
Bluetooth Module
Bluetooth Module Manual
Warranty period: 2 years
A/S: 1544-7777

1. INTRODUCTION
1.1 Overview
LCB-001 is a small size and low power module for Bluetooth with PCB antenna. LCB-001 use the
nRF52810 solution(Nordic), and it can be applied to air solution, home appliances etc.
Nordic nRF52810 is a highly integrated single-chip low power Bluetooth network controller. It
combines an ARM-Cortex M4 MCU, Bluetooth, and RF in a single chip. It also provides a bunch of
configurable GPIOs which are configured as digital peripherals for different applications and control
usage.
nRF52810 integrates internal memories for complete Bluetooth functions. The embedded memory
configuration also provides simple application developments.
1.2 Key Features
Bluetooth LE
Supported data rates: 1 Mbps Bluetooth® low energy mode
Integrated PCB antenna
SIZE : 48mm x 20mm x 10mm
-90 dBm sensitivity in Bluetooth® low energy mode (2.4GHz)
-20 to +4 dBm TX power, configurable in 4 dB steps
On-chip balun (single-ended RF)
20 mA peak current in TX (4 dBm)
15 mA peak current in RX

3. ELECTRICAL SPECIFICATION
3.1 Absolute Maximum Ratings
3.2 Operating conditions
3.3 Power Supply Voltages
3.4 Current Consumption

3.5 Standard Rated Specification
Division Characteristic
Host Interface UART
Frequency Range 2.402GHz ~ 2.480GHz (2.4GHZ ISM)
Dimension L x W x H : 48 x 20 x 10 (typical) mm
Spread Spectrum FHSS (Frequency Hopping Spread Spectrum)
Data Rate 1 Mbps
3.6 Electrical Specifications for Bluetooth (Radiation TEST)
TX characteristics
RX characteristics
Sensitivity
Low Energy/ 1Mbps

5. FCC CERTIFICATION
5.1 FCC Notice
This equipment has been tested and found to comply with the limits for a Class B digital
device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide
reasonable protection against harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio frequency energy and, if not installed and
used in accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and the receiver.
- Connect the equipment to an outlet on a circuit different from that to which the receiver
is connected.
- Consult the dealer or an experienced radio/TV technician for help.
This device complies with part 15 of the FCC Rules. Operation is subject to the following
two conditions:
(1) This device may not cause harmful interference and
(2) This device must accept any interference received, including interference that may cause
undesired operation of the device.
Any changes or modifications in construction of this device which are not expressly
approved by the party responsible for compliance could void the user’s authority to
operate the equipment.
Please notice that if the FCC identification number is not visible when the module is installed
inside another device,
then the outside of the device into which the module is installed must also display a label
referring to the enclosed module.
This exterior label can use wording such as the following: “Contains FCC ID : BEJ-LCB001” any
similar wording that expresses the same meaning may be used.
5.2 FCC RF Radiation Exposure Statement
This equipment complies with FCC radiation exposure limits set forth for an uncontrolled
environment. This transmitter must not be co-located or operating in conjunction with any
other antenna or transmitter.
This equipment should be installed and operated with a minimum distance of 20
inches) between the antenna and your body. Users must follow the specific operating
instructions for satisfying RF exposure compliance.
cm (7.8

6. IC CERTIFICATION
6.1 Industry Canada Statement
This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation,
Science and Economic Development Canada’s licence-exempt RSS(s). Operation is subject
to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may cause
undesired operation of the device.
Le présent appareil est conforme aux CNR d'Industrie Canada applicables aux appareils radio
exempts de licence.
L'exploitation est autorisée aux deux conditions suivantes : (1) L'appareil ne doit pas produire
de brouillage, et (2) L'utilisateur de l'appareil doit accepter tout brouillage radioélectrique
subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.
Please notice that if the IC identification number is not visible when the module is installed
inside another device, then the outside of the device into which the module is installed must
also display a label referring to the enclosed module. This exterior label can use wording such
as the following: “Contains IC : 2703N-LCB001” any similar wording that expresses
the same meaning may be used.
L’étiquette d’homologation d’un module d’Innovation, Sciences et Développement
économique Canada devra être posée sur le produit hôte à un endroit bien en vue, en tout
temps. En l’absence d’étiquette, le produit hôte doit porter une étiquette sur laquelle figure le
numéro d’homologation du module d’Innovation, Sciences et Développement économique
Canada, précédé du mot « contient », ou d’une formulation similaire allant dans le même sens
et qui va comme suit : Contient IC : 2703N-LCB001 est le numéro d’homologation du module

6.2 IC Radiation Exposure Statement
This equipment complies with IC radiation exposure limits set forth for an uncontrolled
environment. This equipment should be installed and operated with a minimum distance of
20 cm (7.8 inches) between the antenna and your body.
NOTE: THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTERFERENCE
CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS EQUIPMENT. SUCH
MODIFICATIONS COULD VOID THE USER’S AUTHORITY TO OPERATE THE EQUIPMENT.
Cet équipement est conforme aux limites d'exposition aux rayonnements IC définies pour un
environnement non contrôlé. Cet équipement doit être installé et utilisé avec une distance
minimale de 20 cm (7,8 pouces) entre l’antenne et votre corps.
REMARQUE: LE FABRICANT NE PEUT ÊTRE TENU RESPONSABLE DES INTERFÉRENCES RADIO
OU TÉLÉVISÉES CAUSÉES PAR DES MODIFICATIONS NON AUTORISÉES DE CET APPAREIL. CES
MODIFICATIONS PEUVENT ANNULER L’AUTORITE DE L’UTILISATEUR A FAIRE FONCTIONNER
L’APPAREIL.
Bluetooth module specifications
Model LCB-001
Frequency Range 2402 MHz - 2480 MHz
Output Power (Max)
5.26 dBm