LG LE6016N-NH Owner’s Manual

OWNER’S MANUAL

Digital Video Recorder

Please read this manual carefully before operating your set and retain it for future reference.

MODEL

LE6016N LE6016D

P/NO : COV30400919 1105(V1.5)

Safety Information

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning ash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sucient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modications to this equipment may cause harmful interference unless the modications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modication is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection

against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

• A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user.

• Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

• Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.

This Class A digital apparatus complies with Canadian ICES-003. Cet appareil numérique de la classe A est conforme à la norme NMB-003 du Canada.

Warning: Do not install this equipment in a conned space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Safety Information

Warning: To reduce a risk of re or electric shock, do not expose this product to rain or moisture.

Caution: This installation should be made by a qualied service person and should conform to all local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualied personnel only.

Caution: The apparatus should not be exposed to water (dripping or splashing) and no objects lled with liquids, such as vases, should be placed on the apparatus.

Caution:

This product employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center. Performing controls, adjustments, or carrying out procedures other than those specied herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.

To disconnect power from mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

LG Electronics hereby declares that this/these product(s) is/are in compliance with the essential requirements and other relevant provisions of Directive 2004/108/ EC, 2006/95/EC, and 2009/125/EC.

European representative :

LG Electronics Service Europe B.V. Veluwezoom 15, 1327 AE Almere. The Netherlands (Tel : +31-(0)36-547-8888)

Disposal of your old appliance

When this crossed-out wheeled

bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

All electrical and electronic

products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

The correct disposal of

your old appliance will help prevent potential negative consequences for the environment and human health.

For more detailed information

about disposal of your old appliance, please contact your city oce, waste disposal service or the shop where you purchased the product.

EEE Compliance with Directive. (for Turkey only)

Safety Information

4 Safety Information

IMPORTANT SAFETY INSTRUCTIONS

Safety Information

Read these instructions.

Keep these instructions.

Heed all warnings.

Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in

accordance with the manufacturer’s instructions.

Do not install near any heat sources such

as radiators, heat registers, stoves, or other apparatus (including ampliers) that produce heat.

Do not defeat the safety purpose of the

polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not t into your outlet, consult an electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on

10.

or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

Only use attachments/accessories specied by

11.

the manufacturer.

Use only with the cart, stand, tripod, bracket, or

12.

table specied by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

Unplug this apparatus during lightning storms

13.

or when unused for long periods of time.

Refer all servicing to qualied service personnel.

14.

Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

5Safety Information

Please follow the directions safely use the product

The purpose of the following safety precaution is to prevent any unexpected risk or damage by using the product accurately as intended.

Warning

• Turn o the power of the product before installing the product. Do not plug many plugs into one outlet.

- It can cause an electric shock or a re.

• Do not put any containers with liquid such as water, coee, beverage etc. on top of the product.

- It can cause a re, an electric shock or a product problem.

• Do not put any heavy object on top of the cable or excessively bend the cable.

- It can cause a re.

• When wiping the surface of the product, do not use water, chemical or detergent, and always use a dry towel.

- It can cause an electric shock, problems or scratches to the surface of the product.

• Do not install the product where the level of humidity, dust or smoke is high.

- It can cause an electric shock or a re

• When unplugging the power, hold the plug and unplug slowly. Do not hold the plug with wet hands or plug to a loose power outlet.

- It can cause an electric shock or a re.

• Do not disassemble or recongure the product. Because high level of current ows on the device, it is dangerous to do so.

- It can cause a re, an electric shock or an injury.

• Always check for dangerous elements where the product is installed. If dangerous elements (Moisture, damaged cable, unstable installation etc.) are identied, please contact your nearest service center.

- It can cause an electric shock or a re.

• Because the cable connected to this device can be damaged, keep at least 15cm of clearance between where the product is installed and where the power outlet is.

- It can cause a re, an electric shock or an injury.

• Install the product in a cool location not exposed to direct sunlight. Do not install the product where trac is high or near the heating devices.

