LG L332-CP User Manual

OWNER'S MANUAL

Color Video Camera

Please read this manual carefully before operating
your set and retain it for future reference.

P/NO : MFL63745135(A)

MODEL

L332-BN/L332-BP
L332-CP

Important Safety Instructions

1. Read these instructions.

2. Keep these instructions.

3. Heed all warnings.

4. Follow all instructions.

5. Do not use this apparatus near water.

6. Clean only with dry cloth.

7. Do not block any ventilation openings. Install in accordance with the
manufacturer’s instructions.

8. Do not install near any heat sources such as radiators, heat registers,
stoves, or other apparatus (including amplifiers) that produce heat.

9. Do not defeat the safety purpose of the polarized or grounding-type plug.
A polarized plug has two blades with one wider than the other. A ground­ing type plug has two blades and a third grounding prong. The wide blade
or the third prong are provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for replacement of the obso­lete outlet.

10. Protect the power cord from being walked on or pinched particularly at
plugs, convenience receptacles, and the point where they exit from the
apparatus.

11. Only use attachments/accessories specified by the manufacturer.

12. Use only with the cart, stand, tripod, bracket, or table specified by the
manufacturer, or sold with the apparatus. When a cart is used, use caution
when moving the cart/apparatus combination to avoid injury from tip­over.

13. Unplug this apparatus during lightning storms or when unused for long
periods of time.

14. Refer all servicing to qualified service personnel. Servicing is required
when the apparatus has been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been spilled or objects have fallen into
the apparatus, the apparatus has been exposed to rain or moisture, does
not operate normally, or has been dropped.

Power Supply

L332-BN / L332-BP:

This camera must always be operated by AC 24 V or DC 12 V Certified/Listed,
class 2 power supply only.

L332-CP:

This camera must always be operated by AC 230 V.

Note:

Be careful of AC frequency when the camera is operated with Line lock mode.

Handling of the unit

Be careful not to spill water or other liquids on the unit. Be cautious not to get
combustible or metallic material inside the body. If used with foreign matter
inside, the camera is liable to fail or to get cause of fire or electric shock.

Remove dust or dirt on the surface of the lens with a blower.•

Use a dry soft cloth to clean the body. If it is very dirty, use a cloth damp-•
ened with a small quantity of neutral detergent then wipe dry.

Avoid the use of volatile solvents such as thinners, alcohol, benzene and •
insecticides.
They may damage the surface finish and/or impair the operation of the
camera.

Operating and storage location

Avoid viewing a very bright object (such as light fittings) during an extended
period. Avoid operating or storing the unit in the following locations.

Extremely hot or cold places (operating temperature •

-10 °C to 50 °C, however, we recommend that the unit be used within a
temperature range of 0 °C to 45 °C)

Damp or dust place•

Places exposed to rain•

Places subject to strong vibration•

Close to generators of powerful electromagnetic •
radiation such as radio or TV transmitters.

Specication

ITEM L332-BN L332-BP L332-CP

Signal System NTSC PAL

Total Pixels No./ Effective

Pixels No.

1028 x 508 / 976 x 494 1028 x 596 / 976 x 582

Image Device 6 mm CCD

DSP XDI-II

Lens CS Mount (C Mount using adaptor ring)

Digital Zoom X10

IRIS Control DC / ELC

Sync. System Internal / Line Lock

Scanning Frequency (H/V) 15.734 kHz / 59.94 Hz 15.625 kHz / 50 Hz

Horizontal Resolution 650 TV Lines

S/N Ratio 50 dB

Minimum Illumination

(Color, F1.2, 30 IRE)

Color : 0.0003 lx (Sens up Auto, F1.2)

B/W : 0.000 03 lx (Sens up Auto, F1.2)

Control Method Key button / RS-485

Video Output Signal 1 Vp-p Composite (75 Ω)

Day & Night DAY / NIGHT / AUTO / EXT

BACKLIGHT OFF / WDR / BLC / HSBLC

Motion detection SMART MD/REGIONAL MD/TAMPERING MD

3D-DNR OFF / LOW / MIDDLE / HIGH

Auto Gain Control OFF / LOW / MIDDLE / HIGH

ITEM L332-BN L332-BP L332-CP

Electronic Shutter Speed

1/60 to

1/120 000

1/50 to 1/120 000

Sens-Up OFF / AUTO

White Balance

ATW / AUTO / AWC b PUSH / MANUAL

Privacy Zone

Masking

RECTANGLE 8 AREAS

CIRCLE 2 AREAS

POLYGON 2 AREAS

Stabilizer( EIS) On / Off

Power Source DC 12 V / AC 24 V AC 230 V

Power Consumption 2.8 W

Operation / Storage Temp. -10 ˚C to 50 ˚C / -20 ˚C to 60 ˚C

Operation Humidity /

Storage

0 % RH to 80 % RH / 0 % RH to 85 % RH

Weight 363.5 g 442.5 g

Dimension (W x V x D) 67.4 mm X 61.5 mm X 134 mm

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equi­lateral triangle is intended to alert the user to the presence
of uninsulated dangerous voltage within the product’s
enclosure that may be of sufficient magnitude to constitute
a risk of electric shock to persons.

