LG LMXS27626S/01, LMXS27626S/00, LMXS27626D/01, LMXS27626D/00 Owner’s Manual

Life's Good

FRE CH DOOR

REFRIGERATOR

Please read 1his owners manuaO thoroughly before operating and keep if handy for reference at al8 times.

LMXS27626 -_

P/No,: MFL68680402

2 TABLEOFCONTENTS

TABLE OF CONTENTS

3 PRODUCT FEATURES

4 IMPORTANT SAFETY

INSTRUCTIONS

7 COMPONENTS

7 Refrigerator Exterior 8 Refrigerator Interior

INSTALLATION

9 Installation Overview 10 Specifications

11 Unpacking Your Refrigerator 11 Choosing the Proper Location

11 - Flooring 12 - Ambient Temperature

12 -Measuring the Clearances I2 Removing/Assembling the Refrigerator

Door Handles

13 Removing/Assembling the Freezer

Drawer Handle

13 Removing/Assembling the Doors and

Drawers

13 - Removing the Left Refrigerator Door 14 - Removing the Right Refrigerator Door

15 - Assembling the Left Refrigerator Door 16 - Assembling the Right Refrigerator Door 16 - Removing the Freezer Drawers

18 - Assembling the Freezer Drawers 19 Connecting the Water Line

19 - Before You Begin 19 -Water Pressure 19 -What You Wilt Need

20 -Water Line Installation Instructions 22 Turning On the Power

23 Leveling and Door Alignment 23 - Leveling

23 - Door Alignment

24 HOWTOUSE

24 Before Use 25 Controt Panel

25 _Controi Panei Features 27 In-Door Ice Bin 27 - Detaching the In-Door Ice Bin

27 -Assembling the In-Door Ice Bin 28 Automatic Icemaker

28 -Turning the Automatic Icemaker On or

Off 29 -When You Should Turn the Icemaker Off 29 - Normal Sounds You May Hear

29 - Preparing for Vacation 30 tce and Water Dispenser

30 _Dispenser 30 - Using the Dispenser

30 - Locking the Dispenser 30 -Cleaning the Dispenser Stand

3t Storing Food 31 - Food Preservation Location

32 - Food Storage Tips 32 -Storing Frozen Food

33 Humidity Controlled Crisper 34 Detaching and Assembling the Storage Bins

35 Adjusting the Refrigerator Shelves

36 MAINTENANCE

36 Cleaning 37 Light butb replacement 37 Replacing the Fresh Air Filter

38 General Information 39 Replacing the Water Filter

43 SMART DIAGNOSIS

43 Using Smart Diagnosis

44 TROUBLESHOOTING

54 WARRANTY

PRODUCT FEATURES 3

PRODUCT FEATURES

* Depending on the model, some of the following functions may not be available.

FILTERED WATER AND ICE DISPENSER

The water dispenser dispenses fresh, chilled water. The ice dispenser dispenses cubed and crushed ice.

DOOR ALARM

The Door Alarm function is designed to prevent refrigerator malfunctioning that could occur if a refrigerator door or freezer drawer remains open. If a refrigerator door or freezer drawer is left open for more than 60 seconds, a

warning alarm sounds in 30 second intervals.

HUMIDITY CONTROLLED CRISPER

The Humidity Controlled Crisper is designed to help keep your fruits and vegetables fresh and crisp. You can controt the amount of humidity in the

crisper by adjusting the setting between Low and High.

GLIDE'N'SERVE Glide'N'Serve provides storage space that keeps the compartment colder

than the refrigerator.

It is a convenient place to store sandwiches or meat to be cooked.

ICE PLUS Ice production can be increased by approximately 20 percent when the

freezer section is maintained at the coldest temperature for a 24-hour period.

4 IMPORTANT SAFETY INSTRUCTIONS

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

This guide contains many important safety messages. Always read and obey all safety messages

This is the safety alert symbol. It alerts you to safety messages that inform you of hazards that can kill or hurt you or others, or cause damage to the product.

All safety messages will be preceded by the safety alert symbol and the hazard signal word WARNING or CAUTION. These words mean:

_ WARNING You can be killed or seriously injured if you do not follow instructions.

_ CAUT!ON Indicates an imminently hazardous situation which, if not avoided, may result

in minor or moderate injury, or product damage.

_ WARNtNG

To reduce the risk of fire, electric shock, or personal injury when using your product, basic safety

precautions should be followed, including the following.

Power

• NEVER unplug your refrigerator by pulling on the power cord. Always grip the plug firmly and pull it straight out from the outlet.

• Immediately repair or replace all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at

either the plug or connector end.

• Do not use an uncertified power outlet.

• Unplug the power plug immediately in the event of a blackout or thunderstorm.

• Plug in the power plug with the power cord facing downward.

Installation

. Contact an authorized service center when you instalt or relocate the refrigerator. ° When moving your refrigerator away from the waN, be careful not to roN over or damage the

power cord.

• Connect this product to a dedicated grounded electric outlet conforming with the rating prior to use. It is the user's responsibility to replace a standard 2-prong wall outlet with a standard

3-prong wall outlet.

. Do not install the refrigerator where there may be a danger of failing.

Use

• DO NOT allow children to climb, stand, or hang on the refrigerator doors or shelves in the refrigerator. They could damage the refrigerator and seriously injure themselves.

• Do not place heavy objects on the dispenser of the refrigerator or hang onto it.

• Do not place heavy or dangerous objects (bottles with liquid} on the refrigerator.

• Do not put live animals inside of the refrigerator.