- It can cause a re.

• Install the product on a location with a at surface where it is ventilated well and not too high.

- It can cause a problem or an injury.

• The power outlet must be grounded and the voltage range must bet within 10% of the rated voltage. Do not share the power outlet with hair dryer, iron, refrigerator or heating device etc.

- It can cause an explosion.

• When replacing the battery, always replace with the same type of battery as the one provided. When disposing the battery, follow the direction of the manufacturer.

- It can cause an explosion.

Safety Information

6 Safety Information

• For old hard drives, you may not be able to recover the data stored on the drive. When you use a damaged hard drive, you will see a sign on the screen saying “Error or

Safety Information

defective”. For the old hard drive, contact your nearest service center or the original retailer to replace the hard drive.

- LG Electronics is not responsible for the data loss from misuse by the user.

Any changes or modications in construction of this device which are not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Caution

Please read the following precautions carefully before installing the product and follow the directions for installation.

• Do not install the product where the level of humidity, dust or smoke is high.

• Do not install the product where it is exposed to direct sunlight or close to the heating device.

• Do not install the product where there is danger of electric shock or near magnetic object.

• Do not put objects with high conductivity on top of the ventilation outlet of the product.

• Make sure the power is turned o before installing the product.

• Secure sucient space to connect the product when installing the product.

• Do not install the product where it is not at, not ventilated well or where vibration is severe.

• When you install the product near electronic appliances such as radio or TV, it can cause problems to the product.

• Do not disassemble the product unless done by a technician certied by LG Electronics.

• Do not put heavy objects on top of the product.

• Be careful not to let alien particles get inside the product.

- It can cause a problem to the product.

• Install the product where it is ventilated well.

- The product at least 15 cm away from the wall power outlet because the cable can be damaged.

• Do not install the product at a location close to a product or broadcast receiver with strong electric or magnetic wave.

• Do not put heavy objects on top of the product.

- It can cause a problem to the product.

• Install the product at a at and stable location.

- The product may not operate normally.

• The product at a location with appropriate level of temperature and humidity.

- Do not install the product where the temperature is too high (40 °C or above) or too low (0° or less).

• Because the vibration and impact can damage the product, do not throw any objects to the location where the product is installed.

• Do not install the product where it is exposed to direct sunlight or close to the heating device.

• Firmly xate the product at a location where it is well ventilated.

- It can cause problems to the product depending on the surrounding environment. It is recommended to use the Automatic Voltage Regulator. It is recommended to wrap wires around the Ferrite core.

• The power outlet must be grounded.

• If you hear any noise or smell any odor from the product, turn the product o and contact your nearest service center.

- It can cause a re or an electric shock.

• Periodically have the product checked by the service center to safety use the product

- When replacing the battery, always replace with the same type of battery as the one provided. When disposing the battery, follow the direction of the manufacturer.

- LG Electronics is not responsible for the problem from misuse by the user

• Do not move or ip the product over while using the product.

