Updated the Table2-1, Table2-2, Table96, 7, 16Jul. 11. 20050.2
Updated the Table7, Updated the Safety14, 25Jul. 28. 20051.0
Changed the Suffix name (STC1 Æ STC2)-Sep. 21. 20052.0
Changed the Table 3 (Deleted HDCP Function)8
Changed the Table 9 (Contrast Ratio : 800 Æ 700)16
Updated the LCM Drawing (Changed the suffix name)23
www.jxlcd.com
www.jxlcd.com
Ver. 2.0Sep. 21 . 2005
3/ 28
LM230WU3
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
Liquid Crystal Display
Product Specification
1. General Description
The LM230WU3 LCD is a Color Active Matrix Liquid Crystal Display with an integral Cold Cathode Fluorescent
Lamp(CCFL) back light system. The matrix employs a-Si Thin Film Transistor as the active element. It is a
transmissive type display operating in the normally black mode. This TFT-LCD has a 23.0 inch diagonally
measured active display area with WUXGA resolution(1200 vertical by 1920 horizontal pixel array). Each pixel
is divided into Red, Green and Blue sub-pixels or dots which are arranged in vertical stripes. Gray scale or
the luminance of the sub-pixel color is determined with a 8-bit gray scale signal for each dot, thus, presenting
a palette of more than 16,777,216 colors.
The LM230W02 has been designed to apply the TMDS
Hard coating(3H), Anti-glare treatment of the front polarizerSurface Treatment
Ver. 2.0Sep. 21 . 2005
(5 points Avg.)Luminance, White
@VLCD, 53 Watt @400cd)Power Consumption
4/ 28
LM230WU3
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
Liquid Crystal Display
Product Specification
2. Absolute Maximum Ratings
The following are maximum values which, if exceeded, may cause faulty operation or damage to the unit.
Table 1. ABSOLUTE MAXIMUM RATINGS
ParameterNotes
Power Input Voltage
Operating Temperature
Storage Temperature
Operating Ambient Humidity
Storage Humidity
Note : 1. Temperature and relative humidity range are shown in the figure below.
Wet bulb temperature should be 39 °C Max, and no condensation of water.
www.jxlcd.com
www.jxlcd.com
Wet Bulb
Temperature [C]
10
0
Symbol
50
40
30
20
Values
MaxMin
500TOP
60-20TST
90%
60
60%
40%
Humidity [(%)RH]
10%
Units
Vdc21-0.3VLCD
°C
°C
%RH9010HOP
%RH9010HST
at 25 ± 2°C
1
Storage
Operation
10203040506070800-20
Dry Bulb Temperature [C]
Ver. 2.0Sep. 21 . 2005
5/ 28
LM230WU3
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
Liquid Crystal Display
Product Specification
3. Electrical Specifications
3-1. Electrical Characteristics
It requires two power inputs. One is employed to power the LCD electronics and to drive the TFT array and
liquid crystal. The second input power for the CCFL, is typically generated by an inverter. The inverter is an
external unit to the LCDs.
Table 2-1. ELECTRICAL CHARACTERISTICS
ParameterSymbol
MODULE :
ILCDPower Supply Input Current
Note :
1. The specified current and power consumption are under the V
whereas mosaic pattern(8 x 6) is displayed and f
2. The current is specified at the maximum current pattern.
3. The duration of rush current is about 2ms and rising time of power Input is 1ms(min.).
www.jxlcd.com
www.jxlcd.com
White : 255Gray
Black : 0Gray
is the frame frequency.
V
Values
MaxTypMin
=18.0V, 25 ± 2°C,fV=60Hz condition
LCD
Maximum current pattern
Vdc19.018.017.0VLCDPower Supply Input Voltage
mVp-p400VdRFPermissive Power Input Ripple
NotesUnit
1mA520450-
2mA675585-
1Watt9.48.1-PLCDPower Consumption
3A3.0--IRUSHRush current
Mosaic Pattern(8 x 6)
Ver. 2.0Sep. 21 . 2005
White Pattern
6/ 28
Product Specification
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
Table 2-2. INVERTER ELECTRICAL CHARACTERISTICS
ConditionSymbolParameter
Inverter :
Values
LM230WU3
Liquid Crystal Display
Unit
Max.Typ.Min.
Notes
Input Voltage
Input Current
LAMP :
Notes :
1. The input voltage ripple is limited below 400mVp-p.
2.The specified current and power consumption are under the typical supply Input voltage, 24V.
3.The life is determined as the time at which luminance of the lamp is 50% compared to that of initial
value at the typical lamp current on condition of continuous operating at 25 ± 2°C.