• Do not allow children to climb into the product when it is in use.

• In the event of a gas leak (propane/LPG), ventilate sufficiently and contact an authorized service center before use. Do not touch or disassemble the electric outlet of the refrigerator.

• In the event of a refrigerant leak, move flammable objects away from the refrigerator. Ventilate sufficiently and contact an authorized service center.

• Do not use or place flammable substances (chemicals, medicine, cosmetics, etc) near the refrigerator or store them inside the refrigerator. Do not place the refrigerator in the vicinity

of flammable gas.

_ WARNING :This product contains chemicals known to the State of California

to cause cancer and birth defects or other reproductive harm. Wash hands after handling.

IMPORTANT SAFETY INSTRUCTIONS 5

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

• Do not use this product for special purposes (storage of medicine or test materials or for ships, etc).

• Unplug the power plug before cleaning or repairing the refrigerator.

• When you replace the light bulb in the refrigerator, unplug the refrigerator or turn off the power. Do not modify or extend the power cord.

• Do not use a dryer to dry the interior. Do not light a candle to remove the interior odor. For your safety, this appliance must be properly grounded. Have the wall outlet and the circuit

checked by a qualified electrician to make sure the outlet is properly grounded.

• Do not use an outlet that can be turned off with a switch. Do not use an extension cord. It is the user's responsibility to replace a standard 2-prong wall outlet with a standard 3-prong wall outlet.

• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Do not use an adapter plug and plug the power plug into a multi-outlet extension cord.

Disconnect the power cord immediately if you hear a noise, smell a strange odor or detect smoke.

Turn the power off if water or dust penetrates into the refrigerator. Call a service agent.

• Do not disassemble or modify the refrigerator.

• Do not put hands, feet, or metal objects below or behind the refrigerator. Do not operate the refrigerator or touch the power cord with wet hands.

In refrigerators with automatic icemakers, avoid contact with the moving parts of the ejector mechanism or with the heating element that releases the cubes. Do not place fingers or hands

on the automatic ice-making mechanism while the refrigerator is plugged in.

• When dispensing ice from the dispenser, do not use crystal ceramics.

• Do not touch the cold surfaces in the freezer compartment with wet or damp hands, when your refrigerator is in operation.

• Do not put glass containers, glass bottles or soda in the freezer.

• This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning the use of the appliance by a person responsible for their

safety. Do not refreeze frozen food that have thawed completely. It may result in a serious health issue.

• If you are throwing away your old refrigerator, make sure the CFC coolant is removed for proper disposal by a qualified servicer. If you release CFC coolant, you may be fined or imprisoned in

accordance with the relevant environmental law.

• Junked or abandoned refrigerators are dangerous, even if they are sitting for only a few days. When disposing the refrigerator, remove the packing materials from the door or take off the

doors but leave the shelves in place so that children may not easily climb inside.

6 IMPORTANT SAFETY INSTRUCT ONS

READ ALL INSTRUCTIONS BEFORE USING THE APPLIANCE.

_ CAUTION

Installation

• The refrigerator must be properly installed in accordance with the Installer Instructions that were taped to the front of the refrigerator.

o Be careful when you unpack and install the refrigerator. Immediately dispose of packing

materials (plastic) out of reach of children.

Use

• Close the door carefully when children are around.

• Keep fingers out of pinch point areas; clearances between the doors and cabinets are

necessarily small. Be careful closing doors when children are in the area.

• If you store food properly, beware that it may fall and cause injury.

Maintenance

• Do not use strong detergents like wax or thinners for cleaning. Clean with a soft fabric.

• Wipe foreign objects (dust, water, etc) off the prongs of the power plug and contact areas

regularly.

Supply Cord Replacement If the supply cord is damaged, it must be replaced by the manufacturer or its service agent or a similarly

qualified person in order to avoid a hazard.

_ WARNING Do not store explosive substances such as aerosol cans with a flammable propellant in this appliance.

This appliance is intended to be used in household and similar applications such as staff kitchen areas in shops, offices and other working environments;farm houses and by clients in hotels, motels and other residential type environments; bed and breakfast type environments; catering and similar

non-retail applications.

_ WARNING Connectto potablewater supplyonly.

Lamp Replacement

If LED lamp is damaged,it should be replaced by the service center in stead of on your own.

SAVE THESE INSTUCTIONS

COMPONENTS 7

COMPONENTS

Use this page to become more familiar with the parts and features of your refrigerator. Page references are inctuded for your convenience,

*The appearance and specifications of the actual product may differ depending on the model.

Refrigerafor Exterior

LED Display Displays the refrigerator and

freezer temperature, the water filter condition and the dispenser

status.

Ice Plus When this feature is activated,

the freezer section will run at the coldest temperature for a 24-hour

period to increase ice production.

Filleted Wafer and Ice Dispenser

Dispenses fresh, chilled, filtered water through the door. The ice

dispenser offers cubed or crushed ice.

Door Alarm A warning alarm sounds at 30-

second intervals when the refrigerator or freezer door is left

open for more than 60 seconds.

8 COMPONENTS

Refrigerator inferior

LED Interior Lamps

The interior lamps light up the inside of the refrigerator.

Water Filter

SpacePlus Ice System

Automatically produces 80-130 ice cubes in a

24-hour period.

Fixed Door Bins

Mullion I Folds in when the

left door is opened.

Can Storage Bin

Used to preserve chilled

food or drinks.

Glide'N'Serve

Allows you to store food items at a different temperature than

the regular refrigerator area.

Diagnosis Speaker

Hold your phone to this speaker when activating Smart Diagnosis. Refer to the Smart Diagnosis section for more details.