7Safety Information

Safety Information

Contents

Safety Information

4 IMPORTANT SAFETY

INSTRUCTIONS

5 Please follow the directions

safely use the product

Before use

10 2-1. Product characteristics

15 2-6. Connection and initial

setting

16 RS-485 connection

16 Control port (Output)

connection

17 Sensor (Input) connection

17 About internal hard disk

18 Hard disk installation or

replacement

Functional description

22 3-1. Operation

22 Start Up

23 Shutdown

24 3-2. Monitor Screen

11 2-2. Components

11 2-3. Front side

11 LE6016D model

12 LE6016N model

13 2-4. Rear side

14 2-5. Remote Controller

14 How to set the id of remote

controller

28 3-3. System Setting

28 System

33 Camera

38 Event

42 Network

46 Information

49 3-4. PTZ Control

51 3-5. Search (Playback) &

Backup

51 Time search

52 Event Search

54 Backup

Web viewer

58 4-1. Installation

58 Web viewer installation

60 4-2. Functional description

60 Web viewer monitoring

window

61 Web viewer search window

62 Search dialog box

63 Saving as AVI ﬁle dialog

box

service

70 6-2. Recommended device to

use

70 List of recommended USB

memory

71 Recommended list of CD/

DVD media

72 List of supported PTZ

camera

73 6-3. Initial setting list for factory

default

80 6-4. Product speciﬁcation

Apple iPhone/iPod

64 5-1. Functional description

64 Real-time monitoring

Reference

66 6-1. Check before requesting for

10 Before use

2 Before use

2-1. Product characteristics

Before use

• Adopted the stable Embedded Linux

• Stable le system recovery even after power supply is disconnected from a power outage.

• Realized small le size and high video quality by applying the H.264.

• Supports terra byte hard disk (up to 1TB )

• Supports E-SATA port to use additional external hard disk.

• Real time recording

- Maximum of 480 IPS@352 X 240 at NTSC

- Maximum of 400 IPS@352 X 288 at PAL

• Supports various recording resolutions and qualities.

- D1(720x480), Half D1(720x240), CIF(352x240) at NTSC

- D1(720x576), Half D1(720x288), CIF(352x288) at PAL

- 5 stage recording qualities (Very high, high, normal, low, very low).

• Easy operation through various user interface and user friendly GUI system.

• Realized powerful multi-function.

- Real time video display or recording, network transmission and back up can be performed simultaneously

• Easy search functions.

- Date/Time search (Calendar search), event search

• Recording before event. (Can be 2~4 seconds).

• Recording after event. (Can be only up 10 seconds).

• The operating condition pre-check function according to the change in motion detection and movement detection

• Can set recording quality and number of recording frames per seconds.

• Powerful recording schedule management.

• Complete synchronization of video/audio.

• Easy software upgrading through USB storage device or network.

• Maximum of 5 clients can be connected to 1 DVR at the same time.

• Band width setting is automatically set depending on the network speed connected to this device.

• Remote alarm notication via e-Mail.

• PTZ (Pan/Tilt/Zoom) operation.

• Remote control operation

• Key board control operation (optional)

• Supporting Daylight saving

• Simultaneous output to VGA and BNC

2-2. Components

Installation CD Owner’s Manual Power cable

Mouse Remote control Adapter

11Before use

Before use

SATA cable

Reference: The type of components can be applied dierently by the option.

HDD power cable

2-3. Front side

LE6016D model

a b c d

f g

Screws

12 Before use

LE6016N model

There is no built-in DVD recorder at LE6016N model.

Before use

f g

a DVD Recorder: This is used for DVD backup.

b LED

• Hard disk LED: This is turned on HDD is accessed.

• Power LED: This is turned on when the power is turned on.

• Network LED: This is turned on when network is connected.

• Alarm LED: This is turned on when alarm event occurs.

c Navigation buttons

• At power o status, it is turned on by pressing “OK” button in some seconds.

• At power on status, instant panic recording is executed by pressing “OK” button in some seconds.

• “SEARCH/LIVE” button is used as navigation key, when menu is shown, on the Chapter 1 Before use other hand, it is used for switching key between SEARCH and LIVE screen when menu not be shown.

d MENU/ESC: This is used to open or close menu.

e OPEN: This is used to open or close the door of DVD recorder.

f MOUSE: This is used to connect mouse.

g USB: This is used to connect USB external device.

b c d

CAUTION

Mouse should be connected to front side mouse port.

2-4. Rear side

b c d

e f g h i j k

a Main output port: It is used to connect BNC type monitor. (It outputs the same video as

MAIN output.)

b Camera video input: These are used to connect cameras.

c External HDD port: It is used to connect E-SATA HDD.

d Sensor/Alarm/RS-485 ports - These are used to connect sensor, alarm and RS-485 serial

communication port.

e USB port: It is used to connect the USB external device.

f Ethernet port - It is used to connect RJ-45 Ethernet connector. (LAN PORT).

g VGA port: It is used to connect VGA monitor.

h Audio input port - It is used to connect audio output port of external device.

i Audio output port - It is used to connect audio input port of external device.

j SPOT output port - It is used to connect BNC type monitor.

k Power connector - It is used to connect Power adapter.

