Page 1
7 inch Wide TFT color
TV System/Mobile Monitor
OWNER’S MANUAL
LAM770T1/LAM770
Before connecting, operating or adjusting this
product, please read this instruction booklet
carefully and completely.
LM770T1/LAM770_ENG_LGEPL_MFL41488902
Page 2
Table of contents
2
Important Safety Instruction 3-6
Installation 9-14
Parts supplied . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Before installing . . . . . . . . . . . . . . . . . . . . . . . . . . . . .9
Installation order for the stand . . . . . . . . . . . . . . . . . .10
Treatment of monitor cable . . . . . . . . . . . . . . . . . . . .11
Installation of monitor unit . . . . . . . . . . . . . . . . . . .11-12
Installation order for the stand (Rear seat monitor) . . .13
Connection of exterior units . . . . . . . . . . . . . . . . . . . .14
Parts name 15-17
Front view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15
Rear view . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .16
Remote control . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Battery installation . . . . . . . . . . . . . . . . . . . . . . . . . . .17
Operation 18-21
Power ON/OFF . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Mode conversion . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
Adjusting the volume . . . . . . . . . . . . . . . . . . . . . . . . .18
Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .18
To enter the FUNCTION menu . . . . . . . . . . . . . . . . .19
Adjusting FUNCTION menu . . . . . . . . . . . . . . . . . . . .19
To enter the TV SETUP menu . . . . . . . . . . . . . . . . . .20
Adjusting TV SETUP menu . . . . . . . . . . . . . . . . . .20-21
Main features 7-8
Troubleshooting 22-23
Specifications 24
Page 3
3
Important Safety Instruction
TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT SPLIT
COVER(OR BACK) NO USER SERVICEABLE PARTS INSIDE.
REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
The lightning flash with arrowhead symbol, within an equilateral
triangle is intended to alert the user about the presence of
uninsulated dangerous voltage within the product’s enclosure that
may be of sufficient magnitude to constitute a risk of electric shock.
The exclamation point within an equilateral triangle is intended to
alert the user to the presence of important operating and
maintenance (servicing) instructions in the literature accompanying
the appliance.
To prevent a user or others from any physical or financial damage,
please abide by the following. The following indications describe the
degree of danger or damage for the misusage.
To reduce the risk of fire or electric shock, do not expose this
apparatus to rain or moisture.
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings
4. Follow all warnings.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
Page 4
Important Safety Instruction
4
1. Do not operate the TV while driving.
Operating while driving may cause a fatal or serious accident.
Always operate after the vehicle is parked at a safe place.
2. While driving, do not watch the TV or video
Watching TV or video while driving may cause a serious accident.
3. At a trouble or abnormal state, do not use it.
If you use it at no sound or with smoke or strange smell, this can be the
cause of a fire.
4. Do not expose your eyes or face close to the pole of an antenna.
This may be the cause of injury.
5. In case of vehicles equipped with air bags, place the TV away from the
operation range of the air bags.
In case of an accident, impact between the air bags and the TV may cause
a serious facial injury to passengers.
6. To place the TV with a double - sided tape, ensure to wash the
adhesive side cleanly then place it.
7. Excessive sound pressure from earphones and headphones can cause
hearing loss.
1. Do not disassemble or modify it.
This may be the cause of an accident like a breakdown or a fire.
Note
TV function is only available for LAM770T1.
Disassembling prohibited
Warning
Prohibition
Warning
Page 5
5
Important Safety Instruction
1. Do not drop it and avoid heavy impact at anytime.
This may be the cause of a trouble or a fire.
2. Do not watch TV for a long time with engine turned off.
A vehicle may not start due to the discharge of battery.
3. Do not grab the lower part of the antenna to adjust an angle.
4. Do not charge, disassemble or heat the battery and keep it away from
fire.
This may be the cause of an explosion or a leakage.
5. Keep a glass washer out of children's reach.
If it goes into eyes, wash them cleanly with water and consult with a doctor.
6. Do not install near any heat sources such as radiators, heat registers,
or other apparatus (including amplifiers) that produce heat.
7. Don't block any ventilation openings, install in accordance with the
manufacturer's instructions.
