LG LE3108D-NH, LE2108D-NH, LE2116D-NH User Manual

DIGITAL VIDEO RECORDER

OWNER’S MANUAL

MODEL: LE3116D LE3108D LE2116D LE2108D

Before connecting, operating or adjusting this product, please read this owner’s manual carefully and completely.

AB28

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to

alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications.

Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

•A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user.

•Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose

of used batteries according to the manufacturer ’s instructions.

•Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.

This Class A digital apparatus complies with Canadian ICES-003.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

Caution: This installation should be made by a qualified service person and should conform to all local codes. Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Caution: The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus.

Caution:

This product employs a Laser System.To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center. Performing controls, adjustments, or carrying out procedures other than those specified herein may result in hazardous radiation exposure.To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.

To disconnect power from mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

This product is manufactured to comply with EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/EC.

European representative :

LG Electronics Service Europe B.V.

Veluwezoom 15, 1327 AE Almere,

The Netherlands (Tel : [phone])

Disposal of your old appliance

1.When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/ EC.

2.All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3.The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4.For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

IMPORTANT SAFETY INSTRUCTIONS

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Program

Additional

Safety warnings and Cautions

The following are warnings and cautions for the safety of the users and for the prevention of any property damage. Please read the following carefully.

WARNING

•Turn off the system before installation. Do not plug in several electric devices to the same outlet.

-This may cause heating, fire, or electric shock.

•Do not place any liquid container on the system, such as water, coffee, or other beverage.

-If liquid is poured onto the system, it can cause a system breakdown or fire.

•Prevent the power cable from being severely bent or having pressure exerted on it by a heavy object.

-This may cause fire.

•Clean the dust around the system on a regular basis. When cleaning the system, always use a dry cloth. Do not use a wet cloth or other organic solvents.

-This may damage the surface of the system and can cause a system breakdown or electric shock.

•Avoid any place with moisture, dust, or soot.

-This can cause fire or electric shock.

•When pulling the power cable from the plug, do so gently. Do not touch the plug with wet hands and avoid using the plug if the holes in the outlet are too loose.

-This may cause fire or electric shock.

•Do not attempt to disassemble, repair, or modify the system on your own. It is extremely dangerous due to the high voltage running through the system.

-This may cause fire, electric shock, or serious injury.

•Check for any danger signs such as a moist floor, a loosened or damaged power cable, or an unstable surface. If you encounter any problems, ask your dealer for assistance.

-This may cause fire or electric shock.

•Keep a distance of at least 15cm between the back of the system and the wall for the cables connected to the system otherwise, they may be bent, damaged, or cut.

-This may cause fire, electric shock, or injury.

•Install the system in a cool place without direct sunlight and always maintain room temperature. Avoid candlelight and heat generating devices such as heaters. Keep the system away from places where many people pass.

-This may cause fire.

•Install the system on a plain surface with sufficient air ventilation. Do not place the system on an elevated surface.

-This may cause system breakdown or serious injury.

•The power outlet must be placed on the ground, and the voltage range must be within 10% of the voltage rate. Do not use the same outlet with a hair dryer, iron, refrigerator, or any heating appliances.

-This may cause fire, over heating or electric shock.

•When the system’s battery is depleted, replace it with the same or equivalent type of battery specified by the manufacturer. Depleted batteries

should be discarded according to the manufacturer’s instructions.

-This may cause an explosion.

•If the system’s HDD exceeds its life span, you may not be able to recover any data stored inside the HDD. If the video on the system screen appears ‘damaged’ while playing a record-

ing stored inside the system’s HDD, it must be replaced with a new one. Ask for an engineer’s assistance for HDD replacement from your dealer.

-LG Electronics is not responsible for deleted data caused by user mishandling.

CAUTION

Please beware of the following precautions before installing the DVR.

•Avoid positioning the product in any place where the unit may come into contact with moisture, dust, or soot.

•Avoid placing in direct sunlight or near heating appliances.

•Keep the product away from electric sparks or magnetic substances.

•Avoid temperature extremes (recommended operating temperature is between 0°C - 40°C).

•Do not place any conductive material through the ventilation grills.

•Keep the system turned off before installation.

•Ensure enough space is left for cable connections.

•Place the system on a solid surface with sufficient air ventilation. Avoid any surface that vibrates.

•Placing the system near electronic devices such as a radio or a TV may cause the product to breakdown.

•Do not disassemble the product without seeking assistance from LG Electronics.

•Do not place any heavy object on the system.

•Prevent any substances from being inserted into the system.