Fixed Door Bin

The shelves in your

_ efrigerator Shelves

refrigerator are adjustable to meet your individual storage needs.

-- Modular Door Bin

Fixed Door Bin

Crispers Controls humidity and

helps vegetables and fruit to stay crisp,

Top Drawer

Removable Ice Storage Bin --

The ice storage bin can be

removed to fill ice buckets,

coolers, or pitchers.

Bottom Drawer

--Divider

INSTALLATON 9

INSTALLATION

Installation Overview

Please read the following installation instructions first after purchasing this product or transporting

it to another location.

1 Unpacking your

refrigerator

4 Connecting the water 5 Leveling and Door

supply and water line Alignment

2 Choosing the proper

location

,..'3 Disassembling/Assembling

10 INSTALLATION

Specifications

The appearance and specifications listed in this manual may vary due to constant product improvements.

Bottom-freezer refrigerator model LMXS27626* Description French Door Refrigerator Electrical requirements 11 5 VAC @ 60 Hz

Min./Max. Water pressure 20and120 psi (140 and 830 kPa) Dimensions 35 3/4" (W) X 35 3/8" (D) X 69 3/4" (H), 47 5/8" (D w/door open)

908mm(W) X899mm(D)X 1772 (H), 1210 mm (D w/ door open)

Net weight 342 Ib, (155 kg)

INSTALLATION 11

Unpacking Your Refrigerator

"z_ WARNING

Use two or more people to move and

install the refrigerator. Failure to do so can result in back or other injury,

. Your refrigerator is heavy. When moving

the refrigerator for cleaning or service, be sure to protect the floor. Always pull

the refrigerator straight out when moving it. Do not wiggle or walk the refrigerator

when trying to move it, as floor damage could occur.

* Keep flammable materials and vapors,

such as gasoline, away from the

refrigerator. Failure to do so can result in

fire, explosion, or death

Remove tape and any temporary labels from your refrigerator before using. Do not remove any

warning-type labels, the model and serial number label, or the Tech Sheet that is located under the

front of the refrigerator.

To remove any remaining tape or glue, rub the area briskly with your thumb. Tape or glue residue can also be easily removed by rubbing a small

amount of liquid dish soap over the adhesive with your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol, flammable fluids, or abrasive cleaners to remove

tape or glue. These products can damage the surface of your refrigerator.

Refrigerator shelves are installed in the shipping position. Please reinstall shelves according to

your individual storage needs.

Choosing the Proper Location

Select a place where a water supply can be easily connected for the automatic

icemaker.

_) NOTE

The water pressure must be between 20 and120 psi (140 and 830 kPa) on models without a water filter and

between 40 and 120 psi (280 and 830

The refrigerator should always be plugged into its own individual properly grounded electrical outlet rated for 115 Volts, 60 Hz,

AC only, and fused at 15 or 20 amperes. This provides the best performance

and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires. It is

recommended that a separate circuit serving only this appliance be provided.

_Z_ WARNING --] ITo reduce the risk of electric shock, do not

_install the refrigerator in a wet or damp

Flooring

To avoid noise and vibration, the unit must be leveled and installed on a solidly constructed floor. If required, adjust the leveling legs to

compensate for unevenness of the floor. The front should be slightly higher than the rear to

aid in door closing. Leveling legs can be turned easily by tipping the cabinet slightly, Turn the leveling legs to the left to raise the unit or to

the right to lower it. (See Leveling and door Alignment.)

.- _ NOTE

Installing on carpeting, soft tile surfaces

a platform or weakly supported structur_

12 INSTALLATION

Ambienf Temperafure

Install this appliance in an area where the

temperature is between 55°F (13°C) and 110°F

(43°C). If the temperature around the appliance is too low or high, cooling ability may be

adversely affected.

Measuring fhe Clearances Too small of a distance from adjacent items

may result in lowered freezing capability and increased electricity consumption charges.

Allow at least 24 inches (61 cm) in front of the refrigerator to open the doors, and at

least 2 inches (5 cm) between the back of the refrigerator and the wall.

24" (61 crn)

2" (5 cm)

Removing/Assembling fhe Refrigerator Door Handles

-iq- _ NOTE emoving the doors is always

ecommended when it is necessary to

eve the refrigerator through a narrow

pening. If it is necessary to remove the andles, follow the directions below.

Removing fhe Handles

Loosen the set screws D with a s/s2in.

Allen wrench and remove the handle.

Loosen the mounting fasteners _ that

connect to the refrigerator door and handle using a 1/4in. Allen wrench, remove the

mounting fasteners.

Assembling 1"he Handles

1 Assemble the mounting fasteners D at

both ends of the handle using a _/4in. Allen wrench.

Place the handle on the door by fitting the handle footprints over the mounting

fasteners and tightening the set screws with a s/szin. Allen wrench.

INSTALLATION 13

Removing/Assembling 1"he Freezer Drawer Handle

Removing fhe Handles

1 Loosen the set screws D located on the

lower side of the handle with a _/8in. Alien wrench and remove the handle.

Loosen the mounting fasteners _ that connect to the freezer drawer and handle

using a V4in. Alien wrench, and remove the mounting fasteners.

Assembling fhe Handles

1 Assemble the mounting fasteners D at

both ends of the handle using a 1/4in, Allen wrench.

Place the handle on the door by fitting the handle footprints over the mounting

fasteners and tightening the set screws with a 1/sin. Allen wrench.

