DISHWASHER
OWNER’S MANUAL
MODEL : LD-2263W(S,M,L,T)H
LD-2263W(S,M,L,T)HB
LD-2263W(S,M,L,T)HU
Please read this manual carefully before operating your dishwasher. Retain it for future reference.
CONTENTS
SAFETY AND CAUTION |
3 |
|
|
INSTALLATION INSTRUCTIONS |
5 |
|
|
PARTS NAME |
9 |
|
|
FUNCTION OF CONTROL BUTTON |
10 |
|
|
HOW TO USE AND OPERATE |
12 |
|
|
OPERATING SEQUENCE |
19 |
|
|
PROGRAM |
20 |
|
|
USER MAINTENANCE INSTRUCTIONS |
21 |
|
|
TROUBLE SHOOTING GUIDE |
22 |
|
|
SPECIFICATION |
|
|
|
SAFETY AND CAUTION
IMPORTANT SAFETY INSTRUCTIONS
WARNING - When using your dishwasher, follow basic precautions, including the following:
•Please read this manual carefully before using the dishwasher for the first time.
•This manual contains very important notes regarding the installation, use and maintenance of your dishwasher.
•The manufacturer can not be responsible for problems caused by ignoring these safety and caution instructions.
•This dishwasher is designed for normal household use.
•Do not use the dishwasher for industrial and commercial use, or other purpose.
•The appliance is not intended for use by young children or infirm persons without supervision.
During installation
•Electrical connection must be in accordance with the rating label.
•Electrical safety is only guaranteed when the earth system of your house is in accordance with the related local regulations.(Do not use an extension cable or cord.)
•If the hot water exceeds 65ºC, adjust the water heater setting. If the hot water temperature can not be maintained below 65ºC, the dishwasher must be connected to cold water.
•If power supply cord is damaged, it must only be replaced by the manufacturer or its service agent or a similar qualified person in order to avoid a hazard.
•This appliance must be positioned so that the plug is accessible.
•The appliance is to be connected to the water mains using new hose-sets and that old hose-sets should not be reused.
During use
•Only suitable household utensils should be placed in the dishwasher.
(Please avoid utensils; that are nonheartresistant, metal decorated, etc.)
•Do not use any kinds of solvent in your dishwasher. They may cause an explosion or fire.
•Do not spray water on the appliance.
It may cause the failure of electric parts or electric shock.
•Do not push down or sit on the inner door when the door opened. It may cause the deformation or failure of your dishwasher.
•Do not use the detergent for hand washing. The detergent for dishwasher should be used for normal operation.
•This appliance is fitted with a safety function that automatically stops the operation of the dishwasher when it is exposed to heavy disturbance on its mains.
•Dishwasher detergents are strongly alkaline. They can be extremely dangerous if swallowed. Avoid contact with skin and eyes and keep children away from the dishwasher when the door is open.
Check that the detergent receptacle is empty after completion of the wash cycle.
Child Safety
•Controls may be locked using “Child Lock” mode to prevent from starting dishwasher accidentally.
•Keep children away from detergents and rinse-aids.
•Do not allow children to operate the dishwasher.
•Young children should be supervised to ensure that they do not play with the appliance.
3
SAFETY AND CAUTION
concerning the Power Cord
recommend they be placed upon a dedicated circuit; that is, a single outlet circuit which that appliance and has no additional outlets or branch circuits. Check the specification page
manual to be certain.
wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could shock or fire. Periodically examine the cord of your appliance, and if its appearance
or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced replacement part by an authorized servicer.
power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits
.
CAUTION |
The instructions shall state the substance of the following : |
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of a malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is installed and grounded in accordance with all local codes and ordinances.
WARNING - Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service representative if you are in doubt whether the appliance is properly grounded. Do not modify the plug provided with the appliance; if it will not fit the outlet have a proper outlet installed by a qualified electrician.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.
4.For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.
4
INSTALLATION INSTRUCTIONS
WARNING
Any electrical work required to install this appliance should be carried out by a qualified electrician or competent person. Any plumbing work required to install this appliance should be carried out by a qualified plumber or competent person.
Step 1 :
PREPARE CUPBOARD OPENING
1This dishwasher is designed to fit to the size shown as below.
2Select a location as close to sink as possible for easy connections to water and drain lines.
3The dishwasher should not be installed more than 3 meters from sink for proper drainage.
4If dishwasher is to be installed in a corner, a minimum 5cm of space is required between the washer and an adjacent cabinet or a wall.