8. To prevent injury, this apparatus must be securely attached or fixed in
accordance with the installation instructions
Note
TV function is only available for LAM770T1.
Prohibition
Notice
Page 6
Important Safety Instruction
6
1 Do not touch an antenna line or the TV when lightning.
This may be the cause of an electric shock.
2. In case that cable passes through a hole or touches a metal part,
protect it appropriately.
3. Keep the battery out of children's reach.
If a child swallows it, consult with a doctor right away.
4. Do ask a experienced technician to install this product.
Skilled technique and experience are required to install and wire.
For your safety, ask a sales agency to do those kinds of works.
5. Protect the power cord so that it does not get walked on or pinched,
particularly at the plug, convenience receptacles and the connecting
point from the device.
6. Only use attachments/accessories designated by the manufacturer.
7. Use the product only with the cart, stand, tripod, bracket or table
designated by the manufacturer or sold with the device. When the cart
is used, be careful not to get injured from the cart with the device
tipping over.
8. Unplug the device during thunder storms or when not used for a long
period of time.
9. All services must be done by a qualified service personnel. Service is
required when the apparatus has been damaged in any way, such as
damaged power-supply cord or plug, liquid spilled on product or
objects fallen on the device, exposure to rain or moisture, abnormal
operation or when the product has been dropped.
Compulsion
Notice
Page 7
7
Main features
This unit is designed to fit the environment of vehicles. Unlike general units for
home Use, the unit for the Vehicles is equipped with a special circuit inside the
product to provide good quality picture and sound.
1. Video Low reflection and high definition LCD
Our LCD provides HD quality screen using 7 inch wide TFT LCD.
In addition, it has the pixel disposition structure suitable to watch screen
during Navigation.
Forced Synchronization Circuit
This circuit minimizes the shaking of the screen in order to provide a stable
screen during motion.
2. Audio Sound conversion function
A built-in speaker with max of 1W output is equipped inside.
Noise Canceller Circuit
The Noise Canceller Circuit is designed to cancel the noises that can arise
from the vehicle.
Ear-Phone Function
Can hear voice by Earphone in vehicles.
3. Exterior Audio/Video Input Function
Our unit has an outlet to connect with audio/video.
Disposal of your old appliance
1. When this crossed-out wheeled bin symbol is attached to a product,
it means the product is covered by the European Directive 2002/96/EC.
2. All electrical and electronic products should be disposed of separately from
the municipal waste stream via designated collection facilities appointed by
the government or the local authorities.
3. The correct disposal of your old appliance will help prevent potential
negative consequences for the environment and human health.
4. For more detailed information about disposal of your old appliance, please
contact your city office, waste disposal service or the shop where you
purchased the product.
Page 8
Main features
8
4. Convenient Functions
Dimmer Function
According to the brightness of surrounding, that of the screen can be
adjusted.
Up to 99 channel memory
Our TV is capable of transmitting regular broadcasting TV (public) and
automatically memorizes up to 99 channels for regular broadcasting TV
stations.
Remote Controller
A user-friendly remote controller is provided.
Auto Search Function
Auto search function is designed to find next available TV station and to
memorize the station automatically. Just simply push the search button and
you can easily find the TV station you want.
Full-Down Menu
All the function are displayed in one screen for your convenience.
AV1/AV2 Select Function
Can select AV1/AV2
Note
The LAM770T1 has three signal sources ; AV1, AV2 and TV, but the
LAM770 only has two signal sources; AV1 and AV2.
LAM770T1 has TV mode when press the mode convention button.
The TV function will be had, but the LAM770 does not have TV mode.
LAM770T1, when in TV mode , the menu button is pressed the TV tuning
menu will be had the CHANNEL, BADD/ERASE, BSOUND SYSTERM, BFINE
TUNE, BAUTO MEMORY and ALL RESET FUNCTIONS can be used,but the
LAM770 doesn’t have the function.
The remote controller is different.the LAM770T1 has 0-9 number buttons, but
the LAM770 doesn’t have.
The LAM770T1 has TV antenna but the LAM770 doesn’t have."
Page 9
9
Installation
At low temperature (20°C… or less)
Turn on the heater for a proper temperature.
(to enhance adhesive power).
At high humidity (fog, rain and so on)
After making adhesive side dried with a dryer,
install the TV.