13Before use

Before use

14 Before use

2-5. Remote Controller

No. Function Description

Before use

f h

l n

Reference: The shape of remote controller can be dierent by the model.

e g i

m o

c d e f g h i

Power This is used to turn on/o the power.

Emergency

recording

Number keys This is used to input channel or values.

Plus(+) This is used to increase setting values.

Minus(-) This is used to decrease setting values.

CANCEL This is used to cancel a job.

LIVE This is used to display real time screen.

MENU This is used to display menu.

SEARCH This is used to display screen search.

j wsad

Play buttons

PTZ Menu This is used to open PTZ Menu.

Export backup

Split screen This is used for split screen display.

Auto switching

This is used to start/stop emergency recording.

This is used to navigate each menu

, OK

item.

These are used to control playback (Backward or forward search, play and pause)

and buttons have no

function.

This is used to run backup.

It can be run in search mode.

This is used to display channel one by one.

It works as event search at search

mode.

How to set the id of remote controller

1. Press CANCEL button about 3 seconds then light of power button turns on.

2. Enter two digit numbers which is the id of remote controller using number keys.

You have to input ‘0’ rst when you are to input one digit number.

Ex) In case you want to use ‘2’ as ID, input ‘02’.

3. Every time you press the number key the light of power button will blink.

4. Stopping blinking means that the id is saved.

2-6. Connection and initial setting

Caution

• The camera or other external devices can be connected to this device in numerous methods. Refer to the user manual of the camera or other external device for addition information on connection methods.

• When installing the camera, check whether the power of the camera is turned o.

• After installing the monitor, turn on the power of the DVR.

Connect the BNC type monitor. (The same video output as VGA.)

Connect the camera for coaxial connection.

15Before use

Before use

Connect the network cable.

Connect USB device.

Connect the power adapter.

Connect the BNC type monitor. (SPOT output)

Connect E-SATA HDD.

Connect the speaker or amplier.

Connect the audio. (Line input)

Connect VGA monitor.

16 Before use

RS-485 connection

①

This device has 1 data port (RS-485).

②

Use this port to connect the PTZ camera or the

keypad. (Optional)

③

PTZ camera / keyboard connection

i. Connect the PTZ serial communication cable to

Before use

the RS-485 port.

ii. When connecting the cable, make sure that

the TX- of the device is connected to the RX(TX-) of the camera(keyboard), and TX+ of the device is connected to the RX+(TX+) of the PTZ camera(keyboard).

iii. Recommended initial data setting is 9 600 baud

rate, 8 data bits, 1 stop bit and no parity.

iv. When connecting the PTZ camera or keyboard, always change the setting of the DVR

setting menu according the RS-485 setting of the camera, keyboard and this device.

v. Set the same baud rate when you are to use PTZ camera and keyboard at the same time

Control port (Output) connection

①



For interface and auto control with the external sensor, the interfacing control output port (Set value from “Setup Ò Event Ò Sensor/Motion/Video loss” menu) and the “RELAY” port are connected.

②

If the control device (Alarm light, amplied siren, external relay etc.) is “NC (Normal Close)” type,

connect to the control output NC (Normal Close) port.

③

If the control device (Alarm light, amplied siren, external relay etc.) is “NO (Normal Open)” type,

connect to the control output NO (Normal Open) port.

Sensor (Input) connection

Connect one of the signal cables (2 cables) of various sensors (IR sensor, heat ray detector, magnetic etc.) to the COM port and connect the remaining signal cable to the sensor number you want. (Sensor “NC, NO” type can be set from “Setup Ò Event Ò Sensor” menu.)