-This may cause system breakdown.

•Install the system in a place with sufficient air ventilation.

-Keep at least 15cm distance between the back of the system and the wall, and at least 5cm distance between the side of the system and the wall.

•Do not install the system in a place with high magnetic, electric wave, or wireless devices such as a radio or a TV.

-Do not install the system in a place with magnetic objects, electric frequencies, or vibration.

•Do not place any heavy object on the system.

-This may cause system breakdown.

•Install the system on a stable, level surface.

-The system may not operate properly.

•Install the system in a place with appropriate moisture and temperature levels.

-Avoid installing the system in a place with high (over 40°C) or low (under 0°C) temperature.

•The system can be damaged from a strong impact or vibration. Avoid throwing objects within the vicinity of the system.

•Avoid direct sunlight or any heating appliances.

-Recommended operating temperature is over 0°C (32°F).

•Ventilate the air inside the system operation room, and tighten the system cover firmly.

-System breakdown may be caused by an inappropriate environment.

It is recommended to use AVR (Automatic Voltage Regulator) for a stable power supply.

It is recommended to coil the core-ferrite around the connector of the system to avoid electromagnetic interference.

•The outlet must be placed on the ground.

•If there is strange sound or smell, unplug the power cable immediately and contact the service center.

-This may cause fire or electric shock.

•In order to maintain stable system performance, have your system checked regularly by the service center.

-LG Electronics is not held responsible for system breakdown caused by user mishandling.

-There is a risk of explosion if a battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.

•Do not overturn the product during use.

Contents
INTRODUCTION...................................	7
Features................................................................	7
Front Panel............................................................	8
Accessories...........................................................	9
Rear Panel .........................................................	10
Remote Control...................................................	11
HOOKUP AND SETTINGS................	12
Basic Connection Overview................................	12
Connecting the RS-422/485 Device....................	13
Connecting Sensor Input and Alarm Output.......	13
Connecting the USB Device................................	14
Network Connection............................................	14
Connecting the RS-232C Port.............................	14
Concerning the Internal Hard Disk Drive............	15
Installing or Replacing the Hard Disk Drive .......	15
System Operation................................................	18
System Shutdown...............................................	18
Selecting the main monitor type..........................	19
General Explanation of the LiveScreen on the
Main Monitor..................................................	20
Selecting Live Screen Mode ..............................	21
PTZ Camera Control...........................................	22
Viewing System Information ...............................	24
Viewing the System Log List ..............................	24
Menu Configuration.............................................	25
Camera Settings..................................................	26
Schedule Settings...............................................	28
Display Settings...................................................	31
Event Settings.....................................................	32
Network Settings.................................................	33
System Settings..................................................	36
RECORDING......................................	41
Instant Recording................................................	41

SEARCH AND PLAYBACK...............	42
PLAYBACK.........................................................	42
SEARCH.............................................................	43
Functions Available During Playback..................	46
EXPORT .............................................................	47
CLIENT PROGRAM...........................	48
PC Requirements................................................	48
Client Program Installation..................................	48
Connecting to the DVR.......................................	48
Main Screen of DVR Client Program..................	50
Live Mode............................................................	51
Search Mode.......................................................	54
Remote Setup Mode...........................................	55
Remote Export Settings......................................	61
ADDITIONAL PROGRAMS................	62
Emergency Agent Program.................................	62
Main Screen of Emergency Agent......................	62
Export Viewer Program.......................................	63
Web Viewer Program..........................................	64
REFERENCE......................................	66
Troubleshooting...................................................	66
Recommended Devices......................................	69
Time zones..........................................................	70
Factory Default Configuration Settings...............	71
Recording Time Table (250GB HDD).................	74
Specifications......................................................	76

INTRODUCTION

Features

•Stable embedded Linux operating system.

•Journal filing system for HDD file recovery following power recovery.

•Small file sizes with MPEG-4 compression.

•Internal storage expandable to 3TB. (Expandable if new high capacity HDD is launched)

•NTSC and PAL selectable video format.

•Full realtime recording.

-Up to 480IPS@352 X 240: LE3116D NTSC

-Up to 400IPS@352 X 288: LE3116D PAL

-Up to 240IPS@352 X 240: LE3108D NTSC

-Up to 200IPS@352 X 288: LE3108D PAL

-Up to 240IPS@352 X 240: LE2116D NTSC

-Up to 200IPS@352 X 288: LE2116D PAL

-Up to 120IPS@352 X 240: LE2108D NTSC

-Up to 100IPS@352 X 288: LE2108D PAL

•Various recording resolutions and quality levels.