After installing of the Stand
Pulling the Monitor stand or installing the Monitor
within 24 hours of the stand installation may
weaken adhesive power of the stand.
Before installing
Parts supplied
AV Cable
Cigar light adapter Remote Control
Section-mount cradle
(Rear)
Section-mount cradle
(Front)
Cover case
Page 10
Installation
10
Installation order for the Stand
1. Decide a place for installation and make a
forming by bending the adhesive side of the
Stand according to the shape of the place.
2. Wash the adhesive side cleanly with a neutral
detergent or alcohol.
3. After uncovering a double-sided tape out of the
Stand, install it.
If the temperature of the adhesive side is low
(20°C… or less), the adhesive power of the tape
may be weaken. To prevent this, stick the Stand
after heated.
4. Drive the screws into the product.
(The screws is not supplied.)
After screwing, check and take notice to escape
any damage to the wire or the equipment of
dashboard inside.
5. While putting the stand screw into a hole placed
on the back side of the monitor unit, adjust
installation height and angle.
Adjust the height and angle of the unit to reach a
dashboard in order to prevent trembling by the
vibration of a vehicle. After adjusting the height
and angle, surely screw to fix it. While driving, this
may be the cause of an accident by its bolting.
Notice
Notice
Notice
Double-sided tape
Page 11
11
Installation
Treatment of monitor cable
• If the Monitor is installed and the Cable
connected, put the cable in a good order not to
disturb a safe driving.
• Pay attention to the cable not being caught in the
rail of a door or a seat. The cable may be cut by
its getting caught in.
• Because it is very dangerous for the cable to be
rolled up by a shift lever, arrange it well with a
cable clamp.
Installation of monitor unit
• The Monitor unit of this product is designed
taking a serious views for safety.
• Unless you surely install it on a safe place, this
may be the cause of an accident and be very
dangerous.
• When you decide a place for attachment, check
following notices necessarily.
Importance
Importance
Page 12
Installation
12
Adhere it on a place not to disturb the operation of
air bags.
• Do not install on the place where disturbs front
sight and the operating of steering, transmission
shift lever, brake pedal and makes other
passengers risky. This may be the cause of an
accident or an injury.
• As shown on the above, attach it on a safe place
where it does not disturb front sight or you don't
have to avert your eyes extremely.
• Do not install it on a place where it is exposed at
extremely high or low temperature. This may
make the monitor unit transformed or be the
cause of a trouble.
• While parking, protect it against the direct rays of
the sun with the enclosed monitor cover
because high temperature may influence on it.
• Do not attach on a place where the wind of air
conditioner can directly reach the monitor unit.
• Do not attach on a place where it disturbs the
opening of Globe Box.
• Do not install it on a wooden panel or a textile
one because it is likely to be damaged.
Importance
Notice
Importance
Page 13
13
Installation
Installation order for the stand
(Rear seat monitor)
1. First, separate the head rest A.
Note
Refer to your car’s user guide.
2. Insert the head rest A into the a hole placed on
the up side of the section-mount cradle.
3. Install the head rest A into the a hole placed on
the up side of the seat.
4. Drive the enclosed screws into the unit.
5. While putting the Stand screw into a hole
placed on the bottom side of the unit, adjust
installation height and angle.
Adjust the angle of the unit to reach a seat in order
to prevent trembling by the vibration of a vehicle.
After adjusting the angle, surely screw to fix it.
While driving, this may be the cause of an accident
by its bolting.
Notice
A
Page 14
Installation
14
Connection of exterior units
Connect it with a Cigar Jack.
Can use to DC 12 V by Free
Voltage employment.
DVD, Video Camera,
LDP, Player and etc.
Note
TV function is only available for LAM770T1.
When the AV Cable is insert and pulled out of the AV jack, the picture will
flicker for a short moment, which is normal.
OR
Page 15
15
Parts name
1. : Power ON/OFF
2. • TV/AV : Mode conversion (TV t AV1 IN t AV2 IN) : LAM770T1
• AV1/AV2 : Mode conversion (AV1 IN t AV2 IN) : LAM770
3.