Unit:mm |
If bare chipboard is adjacent to or above the dishwasher, it should be sealed with a waterproofing paint or sealant to prevent swelling due to steam
Step 2 :
PREPARE ELECTRICAL WIRING
CAUTION
For personal safety, remove house fuse or open circuit breaker before installation. Do not use an extension cord or adapter plug with this appliance. Electrical and grounding connections must comply with the national electrical code/provincial and municipal code and/or other local codes.
1This appliance must be supplied with correct rating voltage and hertz as shown on instruction manual, and connected to an individual, properly grounded branch circuit, protected by minimum 15 amp circuit breaker or time delay fuse. Wiring must be 2 wires with ground.
2The power plug must be in a accessible location adjacent to and not behind the dishwasher and within 1.2 meters of the dishwasher side.(See page 7 Fig.A)
3The power plug must be correctly earthed, if in doubt, have it checked by a qualified Electrician. No other appliance should be connected to the same plug outlet by a double adapter or similar plug.
Dangerous voltage
5036 To indicate hazards arising from
5
INSTALLATION INSTRUCTIONS
Step 3 :
PREPARE DISHWASHER FOR INSTALLATION
1Lay the dishwasher on its back.
2Adjust the legs to the needed height of cabinet as shown in below figure.
Step 4 :
INSTALL THE DISHWASHER IN CUPBOARD
1Before sliding the dishwasher into the cupboard opening, all necessary final height adjustment and balancing adjustment should be done using the spanner.
2Slide the dishwasher into the cabinet opening carefully. Make sure that the drain hose inside the cabinet is not kinked or stretched.
CAUTION
If the height of cupboard is below 850mm, you should remove the top table by unscrewing the 2 screws. (Two of rear)
6
INSTALLATION INSTRUCTIONS
Step 5 :
DRAIN LINE CONNECTION
1If the end of drain hose does not fit to the drain line, use a piece of rubber connector(not supplied) that must be resistant to heat and detergent and may be obtained from a plumbing shop.
2There are 2 typical connections as shown in Figure A, B.
The “S” trap spigot must be drilled out cleanly and free of obstruction to its maximum internal diameter, if used for drainage.
To prevent siphoning, one of the following instruction methods must be followed:
■When the drain hose is connected to a sink “s” trap or waste disposal unit, the hose must be looped up to the underside of the bench top and secured.
Fig. A
■When the drain hose is connected to a separate stand pipe, it is essential that an air tight connection is made.
Refer to Fig.B
Fig. B : Drainage connection - stand pipe.
Drain Hose Extension
Extend Drain Hose as shown below.
CAUTION
When you connect or extend Drain Hose, make sure that drain hose is not kinked. (Bends should have 40 mm radius.)
7
INSTALLATION INSTRUCTIONS
Step 6 :
WATER SUPPLY CONNECTION
1Connect the water supply hose to the water tap as shown in figure.(Some models consist of an inlet valve and hose.) This dishwasher may be fed with either hot or cold water. If the water can not be maintained below 65ºC, the dishwasher must be connected to cold water.
2When connecting, the sealing tape or sealing compound should be used to avoid water leaks.
Make sure that the line is not kinked or sharply bent.
Water tap
Water supply hose
Step 7 :
FINAL CHECK AND ASSEMBLING
1Securely hand tighten supply hose to water supply.
Plug power supply cord into an earthed the power plug and switch on.
2After installing the product, operate the dishwasher through one cycle (Quick cycle is recommended) without loading the dishes.
Through this, you can check for water leak and operating conditions.
When you operate the product the first, the noise may be occurred.
In that case, turn off power switch and restart the dishwasher.
8
Step 8 :
HOW TO LEVEL THE PRODUCT
After installing the product, if you feel some sticky or hear a frictional sound between the side portion of door and tub when you open or close the door, you have to adjust the level of product.
Case 1. In case the door is slanted to the right
Slant to the right
DOOR
Fig. C
•If the door is slanted to the right as shown in figure C, repeat the procedure shown as below until the door is operated normally.
1)Unscrew(counter-clockwise) the left leg of back side and high the level.
2)Check the opening of door if there still remains sticky or friction sound.
•When the product is correctly leveled, there do not remain slant, stickiness or a friction sound.
Case 2. In case the door is slanted to the left
Slant to the right
DOOR
Fig. D
•If the door is slanted to the left as shown in figure D, repeat the procedure shown as below until the door is operated normally.
1)Unscrew(counter-clockwise) the right leg of back side and high the level.
2)Check the opening of door if there still remains sticky or friction sound.
•When the product is correctly leveled, there do not remain slant, stickiness or a friction sound.