Removing/Assembling fhe Doors and Drawers

Removing the doors is always recommended

when it is necessary to move the refrigerator through a narrow opening,

FZ_ WARNING

• If your entrance door is too narrow for the refrigerator to pass through, remove the

refrigerator doors and move the refrigerator

sideways through the doorway.

• Use two or more people to remove and install the refrigerator doors. Failure to do

so can result in back or other injury.

o Disconnect the electrical supply to the

refrigerator before installing. Failure to do

so could result in serious injury or death.

Do not put hands, feet or other objects into

the air vents or bottom of the refrigerator. You may be injured or receive an electrical shock.

, Be careful when handling the hinge and

stopper. It may result in injury,

Remove food and bins from the doors and

drawers before detaching.

Removing fhe Left Refrigerafor Door

The water supply is connected to the

upper right part of the rear surface of the refrigerator, Remove the ring in the joint

area, Hold the water supply connection and gently push the Collet to detach the

water supply line as shown in O and _.

r_ NOTE -'I

Detachment ofthewater supplylineis applicableonlywhen detachingthe left

14 INSTALLATION

Removing fhe Right Re{rigerafor Door

1__

(6)"_ ( )

(7) (4

Open the teft door. Remove the top hinge cover screw (1). Lift up the cover (2).

Remove the cover.

Pull out the tube (3).

Disconnect all wire harnesses (4).

Remove the grounding screw (5).

Rotate the hinge lever (6) counterclockwise. Lift the top hinge (7)

free of the hinge lever latch (8).

Lift the door from the middle hinge pin and remove the door.

Place the door, inside facing up, on a non- scratching surface.

-/k CAUTmO.

When lifting the hinge free of the latch, be I careful that the door does not fall forward, lJ

/(2)

(3) (4) ,_,

1 Open the door, Remove the top hinge

cover screw (1), Lift up the cover (2),

2 Remove the cover.

3 Rotate the hinge lever (3) clockwise. Lift

the top hinge (4) free of the hinge lever latch (5).

4 Lift the door from the middle hinge pin and

remove the door.

5 Place the door, inside facing up, on a non-

scratching surface.

[Wh CAUTION '1

en lifting the hinge free of the latch, be /

careful that the door does not fall forward 1

Assembling fhe Left" Refrigerafor

Door

Install the left refrigerator door after the right door is installed.

1 Lower the door onto the middle hinge pin.

(1)

.... (4)

(6)iJ_

(7)_ (8)

INSTALLATION 15

9 Insert the water supply tube at least 5/8 in.

(15 ram) into the connector.

10 Hook the tab on the door switch side

of the cover under the edge of the wire opening in the cabinet top.

11 Position the cover into place. Insert and

tighten the cover screw.

-_-(!]_/ NOTE

2 Fit the top hinge (7) over the hinge lever

latch (8) and into place.

3 Rotate the lever (6) clockwise to secure

the hinge.

4 Install the grounding screws (5) and

connect the two wire harnesses (4).

5 Push the water tube (3) located at the top

of the left door into the hole beside the left hinge on the top of the cabinet until it exits through the back.

6 Insert the water supply tube (3) into the

connector until you see only one scale mark. Fully insert the tub cover (15 mm).

7 Hook the tabs on the left side of the hinge

cover (1) under the edge of the top hinge (7) and position the cover in place.

8 Insert and tighten the cover screw (1).

1) Gently press the Coltet and insert the tube until only one line shows on the

tube.

(Correct)

(Incorrect)

2) Pull the tube to make sure that the tube is tightly fastened and then insert the clip.

16 INSTALLATION

Assembling fhe Right Refrigerafor

Door

Install the right-side door first,

Lower the door onto the middle hinge pin. Make sure that the plastic sleeve is

inserted into the bottom of the door.

_(2)

)

2 Fit the top hinge (4) over the hinge lever

latch (5} and into place.

3 Rotate the lever (3) counterclockwise to

secure the hinge,

4 Hook the tabs on the right side of the

hinge cover (2) under the edge of the top hinge (4) and position the cover in place.

5 Insert and tighten the cover screw (1).

Removing fhe Freezer Drawers

The top, middle and bottom drawers are all removed in the same way. In the following

figures, the Pullout Drawer located above the freezer drawer is not shown for clarity.

...._ CAUTION

• Use two or more people to remove and install the freezer drawer. Failure to do so

can result in back or other injury.

• Do not hold the handle when removing or replacing the drawer. The handle may

come off and it could cause personal injury.

• Be careful of sharp hinges on both sides of the drawer.

• When you lay the drawer down, be careful not to damage the floor.

• Do not sit or stand on the freezer drawer.

=To prevent accidents, keep children and

pets away from the drawer. Do not leave the drawer open.

TOP DRAWER

\ ...................................................................................................

1 Fullyextendthefreezerdrawer.Liftingupand

outto removethedrawerandicebinmaking sureto cleartherailsystem.

Removeonewhitescrew_ oneachsideof

therails.

INSTALLATION 17

3 Holding both sides of the door pull up to

separate the door from the rails.

4 With bothhands,holdeachrail and push it in

toallow bothrailsto slideinsimultaneously.

_ CAUTION -'_

henyouremovethedrawer,do notholdthehandle,_

Ill itmaycomeoffanditcouldcausepersonalinjury. IWhenplacingthedraweron thefloor, /

2 Remove onewhite screw 0 on each side of

the rails.

3 Holding both sides of the door pull up to

separate the door from the rails.

4 With both hands, hold each rail and push it in

to allow both rails to slidein simultaneously.

