LG LDV-S503 Owner’s Manual

LDV-S500_ENG

DIGITAL VIDEO
RECORDER

OWNERʼS MANUAL

MODEL: LDV-S504

LDV-S503

Before connecting, operating or adjusting this product,
please read this ownerʼs manual carefully and completely.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

This lightning flash with arrowhead symbol
within an equilateral triangle is intended to
alert the user to the presence of uninsulated
dangerous voltage within the productʼs enclo­sure that may be of sufficient magnitude to
constitute a risk of electric shock to persons.

The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and mainte­nance (servicing) instructions in the literature
accompanying the product.

FCC WARNING: This equipment may generate or use
radio frequency energy. Changes or modifications to
this equipment may cause harmful interference unless
the modifications are expressly approved in the instruc­tion manual. The user could lose the authority to oper­ate this equipment if an unauthorized change or modifi­cation is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to
Part 15 of the FCC Rules. These limits are designed to
provide reasonable protection against harmful interfer­ence when the equipment is operated in a commercial
environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in accor­dance with the instruction manual, may cause harmful
interference to radio communications.
Operation of this equipment in a residential area is likely
to cause harmful interference in which case the user
will be required to correct the interference at his own
expense.

• A suitable conduit entries, knock-outs or glands shall
be provided in the cable entries of this product in the
end user.

• Caution: Danger of explosion if battery is incorrectly
replaced. Replaced only with the same or equivalent
type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer ʼs
instructions.

• Holes in metal, through which insulated wires
pass,shall have smooth well rounded surfaces or
shall be provided with brushings.

Warning: Do not install this equipment in a confined
space such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with
the National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic envi­ronment this product may cause radio interference in
which case the user may be required to take adequate
measures.
Warning: To reduce a risk of fire or electric shock, do
not expose this product to rain or moisture.
Caution: This installation should be made by a qualified
service person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus should not be exposed to
water (dripping or splashing) and no objects filled with
liquids, such as vases, should be placed on the appa­ratus.

This product is manufactured to comply
with EMC Directive 2004/108/EC and Low
Voltage Directive 2006/95/EC.

European representative :

LG Electronics Service Europe B.V.

Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : [phone])

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol
is attached to a product it means the prod­uct is covered by the European Directive
2002/96/EC.

2. All electrical and electronic products should be
disposed of separately from the municipal waste
stream via designated collection facilities appointed
by the government or the local authorities.

3. The correct disposal of your old appliance will help
prevent potential negative consequences for the
environment and human health.

4. For more detailed information about disposal of your
old appliance, please contact your city office, waste
disposal service or the shop where you purchased
the product.

Caution:

This product employs a Laser System.To ensure proper
use of this product, please read this ownerʼs manual
carefully and retain it for future reference. Should the
unit require maintenance, contact an authorized service
center. Performing controls, adjustments, or carrying out
procedures other than those specified herein may result
in hazardous radiation exposure.To prevent direct expo­sure to laser beam, do not try to open the enclosure.
Visible laser radiation when open. DO NOT STARE
INTO BEAM.

To disconnect power from mains, pull out the mains
cord plug. When installing the product, ensure that
the plug is easily accessible.

2

IMPORTANT SAFETY INSTRUCTIONS

CAUTION:

This product has been designed and manufactured to assure personal safety. Improper use can result in elec­tric shock or fire hazard. The safeguards incorporated in this product will protect you if you observe the follow­ing procedures for installation, use, and servicing.
This product does not contain any parts that can be repaired by the user.

DO NOT REMOVE THE CABINET COVER, OR YOU MAY BE EXPOSED TO DANGEROUS VOLTAGE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL ONLY.

1. Read these instructions. - All these safety and

operating instructions should be read before the
product is operated.

2. Keep these instructions. - The safety, operating

and use instructions should be retained for future
reference.

3. Heed all warnings. - All warnings on the product

and in the operating instructions should be adhered
to.

4. Follow all instructions. - All operating and use

instructions should be followed.

5. Do not use this apparatus near water. - For

example: near a bath tub, wash bowl, kitchen sink,
laundry tub, in a wet basement; or near a swimming
pool; and other areas located near water.

6. Clean only with dry cloth. - Unplug this product

from the wall outlet before cleaning. Do not use
liquid cleaners.

7. Do not block any ventilation openings. Install
in accordance with the manufacturer's instruc­tions. - Slots and openings in the cabinet are pro-

vided for ventilation and to ensure reliable operation
of the product and to protect it from over-heating.
The openings should never be blocked by placing
the product on a bed, sofa, rug or other similar sur­face. This product should not be placed in a built­in installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturerʼs
instructions have been adhered to.

8. Do not install near any heat sources such as
radiators, heat registers, stoves, or other appa­ratus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polar­ized or grounding-type plug. A polarized plug
has two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong. The wide blade or the third
prong are provided for your safety. If the pro­vided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete
outlet.

PLEASE READ AND OBSERVE ALL WARNINGS AND INSTRUCTIONS IN THIS OWNERʼS

MANUAL. AND THOSE MARKED ON THE PRODUCT. RETAIN THIS BOOKLET FOR FUTURE
REFERENCE.

10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

11. Only use attachments/accessories specified
by the manufacturer.

12. Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus com­bination to avoid injury from tip-over.