VV
:• Channel down select : LAM770T1
• Down button / Menu item select
4.vv:• Channel up select : LAM770T1
• Up button / Menu item select
5. STBY (R) : Standby lamp (Red color)
PWR (G ) : Power Lamp (Green color)
6.BB: Volume up / Menu item adjust
7.bb: Volume down / Menu item adjust
8. MENU : Enter menu
9. : Earphone socket
1 2 3 4 5 6 7 8 9
Front view
Note
Please use the appropriate jack connector for the antenna input.
Page 16
Parts name
16
1. Left/ Right Speakers
2. TV Antenna (TV function is only available for LAM770T1.)
3. Docking connector
1
2
3
1
Rear view
Note
Actual player may vary slightly from images shown.
Page 17
17
Parts name
1. Remove the battery holder with fingers.
2. Install the battery on the battery holder.
3. Install the battery holder back into its original
position.
Notes
• Use only one CR2025 (3V) lithium battery.
• Remove the battery if the remote control is
not used for a long period of time.
• Do not leave the product in a hot or humid
place.
• Do not handle the battery with metallic tools.
• Do not store the battery with metallic
materials.
• In the event of battery leakage, wipe the
remote control completely clean and install a
new battery.
Battery installation
1. POWER
2. • TV/AV : Mode conversion
(TV t AV1 IN t AV2 IN) : LAM770T1
• AV1/AV2 : Mode conversion
(AV1 IN t AV2 IN) : LAM770
3. NUMBER [0 -9]
4. MENU
5. • CHANNEL UPUU/ DOWN uu: LAM770T1
• Menu item select
6. • VOLUME UP / DOWN
• Menu item adjust
7. MUTE (AUDIO MUTE)
1
Remote control
2
3
4
6
7
5
Battery holder
Page 18
Operation
18
Power ON/OFF
• When connecting the power to the main system,
red LED of STBY lights on.
• Press the Power button, the ON/OFF can be
repeatedly executed.
• At the power ON, green LED of PWR lights on.
Note
When power of the main system is turned on or
off, the picture sometimes flicker, which is normal.
Mode conversion
• Press the TV/AV button repeatedly.
Mode is changed.
TV (LAM770T1) t AV1 IN t AV2 IN...
•In " TV " display mode, a channel number
displays. Besides, AV1/AV2 displays.
Notes
If power is supplied to the main system, the TV
memorizes the previous status and makes
ON/OFF automatically.
Adjusting the volume
Press the
bb
or
BB
buttons to adjust the sound level.
The minimum volume is 0 and the maximum volume is 30.
Note
When you turn the unit off, the current volume
level is automatically memorized.
Mute
Press the MUTE on the remote control to cut the
sound. To cancel it, press again.
STBY : RED
PWR : GREEN
Page 19
19
Operation
To enter the FUNCTION menu
1. Select the TV, AV1, or AV2 by pressing the
TV/AV button repeatedly.
2. Press the MENU button.
The “TV SETUP” menu is displayed.
Note
When you press the AV1/AV2 switch, the
picture will flicker for seconds, which is normal.
Adjusting FUNCTION menu
1. Press the vvorVVbuttons to select a item.
2. Press the bborBBbuttons to adjust.
Note
When the MODE is changed between 16:9
and 4:3, the picture will flicker for a second,
which is normal.
Item
COLOR
BRIGHT
CONTRAST
MODE
ROTATE
LANGUAGE
VOL
bb
Paler
Weaker
Darker
16 : 9 n 4 : 3
Rotating the menu screen.
ENGLISH n RUSSIAN
VOL
BB
Deeper
Stronger
Lighter
16 : 9 n 4 : 3
Rotating the menu screen.
ENGLISH n RUSSIAN
COLOR 30
BRIGHT
CONTRAST
MODE
ROTATE
LANGUAGE
FUNCTION
30
33
16 : 9
ENGLISH
Page 20
Operation
20
To enter the TV SETUP menu
1. Select the TV by pressing the TV/AV button
repeatedly.
2. Press the MENU button twice.
The “TV SETUP” menu is displayed.
Adjusting TV SETUP menu
1. Press the vvorVVbuttons to select a item.
2. Press the bborBBbuttons to adjust.
Note
TV function is only available for LAM770T1.
SYSTEM
If the sound is abnormal, maybe the sound
system setting is wrong. You can select a
proper sound system as follow.