BOTTOMDRAWER

Fullyextend the freezer drawer. Lifting up and out to remove the Dura Base basket making sure to clear the rail system.

F_ CAUTION

"Whenyou removethe drawer,donotholdthehandle.

If it maycomeoffandit couldcausepersonalinjury.

°Whenplacingthedraweron the floor,careshouldbe

takentoavoidfloordamage.

18 BNSTALLAT_ON

Assembling the Freezer Drawer TOPDRAWER

1 Withboth hands,pullout eachrail

simultaneouslyuntilbothrailsarefully

extended.

2 Hook door supports C) into rail tabs @.

_[_.wx WARRANTY ----]

To preventaccidentalchildandpetentrapmentorsuffocationrisk.I

/ DONOTallowthem to play inside of drawer.

BOTTOM DRAWER

1 With both hands, pull out each rail

simultaneously until both rails are fully extended.

2 Hook door supports (]) into rail tabs @.

3 Lower door into final position and tighten the

screws.

4 With the drawer pulled out to full extension,

insert the drawer and ice bin inthe rail assembly.

3 Lower door into final position and tighten the

screws,

4 With the drawer pulled out to full extension,

insert the lower basket in the rail assembly.

Connecting the Water Line

INSTALLATION19

Be{ore You Begin

This water line installation is not covered by the

refrigerator warranty. Follow these instructions carefully to minimize the risk of expensive water

damage.

Water hammer (water banging in the pipes) in

house plumbing can cause damage to refrigerator parts and can lead to water leakage or flooding.

Call a qualified plumber to correct water hammer before installing the water supply line to the

refrigerator.

" Z_ CAUTION

only connect the refrigerator water line to To prevent burns and product damange, a cold water supply.

If you use your refrigerator before connecting

the water line, make sure the icemaker power

switch is in the OFF (0) position.

-Z_ CAUTION --,

areas where temperatures fall below

Do not install the icemaker tubing in

freezing.

Water Pressure

A cold water supply. The water pressure must

be between 20 and 120 psi (140 and 830 kPa) on models without a water filter and between

40 and 120 psi (280 and 830 kPa) on models with a water filter.

If a reverse osmosis water filtration system is

connected to your cold water supply, this water

line installation is not covered by the refrigerator warranty. Follow the following instructions carefully to minimize the risk of expensive water

damage.

If a reverse osmosis water filtration system is connected to your cold water supply, the water pressure to the reverse osmosis system needs to

be a minimum of 40 to 60 psi ( 280 and 420 kPa ),

less than 2.0N3.0 sec. to fill a cup of 7 oz (200 cc)

capacity.

_-_ CAUTION

Wear eye protection during installation to prevent injury.

If the water pressure from the reverse osmosis system is less than 21 psi (145 kPa) (takes more

than 4.0 sec to fill a cup of 7 oz or 200cc capacity):

• Check to see if the sediment filter in the reverse osmosis system is blocked.

Replace the filter if necessary.

• Allow the storage tank on the reverse usage.

• If the issue concerning water pressure from reverse osmosis remains, call a

licensed, qualified plumber.

• All installations must be in accordance with local plumbing code requirements.

What You Will Need

Copper Tubing, 1_in. outer diameter, to

connect the refrigerator to the water supply. Be sure both ends of the tubing

are cut square. To determine how

much tubing you need: measure the distance

from the water valve on the back of the refrigerator to the water supply pipe.

Then, add 8 feet (2.4 m). Be sure there is sufficient extra tubing (about 8 feet [2.4 m] coiled into 3

turns of about 10 in. [25 cm] diameter) to allow the refrigerator to move out

from the wall after installation.

Powerdrill.

V2in. or adjustable wrench.

Flat blade and Phillips

head screwdrivers.

Two 1/4in. outer

diameter compression

nuts and 2 ferrules (sleeves) to connect the copper tubing to the shutoff valve and

the refrigerator water valve.

20 INSTALLATION

* tf your existing copper water line has a

flared fitting at the end, you wilt need an adapter (available at plumbing supply stores) to connect the water line to the

refrigerator OR you can cut off the flared fitting with a tube

cutter and then use a compression fitting.

, Shutoff valve to

connectto the coldwater line, The shutoff valve should have a water inlet with a minimum inside diameter of 5/32 in. at the point of connection to the COLD WATER LINE. Saddletype shutoff valves

are included in many water supply kits. Before purchasing,

make sure a saddle- type valve complies

with your local plumbing codes.

_ (2 NOTE

A self piercing saddle type water valve should not be used.

Wafer Line Insfallafion Insfrucfions

"Z_ WARNING

When using any electrical device

(such as a power drill) during installation, be sure the device is

battery powered, double insulated or grounded in a manner that wilt prevent the hazard of electric shock.

Install the shutoff valve on the nearest

frequently used drinking water line.

SHUT OFF THE MAIN WATER SUPPLY

Turn on the nearest faucet to relieve the

pressure on the line.

2 CHOOSE THE VALVE LOCATION

Choose a location for

the valve that is easily

accessible. It is best to connect into the side of a

vertical water pipe. When

it is necessary to connect into a horizontal water

pipe, make the connection to the top or side, rather than at the bottom, to avoid drawing off any sediment from the water pipe.

3 DRILL THE HOLE FOR THE VALVE

Drill a 1Ain. hole in

the water pipe using a sharp bit. Remove any burrs resulting from drilling the hole

in the pipe. Be careful not to allow water

to drain into the drill. Failure to drill a 1Ain.

hole may result in reduced ice production or smaller cubes.

_ NOTE ..................................