13. Unplug this apparatus during lightning storms
or when unused for long periods of time.

14. Refer all servicing to qualified service person­nel. Servicing is required when the apparatus
has been damaged in any way, such as power­supply cord or plug is damaged, liquid has
been spilled or objects have fallen into the
apparatus, the apparatus has been exposed to
rain or moisture, does not operate normally, or
has been dropped.

PROGRAM

ADDITIONAL

3

Safety warnings and Cautions

The following are warnings and cautions for the safety of the users and for the prevention of any property
damage. Please read the following carefully.

WARNING

• Turn off the system before installation. Do not
plug in several electric devices to the same outlet.

- This may cause heating, fire, or electric shock.

• Do not place any liquid container on the system,
such as water, coffee, or other beverage.

- If liquid is poured onto the system, it can

cause a system breakdown or fire.

• Prevent the power cable from being severely
bent or having pressure exerted on it by a heavy
object.

- This may cause fire.

• Clean the dust around the system on a regular
basis. When cleaning the system, always use a
dry cloth. Do not use a wet cloth or other organic
solvents.

- This may damage the surface of the system

and can cause a system breakdown or electric
shock.

• Avoid any place with moisture, dust, or soot.

- This can cause fire or electric shock.

• When pulling the power cable from the plug, do
so gently. Do not touch the plug with wet hands
and avoid using the plug if the holes in the outlet
are too loose.

- This may cause fire or electric shock.

• Do not attempt to disassemble, repair, or modify
the system on your own. It is extremely danger­ous due to the high voltage running through the
system.

- This may cause fire, electric shock, or serious

injury.

• Check for any danger signs such as a moist
floor, a loosened or damaged power cable, or an
unstable surface. If you encounter any problems,
ask your dealer for assistance.

- This may cause fire or electric shock.

• Keep a distance of at least 15cm between the
back of the system and the wall for the cables
connected to the system otherwise, they may be
bent, damaged, or cut.

- This may cause fire, electric shock, or injury.

• Install the system in a cool place without direct
sunlight and always maintain room temperature.
Avoid candlelight and heat generating devices
such as heaters. Keep the system away from
places where many people pass.

- This may cause fire.

• Install the system on a plain surface with sufficient
air ventilation. Do not place the system on an
elevated surface.

- This may cause system breakdown or serious

injury.

• The power outlet must be placed on the ground,
and the voltage range must be within 10% of the
voltage rate. Do not use the same outlet with a
hair dryer, iron, refrigerator, or any heating appli­ances.

- This may cause fire, over heating or electric

shock.

• When the systemʼs battery is depleted, replace
it with the same or equivalent type of battery
specified by the manufacturer. Depleted batteries
should be discarded according to the manufactur­erʼs instructions.

- This may cause an explosion.

• If the systemʼs HDD exceeds its life span, you
may not be able to recover any data stored inside
the HDD. If the video on the system screen
appears ʻdamagedʼ while playing a record­ing stored inside the systemʼs HDD, it must be
replaced with a new one. Ask for an engineerʼs
assistance for HDD replacement from your dealer.

- LG Electronics is not responsible for deleted

data caused by user mishandling.

4

CAUTION

Please beware of the following precautions before installing the DVR.

• Avoid positioning the product in any place where the unit may come into contact with moisture, dust, or soot.

• Avoid placing in direct sunlight or near heating appliances.

• Keep the product away from electric sparks or magnetic substances.

• Avoid temperature extremes (recommended operating temperature is between 0°C - 40°C).

• Do not place any conductive material through the ventilation grills.

• Keep the system turned off before installation.

• Ensure enough space is left for cable connections.

• Place the system on a solid surface with sufficient air ventilation. Avoid any surface that vibrates.

• Placing the system near electronic devices such as a radio or a TV may cause the product to breakdown.

• Do not disassemble the product without seeking assistance from LG Electronics.

• Do not place any heavy object on the system.

• Prevent any substances from being inserted into
the system.

- This may cause system breakdown.

• Install the system in a place with sufficient air ven­tilation.

- Keep at least 15cm distance between the

back of the system and the wall, and at least
5cm distance between the side of the system
and the wall.

• Do not install the system in a place with high
magnetic, electric wave, or wireless devices such
as a radio or a TV.

- Do not install the system in a place with mag-

netic objects, electric frequencies, or vibration.

• Do not place any heavy object on the system.

- This may cause system breakdown.

• Install the system on a stable, level surface.

- The system may not operate properly.

• Install the system in a place with appropriate
moisture and temperature levels.

- Avoid installing the system in a place with high

(over 40°C) or low (under 0°C) temperature.

• The system can be damaged from a strong
impact or vibration. Avoid throwing objects within
the vicinity of the system.

• Avoid direct sunlight or any heating appliances.

- Recommended operating temperature is over

0°C (32°F).

• Ventilate the air inside the system operation room,
and tighten the system cover firmly.

- System breakdown may be caused by an

inappropriate environment.

It is recommended to use AVR (Automatic Voltage

Regulator) for a stable power supply.
It is recommended to coil the core-ferrite around
the connector of the system to avoid electromag­netic interference.

• The outlet must be placed on the ground.

