Lg LDT7797ST Dimension Guide
PREPARING WATER SUPPLY CONNECTION
•
Make sure the house water supply is turned off before connecting the
dishwasher water lines.
•
Connect the dishwasher to a hot water supply with a temperature range between
120 °F (49 °C) and 149 °F (65
°C). This temperature range
provides the best washing results
and shortest cycle time. To
prevent damage to dishes, the
temperature should not exceed
149 °F (65 °C).
•
When connecting the dishwasher
water line, sealing tape or
compound should be used on pipe
threads to avoid leaks. Tape or
compound should not be used on
compression ttings.
•
The water supply tube must be
located in the left side channel.
PREPARING CABINET OPENING
•
This dishwasher is designed to t a standard dishwasher opening. An
opening may be needed on both sides to route plumbing and electrical
connections.
•
Select a location as close to the sink as possible for easy connections to water and
drain lines.
•
To ensure proper drainage, install the
dishwasher no more than 12 ft. from
the sink.
•
If installing the dishwasher in a corner,
leave a minimum of 2" between the
dishwasher and the adjacent wall.
•
To allow for proper clearance of
plumbing and electrical, use the
template included with the literature
to determine the clearance on the side
of the cabinet where the cabinet meets
the back wall. Using a 2 1/2" diameter
hole saw, drill a hole in the target area
as shown on the template.
▲
! WARNING
Don't use existing holes unless they are in the target area. Otherwise, the water supply
and drain hose may be damaged by being crushed or kinked.
▲
! CAUTION
Failure to properly locate the hole for the water and drain lines may prevent the
dishwasher from installing ush with the cabinets and could result in kinked or
damaged lines. Installation damage is not covered by the warranty, and leaks caused by
improper installation may result in property damage.
PREPARING ELECTRICAL WIRING
•
Operate this appliance with the correct voltage as shown in your
User Manual and on the rating plate. Connect it to a dedicated,
properly grounded branch circuit which is protected by a time
delay fuse. Connect
the appliance using
3-wires, including a
ground wire.
•
If an outlet and other
power connector are
used, it should be in
an accessible location
adjacent to and not
behind the dishwasher
and within 4 ft. of the
dishwasher's side.
•
The wiring must be
grounded properly.
If in doubt, have it
checked by a qualied
electrician. Do not connect any other appliance to the same outlet.
•
Route the wiring.
•
Make sure the electrical cable is oriented in the right side channel.
▲
! WARNING
•
For personal safety, remove house fuse or open circuit breaker
before installation.
•
Do not use an extension cable or adapter with this dishwasher
•
If you nd any damage to the dishwasher, contact your retailer or
contractor.
4 /2" - 6”
1
Electrical cable
NOTE
Use new hoses when connecting to the water supply. Do not reuse old hoses.
2
/6" - 7 /4"
13
Water supply line
LDT7797*
QUICK INSTALL &
CLEARANCES
For full installation directions/clearances
please refer to the corresponding
User Manual and Installation Guide.
DIMENSIONS / CLEARANCES / WEIGHT
Product Dimensions (in) (W x H x D) 23.75" x 33.6" x 24.6"
Product Weight (lbs) 81.6 lbs
Depth with Door Closed with Handle (in) 27-1/8"
Depth with Door Open (in) 50.5"
Clearances (W x H x D) 24" x 33.5" x 24"
Carton Dimensions (in) (W x H x D) 28" x 34.7" x 29.6"
Shipping Weight with Carton (lbs) 94.8 lbs
POWER RATINGS
ENERGY STAR® Qualied Yes
CEE Tier 1
Energy Use (kWh/Year) 258 kWh
Water Factor (WF) 2.8
LG Brand_Dishwashers Fin_1.indd 8 8/21/17 4:05 PM
Loading...