The hookup line cannot be white, plastic / tubing. Licensed plumbers must use I

only copper tubing NDA tubing #49595 I or 49599 or Cross Link Polyethylene I

]

INSTALLATION 21

FASTEN THE SHUTOFF VALVE 7 Fasten the shutoff valve to the cold water pipe with the pipe clamp,

Pipe Clamp_

Saddle-Type _" _ _Vertical Cold

Shutoff Valve _ I Water Pipe

Commonwealth of Massachusetts Plumbing Codes 248CMR shall be J

adhered to. Saddle valves are illegal and I

use is not permitted in Massachusetts,J 8 Consult with your licensed plumber. /

TIGHTEN THE PIPE CLAMP Tighten the clamp screws until the sealing

washer begins to swell.

NOTE: Do not overfighten clamp or

you may crush the tubing.

-- Washer

Clamp Screw

Pipe Clamp _,

_ Inlet End

ROUTE THE TUBING

Route the tubing between the cold water line and the refrigerator.

Route the tubing through a hole drilled in the wall or floor (behind the refrigerator or

adjacent base cabinet) as close to the wail as possible.

,-_ NOTE

Be sure there is sufficient extra tubing (about 8 feet coiled into 3 turns of

about 10 in. diameter) to allow the

refrigerator to move out from the watt

after installation.

CONNECT THE TUBING TO THE VALVE Place the compression nut and ferrule

(sleeve) for copper tubing onto the end of the tubing and connect it to the shutoff

valve, Make sure the tubing is fully inserted into the valve, Tighten the compression

nut securely,

Saddle-Type

Shutoff Valve __.

Packing Nu_ 1_

Outlet Valve _

Compression

\.... Ferrule (sleeve)

FLUSH OUT THE TUBING Turn the main water

supply on and flush out the tubing untit the water is clear.

Shut the water off at the water valve after about

one quart of water has been flushed through the tubing.

CONNECT THE TUBING TO THE

REFRIGERATOR

NOTE: Before making the connection to the refrigerator, be sure that the refrigerator power cord is not plugged into

the wall outlet.

a. Remove the plastic flexible cap from

the water valve.

b, Place the compression nut and ferrule

(sbeve) onto the end of the tubing as shown.

c. Insert the end of the copper tubing into

the connection as far as possible. While

holding the tubing, tighten the fitting.

Tubing Clamp /1-[_ ¼ in.Tubing

¼in. \ L_t / _/_

CotPression "X_ IllII/,.\ I

RefrigeratorConnection

22 INSTALLATION

10 TURN THE WATER ON AT THE SHUTOFF

VALVE Tighten any connections that leak,

I _ CAUTION

Checktoseeif/eaks occur at the water hneconnect_ons_

11 PLUG IN THE REFRIGERATOR

Arrange the coil of tubing so that it does not vibrate against the back of the refrigerator or against the wall, Push the

refrigerator back to the walt,

12 START THE ICEMAKER

Set the icemaker power switch to the ON position,

The icemaker will not begin to operate until it reaches its operating temperature

of 15°F (-9°C) or below. It wilt then begin operation automatically if the icemaker

power switch is in the ON (I} position.

Turning On The Power

1 Plug in the refrigerator,

(_Z_ CAUTION

• Connect to a rated power outlet. Have a certified electrician check

the wall outlet and wiring for proper grounding,

Do not damage or cut off the ground terminal of the power plug,

Leveling and Door Alignment

INSTALLATION 23

Leveling

After installing, plug the refrigerator's power

cord into a 3-prong grounded outlet and push

the refrigerator into the final position.

Your refrigerator has two front leveling legs--

one on the right and one on the left. Adjust the legs to alter the tilt from front-to-back or side-

to-side, tf your refrigerator seems unsteady, or you want the doors to close more easily, adjust the refrigerator's tilt using the instructions

below:

Remove the base grille. Refer to the Base Grille Installation section.

Turn the leveling leg to the left to raise that side of the refrigerator or to the right

to lower it. It may take several turns of the leveling leg to adjust the tilt of the

refrigerator.

Door Alignmenf

Both the left and right refrigerator doors have an adjustable nut, located on the bottom hinge,

to raise and lower them to align properly. If the space between your doors is uneven, follow the instructions below to align the doors

evenly: Use the wrench (included with the Owner's

Manual) to turn the nut in the door hinge to adjust the height. To the right to raise or to the

left to lower the height.

A flare nut wrench works best, but an open-end wrench will suffice.

NOTE 1

Do not over-tighten.

Open both doors again and check to make sure that they close easily. If the doors do

not close easily, tilt the refrigerator slightly more to the rear by turning both leveling

legs to the left. tt may take several more turns, and you should turn both leveling legs the same mount.

4 Replace the base grille.

24 HOW TO USE

HOW TO USE

Clean the refrigerator. Clean your refrigerator thoroughly and wipe off all dust that accumulated during

shipping.

]_z_ CAUTION

I' Do not scratch the refrigerator with a sharp object or use a detergent that

contains alcohol, a flammable liquid or an abrasive when removing any tape or adhesive from the refrigerator,.

I" Do not peel off the model or serial number label or the technical information t on the rear surface of the refrigerator.

Remove adhesive residue by wiping it off with your thumb or dish detergent.

Connect the power supply. Check if the power supply is connected before use.

Read the "Turning On The Power" section.

Turn off the icemaker if the refrigerator is not yet connected to the water supply.

Turn off the automatic icemaker and then plug the power plug of the refrigerator into the grounded electric outlet.