• If there is strange sound or smell, unplug the
power cable immediately and contact the service
center.

- This may cause fire or electric shock.

• In order to maintain stable system performance,
have your system checked regularly by the ser­vice center.

- LG Electronics is not held responsible for sys-

tem breakdown caused by user mishandling.

- There is a risk of explosion if a battery is

replaced by an incorrect type. Dispose of used
batteries according to the instructions.

• Do not overturn the product during use.

5

Contents

INTRODUCTION .................................. 7

Features ................................................................7

Front Panel ...........................................................8

Accessories ..........................................................9

Rear Panel .........................................................10

Remote Control ...................................................11

HOOKUP AND SETTINGS ................ 12

Basic Connection Overview ................................12

Connecting the RS-422/485 Device ...................13

Connecting the USB Device ...............................14

Network Connection ...........................................14

Connecting the RS-232C Port ............................14

Connecting CONSOLE .......................................14

Concerning the Internal Hard Disk Drive ............15

Installing or Replacing the Hard Disk Drive .......15

System Operation ...............................................20

System Shutdown ...............................................20

Selecting the main monitor type .........................21

General Explanation of the LiveScreen on the

Main Monitor .................................................22

Selecting Live Screen Mode ..............................23

PTZ Camera Control ..........................................24

Viewing System Information ..............................26

Viewing the System Log List .............................26

Menu Configuration ............................................27

Camera Settings .................................................28

Schedule Settings ...............................................30

Display Settings ..................................................33

Event Settings .....................................................34

Network Settings .................................................35

System Settings ..................................................38

SEARCH AND PLAYBACK .............. 44

PLAYBACK .........................................................44

SEARCH .............................................................45

Functions Available During Playback .................48

EXPORT ............................................................49

CLIENT PROGRAM ........................... 50

PC Requirements ...............................................50

Client Program Installation .................................50

Main Screen of DVR Client Program ..................52

Live Mode ...........................................................53

Search Mode ......................................................56

Remote Setup Mode ...........................................57

Remote Export Settings ......................................63

ADDITIONAL PROGRAMS ............... 64

Emergency Agent Program ................................64

Main Screen of Emergency Agent ......................64

Export Viewer Program ......................................65

Web Viewer Program .........................................66

REFERENCE ..................................... 68

Troubleshooting ..................................................68

Recommended Devices ......................................71

Time zones .........................................................72

Factory Default Configuration Settings ...............73

Recording Time Table (250GB HDD) .................76

Specifications ......................................................79

RECORDING ...................................... 43

Instant Recording ................................................43

6

INTRODUCTION

Features

• Stable embedded Linux operating system.

• Journal filing system for HDD file recovery

following power recovery.

• Small file sizes with MPEG-4 compression.

• Internal storage expandable to 2TB. (Expandable

if new high capacity HDD is launched)

• NTSC and PAL selectable video format.

• Full realtime recording.

- Up to 480IPS@352 X 240: LDV-S504 NTSC

- Up to 400IPS@352 X 288: LDV-S504 PAL

- Up to 240IPS@352 X 240: LDV-S503 NTSC

- Up to 200IPS@352 X 288: LDV-S503 PAL

• Various recording resolutions and quality levels.

- D1(704x480), Half D1(704x240), CIF(352x240)
: NTSC

- D1(704x576), Half D1(704x288), CIF(352x288)
: PAL.

- 5 step quality level (Highest, High, Standard,
Low, Lowest).

• Easy operation using various user interface &

user friendly GUI.

- Optical mouse, Full function IR remote control­ler, Jog/Shuttle

• Powerful multiplex function.

- Simultaneous live display, recording, playback,
network transmission, back-up.

• Various search function.

- Date/time search (calender search), event
search, bookmark search, smart search.

• Event data protection by event partition recording.

• Pre-alarm recording (Up to 1minute).

• Motion event recording and preview test function

of motion sensitivity.

• Recording image rate & quality adjustment per

individual camera.

• Powerful record scheduling.

• Instant playback in surveillance mode.

• POP(picture over picture) playback.

- Viewing live and playback video simultaneously.

• Perfect audio/video synchronization.

• Automatic backup by schedule.

• Image authentication (Watermark).

• Three USB 2.0 ports for backup interface.

• Setup configuration export/import with

USB memory stick.

• Easy system S/W update with USB memory stick

or network.

• Clients S/W can manage max 100 DVR servers.

• Max five clients can access one DVR server

simultaneously.

• Network bandwidth throttle.

- Automatically adjust a bandwidth according to
network speed status of unit.

• Remote alarm notification via client software

or E-mail.

• Time and date sync from NTP server.

• Daylight saving mode.

• Covert camera protection.

• Back-up CD auto run.

• User management (User level control).

• PTZ Control.

- For more details see page 71.

- Dome camera telemetry control (Dome OSD
control).

INTRODUCTION

Model LDV-S504 (16 Channel) is used for the description, operation and details provided in this
operating guide.

7

Front Panel

x LDV-S504

ab c defgh

ijklmno

x LDV-S503

ab c defgh

ijklmno

a LAN Indicator

Lights when the network is connected.

HDD Indicator

Blinks when the HDD is accessed.

