LG LC703N-B Owner’s Manual

Color Video Camera

Instruction Manual

Models : LC703

LC702

LC701

Before installing, operating or adjusting this product, please read this instruction booklet carefully and completely.

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated

dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy. Changes or modifications to this equipment may cause harmful interference unless the modifications are expressly approved in the

instruction manual. The user could lose the authority to operate this equipment if an unauthorized change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment.

This equipment generates, uses, and can radiate radio frequency energy and, if not installed and

used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.

•A suitable conduit entries, knock-outs or glands shall be provided in the cable entries of this product in the end user.

•Caution: Danger of explosion if battery is incorrectly replaced. Replaced only with the same or equivalent type recommended by the manufacturer. Dispose of used batteries according to the manufacturer’s instructions.

•Holes in metal, through which insulated wires pass, shall have smooth well rounded surfaces or shall be provided with brushings.

Warning: Do not install this equipment in a confined space such as a bookcase or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product may cause radio interference in which case the user may be required to take adequate measures.

Warning: To reduce a risk of fire or electric shock, do not expose this product to rain or moisture.

Caution: This installation should be made by a qualified service person and should conform to all local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to qualified personnel only. Caution: The apparatus shall not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, shall be placed on the apparatus.

To disconnect power from the mains, pull out the mains cord plug. When install the product, ensure that the plug is easily accessible.

Disposal of your old appliance

1.When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/ EC.

2.All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3.The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4.For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

This product is manufactured to comply with EMC Directive 2004/108/EC and Low Voltage Directive 2006/95/EC.

European representative :

LG Electronics Service Europe B.V. Veluwezoom 15, 1327 AE Almere,

The Netherlands (Tel : +31-036-547-8940)

Important Safety Instructions

1.Read these instructions.

2.Keep these instructions.

3.Heed all warnings.

4.Follow all instructions.

5.Do not use this apparatus near water.

6.Clean only with dry cloth.

7.Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

8.Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat.

9.Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. A grounding type plug has two blades and a third grounding prong. The wide blade or the third prong are provided for your safety. If the provided plug does not fit into your outlet, consult an electrician for replacement of the obsolete outlet.

10.Protect the power cord from being walked on or pinched particularly at plugs, convenience receptacles, and the point where they exit from the apparatus.

11.Only use attachments/accessories specified by the manufacturer.

12.Use only with the cart, stand, tripod, bracket, or table specified by the manufacturer, or sold with the apparatus. When a cart is used, use caution when moving the cart/apparatus combination to avoid injury from tip-over.

13.Unplug this apparatus during lightning storms or when unused for long periods of time.

14.Refer all servicing to qualified service personnel. Servicing is required when the apparatus has been damaged in any way, such as powersupply cord or plug is damaged, liquid has been spilled or objects have fallen into the apparatus, the apparatus has been exposed to rain or moisture, does not operate normally, or has been dropped.

Contents

Features . . . . . . . . . . .	.	.	.	.6	Privacy Mask setting . . . . . .	. . . .30
Cautions for Safe Operation . . . .	.	.	.	7	3D-DNR setting . . . . . . . . . . . .32
Part Names and Functions . . . .	.	.	.	.8	Special menu settings . . . . .	. . . . 33
Connections . . . . . . . . . . . . . . . . . . . .	. .	. .	. .11		Reset settings . . . . . . . . . . . . 39
Installation of Camera . . . . . .	.	.	.	15	On Screen Display . . . . . .	. . . . 40
Menu Operation . . . . . . . . .	.	.	.16		RS-485 Protocol . . . . . . . . . . . 43
Focus settings . . . . . . . . .	. . .			19	Specification . . . . . . . . .	. . . .45
Exposure settings . . . . . . . . . . .22
White Balance setting . . . . . .	.	.	.	26
Day/Night setting . . . . . . . .	.	.	.	28
Motion Detection setting . . . . .	.	.	.	29

Features

This color video camera is designed for use in monitoring system.

•High resolution and high sensitivity with a 1/ 4 inch EX-View CCD (Charge Coupled Device).

•High magnitude of zoom lens with optical x27, Digital x12 (MAX x324)

•Auto Focus

•Auto White Balance

•Auto exposure with DC Iris control

•Day & Night function

•WDR(Wide Dynamic Range) is available

Features Chart

This table shows the differences between the models.

Use LC703 is used for the description, operations and details provided in this operating guide.

Models	Resolution	Sens-Up	WDR	Day & Night	Communication	HSBLC
LC703P	High	Yes	Yes	Yes	RS-485	Yes
LC703N	High	Yes	Yes	Yes	RS-485	Yes
LC702P	High	No	Yes	Yes	RS-485	No
LC702N	High	No	Yes	Yes	RS-485	No
LC701P	High	Yes	No	Yes	RS-485	Yes
LC701N	High	Yes	No	Yes	RS-485	Yes

Cautions for Safe Operation

Power Supply

This camera must be operated DC 12V Certified/Listed, class 2 power supply only.