* This is applicable only to certain models.

unning the automatic icemaker before connecting it to the water

{_ CAUTION }

supply may cause the refrigerator to malfunction,

Waif for the refrigerator to cool. Allow your refrigerator to run for at least two to three hours before putting food in it. Check the flow of cold air in the freezer compartment to ensure proper cooling.

utting food in the refrigerator before it has cooled could cause the

-_ CAUTION 1 food to spoil, or a bad odor could remain inside the refrigerator.

The refrigerator makes a Joud noise after initial operation. This is normal. The loudness will decrease as the temperature lowers.

Open refrigerator doors and freezer drawers to ventilate the inferior. The inside of the refrigerator may smell like plastic at first. Remove any adhesive

tape from inside the refrigerator and open the refrigerator doors and the freezer drawers for ventilation.

HOW TO USE 25

Confrol Panel

* Depending on the model, some of the following functions may not be available.

Confrol Panel F'eafures

The LED Display shows the temperature settings, dispenser options, water filter, door alarm, and

locking status messages.

Ice Type

Press the ICE TYPE button to seiect either Crushed or Cubed Ice. The selected option will illuminate on the LED display.

Freezer L'7OF

LED Display

Control Buttons

Press the FREEZER button to adjust the temperature in the freezer compartment.

NOTE

o change thedisplayfromFahrenheitto

elsius,pressand holdthe FREEZER and

Refrigerator ==_ i F

--#--I o

Press the REFRIGERATOR button to adjust the temperature in the freezer compartment.

Ice Plus

This function increases both ice making and freezing capabilities.

• When you touch the Ice Plus button, the graphic will illuminate in the display and

will continue for 24 hours. The function will automatically shut off after 24 hours.

• You can stop this function manually by touching the button one more time.

26 HOW TO USE

Control Panel F'eafures (continued)

Fresh Air Filter

The Fresh Air Filter helps remove odors from the refrigerator. The Fresh Air Filter has two settings,

Auto and Power(PWR). In Auto mode, the Fresh Air Filter will cycle on and off in increments of ten

minutes on and one hundred ten minutes off. If set to the Power(PWR) mode, the Fresh Air Filter

will stay on continuously for four hours, cycling on and off in increments of ten minutes on and five

minutes off. After four hours, the Fresh Air Filter wilt switch back to Auto mode.

Auto mode is the default mode.

• The Press the Air Filter button once for Power(PWR) mode.

. Press the Air Filter button again to switch

back to Auto mode.

Light --O-- Press the LIGHT button, to turn on the

dispenser light. The indicator will appear on the LED display.

Change Filter _

When the water filter indicator turns on, you have to change the water filter. After changing the water filter, press and hotd the FILTER

button for three seconds to turn the indicator light off. You need to change the water filter

approximately every six months.

Alarm

Control Lock

The Control Lock function disables every other button on the display.

When power is initially connected to the

refrigerator, the Lock function is off. tf you want to activate the Lock function to

lock other buttons, press and hold the Lock button for three seconds or more. The Lock

icon wilt display and the Lock function is now enabled.

- To disable the Lock function, press and hold the Lock button for approximately three seconds.

--_ CAUTION Display Mode (For Store Use Only)

The Display Mode disables all cooling

in the refrigerator and freezer sections

to conserve energy while on display in a retail store. When activated, OFF will

display on the control panel.

To deactivate: With either refrigerator door opened,

press and hold the Refrigerator and

Ice Plus buttons at the same time for

five seconds. The control panel will beep and the temperature settings witl display to confirm that Display Mode is deactivated. Use the same procedure

to activate the Display Mode.

, When power is connected to the

refrigerator, the door alarm is initially set to ON. When you press the ALARM button,

the display witl change to OFF and the Alarm function wilt deactivate.

, When either the refrigerator or the freezer

door is left open for more than 60 seconds, the alarm tone wilt sound to let you know

that the door is open.

. When you close the door, the door alarm

will stop.

in-Door Ice Bin

HOW TO USE 27

× Depending on the model, some of the

following functions may not be available.

'_"2_ CAUTION

, Keep hands and tools out of the ice

compartment door and dispenser chute. Failure to do so may result in damage or

personal injury.

. The icemaker will stop producing ice when

the in-door ice bin is full. If you need more ice, empty the ice bin into the extra ice bin in the freezer compartment. During use,

the ice can become uneven causing the icemaker to misread the amount of ice

cubes and stop producing ice. Shaking the ice bin to level the ice within it can reduce

this problem.

. Storing cans or other items in the ice bin will

damage the icemaker.

• Keep the ice compartment door closed tightly. If the ice compartment door is not

closed tightly, the cold air in the ice bin will freeze food in the refrigerator compartment.

This could also cause the icemaker to stop producing ice.

. If the ON/OFF switch on the icemaker is

set to OFF for an extended period of time, the ice compartment will gradually warm

up to the temperature of the refrigerator compartment. To prevent ice cubes from

melting and leaking from the dispenser, ALWAYS empty the ice bin when the

icemaker is set to OFF for more than a few hours.

2 To remove the in-door ice bin, grip the

front handle, slightly lift the lower part, and slowly pull out the bin as shown.

Assembling the In-Door ice Bin

1 Carefully insert the in-door ice bin while

slightly slanting it to avoid contact with the icemaker.

2 Avoid touching the ice-detecting sensor

when replacing the ice bin. See the label on the ice compartment door for details.

Defaching the In-Door Ice Bin

1 Gently pull the handle to open the ice

compartment.

i[_ CAUTION

en handlingthe icebin,

eep hands away from the

emaker trayareatoavoid

ersonal injury.