ALARM Indicator

Lights when the alarm out is in progress.

b LOCK

Displays the lock menu to change the user type
or disable the system operation.

MAIN

Display the MAIN menu to set the screen mode
to full, 4, 6, 8, 9 or 16 screens. Set the video
output signal to VGA mode.

SPOT

Enter SPOT mode to allow spot monitor control.
Set the video output signal to MAIN-OUT and
S-VIDEO mode.

SHIFT

If you use the Sub-function of the channel but­ton, the button is activated.

c Channel Buttons

You can input a number with channel buttons.
You can also use the channel buttons for sub­function with SHIFT button (11~16 buttons of 8
channel DVR are used for subfunction without
SHIFT button.). The LED in the button indicates
the status as follows:

- Off: No video input signal.

- Green: The current status is for live mode.

- Red: Recording mode.
Blinks when an event occurs.

(3) FOCUS - / (4) FOCUS +

Adjusts focus position.

(5) OSD

Accesses or removes the System Control Bar
(OSD).

8

(6) INFO

Displays or removes system information.

(7) IRIS - / (8) IRIS +

Adjust iris position.

(9) ALM.OFF

Cancels alarm activation and returns the system
to the condition before the alarm was activated.

(10/0) LOG

Displays or removes the System Log List.

(11) SET

Registers the PTZ camera's preset position.

(12) CLEAR

Deletes a memorized preset position.

(13) COPY

Copies the recording data to an external device.

(14) MARK

Sets the mark point for recording search.

(15) MOVE

Moves the camera to the preset position.

(16) TOUR

Tours all registered preset positions in the cam­era.

d PTZ

Switches this unit to PTZ mode to control the
PTZ camera connected.

e Arrow Buttons (b B v V)

Select or move between the menu options.

ENTER

Confirms menu selections.

f SETUP/ESC

Displays the setup menu or cancels operation
on the setup menus.

g JOG Dial

Allows a forward or reverse frame search.
In pause mode, plays recorded images
frame by frame through rotation. Increases or
decreases the options value.

h Shuttle Ring

Fast forward or reverse picture search when the
dial is rotated.

i 1 Power

Turns DVR on or off.
Press and hold for more than 2 seconds to turn
on or off.

j Playback Control Buttons

- X: Pauses playback.

- m/c/.: Search the recorded images in
reverse or skip the recorded images.

- bB: Playback or reverse playback of
recorded images.

- M/C/>: Forward search the recorded
images or skip the recorded images.

- x: Stops playback.

k Remote Sensor

Point the remote control here.

l ZOOM + / -

Zooms in/out on live images or on playback
window.

m SEARCH

Displays the search menu.

n REC

Starts or stops recording.

o USB Port

Connect an external USB device for backup or
playback.

INTRODUCTION

Accessories

Software
Install CD

IDE Cable

Extension HDD
Power Cable

AAA

Rack Mount
Bracket

AAA

Note: The accessories may be different depending on models.

Power Plug

Mouse

AAA Type
Battery



Remote
Control

Terminal
Blocks

Screws

9

Rear Panel

x LDV-S504

efghijklmno pqr

x LDV-S503

abcd

SENSOR-IN

abcd

SENSOR-IN

efghijklmno pqr

a VIDEO INPUT

Connect the cameraʼs video output to these
BNC connectors.

b SENSOR-IN Terminals

Input terminals for alarm signal.

c AUDIO OUT

Connect the audio input signal of an external
device.

AUDIO INPUT

d

Connect the audio output of an external device.

e RS-422/485 Terminals

Connect RS422/485 compatible cameras.

f RS-232C Connector

Used to connect to a host device equipped with
RS-232C connector (such as a personal com­puter). This unit can be controlled from other
devices via this connector.

g LOOP OUT

The signal from VIDEO INPUT connector is
looped out to this connector.

h CONSOLE

Used to connect to a host device equipped with
RS-232C connector (such as a personal com­puter). This unit can be controlled from other
devices via this connector.

i LAN Port

Connect the ethernet 10/100Mbps network
cable for controlling this unit via a PC network.

j SPOT-OUT (BNC Type Connector)

Connect to spot monitor or display device.

k MAIN-OUT (BNC Type Connector)

Connect to main monitor or display device.

l S-VIDEO

Connect an S-Video compatible monitor.
The image will be the same as when the
monitor is connected to the MAIN-OUT jack.

m VGA

Connect a VGA monitor.

n USB Ports

Connect an optional extension USB device.

o ALARM-OUT Terminals

Output terminals for alarm signal.

p Cooling Fan
q Power Cord Inlet (AC IN)

Connect the power plug.

r Power Switch

Turns the main power on and off.

10

Remote Control

POWER (1)

Turns DVR on or off.

LOCK

Displays the lock menu to change
user type or disable system
operation.

ID

Set the appropriate DVR system
ID to operate via the IR Remote
Controller when using the multiple
DVR.
Press the ID button then press the
number button within 2 seconds to
select the system ID of the DVR.
If you set the system ID to “0”, you
can control multiple DVR at the
same time.

MAIN

Displays the MAIN menu to set
the screen mode to full, 4, 6, 8, 9
or 16 screens.

SPOT

Enter SPOT mode to allow spot
monitor control.

ALM.OFF

Cancels alarm activation and
returns the system to the condition
before the alarm was activated.