-D1(704x480), Half D1(704x240), CIF(352x240)

:NTSC

-D1(704x576), Half D1(704x288), CIF(352x288)

:PAL.

-5 step quality level (Highest, High, Standard, Low, Lowest).

•Easy operation using various user interface & user friendly GUI.

-Optical mouse, Full function IR remote controller, Jog/Shuttle

•Powerful multiplex function.

-Simultaneous live display, recording, playback, network transmission, back-up.

•Various search function.

-Date/time search (calender search), event search, bookmark search, smart search.

•Event data protection by event partition recording.

•Pre-alarm recording (Up to 1minute).

•Motion event recording and preview test function of motion sensitivity.

•Recording image rate & quality adjustment per individual camera.

•Powerful record scheduling.

•Instant playback in surveillance mode.

•POP (picture over picture) playback.

-Viewing live and playback video simultaneously.

•Perfect audio/video synchronization.

•Automatic backup by schedule.

•Image authentication (Watermark).

•Three USB 2.0 ports for backup interface.

•Setup configuration export/import with USB memory stick or network.

•Easy system S/W update with USB memory stick or network.

•Clients S/W can manage max 100 DVR servers.

•Max five clients can access one DVR server simultaneously.

•Network bandwidth throttle.

-Automatically adjust a bandwidth according to network speed status of unit.

•Remote alarm notification via client software or E-mail.

•Time and date sync from NTP server.

•Daylight saving mode.

•Covert camera protection.

•Back-up CD auto run.

•User management (User level control).

•PTZ Control.

-For more details see page 69.

-Dome camera telemetry control (Dome OSD control).

Model LE3116D (16 Channel) is used for the description, operation and details provided in this operating guide.

Introduction

Front Panel

x LE3116D/LE2116D

a b

h

i

j

x LE3108D/LE2108D

a b

h

i

j

aPlayback Control Buttons

-X: Pauses playback.

-m/c, .: Search the recorded images in reverse or skip the recorded images.

-bB: Playback or reverse playback of recorded images.

-M/C, >: Forward search the recorded images or skip the recorded images.

-x: Stops playback.

bNET Indicator

Lights when the network is connected.

HDD Indicator

Blinks when the HDD is accessed.

ALARM Indicator

Lights when the alarm out is in progress.

BACK UP Indicator

Lights when the data back up is in progress.

cd e f g

k l mnopq r

cd e f g

k l mnopq r

c Channel Buttons

You can input a number with channel buttons. You can also use the channel buttons for subfunction with SHIFT button (11~16 buttons of 8 channel DVR are used for subfunction without SHIFT button.). The LED in the button indicates the status as follows:

- Off: The current status is for live mode

- Blue: Recording mode.

Blinks when an event occurs.

(3) FOCUS - / (4) FOCUS +

Adjusts focus position.

(5) OSD

Accesses or removes the System Control Bar (OSD).

(6) INFO

Displays or removes system information.

(7) IRIS - / (8) IRIS +

Adjust iris position.

(9) ALM.OFF

Cancels alarm activation and returns the system to the condition before the alarm was activated.

(10/0) LOG

Displays or removes the System Log List.

(11) SET

Registers the PTZ camera's preset position.

(12) CLEAR

Deletes a memorized preset position.

(13) COPY

Copies the recording data to an external device.

(14) MARK

Sets the mark point for recording search.

(15) MOVE

Moves the camera to the preset position.

(16) TOUR

Tours all registered preset positions in the camera.

dArrow Buttons (b B v V)

Select or move between the menu options.

ENTER

Confirms menu selections.

eSETUP/ESC

Displays the setup menu or cancels operation on the setup menus.

SEARCH

Displays the search menu.

REC

Starts or stops instant recording.

fShuttle Ring

Fast forward or reverse picture search when the dial is rotated.

gJOG Dial

Allows a forward or reverse frame search. In pause mode, plays recorded images

frame by frame through rotation. Increases or decreases the options value.

h1 Power

Turns DVR on or off.

Press and hold for more than 2 seconds to turn on or off.

iDisc Tray

Insert a disc here.

jZ (OPEN/CLOSE)

Opens or closes the disc tray.

kSHIFT

If you use the Sub-function of the channel button, the button is activated.

lZOOM + / -

Zooms in/out on playback window.

mPTZ

Switches this unit to PTZ mode to control the PTZ camera connected.

nMAIN

Display the MAIN menu to set the screen mode to full, 4, 6, 8, 9 or 16 screens. Set the video output signal to VGA mode.

oSPOT

Enter SPOT mode to allow spot monitor control.

pLOCK

Displays the lock menu to change the user type or disable the system operation.

qRemote Sensor

Point the remote control here.

rUSB Port

Connect an external USB device for backup or playback.