PAL B/G y SECAM D/K y PAL D/K
Press the
bb
or BBbuttons to select a proper
sound system.
CHANNEL
Press the
bb
or BBbuttons to start auto search.
All active channels will be preset and stored
into the memory automatically. After presetting,
the TV will go to the channel before the auto
search starts.
TV SETUP
SYSTEM PAL B/G
CHANNEL
FINE
BAND
SKIP
MANUAL
AUTO
438.00MHZ
UHF
OFF
9
Page 21
21
Operation
FINE
Fine tuning is unnecessary under normal
conditions. However in areas of inferior
broadcast conditions where adjustment is
necessary for a better picture and sound, use
FINE TUNE.
1. Press the vvorVVbuttons to select the
CHANNEL item.
2. Press the bborBBbuttons to select a
channel number you want to fine tune.
(For example, channel 10)
3. Press the vvorVVbuttons to select the
“FINE” item.
4. Press the
bb
or BBbuttons to fine tune till the
best possible picture and sound are
obtained.
BAND
Press the
bb
or BBbuttons to select the
the desired frequency.
UHF y VHF L y VHF H
SKIP
Press the
bb
or BBbuttons to skip a channel.
MANUAL
Press the
bb
or BBbuttons to start manual
search.
AUTO
Press the
bb
or BBbuttons to start auto search.
All active channels will be preset and stored
into the memory automatically. After presetting,
the TV will go to the channel before the auto
search starts.
Page 22
Troubleshooting
22
Check following points first before judging as trouble.
Although you have checked following points, if a problem still remains, call the
service center in this manual and we will take a proper action. (As this product is
assembled in delicate parts, only a skilled technician is recommended for the
disassembly of product.)
Small red, blue and green points display on the screen.
•
LCD screen is made in a high technology. So, this may happen due to lack of
pixels by 0.001% or frequent lighting up of pixels. But, it is not the reason of
any trouble.
Audio and Video do not work.
• Check if the starting switch of a car is on ACC or ON.
• Check whether a connection code is unstable or is disconnected.
• This does not work while driving.
Video works but Audio does not.
• Check with a volume controller if the volume level is proper.
• Check whether an output port for voice is connected.
The corner of the screen displays on TV.
• If LCD screen has been used for long dark hours, it becomes dark gradually.
• If it gets dark severely, replace its exclusive fluorescent tube.
Voice quality is bad while receiving TV signal.
• Change the frequency in case of interference from a radio station.
TV displays only in black.
• Check its color by adjusting Color Set on Menu.
Note
TV function is only available for LAM770T1.
Page 23
23
Troubleshooting
These cases are not the trouble.
Under following cases, it is difficult to watch TV because TV receiving signal is
bad.
Faded in
double or triple
Between Buildings
At an airplane or a
train passing
nearby
In the neighborhood of a radio broadcasting or the
transmission antenna of an amateur radio station.
Shaking
A neon sign nearby
A automobile
A motorcycle
A high tension wire
Far away from a
radio station
In the mountain or
forest
Screen is
spotted.
Field gets bad
gradually.
Color appears or
disappears.
A power cable
nearby
It noises. It noises.
Stripes appear.
Deep in the mountains
Screen
Sound
Environment
Screen
It noises. It noises.
Sound
Environment
Page 24
Specifications
24
Type.....................................................................................LCD color monitor
Power supply ......................................................................................DC 12 V
Consumption power .................................................................................12 W
Receiving channel.........................................................................99 channels
Operating temperature.................................................................-10°C - 60°C
Maintenance temperature............................................................-20°C - 80°C
LCD panel.............................................................7 inch wide TFT LCD panel
Pixels ................................................................................................234 x 480
Effective pixels........................................................................99.99% or more
Display............................................................Transmission type of color filter
Operating system .................................................................TFT active matrix
Sight angle (Left/Right) ..................................................................120° (±60°)
Sight angle (Up/Down) .........................................................................20°-40°
LCD lighting....................................................................................L type CCFL
Voice power...................................................................................1.5 Watt x 2
Size .................................................................W x Lx H : 191.5 x 120 x 27 mm
Weight .....................................................................................................400 g
Page 25
P/NO : MFL41488902
Loading...