OSD

Accesses or removes the system
control bar (OSD).

SETUP/ESC

Displays the setup menu or can­cels operation of the setup menu.

Arrow Buttons (b B v V)

Selects or moves between the
menu options.

ENTER

Confirms menu selections.

COPY

Copies the recording data to an
external device.

SEARCH

Displays the search menu.

MARK

Sets the mark point for record­ing search. You can set the mark
point during the single channel
playback of recorded data.

PAUSE (X)

Pauses playback.

STOP(x)

Stops playback.

REC (z)

Starts or stops recording.

m/c/.

Searches the recorded images
in reverse or skips the recorded
images.

bB
Playback or reverse playback of
recorded images.

M/C/>

Forward searches the recorded
images or skips the recorded
images.

Number Buttons (0,1-9)

To select the PTZ preset number,
ID, or channel.

INFO

Displays or removes the system
information window.

LOG

Displays or removes the System
Log List window.

PTZ

Switches this unit to PTZ mode to
control the connected PTZ camera.

TOUR

Tours all registered preset posi­tions in the camera.

ZOOM + / -

Zooms in/out on the playback
window.

FOCUS + / -

Adjusts the focus of a camera.

IRIS + / -

Adjusts the iris of a camera.

PRESET

- SET: Registers the PTZ
camera's preset positions.

- CLEAR: Deletes a memorized
preset position.

- MOVE: Moves the camera to
the preset position.

F1

This button is not available.

INTRODUCTION

11

HOOKUP AND SETTINGS

Precautions

• Depending on the camera and other equipment there are various ways to connect the
unit. Please refer to the camera manual or manuals for other devices as necessary for
additional connection information.

• Be sure to switch off the camera before installation and connection.

Basic Connection Overview

Connect the Monitor, DVR, VCR, or others.

Connect PTZ cameras,
DVRs or keypads (optional).

Connect network cable

for client control.

Connect the coaxial-type cameras

Connect the alarm (relay)

Connect audio
(line input)

For audio
amplifier

Connect
power code

Connect alarm sensors.

Connect mouse for

Connect

BNC type

spot monitor.

Connect

BNC type

monitor.

12

use with this operating
system or USB device
for backup, copy or
others.

Connect VGA monitor.
(Default output)

Connecting the RS-422/485
Device

This DVR has two data terminals.
Use this port to connect PTZ cameras, DVRs or key­pads (optional).

Rear of the DVR

Connecting Sensor Input and
Alarm Output

Alarm terminals are used to connect the alarm devic­es such as sensors, door switches, etc.

Sensor Input

You can connect up to 16 alarm sensors (LDV-S503:
8 alarm sensors).
Each alarm sensor should be connected with G
(GND). The signal state is adjustable to N/O (Normal
Open) or N/C (Normal Close) through the setup
menu.

Rear of the DVR

SETTINGS

HOOKUP AND

TX-

TX+

RS-422/485 Terminal Description

TX - (DATA -) Data Transmission

TX + (DATA +) Data Transmission

RX - (DATA -) Data Reception

RX + (DATA +) Data Reception

GND Shield

Connecting the PTZ camera

Connecting the PTZ serial communication lines to the
RS-422/485 terminal.

Notes:

• When connecting lines, connect the TX - of the

DVR to RX - of the PTZ unit and TX + of the DVR
to RX + of the PTZ unit correctly.

• Recommended initial data are 9600 Baud Rate,
8 Data bits, 1 Stop bit and No parity.

• When connecting PTZ cameras to DVRs it is
necessary to set the setup menu for this unit
according to the RS-485 settings of the camera
and DVRs.

Connecting the LKD1000 controller

Connecting the LKD1000 controller to control the
DVR. (Refer to the manuals of the LKD1000 control­ler for more details.).

SENSOR-IN

Terminal No. Description

1 Sensor Input 1
2 Sensor Input 2
3 Sensor Input 3
4 Sensor Input 4

G Ground

5 Sensor Input 5
6 Sensor Input 6
7 Sensor Input 7
8 Sensor Input 8

G Ground

9 Sensor Input 9
10 Sensor Input 10
11 Sensor Input 11
12 Sensor Input 12

G Ground
13 Sensor Input 13
14 Sensor Input 14
15 Sensor Input 15
16 Sensor Input 16

G Ground

13

Alarm Output

Connect up to 8 separate alarms (LDV-S503: 4 sepa­rate alarms) to the alarm output.

Alarm signal output at an event occurrence.

Rear of the DVR

Note:

The internal switching relays are rated for 0.5A at
125V AC or 1A at 30V DC. If the electric current is
higher than that the unit can be damaged.

Connecting the USB Device

USB Memory Device

Insert the memory device into the USB port. The sys­tem automatically recognizes the device.

Using a USB memory device the system S/W can be
easily upgraded.

USB Backup Device

Connect the USB cable of the USB backup device to
the USB port on the rear panel of the unit.

(Example: CD/DVD-R/RW drive, HDD or other exter­nal storage.)

Mouse

Connect the USB mouse for function control of the
unit.