Accessories

Software
Install CD		Remote
Rack Mount		Control
Bracket
Screws	AAAAAA	AAA Type
		Battery

Note: The accessories may be different depending on models.

Power Plug

Mouse

SATA cable

Introduction

Rear Panel

x LE3116D/LE2116D

ab

d e f gh i j kl

x LE3108D/LE2108D

ab

d e f gh i j kl

aVIDEO INPUT

Connect the camera’s video output to these BNC connectors.

bLOOP OUT

The signal from VIDEO INPUT connector is looped out to this connector.

cPower Cord Inlet (AC IN)

Connect the power plug.

dRS-422/485 Terminals

Connect RS422/485 compatible cameras. Connect the LKD1000 controller to DATA2 terminal.

eRS-232C Connector

Used to connect to a host device equipped with RS-232C connector (such as a personal computer). This unit can be controlled from other devices via this connector.

fRELAY-OUT Terminals

Output terminals for alarm(relay) signal.

c

mn

c

mn

gAUDIO INPUT

Connect the audio output of an external device.

hSPOT-OUT (BNC Type Connector)

Connect to spot monitor or display device.

iLAN Port

Connect the ethernet 10/100Mbps network cable for controlling this unit via a PC network.

jMAIN-OUT (BNC Type Connector)

Connect to main monitor or display device.

kAUDIO OUT

Connect the audio input signal of an external device.

lVGA

Connect a VGA monitor.

mUSB Ports

Connect an optional extension USB device.

nALARM-IN Terminals

Input terminals for alarm(relay) signal.

10

Remote Control

POWER (1)

Turns DVR on or off.

LOCK

Displays the lock menu to change user type or disable system operation.

ID

Set the appropriate DVR system ID to operate via the IR Remote Controller when using the multiple DVR.

Press the ID button then press the number button within 2 seconds to select the system ID of the DVR.

If you set the system ID to “0”, you can control multiple DVR at the same time.

MAIN

Displays the MAIN menu to set the screen mode to full, 4, 6, 8, 9 or 16 screens.

SPOT

Enter SPOT mode to allow spot monitor control.

ALM.OFF

Cancels alarm activation and returns the system to the condition before the alarm was activated.

OSD

Accesses or removes the system control bar (OSD).

SETUP/ESC

Displays the setup menu or cancels operation of the setup menu.

Arrow Buttons (b B v V)

Selects or moves between the menu options.

ENTER

Confirms menu selections.

COPY

Copies the recording data to an external device.

SEARCH

Displays the search menu.

MARK

Sets the mark point for recording search. You can set the mark point during the single channel playback of recorded data.

PAUSE (X)

Pauses playback.

STOP(x)

Stops playback.

REC (z)

Starts or stops recording.

m/c/.

Searches the recorded images in reverse or skips the recorded images.

bB

Playback or reverse playback of recorded images.

M/C/>

Forward searches the recorded images or skips the recorded images.

Number Buttons (0,1-9)

To select the PTZ preset number, ID, or channel.

INFO

Displays or removes the system information window.

LOG

Displays or removes the System Log List window.

PTZ

Switches this unit to PTZ mode to control the connected PTZ camera.

TOUR

Tours all registered preset positions in the camera.

ZOOM + / -

Zooms in/out on the playback window.

FOCUS + / -

Adjusts the focus of a camera.

IRIS + / -

Adjusts the iris of a camera.

PRESET

-SET: Registers the PTZ camera's preset positions.

-CLEAR: Deletes a memorized preset position.

-MOVE: Moves the camera to the preset position.

F1

This button is not available.

Introduction

11

HOOKUP AND SETTINGS

Precautions

•Depending on the camera and other equipment there are various ways to connect the unit. Please refer to the camera manual or manuals for other devices as necessary for additional connection information.

•Be sure to switch off the camera before installation and connection.

Basic Connection Overview

Connect the coaxial-type cameras Connect the Monitor, DVR, VCR, or others.

Connect

power code

	Connect PTZ cameras,
	DVRs or keypads	Connect alarm sensors.
	(optional).
	Connect audio
	(line input)	Connect mouse
	Connect the alarm (relay)	for use with this
		operating system
		or USB device for
		backup, copy or
	Connect	others.
	BNC type
	spot monitor.
	Connect network cable	For audio amplifier
	for client control.
	Connect	Connect VGA monitor.
		(Default output)
	BNC type
	monitor.

