Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
LCB5500-BN
LCB5500-BP
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK)
NO USER-SERVICEABLE PARTS INSIDE
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
This lightning flash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s enclosure
that may be of sufficient magnitude
to constitute a risk of electric shock to
persons.
The exclamation point within an
equilateral triangle is intended to
alert the user to the presence of
important operating and maintenance
(servicing) instructions in the literature
accompanying the product.
2
FCC WARNING: This equipment may generate or use
radio frequency energy. Changes or modifications to this
equipment may cause harmful interference unless the
modifications are expressly approved in the instruction
manual. The user could lose the authority to operate this
equipment if an unauthorized change or modification is
made.
REGULATORY INFORMATION: FCC Part 15
This equipment has been tested and found to comply
with the limits for a Class A digital device, pursuant to Part
15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference when
the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used in
accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to
cause harmful interference in which case the user will be
required to correct the interference at his own expense.
•A suitable conduit entries, knock-outs or glands shall
be provided in the cable entries of this product in the
end user.
•Caution: Danger of explosion if battery is incorrectly
replaced. Replaced only with the same or equivalent
type recommended by the manufacturer. Dispose
of used batteries according to the manufacturer’s
instructions.
•Holes in metal, through which insulated wires pass,
shall have smooth well rounded surfaces or shall be
provided with brushings.
This Class A digital apparatus complies with Canadian
ICES-003.
Cet appareil numérique de la classe A est conforme à la
norme NMB-003 du Canada.
Warning: Do not install this equipment in a confined space
such as a bookcase or similar unit.
Warning: Wiring methods shall be in accordance with the
National Electric Code, ANSI/NFPA 70.
Warning: This is a class A product. In a domestic
environment this product may cause radio interference
in which case the user may be required to take adequate
measures.
Warning: To reduce a risk of fire or electric shock, do not
expose this product to rain or moisture.
Warning: The product has been dropped or the case is
broken, turn off the power and unplug the power cord.
(This may cause fire, electric shock, or injury.)
Warning: If the product has no video out or sound, please
stop using. Unplug the power cable immediately and
contact the service center. (This may cause fire or electric
shock.)
Caution: This installation should be made by a qualified
service person and should conform to all local codes.
Caution: To avoid electrical shock, do not open the
cabinet. Refer servicing to qualified personnel only.
Caution: The apparatus shall not be exposed to water
(dripping or splashing) and no objects filled with liquids,
such as vases, shall be placed on the apparatus.
Caution: Prevent the power cable from being severely bent
or having pressure exerted on it by a heavy object.
To disconnect power from mains, pull out the mains
cord plug. When installing the product, ensure that the
plug is easily accessible.
3
Disposal of your old appliance
1. When this crossed-out wheeled bin
symbol is attached to a product it
means the product is covered by the
European Directive 2002/96/EC.
2. All electrical and electronic products
should be disposed of separately
from the municipal waste stream
via designated collection facilities
appointed by the government or the
local authorities.
3. The correct disposal of your old
appliance will help prevent potential
negative consequences for the
environment and human health.
4. For more detailed information about
disposal of your old appliance, please
contact your city office, waste disposal
service or the shop where you
purchased the product.
EEE Compliance with Directive. (for Turkey only)
4
LG Electronics hereby declares that this/
these product(s) is/are in compliance
with the essential requirements and other
relevant provisions of Directive 2004/108/
EC and 2011/65/EU.
European Standards Centre:
Krijgsman 1, 1186 DM Amstelveen The
Netherlands
Important Safety Instructions
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings. Install in
accordance with the manufacturer's instructions.
8. Do not install near any heat sources such as radiators,
heat registers, stoves, or other apparatus (including
amplifiers) that produce heat.
9. Do not defeat the safety purpose of the polarized or
grounding-type plug. A polarized plug has two blades
with one wider than the other. A grounding type plug
has two blades and a third grounding prong. The wide
blade or the third prong are provided for your safety. If
the provided plug does not fit into your outlet, consult
an electrician for replacement of the obsolete outlet.
10. Protect the power cord from being walked on or
pinched particularly at plugs, convenience receptacles,
and the point where they exit from the apparatus.
11. Only use attachments/accessories specified by the
manufacturer.
12. Use only with the cart, stand, tripod, bracket, or
table specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
13. Unplug this apparatus during lightning storms or
when unused for long periods of time.
14. Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
5
Cautions for Safe Operation
Power Supply
This camera must always be operated DC 12 V or AC 24 V.