X,.__j

28 HOW TO USE

Automatic Icemaker

Depending on the model, some of the

following functions may not be available.

Ice is made in the automatic icemaker and sent to fhedispenser The icemaker will

produce 70-210 cubes in a 24-hour period,

depending on freezer compartment temperature,

room temperature, number of door openings and

other operating conditions.

* It fakes about 12 to 24 hours for a newly

installed refrigerator to begin making ice. Wait 72 hours for full ice production to occur

o Ice making stops when the in-door ice bin is fuji

When full, the in-door ice bin holds approximately 6 to 8 (12-16 oz or 340-455 cc) glasses of ice

° The water pressure must be between 20 and 120

psi (140 and 830 kPa)on models without a water filter and between 40 and 120 psi (280 and 830

kPa) on models with a wafer filter to produce the normal amount and size of ice cubes

* Foreign substances or frost on the ice-detecting

sensor can interrupt ice production Make sure the sensor area is clean af all times

for proper operation

Wafer fills the ice fray.

1 hour later from supplying wafer

* 60 minutes after water has been added

fo the ice tray, the ice tray wilI sit slightly filled to help the cold air reach the ice.

Switch

ice-defecting

Icemaker

Sensor

* The ice-detecting sensors will sense

when the ice is ready to be dumped

into the ice bin

Turning the Automatic Icekarner On or Off

To turn off the automatic icemaker, set the icemaker switch to OFF (O) To turn on the automatic icemaker, set the switch fo ON (I).

HOWTOUSE29

Automatic Icemaker

(continued)

Fz_ CAUTION

o The first ice and water dispensed may

include particles or odor from the water supply line or the water tanL

• Throw away the first few batches of ice (about 24 cubes). This is also necessary if

the refrigerator has not been used for a long time.

= Never store beverage cans or other items in

the ice bin for the purpose of rapid cooling.

Doing so may damage the icemaker or the

containers may burst.

= tf discolored ice is dispensed, check the

water filter and water supply. If the problem continues, contact a Sears or other qualified

service center. Do not use the ice or water until the problem is corrected.

• Keep children away from the dispenser. Children may play with or damage the

controls.

• The ice passage may become blocked with

frost if only crushed ice is used. Remove the frost that accumulates by removing the ice

bin and clearing the passage with a rubber spatula. Dispensing cubed ice can also help

prevent frost buildup.

= Never use thin crystal glass or crockery to

collect ice. Such containers may chip or

break resulting in glass fragments in the ice.

= Dispense ice into a glass before filling it

with water or other beverages. Splashing

may occur if ice is dispensed into a glass

that already contains liquid.

Never use a glass that is exceptionally narrow or deep. Ice may jam in the ice

passage and refrigerator performance may be affected.

Keep the glass at a proper distance from

the ice outlet. A glass held too close to the outlet may prevent ice from dispensing.

• To avoid personal injury, keep hands out of

the ice door and passage.

= Never remove the dispenser cover.

tf ice or water dispenses unexpectedly, turn

off the water supply and contact a qualified

service center.

When You Should Turn the

lcemaker Off

• When the water supply will be shut off for several hours.

When the ice bin is removed for more than one or two minutes.

• When the refrigerator witl not be used for several days.

@NOTE /

he ice bin should be emptied when the

cemaker on!off switch is turned to the

OFF position.

Normal Sounds You May Hear

= The icemaker water valve will buzz as

the icemaker fills with water, tf the

power switch is in the ON (I) position, it will buzz even if it has not yet been

hooked up to water. To stop the buzzing, move the power switch to OFF (0).

Keeping the power switch in the ON (I) position before the water line is connected can damage the icemaker.

° You will hear the sound of cubes

dropping into the bin and water running

in the pipes as the icemaker refills.

Preparing for Vacation

Set the icemaker power switch to OFF (0) and shut off the water supply to the refrigerator,

'T( _ NOTE

he icebinshouldbe emptied anytime

he ieemakeron/offswitchisturnedto

the OFF (0) position. ._

if the ambient temperature will drop below

freezing, have a qualified technician drain the water supply system to prevent serious

property damage due to flooding caused by ruptured water lines or connections.

30 HOW TO USE

Ice and Wafer Dispenser

* Depending on the model, some of the

following functions may not be available.

I K_'w CAUTION "/

eep children away from the dispenser.

Children may play with or damage the controls.

Dispenser

Water Switch

ice Switch

Stand

Using the Dispenser

* To dispense cold water, push on the

water switch with a glass.

- To dispense ice, push on the ice switch with a glass.

InoorreotWayc0rrectWay

Water

Ice

-_ CAUTION hrow away the first few batches of ice

about 24 cubes). This is also necessary

f the refrigerator has not been used for

long time

Locking fhe Dispenser

Press and hold the Alarm and Lock button

simultainously for 3 seconds to lock the dispenser and all the controt panel functions. Follow the same instructions to unlock.

- _ NOTE . If discolored ice is dispensed, check

the water filter and water supply. If the

problem continues, contact a qualified service center. Do not use the ice or

water until the problem is corrected.

* The dispenser will not operate when

either of the refrigerator doors are open.

. If dispensing water or ice into a container

with a smalt opening, place it as close to the dispenser as possible.

Some dripping may occur after dispensing. Hold your cup beneath

the dispenser for a few seconds after

dispensing to catch all of the drops.

Cleaning fhe Dispenser Sfand

1 Grip the stand with both hands and pull it

out.

2 Wipe out dirty areas with a clean cloth.

+ 142 hidden pages