12

Connecting the RS-422/485

Device

This DVR has two data terminals.

Use this port to connect PTZ cameras, DVRs or keypads (optional).

Rear of

the DVR

5~7 mm

PTZ Units

TXTX+

(RS-422/485 TYPE)

RS-422/485 Terminal

Description

TX - (DATA -)

Data Transmission

TX + (DATA +)

Data Transmission

RX - (DATA -)

Data Reception

RX + (DATA +)

Data Reception

GND

Shield

Connecting the PTZ camera

Connecting the PTZ serial communication lines to the RS-422/485 terminal.

Notes:

•When connecting lines, connect the TX - of the DVR to RX - of the PTZ unit and TX + of the DVR to RX + (TX +: LG_LS903 protocol only) of the PTZ unit correctly.

•Recommended initial data are 9600 Baud Rate, 8 Data bits, 1 Stop bit and No parity.

•When connecting PTZ cameras to DVRs it is necessary to set the setup menu for this unit according to the RS-485 settings of the camera and DVRs.

Connecting the LKD1000 controller

Connecting the LKD1000 controller to control the DVR. (Refer to the manuals of the LKD1000 controller for more details.).

Connecting Sensor Input and Alarm Output

Alarm terminals are used to connect the alarm devices such as sensors, door switches, etc.

Sensor Input

You can connect up to 16 alarm sensors (LE3108/ LE2108: 8 alarm sensors).

Each alarm sensor should be connected with G (GND). The signal state is adjustable to N/O (Normal Open) or N/C (Normal Close) through the setup menu.

Rear of the DVR

Terminal No.	Description
1	Sensor Input 1
2	Sensor Input 2
3	Sensor Input 3
4	Sensor Input 4
G	Ground
5	Sensor Input 5
6	Sensor Input 6
7	Sensor Input 7
8	Sensor Input 8
G	Ground
9	Sensor Input 9
10	Sensor Input 10
11	Sensor Input 11
12	Sensor Input 12
G	Ground
13	Sensor Input 13
14	Sensor Input 14
15	Sensor Input 15
16	Sensor Input 16
G	Ground

Settings

Hookup and

13

Alarm Output

Connect up to 4 separate alarms (LE3108/LE2108: 2 separate alarms) to the alarm output.

Alarm signal output at an event occurrence. Rear of the DVR

Note:

The internal switching relays are rated for 0.3A at 125V AC or 1A at 30V DC. If the electric current is higher than that the unit can be damaged.

Terminal No.	Description
G	Ground
1	Alarm output 1
2	Alarm output 2
3	Alarm output 3
4	Alarm output 4

Connecting the USB Device

USB Memory Device

Insert the memory device into the USB port. The system automatically recognizes the device.

Using a USB memory device the system S/W can be easily upgraded.

USB Backup Device

Connect the USB cable of the USB backup device to the USB port on the rear panel of the unit.

(Example: HDD or other external storage.)

Mouse

Connect the USB mouse for function control of the unit.

Network Connection

LAN Connection

Connect the LAN port to an available 10/100 base-T port with a straight ethernet cable (not supplied). The NET indicator on the front panel will be lit.

Automatic Network Configuration

The DVR can automatically obtain and configure the network interface via DHCP. (see page 33)

Manually Configure Network

The DVR may be manually configured by assigning an IP address, subnet mask, gateway DNS. (see page 33)

Connecting the RS-232C Port

The RS-232C is used for communication with a connected PC. This terminal is compliant with the RS232C standard.

14

Concerning the Internal Hard

Disk Drive

The internal hard disk drive (HDD) is a fragile piece of equipment. Please follow the guidelines below when using the DVR to protect against possible HDD failure.

We recommend that you back up your important recordings onto an external backup device in order to prevent accidental loss.

Make sure that the power is turned OFF when attaching or removing the HDD.

•Do not move the DVR while the power is on.

•Do not use the DVR in excessively hot or humid places, or in places that may be subject to sudden changes in temperature. Sudden changes in temperature can cause condensation to form inside the DVR. This can be a cause of HDD failure.

•While the DVR is switched on, do not unplug from the wall socket or switch the electricity off from the breaker switch.

•If there’s a power failure while the DVR is on there is a chance that some data on the HDD will be lost.

•Do not drop the HDD. Also do not put the metallic object such as coins or screwdrivers into the HDD tray.

