator before it has cooled could cause the
-_ CAUTION 1
food to spoil, or a bad odor could remain inside the refrigerator.
The refrigerator makes a Joud noise after initial operation.
This is normal. The loudness will decrease as the temperature lowers.
Open refrigerator doors and freezer drawers to ventilate the inferior.
The inside of the refrigerator may smell like plastic at first. Remove any adhesive
tape from inside the refrigerator and open the refrigerator doors and the freezer
drawers for ventilation.
HOW TO USE 25
Confrol Panel
* Depending on the model, some of the following functions may not be available.
Confrol Panel F'eafures
The LED Display shows the temperature settings, dispenser options, water filter, door alarm, and
locking status messages.
Ice Type
Press the ICE TYPE button to seiect either
Crushed or Cubed Ice. The selected option will
illuminate on the LED display.
Freezer L'7OF
LED Display
Control
Buttons
Press the FREEZER button to adjust the
temperature in the freezer compartment.
NOTE
o change thedisplayfromFahrenheitto
elsius,pressand holdthe FREEZER and
Refrigerator ==_ i F
--#--I o
Press the REFRIGERATOR button to adjust the
temperature in the freezer compartment.
Ice Plus
This function increases both ice making and
freezing capabilities.
• When you touch the Ice Plus button, the
graphic will illuminate in the display and
will continue for 24 hours. The function will
automatically shut off after 24 hours.
• You can stop this function manually by
touching the button one more time.
26 HOW TO USE
Control Panel F'eafures (continued)
Fresh Air Filter
The Fresh Air Filter helps remove odors from the
refrigerator. The Fresh Air Filter has two settings,
Auto and Power(PWR). In Auto mode, the Fresh
Air Filter will cycle on and off in increments of ten
minutes on and one hundred ten minutes off. If
set to the Power(PWR) mode, the Fresh Air Filter
will stay on continuously for four hours, cycling on
and off in increments of ten minutes on and five
minutes off. After four hours, the Fresh Air Filter
wilt switch back to Auto mode.
Auto mode is the default mode.
• The Press the Air Filter button once for
Power(PWR) mode.
. Press the Air Filter button again to switch
back to Auto mode.
Light --O--
Press the LIGHT button, to turn on the
dispenser light. The indicator will appear on the
LED display.
Change Filter _
When the water filter indicator turns on, you
have to change the water filter. After changing
the water filter, press and hotd the FILTER
button for three seconds to turn the indicator
light off. You need to change the water filter
approximately every six months.
Alarm
Control Lock
The Control Lock function disables every other
button on the display.
When power is initially connected to the
refrigerator, the Lock function is off.
tf you want to activate the Lock function to
lock other buttons, press and hold the Lock
button for three seconds or more. The Lock
icon wilt display and the Lock function is
now enabled.
- To disable the Lock function, press and hold
the Lock button for approximately three
seconds.
--_ CAUTION
Display Mode (For Store Use Only)
The Display Mode disables all cooling
in the refrigerator and freezer sections
to conserve energy while on display in
a retail store. When activated, OFF will
display on the control panel.
To deactivate:
With either refrigerator door opened,
press and hold the Refrigerator and
Ice Plus buttons at the same time for
five seconds. The control panel will
beep and the temperature settings witl
display to confirm that Display Mode is
deactivated. Use the same procedure
to activate the Display Mode.
, When power is connected to the
refrigerator, the door alarm is initially set to
ON. When you press the ALARM button,
the display witl change to OFF and the
Alarm function wilt deactivate.
, When either the refrigerator or the freezer
door is left open for more than 60 seconds,
the alarm tone wilt sound to let you know
that the door is open.
. When you close the door, the door alarm
will stop.
in-Door Ice Bin
HOW TO USE 27
× Depending on the model, some of the
following functions may not be available.
'_"2_ CAUTION
, Keep hands and tools out of the ice
compartment door and dispenser chute.
Failure to do so may result in damage or
personal injury.
. The icemaker will stop producing ice when
the in-door ice bin is full. If you need more
ice, empty the ice bin into the extra ice bin
in the freezer compartment. During use,
the ice can become uneven causing the
icemaker to misread the amount of ice
cubes and stop producing ice. Shaking the
ice bin to level the ice within it can reduce
this problem.
. Storing cans or other items in the ice bin will
damage the icemaker.
• Keep the ice compartment door closed
tightly. If the ice compartment door is not
closed tightly, the cold air in the ice bin will
freeze food in the refrigerator compartment.
This could also cause the icemaker to stop
producing ice.
. If the ON/OFF switch on the icemaker is
set to OFF for an extended period of time,
the ice compartment will gradually warm
up to the temperature of the refrigerator
compartment. To prevent ice cubes from
melting and leaking from the dispenser,
ALWAYS empty the ice bin when the
icemaker is set to OFF for more than a few
hours.
2 To remove the in-door ice bin, grip the
front handle, slightly lift the lower part,
and slowly pull out the bin as shown.
Assembling the In-Door ice Bin
1 Carefully insert the in-door ice bin while
slightly slanting it to avoid contact with the
icemaker.
2 Avoid touching the ice-detecting sensor
when replacing the ice bin. See the label
on the ice compartment door for details.
Defaching the In-Door Ice Bin
1 Gently pull the handle to open the ice
compartment.
i[_ CAUTION
en handlingthe icebin,
eep hands away from the
emaker trayareatoavoid
ersonal injury.
X,.__j
28 HOW TO USE
Automatic Icemaker
Depending on the model, some of the
following functions may not be available.