Certified/Listed Adaptor which comply with LPS.
Handling of the unit
Be careful not to spill water or other liquids on the unit. Be
cautions not to get combustible or metallic material inside
the body. If used with foreign matter inside, the camera is
liable to fail or to get cause of fire or electric shock.
•Remove dust or dirt on the surface of the lens with a
blower.
•Use a dry soft cloth to clean the body. If it is very dirty,
use a cloth dampened with a small quantity of neutral
detergent then wipe dry.
•Avoid the use of volatile solvents such as thinners,
alcohol, benzene and insecticides. They may damage
the surface finish and/or impair the operation of the
camera.
6
Operating and storage location
Avoid viewing a very bright object (such as light fittings)
during an extended period. Avoid operating or storing the
unit in the following locations.
•Extremely hot or cold places (operating temperature
-10 °C to 50 °C, however, we recommend that the unit
be used within a temperature range of 0 °C to 45 °C)
•Damp or dust place
•Places exposed to rain
•Places subject to strong vibration
•Close to generators of powerful electromagnetic radia-
tion such as radio or TV transmitters.
Contents
Features ............................................................................. 8
Part Names and Functions ............................................... 9
This Color Video Camera is designed for installation in a video surveillance system.
This manual contains instructions on how to install and manage the Color Video Camera in your video surveillance system.
Should you require any technical assistance, please contact authorized service center.
•High resolution and high sensitivity with a 6 mm (1/3 Type) Super HAD CCD II.
•Automatically switch between DC 12 V and AC 24 V.
•Smart motion detector.
•Wide Dynamic Range (WDR)
8
Part Names and Functions
a b c d e
a Lens mount cap
The lens mount of the camera is covered using a cap
to protect it. Remove the lens cap covering the lens.
b Camera installation bracket
The bracket can be fixed at the top or bottom of the
camera.
c Flange-back adjustment lever
d Lens iris output connector (LENS)
This 4- pin connector is used to send the Iris control
signal and power supply to an auto-iris type lens.
e Setup menu control buttons
Use these buttons to set the menu options.
9
TRX -
TRX +
Part Names and Functions
f g h i
TRX -
TRX +
10
f Power input terminal
Supplies AC 24 V or DC 12 V from an external power
source.
g External Device Connectors
•D&N
Connect the external switch to set the D&N
function manually.
•ALARM (Alarm Output Terminal)
Connect to the alarm input of an external device.
•COM (COMMUNICATION)
Connect to an external controller of RS-485 format.
h Power indicator
Lights when the camera is powered.
i Video output connector (BNC type)
Supplies analog video signal (composite) to the
connected device such as a DVR or monitor.
Connections
Precautions
•Be sure to switch off the unit before installation and connection.
•A qualified service person, complying with all applicable codes, should perform all required hardware installation.
•Do not expose the power and connection cable to moisture, which may cause damage to the unit.
Connection Overview
RS-485 Unit
TRX -
External D&N
Switch
TRX +
11
Connections
Connecting Display device
The video signal connection between the camera and the
monitor.
TRX -
TRX +
12
Connecting Power Source
Connect power, using the method listed below:
1. Remove the insulation on the power cable as
illustrated. (a)
2. Attach the terminal tips. (b)
3. Connect the power source. (recommended power
adapter is AC 24 V/0.5 A, DC 12 V/0.5 A or above)
TRX -
TRX +
2mm
2mm
Connections
Connecting RS-485 Device
Use these ports to connect an external device of RS-485
format.
TRX -
TRX +
RS-485 Unit
TRX(-)
TRX(+)
RS-485 Protocol
Data Communication Format
•Data Length: 1 Byte (8 Bit)
•Start/Stop Bit: 1 Bit
•Parity Bit: None
•Baud rate: 9 600 bps
Format
BYTE1 BYTE2 BYTE3
0xE5 0x86 Camera ID
BYTE4 BYTE5 BYTE6
CODE1 CODE2 *C.S.
*C.S. = Check Sum
•The data of total 6 bytes is transmitted from the
external RS-485 device to the camera.
•BYTE 6 : The value of Check Sum from ‘BYTE 1 ’ to
‘BYTE 5 ’.
ex) In case of transmission, 0xC5, 0x5F, 0x02, 0x00,
0x0A”
C.S. = 0xC5 +0x5F +0x02 +0x00 +0x0A = 0x0130
therefore, C.S. = 0x30
Commands
Function Command
OSD Menu ON/OFF E5, 86, ID, 41, 02, C.S.
13
Loading...
+ 28 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.