•When a power failure occurs during recording, avoid adding, replacing or transporting the HDD as the recorded data may be erased. In this case, turn the power back on to boot up the unit normally with the HDD that was being used at the time of the power failure attached. Then add, replace, or transport the HDD.

•The HDD is very delicate. Handle the HDD with care and follow the precautions below because even a small shock may damage the internal components of the HDD.

-Do not place the HDD on a desk or a table directly. Put a thick cushion under the HDD because even a small shock may damage the internal components of the HDD.

-Do not use an electric screwdriver. Vibrations and shocks caused by an electric screwdriver may damage the internal components of the HDD.

-When replacing the HDD, do not knock the HDD with other components such as another HDD and the HDD tray.

-Do not knock the HDD with tools such as a driver when replacing the HDD.

•Protect the hard disk drives from static electricity.

Installing or Replacing the Hard Disk Drive

Installing the Hard Disk Drive

You can install up to 4 HDDs.

However, since the product contains many parts which may incur electric shocks, accidents or product breakdown, and because improper installation or setup may disturb HDD recognition or normal product operation, you should consult with an expert from the store where the product was purchased.

Turn the power of the unit off and detach the power plug from the outlet.

1.Remove the fixing screws on the left/right side and rear panel.

2.Detach the top case by sliding it after removing the screws.

3.Remove the screws and detach the hard disk mounting brackets from the unit.

4.Attach the HDD onto the hard disk mounting brackets with four screws.

Settings

Hookup and

15

5. Attach the hard disk mounting brackets with the	• When installing 3 HDDs.
screws.	1.	Connect the SATA cable of the first HDD to
6. Connect the HDD power cable.		the first SATA connector of the main board.
		It use for main system HDD.
	2.	Connect the SATA cable of the second
		HDD to the second SATA connector of the
		main board.
	3.	Connect the SATA cable of the third HDD
		to the third SATA connector of the main
		board.

7. Connect the SATA cable.

8.Connect the SATA cable to the SATA connector on the main board.

•When installing 1 HDD.

Connect the SATA cable of the HDD to the first SATA connector. It is use for main system HDD.

•When installing 4 HDDs.

1.Connect the SATA cable of the first HDD to the first SATA connector of the main board. It use for main system HDD.

2.Connect the SATA cable of the second HDD to the second SATA connector of the main board.

3.Connect the SATA cable of the third HDD to the third SATA connector of the main board.

4.Connect the SATA cable of the fourth HDD to the fourth SATA connector of the main board.

•When installing 2 HDDs.

1.Connect the SATA cable of the first HDD to the first SATA connector of the main board. It use for main system HDD.

2.Connect the SATA cable of the second HDD to the second SATA connector of the main board.

9.Assemble the top case.

10.Fix the screws.

11.After installing the HDD, you must format the HDD using the setup menu (See page 38).

Notes:

•When you add the new HDD, do not change the position of the HDD. It may delete the current data and cause a malfunction.

•You should install one of the HDDs on the first connector of the main board. If you do not install the HDD on the first connector of the main board, the DVR will not work properly.

16

Replacing the Hard Disk Drive

Turn the power of the unit off and detach the power plug from the outlet.

1.Follow steps 1-3 described in “Installing the Hard Disk Drive”.

2.Remove the connector from the HDD.

3.Remove the screws from the hard disk drive on the left/right side of the hard disk the mounting bracket.

4.Remove the HDD from the hard disk mounting bracket.

5.Install the new HDD in the reverse order to when replacing the hard disk drive.

6.After replacing the hard disk drive, insert the power plug into the outlet and turn the power of the unit on.

Notes:

•Make sure that each of the SATA cables is connected to the connector housing through its holes.

•Do not stack them nor keep them upright.

•Do not use an electric screwdriver to fix them.

Recommended HDD

The following HDD has been tested and compatibility is ensured. When you attach multiple HDDs use the recommended HDDs.

Note:

If you do not use the recommended HDD, the system may not be operated normally.

Maker	RPM	Capacity	Interface	Model No.
	7,200	250 GB	SATA	ST3250311SV
Seagate	7,200	500 GB	SATA	ST3500410SV
	5,400	1 TB	SATA	ST31000424CS
Hitachi	5,700	1 TB	SATA	HCS5C1010CLA382

Settings

Hookup and

17

System Operation

1.Press and hold 1 (POWER) button until the beep sounds to turn on the unit. System booting will commence. The LG logo image will be displayed on the main monitor during the system booting.