Terminal No. Description

1 Alarm output 1
2 Alarm output 2
3 Alarm output 3
4 Alarm output 4

G Ground

5 Alarm output 5
6 Alarm output 6
7 Alarm output 7
8 Alarm output 8

G Ground

Network Connection

LAN Connection

Connect the LAN port to an available 10/100 base-T
port with a straight ethernet cable (not supplied).
The NET indicator on the front panel will be lit.

Automatic Network Configuration

The DVR can automatically obtain and configure the
network interface via DHCP. (see page 35)

Manually Configure Network

The DVR may be manually configured by assigning
an IP address, subnet mask, gateway, DNS. (see
page 35)

Connecting the RS-232C Port

The RS-232C is used for communication with a con­nected PC. This terminal is compliant with the RS­232C standard.

Connecting CONSOLE

Used to connect to a host device equipped with an
RS-232C connector (such as a personal computer).
This unit can be controlled from other devices via this
connector.

14

Concerning the Internal Hard
Disk Drive

The internal hard disk drive (HDD) is a fragile piece
of equipment. Please follow the guidelines below
when using the DVR to protect against possible HDD
failure.
We recommend that you back up your important
recordings onto an external backup device in order to
prevent accidental loss.

Make sure that the power is turned OFF when attach­ing or removing the HDD.

• Do not move the DVR while the power is on.

• Do not use the DVR in excessively hot or humid
places, or in places that may be subject to sudden
changes in temperature. Sudden changes in tem­perature can cause condensation to form inside the
DVR. This can be a cause of HDD failure.

• While the DVR is switched on, do not unplug from
the wall socket or switch the electricity off from the
breaker switch.

• If thereʼs a power failure while the DVR is on there
is a chance that some data on the HDD will be lost.

• Do not drop the HDD. Also do not put the metallic
object such as coins or screwdrivers into the HDD
tray.

• When a power failure occurs during recording,
avoid adding, replacing or transporting the HDD as
the recorded data may be erased. In this case, turn
the power back on to boot up the unit normally with
the HDD that was being used at the time of the
power failure attached. Then add, replace, or trans­port the HDD.

• The HDD is very delicate. Handle the HDD with
care and follow the precautions below because
even a small shock may damage the internal com­ponents of the HDD.

- Do not place the HDD on a desk or a table

directly. Put a thick cushion under the HDD
because even a small shock may damage the
internal components of the HDD.

- Do not use an electric screwdriver. Vibrations

and shocks caused by an electric screwdriver
may damage the internal components of the
HDD.

- When replacing the HDD, do not knock the HDD

with other components such as another HDD and
the HDD tray.

- Do not knock the HDD with tools such as a driver

when replacing the HDD.

• Protect the hard disk drives from static electricity.

Installing or Replacing the Hard
Disk Drive

Installing the Hard Disk Drive

You can install up to 4 HDDs.

However, since the product contains many parts
which may incur electric shocks, accidents or prod­uct breakdown, and because improper installation or
setup may disturb HDD recognition or normal product
operation, you should consult with an expert from the
store where the product was purchased.

Turn the power of the unit off and detach the power

plug from the outlet.

1. Remove the fixing screws on the left/right side
and rear panel.

2. Detach the top case by sliding it after removing
the screws.

3. Detach the front panel as shown below.

SETTINGS

HOOKUP AND

15

4. Remove the screws and detach the hard disk
mounting brackets from the unit.

• When installing 3 HDDs.

A Attach the first HDD onto the upper side of

the primary HDD mounting bracket and set
the primary master HDD.

B Attach the second HDD onto the lower side

of the primary HDD mounting bracket and
set the primary slave HDD.

C Attach the third HDD onto the upper side of

the secondary HDD mounting bracket and
set the secondary master HDD.

A

Primary HDD
mounting bracket

Secondary HDD
mounting bracket

5. Attach the HDD onto the hard disk mounting
brackets with four screws as shown below.

• When installing 1 HDD.

: Attach the HDD onto the upper side of the
Primary HDD mounting bracket and set the
Primary Master HDD.

• When installing 2 HDDs.

A Attach one of the HDDs onto the upper side

of the primary HDD mounting bracket and
set the primary master HDD.

B Attach the other HDD onto the lower side of

the primary HDD mounting bracket and set
the primary slave HDD.

B

C

• When installing 4 HDDs.

A Attach the first HDD onto the upper side of

the primary HDD mounting bracket and set
the primary master HDD.

B Attach the second HDD onto the lower side

of the primary HDD mounting bracket and
set the primary slave HDD.

C Attach the third HDD onto the upper side of

the secondary HDD mounting bracket and
set the secondary master HDD.

D Attach the fourth HDD onto the lower side of

the secondary HDD mounting bracket and
set the secondary slave HDD.

A

A

B

C

B

D

16

6. Connect the HDD power cable extension.

• When installing 3 HDDs.
Connect the IDE cable to the IDE terminal of
HDD using the Primary and Secondary IDE
cables.

7. Connect the IDE cable.
You must connect the IDE cable as shown below.

• When installing 1 or 2 HDDs.

Connect the IDE cable to the IDE terminal of
the HDD using the primary IDE cable.

To Primary

Master HDD

To Primary

Master HDD

To Primary

Slave HDD

To Secondary

Master HDD

Secondary IDE cable

Primary IDE cable

• When installing 4 HDDs.
Connect the IDE cable to the IDE terminal of
the HDD using the primary and secondary IDE
cables.