NOTE

NC and NO cannot be selected simultaneously.

About internal hard disk

1 Sensor input 1

2 Sensor input 2

3 Sensor input 3

4 Sensor input 4

G Ground

5 Sensor input 5

6 Sensor input 6

7 Sensor input 7

8 Sensor input 8

G Ground

17Before use

Before use

The hard disk installed inside the device is a precision device which can be damaged even with the small impact. To prevent the hard disk from being damaged, manage the device as follows. To prevent the data loss, it is recommended to back up any important data into an external storage device. When installing or uninstalling the hard disk, you must always turn o the power of the product.

• If the power is turned on, do not move the device.

• Do not install this device where it is too hot and humid and where the temperature change is sudden. It can cause a problem to the device.

• DO NOT pull out the plug or intercept the power supply while this device’s power is on.

• When there is a power outage while the power is turned on, some data can be lost.

• Do not drop the hard drive or put any metallic object, such as coins, inside the device.

• In case of a power outage while recording, avoid adding, replacing or moving the HDD. The recorded data can be lost. In this case, turn on the power with the original hard disk that was used while the power outage occurred. And then add, replace or move the HDD.

• Because the hard disk is a high precision device, the parts inside the disk can be damaged at the slightest impact. Please read the following precautions in detail and follow the directions.

- Do not directly put the hard disk on the desk or table. Because the parts inside the hard disk can be damaged at the slightest impact, put a thick cushion below the hard disk.

- If you use the motored driver, the parts inside the hard disk can be damaged from the vibration.

- When replacing the hard disk, be careful not to cause any impact to the other parts.

18 Before use

- Be careful not to cause an impact from the tools and hard disk used for the installation.

• Protect the hard disk from static electricity.

CAUTION

This device has elements to cause an electric shock, an accident or a problem to the product. Also the hard disk may not be recognized or operated properly due to incorrect installation and setting. Therefore consult with an experienced expert technician when installing the hard disk.

Before use

Hard disk installation or replacement

Hard disk installation

After turning on the power of the device, unplug the power from the outlet.

1. Loosen the screw on the left, right and rear side of the product.

2. Separate the cover of the main unit.

3. Remove the screws on the bracket holding the hard disk, separate the bracket from the hard disk.

4. Install the hard disk to the bracket and tighten the 4 screws.

Connecting bracket to hard disk

Set the SATA cable connection port to lower direction to install the hard disk to the bracket.

Connect the bracket to hard disk by tighten the 4 screws.

5. After installing the bracket on the main unit, tighten the screws.

6. Connect the power cable of the hard disk.

7. Connect the SATA cable to the hard disk.

8. Connect the SATA cable to the SATA port of the main board.

9. Close the cover of the main unit.

10. Tighten the screws.

11. After installing the hard disk, you must format the hard disk from the setting menu.

19Before use

Before use

- The rst SATA cable port on the main board must be connected at all times. If a hard disk is not connected, this device may not operate normally.

Hard disk replacement

First turn o the power of the device and then unplug the power.

1. Loosen the screw on the left, right and rear side of the product.

2. Separate the cover of the main unit.

20 Before use

3. After removing all of power/SATA cable connected to hard disk, please separate hard disk bracket from the body.

4. Loosen the screws on the left and right side of the bracket holding the hard disk.

5. Separate the hard disk from the bracket holding the hard disk.

6. In the reverse order of removing the hard disk, assemble the new hard disk.

7. After replacing the hard disk, turn on the power of the device.

8. Reference

Before use

- Each SATA cable must be connected to the connecting port precisely.

- Do not vertically put the hard disk in upright position or put other objects on top of the hard disk.

- When connecting/disconnecting the hard disk, do not use a motored tool.

- Refer to the following when adding/replacing the hard disk.

Connecting E-SATA HDD

• Turn o the power of DVR then connect E-SATA HDD to E-SATA port. And turn on the power of E-SATA HDD rst then turn on the power of DVR.