2.When the booting is completed the live window will be displayed. Click the LOCK button on the system control bar or press the LOCK button on the remote control to display the log-in window.

3.Select a user name by using the mouse or arrow and the ENTER button on the remote control or front panel.

• User access rights

	User Level	Administrator	Power	Normal
			User	User
	View	YES	YES	YES
	Live Video
	Alarm Off	YES	YES	NO
	PTZ	YES	YES	NO
	Instant Record	YES	YES	NO
	Export	YES	YES	NO
	Search/Play	YES	YES	NO
	Setup	YES	NO	NO
	Shut Down	YES	NO	NO

-ADMINISTRATOR: Unlimited operation of the unit.

-Power User: Use of the limited functions of the system. (The setup configuration is not allowed to change.)

-Normal User: Use of the limited functions of the system. (Split monitor and live image view are available.)

4.Enter the password by using the virtual keyboard. (Initial password is “000000”.)

5.Press LOCK or click the OK(LOCK) icon.

You can see the live screen and operate the system.

Notes:

•You are not allowed to connect the VGA monitor and the composite monitor simultaneously. Consequently, the user is obliged to choose either the composite monitor or the VGA monitor. When set to composite monitor there is no VGA output. When set to VGA monitor there is no composite output. SPOT-OUT is unaffected by the monitor setting.

•This DVR is based on a VGA monitor using OSD. We recommend to using the VGA monitor with this unit. If you use a composite monitor, the OSD quality may lower to read it.

System Shutdown

1.First, you must stop playback and exit the setup menu.

In playback, press STOP.

2.Press and hold 1 (POWER) button until the beep sounds and the logout window will be displayed.

3.Enter the password by using the virtual keyboard.

4.Press LOCK or click the OK(LOCK) icon. The system will shutdown.

18

Selecting the main monitor type

You can select the main monitor type to display the main screen on the power on condition.

Using the VGA Monitor

1.Connect the VGA monitor to the VGA jack on the rear of the DVR.

2.Turn on the VGA monitor.

3.Press and hold the MAIN button on the front panel until the beep sounds to display the main screen. The DVR will restart and then the VGA monitor is set as a main monitor.

CCTV (Composite Video Type) Monitor

1.Connect the CCTV monitor to the MAIN-OUT jack on the rear of the DVR.

2.Turn on the CCTV monitor.

3.Press and hold the SPOT button on the front panel until the beep sounds to display the main screen. The DVR will restart and then the CCTV monitor is set as a main monitor.

Note:

You can select the monitor type by using the MAIN or SPOT button at anytime. If you change the monitor type, the system will be rebooted automatically.

Settings

Hookup and

19

General Explanation of the Live Screen on the Main Monitor

Main Monitor Screen

ab c d e f

a Channel Number

Displays the channel number.

b Channel Name

Displays the edited channel name.

c Camera Status Icon

• PTZ camera icon

Displays the PTZ camera status.

• Input audio icon

Displays the input audio status.

• Recording status icon

Displays the recording status.

- Green “C” indicates continuous recording. - Green “I” indicates Instant recording.

- Red “S” indicates sensor triggered recording.

- Blue “M” indicates motion detection recording.

- White “N” indicates the channel is not being recorded.

dSelected Channel

Displays the selected channel with red box.

eLive Screen

Displays the current surveillance live screen.

f System Control Bar

Displays the current date and time.

Displays the setup menu.

Displays the search menu.

Displays the PTZ remote control window.

Displays the screen division selection window for the main monitor.

Displays the screen division selection window for the spot monitor.

Displays the lock menu to change the user type or disable system operation.

Displays the system log list window.

Turns the alarm off.

Displays the system information window.

Displays the remaining HDD status.

-N (Normal partition): Used size/total size.

-E (Event partition): Used size/total size.

Display/hide playback control bar.

Pause playback.

Jump to the beginning of the current data recorded on the same date.

Select the required scanning speed.

Jump to the last minute of the current data recorded on the same date.

Stop playback.

Display playback status.

Enlarge/reduce the playback window.

Click at a desired point to be marked during playback. Up to 15 points can be marked.

Display copy(export) menu.

Note:

Use OSD with the SHIFT button on the front panel or click the right button on the mouse to display / remove the system control bar displayed on-screen.

20

Selecting Live Screen Mode

Main Monitor

You can select the live screen mode to display a full, 4-split, 6-split, 8-split, 9-split or 16-split screens on the main monitor.

1.Press MAIN or click the MAIN icon in the system control bar.