To Primary

Master HDD

Primary IDE cable

SETTINGS

HOOKUP AND

To Primary

Master HDD

To Primary

Slave HDD

Primary IDE cable

Primary IDE cable

To Primary
Slave HDD

To Secondary

Master HDD

To Secondary

Slave HDD

Secondary IDE cable

17

8. Attach the hard disk mounting brackets with the
screws.

9. Connect the power cable.

Extension

HDD power cable.

Power cable for
power supply.

10. Connect the IDE cable to the IDE connector on
the main board. You must connect the IDE cable
as shown below.

Replacing the Hard Disk Drive

Turn the power of the unit off and detach the power
plug from the outlet.

1. Follow steps 1-3 described in “Installing the Hard
Disk Drive”.

2. Remove the screws and detach the hard disk
mounting brackets from the unit.

Primary IDE cable

IDE1 (Primary

HDD connector)

IDE2 (Secondary
HDD connector)

Secondary IDE cable

11. Assemble the front panel and top case.

12. Fix the screws.

13. After installing the HDD, you must format the
HDD using the setup menu (See page 40).

Notes:

• When you add the new HDD, do not change the

position or jump setting of the HDD.
It may delete the current data and cause a mal­function.

• You must connect the primary IDE cable to the

primary IDE connector on the main board and the
secondary IDE cable to the secondary IDE connec­tor on the main board.

3. Remove the connector from the HDD.

4. Remove the screws from the hard disk drive on the
left/right side of the hard disk the mounting bracket.

18

5. Remove the HDD from the hard disk mounting
bracket.

6. Install the new HDD in the reverse order to when
replacing the hard disk drive.

7. After replacing the hard disk drive, insert the
power plug into the outlet and turn the power of
the unit on.

Notes:

• When you install or replace the HDDs to the
hard disk mounting bracket, you must set the
HDD jumper to slave or master.
You must install the HDD as shown below.

- Upper sides: Set the master HDD.

- Lower sides: Set the slave HDD.

• How and where to set the HDD jumper depends
on the manufacturer or model specification.
Therefore, carefully read the instructions printed
on top of the product or in the manual enclosed
with the product before installing the jumper.

- If the jumper pin settings are identical with

each other in terms of priority, either HDD may
not be detected in the DVR or malfunction
may occur.

• Make sure that each of the IDE cables is con­nected to the connector housing through its holes.

• Do not stack them nor keep them upright.

• Do not use an electric screwdriver to fix them.

Recommended HDD

The following HDD has been tested and compatibility
is ensured. When you attach multiple HDDs use the
recommended HDDs.

Maker RPM Capacity Interface Model No.

Hitachi

Seagate

7,200 80 GB

7,200 160 GB HDT722516DLAT80

7,200 250 GB HDT722525DLAT80

7,200 320 GB HDT725032VLAT80

7,200 500 GB HDT725050VLAT80

7,200 200 GB

7,200 250 GB ST3250824ACE

7,200 300 GB ST3300822ACE

7,200 500 GB ST3500841ACE

Ultra

ATA133

Ultra

ATA100

HDS728080PLAT20

ST3200827ACE

SETTINGS

HOOKUP AND

19

System Operation

1. Press and hold 1 (POWER) button until the beep

sounds to turn on the unit. System booting will
commence. The LG logo image will be displayed
on the main monitor during the system booting.

2. When the booting is completed the login window
will be displayed.
Select a user ID by using the mouse or arrow and
the ENTER button on the remote control or front
panel.

- ADMINISTRATOR: Unlimited operation of the

unit.

- Power User: Use of the limited functions of the

system. (The setup configuration is not
allowed to change.)

- Normal User: Use of the limited functions of

the system. (Split monitor and live image view
are available.)

3. Enter the password by using the virtual keyboard.
(Initial password is “000000”.)

4. Press LOCK or click the OK(LOCK) icon.
You can see the live screen and operate the sys­tem.

Notes:

• You are not allowed to connect the VGA moni­tor and the composite monitor simultaneously.
Consequently, the user is obliged to choose either
the composite monitor or the VGA monitor. When
set to composite monitor there is no VGA output.
When set to VGA monitor there is no composite
output. SPOT-OUT is unaffected by the monitor
setting.

• This DVR is based on a VGA monitor using OSD.
We recommend to using the VGA monitor with
this unit. If you use a composite monitor, the OSD
quality may lower to read it.

• User access rights

User Level Administrator

View

Live Video

Alarm Off YES YES NO

PTZ YES YES NO

Instant Record YES YES NO

Export YES YES NO

Search/Play YES YES NO

Setup YES NO NO

Shut Down YES NO NO

YES YES YES

Power

User

Normal

User

System Shutdown

1. First, you must stop playback and exit the setup
menu.

In playback, press STOP.

2. Press and hold 1 (POWER) button until the beep
sounds and the logout window will be displayed.

3. Enter the password by using the virtual keyboard.

4. Press LOCK or click the OK(LOCK) icon.
The system will shutdown.

20

Selecting the main monitor type

You can select the main monitor type to display the
main screen on the power on condition.