• E-SATA HDD is used only for recording, it cannot be used for any other purpose like backup, for example.

Recommended list of hard disk

Hard disks of below are the ones proved to be compatible through experiment. Please refer to when adding or replacing the hard disk.

Capacity LE6016

ST3250310CS

250 GB

ST3250312CS

Seagate

500 GB ST3500312CS

1 TB ST3100322CS

CAUTION

When you select the hard drive in use for resetting, the video data saved previously will be deleted. Therefore you must be careful.

Database recovery of the HDD

• The system has the check process of the database condition during the system booting. If

there is some problem, the system will be displayed the conrmation window to recover the database.

• Recovery time of the database is proportional to the amount of data.

• Recovery time takes more than 16 times if database recover included event data.

• Basically, the recorded data is not damaged because it always make the backup data.

21Before use

Arrangement of the database on the HDD

• The system will be displayed the confrimation window to arrange the database at the reboot

time every 6 month when you use the device normal. If you do not database arrangement, the system will perform the database arrangement every 12 month at booting point.

Check the HDD problem

• If you install the hard disk rst time, or do the Initialization, or shut down equipment

abnormally more than three times consecutively, the system checks integrity of the hard disk when booting.

• The system will be random check the bad sector on the hard disk.

Before use

22 Functional description

3 Functional description

3-1. Operation

Start Up

1. Turn on this device, then it boots with power indicator light turned on.

2. After booting it will be displayed as the LOGOUT id.

Functional description

3. Pressing

button to continue.

[USER]

You may select user to login and authority is restricted by kind of user. The access rights can be set for each user.

1) admin for system administrator (Access rights to Live, Search and Setup)

2) user1/user2/user3 for general user (Access rights can be set by administrator)

button, then the login window would be displayed. Select user and press “OK”

[PASSWORD]

The default user and password are set to ‘admin’ and ‘000000’ as shown above. Click password input area, you will see the screen keypad as right.

4. Input password by using virtual keypad on screen.

5. Click “OK” button to execute DVR system and you will see live screen.

23Functional description

Shutdown

1. While the status is logged in, press button, then logout window will be displayed as below.

SELECTION: Select the Log Out or EXIT.

USER : Display current user has logged. (admin/user1/user2/user3)

PASSWORD : Input password.

2. Click “OK” button to “Log Out” or “DVR Shutdown”.

Functional description

24 Functional description

3-2. Monitor Screen

Functional description

[Camera name]

• Shows camera name

• If you want to modify camera name, you can do so by selecting [Setup] Ò [Camera] [Channel]



[Status icon] (OSD)

• Status icon shows current status of camera/recording.

• (OSD Feature)

Item Icon Description Item Icon Description

Camera

Recording

Audio Icon

Motion Icon Recording by Motion

PTZ Icon Non Recording

Continuous Recording

Recording

Immediate Recording

Recording by Sensor

[Channel selection]

• Selected channel shows green rectangle on the edge of the screen.

[Live view]

• It shows current live view as real time.

[System control toolbar]

a b c d e f g h i j k l m n o p

r s t u

[Network status display]

• It shows current connection status of network.

(Black : It shows disconnected status.)

(Blue : It shows connected status.)

25Functional description

Functional description

• If you want to modify network settings, you can do so by selecting [Setup] Ò [Network] Ò [TCP/IP]

[Current Date/Time]

• Current date and time is displayed.

• If you want to modify date and time, you can do so by selecting [Setup] Ò [System]

[Date]

[Setup]

• Set the system environment and function.

• Refer to Chapter “3-3. System Setting”.

[Live screen]

• This is the button to switch over to the live display window to view the realtime video screen.



[Search]

• This is the button to switch over to the search window to view the recorded screen.

• Refer to Chapter “3-5. Search (Playback) & Backup”



[PTZ control]

• This is the button to control the PTZ camera

• Refer to Chapter “3-4. PTZ Control”.

+ 56 hidden pages