Ice is made in the automatic icemaker and
sent to fhedispenser The icemaker will
produce 70-210 cubes in a 24-hour period,
depending on freezer compartment temperature,
room temperature, number of door openings and
other operating conditions.
* It fakes about 12 to 24 hours for a newly
installed refrigerator to begin making ice. Wait
72 hours for full ice production to occur
o Ice making stops when the in-door ice bin is fuji
When full, the in-door ice bin holds approximately
6 to 8 (12-16 oz or 340-455 cc) glasses of ice
° The water pressure must be between 20 and 120
psi (140 and 830 kPa)on models without a water
filter and between 40 and 120 psi (280 and 830
kPa) on models with a wafer filter to produce the
normal amount and size of ice cubes
* Foreign substances or frost on the ice-detecting
sensor can interrupt ice production
Make sure the sensor area is clean af all times
for proper operation
Wafer fills the ice fray.
1 hour later from
supplying wafer
* 60 minutes after water has been added
fo the ice tray, the ice tray wilI sit slightly
filled to help the cold air reach the ice.
Switch
ice-defecting
Icemaker
Sensor
* The ice-detecting sensors will sense
when the ice is ready to be dumped
into the ice bin
Turning the Automatic Icekarner
On or Off
To turn off the automatic icemaker, set the
icemaker switch to OFF (O) To turn on the
automatic icemaker, set the switch fo ON (I).
HOWTOUSE29
Automatic Icemaker
(continued)
Fz_ CAUTION
o The first ice and water dispensed may
include particles or odor from the water
supply line or the water tanL
• Throw away the first few batches of ice
(about 24 cubes). This is also necessary if
the refrigerator has not been used for a long
time.
= Never store beverage cans or other items in
the ice bin for the purpose of rapid cooling.
Doing so may damage the icemaker or the
containers may burst.
= tf discolored ice is dispensed, check the
water filter and water supply. If the problem
continues, contact a Sears or other qualified
service center. Do not use the ice or water
until the problem is corrected.
• Keep children away from the dispenser.
Children may play with or damage the
controls.
• The ice passage may become blocked with
frost if only crushed ice is used. Remove the
frost that accumulates by removing the ice
bin and clearing the passage with a rubber
spatula. Dispensing cubed ice can also help
prevent frost buildup.
= Never use thin crystal glass or crockery to
collect ice. Such containers may chip or
break resulting in glass fragments in the ice.
= Dispense ice into a glass before filling it
with water or other beverages. Splashing
may occur if ice is dispensed into a glass
that already contains liquid.
Never use a glass that is exceptionally
narrow or deep. Ice may jam in the ice
passage and refrigerator performance may
be affected.
Keep the glass at a proper distance from
the ice outlet. A glass held too close to the
outlet may prevent ice from dispensing.
• To avoid personal injury, keep hands out of
the ice door and passage.
= Never remove the dispenser cover.
tf ice or water dispenses unexpectedly, turn
off the water supply and contact a qualified
service center.
When You Should Turn the
lcemaker Off
• When the water supply will be shut off
for several hours.
When the ice bin is removed for more
than one or two minutes.
• When the refrigerator witl not be used
for several days.
@NOTE /
he ice bin should be emptied when the
cemaker on!off switch is turned to the
OFF position.
Normal Sounds You May Hear
= The icemaker water valve will buzz as
the icemaker fills with water, tf the
power switch is in the ON (I) position,
it will buzz even if it has not yet been
hooked up to water. To stop the buzzing,
move the power switch to OFF (0).
Keeping the power switch in the ON
(I) position before the water line is
connected can damage the icemaker.
° You will hear the sound of cubes
dropping into the bin and water running
in the pipes as the icemaker refills.
Preparing for Vacation
Set the icemaker power switch to OFF (0) and
shut off the water supply to the refrigerator,
'T( _ NOTE
he icebinshouldbe emptied anytime
he ieemakeron/offswitchisturnedto
the OFF (0) position. ._
if the ambient temperature will drop below
freezing, have a qualified technician drain
the water supply system to prevent serious
property damage due to flooding caused by
ruptured water lines or connections.
30 HOW TO USE
Ice and Wafer Dispenser
* Depending on the model, some of the
following functions may not be available.
I K_'w CAUTION "/
eep children away from the dispenser.
Children may play with or damage the
controls.
Dispenser
Water Switch
ice Switch
Stand
Using the Dispenser
* To dispense cold water, push on the
water switch with a glass.
- To dispense ice, push on the ice switch
with a glass.
InoorreotWayc0rrectWay
Water
Ice
-_ CAUTION
hrow away the first few batches of ice
about 24 cubes). This is also necessary
f the refrigerator has not been used for
long time
Locking fhe Dispenser
Press and hold the Alarm and Lock button
simultainously for 3 seconds to lock the
dispenser and all the controt panel functions.
Follow the same instructions to unlock.
- _ NOTE
. If discolored ice is dispensed, check
the water filter and water supply. If the
problem continues, contact a qualified
service center. Do not use the ice or
water until the problem is corrected.
* The dispenser will not operate when
either of the refrigerator doors are open.
. If dispensing water or ice into a container
with a smalt opening, place it as close to
the dispenser as possible.
Some dripping may occur after
dispensing. Hold your cup beneath
the dispenser for a few seconds after
dispensing to catch all of the drops.
\
Cleaning fhe Dispenser Sfand
1 Grip the stand with both hands and pull it
out.
2 Wipe out dirty areas with a clean cloth.