Handling of the unit

Be careful not to spill water or other liquids on the unit. Be cautions not to get combustible or metallic material inside the body. If used with foreign matter inside, the camera is liable to fail or to get cause of fire or electric shock.

•Remove dust or dirt on the surface of the lens with a blower.

•Use a dry soft cloth to clean the body. If it is very dirty,use a cloth dampened with a small quantity of neutral detergent,then wipe dry.

•Avoid the use of volatile solvents such as thinners,al cohol,benzene,and insecticides.

They may damage the surface finish and/or impair the operation of the camera.

Operating and storage location

Avoid viewing a very bright object (such as light fittings) during an extended period. Avoid operating or storing the unit in the following locations.

•Extremely hot or cold places (operating temperature -10 °C - 50 °C, however, we recommend that the unit be used within a temperature range of 0 °C - 45 °C)

•Damp or dust place

•Places exposed to rain

•Places subject to strong vibration

•Close to generators of powerful electromagnetic radiation such as radio or TV transmitters.

Part Names and Functions

aa Lens mount cap

The cap is installed to protect the lens mount section. Remove the lens mount cap before install the camera. (sold separately) .

b Camera installation bracket

The bracket can be fixed at the top or bottom of the camera.

Part Names and Functions

c d e

cPower indicator

Comes on when the power to the camera is on.

dControl buttons

•T(TELE) button

When push, picture is telephoto.

•N(NEAR) button

In a manual situation, focus get near.

•M(MENU) button.

If you want to set up a diverse function, you can push this button.

•W(WIDE) button

When push, picture is wide angle.

•F(FAR) button

In a manual situation, focus get far.

•H(HOT) button

When you set the DAY/NIGHT mode to EXT, you can change the Day/Night mode using this button.

eVideo output connector (BNC type)

Connect this connector to a device such as a VCR or monitor with a VIDEO IN connector.

Part Names and Functions

fPower input terminal

Connect to an external power supply of DC 12V.

gExternal Device Connectors

•TRX -/+

Connect to an external controller of RS-485 format.

•GND

Common GND.

•Alarm Output Terminal (ALARM) Connect to the alarm input of an external device.

•COM (Common)

•OSD/D&N

-OSD: Connect the external controller to control the OSD function manually.

-D&N: Connect the external controller to set the D&N function manually. If you use the external D&N function, you should set the DAY/NIGHT option to EXT on the camera setup menu.

•FOCUS/ZOOM

Connect the external controller to control the Focus and Zoom function manually.

Connections

Power connection

1.Remove the insulation on the power cable as illustrated.

2.Attach the terminal tips.

3.Connect to the 12V DC UL Listed, Class 2 Power Supply only on the camera.

Connecting Monitor

The video signal connection between the camera and the monitor or DVR.

Connections

Connecting RS-485 Controller

Connect to an external controller of RS-485 format.

TRX -

RS-485

Controller TRX +

5~7 mm

Alarm Connection

Connect an external device such as a buzzer or lamp to the ALARM terminal. When the camera detects motion, the alarm output signal is supplied to the connected external device.

Contact Ratings

•Maximum load current is ±130mA.

•Do not connect any system or device that has over 40 Vp-p (DC 30 V) bias voltage on the contact terminal.

Note:

Use a relay unit if the voltage or current of the connected device exceeds the ratings.

Connections

Day&Night function settings

If you set the DAY/NIGHT option to EXT on the [CAMERA SET] menu, you can set the D&N function manually.

In case that current D&N mode is set to Day mode

When you input the "+5V" signal to the OSD/D&N terminal and the COM is connected to grounds, the D&N mode is set to Night mode.

In case that current D&N mode is set to Night mode

When you input the "+5V" signal to the OSD/D&N terminal and the COM is connected to ground, the D&N mode is set to the Day mode.

COMMON D&N (+5V ~ +12V)

OSD function settings

When you connect the "-5V" signal to the OSD/D&N terminal, the menu is displayed or the sub menu is displayed or the selected menu option is activated according to current conditions.

COMMON

OSD (-5V ~ -12V)

Connections

FOCUS and ZOOM Function Settings	ZOOM function
You can set the FOCUS and ZOOM function manually.
Using the external controller or receiver unit to control
the FOCUS and ZOOM functions.
FOCUS function	COMMON
	ZOOM (+: Tele, -: Wide)
COMMON
FOCUS (+: Near, -: Far)

Installation of Camera

The bracket can be installed to either the top of the camera as desired. When changing the position of the camera mounting bracket, you should always reuse the screws that have been removed.

Note:

If using a camera mounting bracket, select a location that is strong enough to bear the full weight of the camera and the mounting bracket for long periods, and install the camera and mounting bracket securely.

+ 33 hidden pages