4. Electrical characteristics are determined after the unit has been ‘ON’ and stable for approximately
30min in a dark environment at 25 °C± 2°C.
www.jxlcd.com
www.jxlcd.com
ON/OFFB/L on/off control
DDB
DDB
BRBrightness Adj
BR
BR
= 3.3VI
= 3.3VPBInput Power
V26.424.021.6V
A2.552.21.85V
Watt585348V
V5.0-2.0Lamp ON = HighV
V0.8-0.0Lamp OFF =Low
V3.3-0V
1
2
2
3Hrs50,000Life time
Ver. 2.0Sep. 21 . 2005
7/ 28
LM230WU3
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
Liquid Crystal Display
Product Specification
3-2. Interface Connections
This LCD employs Two interface connections, a 30 pin connector is used for the module electronics and a
14Pin Connector is used for the integral backlight system.
3-2-1. LCD Module
- LCD Connector(CN1) : IS100-L30B-C23 (UJU), FI-XB30SSL-HF15 (JAE) or Equivalent
- Mating Connector : FI-X30C2L (Manufactured by JAE) or Equivalent
Table 3 MODULE CONNECTOR(CN1) PIN CONFIGURATION
SymbolNo
GND1
SHLD22
RX2+3
RX2-4
SHLD15
RX1+6
RX1-7
SHLD08
RX0+9
RX0-10
SHLDC11
RXC+12
RXC-13
GND14
Ground
Shield for TMDS channel 2
TMDS Differential Output(+) (CH 2)
TMDS Differential Output(-) (CH 2)
Shield for TMDS channel 1
TMDS Differential Output(+) (CH 1)
TMDS Differential Output(-) (CH 1)
Shield for TMDS channel 0
www.jxlcd.com
www.jxlcd.com
TMDS Differential Output(+) (CH 0)
TMDS Differential Output(-) (CH 0)
Shield for TMDS channel C
TMDS Differential Output(+) (CH C)
TMDS Differential Output(-) (CH C)
Ground
Description
No
16
17
18
19
20
21
22
23
24
25
26
27
28
29
Symbol
OPEN
OPEN
OPEN
GND
GND
GND
V
LCD
V
LCD
V
LCD
PWR_ON
HS_OUT
VS_OUT
GND
OPEN
Symbol
NC
NC
NC
Ground
Ground
Ground
Supply voltage for LCD
Supply voltage for LCD
Supply voltage for LCD
Power ON control signal input
3.3V(H:90%,L:10%)
Hsync Output
Vsync Output
Ground
DDC –Clk(HDCP) for future use
OPEN15
HDCP VCC (3.3V) for future use
30
OPEN
DDC –Data(HDCP) for future use
Notes: 1. All GND(ground) pins should be connected together and should also be connected to the LCD’s
metal frame.
2. All V
(power input) pins should be connected together.
LCD
3. Input Level of TMDS signal is based on the Digital Visual Interface (DVI 1.0) Standard.
Rear view of LCM
1
Ver. 2.0Sep. 21 . 2005
30
IS100-L30B-C23(UJU)
8/ 28
Liquid Crystal Display
www.DataSheet.co.kr
Datasheet pdf - http://www.DataSheet4U.net/
Product Specification
3-2-2. Backlight Interface
- Inverter Connector : S14B-PHA-SM3 Side entry type (Manufactured by JST) or Equivalent
- Mating Connector : PHR-14(Manufactured by JST) or Equivalent
Table 4. INVERTER CONNECTOR PIN CONFIGULATION
LM230WU3
RemarksDescriptionSymbolPin No
BL1
BL2
BL3
BL4
BL5
www.jxlcd.com
ON12
www.jxlcd.com
BR13
Notes : 1. GND is connected to the LCD’s metal frame.
Power Supply +24.0VV
Power Supply +24.0VV
Power Supply +24.0VV
Power Supply +24.0VV
Power Supply +24.0VV
Power GroundGND6
Power GroundGND7
Power GroundGND9
Power GroundGND10
NCOPEN11
Backlight On/off SignalV
Lamp Operating StatusStatus14
Note 1Power GroundGND8
(On :2.0V~5V/Off :0.0~0.8V)
(Max :3.3V / Min :0.0V)Brightness Adjustable VoltageV
Normal=0~0.8V
Abnormal=3.0~5.0V
Rear view of LCM
PCB
14
…
1
S14B-PHA-SM3-TB
(JST : Japan Solderless Terminal Co.,Ltd.)
Ver. 2.0Sep. 21 . 2005
…
9/ 28
Loading...
+ 19 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.