Screen mode select menu of main monitor is displayed on the main monitor.

2.Select screen mode.

Selected Main Channel

Screen mode

Selected split mode

Sequence

Channel Buttons

-Channel Number: Press the 1 to 16 channel button to see the current surveillance images in selected live screens on the main monitor.

-Full Screen Mode: When you see the selected channel on the full screen.

-4, 6, 8, 9 and 16 Split Mode: Displays selected split screens on the main monitor.

-Sequence: View all channels in sequence.

3.Select [OK (MAIN)] and press ENTER to confirm your selection.

Note:

To display the screen you desire to watch in full screen mode, double click the desired channel.

Spot Monitor

You can select the live screen mode to full or 4-split screens on the spot monitor.

1.Press SPOT or Click the SPOT icon in the system control bar.

Screen mode select menu of spot monitor is displayed on the main monitor.

2.Select screen mode.

Selected spot channel

Selected split mode

Screen mode Sequence

Channel buttons

-Channel Number: Press the 1 to 16 channel button to see the current surveillance image on the spot monitor.

-Full Screen Mode: When you see the selected channel on the full screen.

-4 Split Mode: Displays 4 split screens on the spot monitor.

-Sequence: Views the all channels in sequence.

3.Select [OK (SPOT)] and press ENTER to confirm your selection.

Settings

Hookup and

21

PTZ Camera Control

You can control the cameras connected via the data port of RS-422/485 terminal. You must set the configuration between the PTZ camera and the DVR.

1.Select the PTZ camera channel on the main monitor you want to control.

2.Press PTZ or Click the PTZ icon in the system control bar.

Virtual PTZ remote control is displayed on the main monitor.

3.Use each item to control the PTZ camera.

a

b

c

d e

f

g

hj

ik l

aExit

Remove the PTZ virtual remote control.

bv/V/b/B

Use to pan/tilt the camera.

Confirm the preset position.

cZOOM + / -

To adjust the camera zoom.

dFOCUS + / -

To manually adjust the focus of a camera.

eIRIS + / -

To manually adjust the iris of a camera.

fDisplays the Selected Preset Number

gNumber Buttons

To input the preset number.

hSET

To register preset positions.

iMOVE

To move the camera to the preset position.

jCLEAR

To delete a memorized preset position.

kTOUR

To start a preset tour.

lSETUP

To displays the setup menu of the PTZ camera.

22

Preset Settings

Preset position is the function to register camera monitoring positions (preset positions) associated with position numbers.

By entering the position numbers, you can move cameras to the preset positions.

Note:

To activate this function, you need to register the preset positions of the PTZ cameras.

To Register Preset Positions

1.Move the camera to a point you wish by using the v/V/b/B.

2.Press SET or click the [SET] icon.

3.Select the preset number you wish to register.

4.	Press ENTER or click the [	] icon.
5.	The position and its number are memorized.
	Repeat steps 1-4 to add additional positions.

Note:

Preset numbers from 0 to 255 are available on this unit but the actual preset range differs depending on PTZ cameras.

Changing to a Picture in a Preset Position

The following function is available only with cameras provided with the preset function.

The preset function makes the combination camera move to the programmed preset position.

It is necessary to program preset positions for the combination camera beforehand.

1.Press the MOVE button or click the [MOVE] icon.

2.Use number buttons to enter the memorized preset position’s index number then press ENTER or

click the [ ] icon. The camera moves to the preset position and the picture of the camera in that position appears on the monitor.

To Clear the Preset Position

You can clear a memorized preset position.

1.Press the CLEAR button or Click the [CLEAR] icon.

2.Use number buttons to enter the memorized preset index number then press ENTER or Click the

[	] icon to clear the preset positions.

Note:

This function may not be available depending on PTZ cameras.

To Tour The Preset Positions

You can tour all preset positions.

1.Press the TOUR button or Click the [TOUR] icon. All registered preset positions in the camera will be selected and the camera position image will be switched on the active monitor.

2.You can stop the tour by pressing the TOUR button or clicking the [TOUR] icon.

Setup for PTZ Cameras

You can adapt the camera to your requirements by setting up the respective items in menus.

1.Click the [SETUP] icon.

The setup menu appears in the selected window of the main monitor.

2.Use arrows, ZOOM +/- and ENTER buttons to set the options.

Notes:

•Refer to the manuals of the PTZ camera for more details.

•Some PTZ cameras may not operated correctly with this unit.

•You cannot control the other functions when the PTZ virtual remote control is displayed.

Settings

Hookup and

23