Using the VGA Monitor

1. Connect the VGA monitor to the VGA jack on the
rear of the DVR.

2. Turn on the VGA monitor.

3. Press and hold the MAIN button on the front
panel until the beep sounds to display the main
screen. The DVR will restart and then the VGA
monitor is set as a main monitor.

Note:

You can select the monitor type by using the MAIN or
SPOT button at anytime. If you change the monitor
type, the system will be rebooted automatically.

SETTINGS

HOOKUP AND

CCTV (Composite Video Type) Monitor

1. Connect the CCTV monitor to the MAIN-OUT or
S-VIDEO jack on the rear of the DVR.

2. Turn on the CCTV monitor.

3. Press and hold the SPOT button on the front
panel until the beep sounds to display the main
screen. The DVR will restart and then the CCTV
monitor is set as a main monitor.

21

General Explanation of the Live
Screen on the Main Monitor

Main Monitor Screen

ab c d e f

f System Control Bar

Displays the current date
and time.

Displays the setup menu.

Displays the search menu.

Displays the PTZ
remote control window.

- N (Normal partition):
Used size/total size.

- E (Event partition):
Used size/total size.

Display/hide playback
control bar.

Pause playback.

Jump to the beginning
of the current data
recorded on the same
date.

a Channel Number

Displays the channel number.

b Channel Name

Displays the edited channel name.

c Camera Status Icon

PTZ camera icon

•
Displays the PTZ camera status.

Input audio icon

•
Displays the input audio status.

Recording status icon

•
Displays the recording status.

- Green “C” indicates continuous recording.

- Green “I” indicates Instant recording.

- Red “S” indicates sensor triggered

recording.

- Blue “M” indicates motion detection

recording.

- White “N” indicates the channel is not

being recorded.

Displays the screen divi­sion selection window for
the main monitor.

Displays the screen divi­sion selection window for
the spot monitor.

Displays the lock menu to
change the user type or
disable system operation.

Displays the system log
list window.

Turns the alarm off.

Displays the system
information window.

Displays the remaining
HDD status.

Select the required
scanning speed.

Jump to the last min­ute of the current data
recorded on the same
date.

Stop playback.

Display playback status.

Enlarge/reduce the
playback window.

Click at a desired point
to be marked during
playback. Up to 15
points can be marked.

Display copy(export)
menu.

d Selected Channel

Displays the selected channel with red box.

e Live Screen

Displays the current surveillance live screen.

22

Note:

Use OSD with the SHIFT button on the front panel
or click the right button on the mouse to display /
remove the system control bar displayed on-screen.

Selecting Live Screen Mode

Main Monitor

You can select the live screen mode to display a full,
4-split, 6-split, 8-split, 9-split or 16-split screens on
the main monitor.

1. Press MAIN or click the MAIN icon in the system
control bar.
Screen mode select menu of main monitor is dis­played on the main monitor.

2. Select screen mode.

Selected Main Channel

Screen mode

Selected split

mode

Sequence

Spot Monitor

You can select the live screen mode to full or 4-split
screens on the spot monitor.

1. Press SPOT or Click the SPOT icon in the system
control bar.
Screen mode select menu of spot monitor is dis­played on the main monitor.

2. Select screen mode.

Selected spot channel

Selected split

mode

Screen mode

Sequence

Channel buttons

SETTINGS

HOOKUP AND

Channel Buttons

- Channel Number: Press the 1 to 16 channel

button to see the current surveillance images
in selected live screens on the main monitor.

- Full Screen Mode: When you see the selected

channel on the full screen.

- 4, 6, 8, 9 and 16 Split Mode: Displays select-

ed split screens on the main monitor.

- Sequence: View all channels in sequence.

3. Select [OK (MAIN)] and press ENTER to confirm
your selection.

Note:

To display the screen you desire to watch in full
screen mode, double click the desired channel.

- Channel Number: Press the 1 to 16 channel but-

ton to see the current surveillance image on the
spot monitor.

- Full Screen Mode: When you see the selected

channel on the full screen.

- 4 Split Mode: Displays 4 split screens on the

spot monitor.

- Sequence: Views the all channels in sequence.

3. Select [OK (SPOT)] and press ENTER to confirm
your selection.

23

PTZ Camera Control

You can control the cameras connected via the data
port of RS-422/485 terminal. You must set the con­figuration between the PTZ camera and the DVR.

1. Select the PTZ camera channel on the main mon­itor you want to control.

2. Press PTZ or Click the PTZ icon in the system
control bar.
Virtual PTZ remote control is displayed on the
main monitor.

3. Use each item to control the PTZ camera.

a

b

c

d
e

f

g

a Exit

Remove the PTZ virtual remote control.

b v/V/b/B

Use to pan/tilt the camera.

§

Confirm the preset position.

c ZOOM + / -

To adjust the camera zoom.

d FOCUS + / -

To manually adjust the focus of a camera.

e IRIS + / -

To manually adjust the iris of a camera.

f Displays the Selected Preset Number
g Number Buttons

To input the preset number.

h SET

To register preset positions.

i MOVE

To move the camera to the preset position.

j CLEAR

To delete a memorized preset position.

k TOUR

To start a preset tour.

l SETUP

To displays the setup menu of the PTZ camera.

h
i

j
k

l

24