The exclamation point within an equilateral triangle is
intended to alert the user to the presence of important
operating and maintenance (servicing) instructions in the
literature accompanying the product.

FCC WARNING: This equipment may generate or use radio frequency energy.
Changes or modifications to this equipment may cause harmful interference
unless the modifications are expressly approved in the instruction manual. The
user could lose the authority to operate this equipment if an unauthorized
change or modification is made.

REGULATORY INFORMATION: FCC Part 15

This equipment has been tested and found to comply with the limits for a Class
A digital device, pursuant to Part 15 of the FCC Rules. These limits are designed
to provide reasonable protection against harmful interference when the equip­ment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and,
if not installed and used in accordance with the instruction manual, may cause
harmful interference to radio communications.
Operation of this equipment in a residential area is likely to cause harmful inter­ference in which case the user will be required to correct the interference at his
own expense.

A suitable conduit entries, knock-outs or glands shall be provided in the •
cable entries of this product in the end user.

Caution: Danger of explosion if battery is incorrectly replaced. Replaced •
only with the same or equivalent type recommended by the manufacturer.
Dispose of used batteries according to the manufacturer’s instructions.

Holes in metal, through which insulated wires pass, shall have smooth well •
rounded surfaces or shall be provided with brushings.

This Class A digital apparatus complies with Canadian ICES-003.
Cet appareil numérique de la classe A est conforme à la norme NMB-003 du
Canada.

Warning: Do not install this equipment in a confined space such as a bookcase
or similar unit.

Warning: Wiring methods shall be in accordance with the National Electric
Code, ANSI/NFPA 70.

Warning: This is a class A product. In a domestic environment this product
may cause radio interference in which case the user may be required to take
adequate measures.

Warning: To reduce a risk of fire or electric shock, do not expose this product to
rain or moisture.

Caution: This installation should be made by a qualified service person and
should conform to all local codes.

Caution: To avoid electrical shock, do not open the cabinet. Refer servicing to
qualified personnel only.

Caution: The apparatus shall not be exposed to water (dripping or splashing)
and no objects filled with liquids, such as vases, shall be placed on the appara­tus.

To disconnect power from mains, pull out the mains cord plug. When install­ing the product, ensure that the plug is easily accessible.

LG Electronics hereby declares that this/these product(s) is/are in
compliance with the essential requirements and other relevant pro­visions of Directive 2004/108/EC, 2006/95/EC, and 2009/125/EC.

European representative :

LG Electronics Service Europe B.V.
Veluwezoom 15, 1327 AE Almere,
The Netherlands (Tel : [phone])

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to
a product it means the product is covered by the European
Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of
separately from the municipal waste stream via designated
collection facilities appointed by the government or the local
authorities.

3. The correct disposal of your old appliance will help prevent
potential negative consequences for the environment and
human health.

4. For more detailed information about disposal of your old
appliance, please contact your city office, waste disposal
service or the shop where you purchased the product.

EEE Compliance with Directive. (for Turkey only)

a

Install the camera and mounting brack­et securely.

<FRANÇAIS> Installez solidement la caméra et le support de montage.

<ITALIANO> Montare la videocamera alla staffa in maniera sicura.

<ČEŠTINA> Připevněte řádně kameru a mechanismus pro uchycení.

<POLSKI>

Zamontować dokładnie kamerę oraz wspornik
montażowy.

<ESPAÑOL> Monte la cámara y el soporte.

<NEDERLANDS>

Zet de camera en de montagebeugel stevig vast.

<PORTUGUÊS> Instale a câmera e o suporte de montagem firmemente.

b

Install the C or CS mount type lens.

<FRANÇAIS> Installez l’objectif à monture C ou CS.

<ITALIANO> Installare un obiettivo di tipo C o CS.

<ČEŠTINA> Nainstalujte připevňovací čočky typu C nebo CS.

<POLSKI> Mailować obiektyw typu C lub CS.

<ESPAÑOL> Instale un objetivo C o CS.

<NEDERLANDS>

Monteer een C-mount- of CS-mount-objectief (‘lens’).

<PORTUGUÊS> Instale as lentes de montagem do tipo C ou CS.

c

Install the camera and mounting arm.

<FRANÇAIS> Installez la caméra et le bras de montage.

<ITALIANO> Montare la videocamera al braccio.

<ČEŠTINA> Připevněte kameru a připevňovací rameno.

<POLSKI> Zamontować kamerę oraz ramię montażowe.

<ESPAÑOL> Monte la cámara y el brazo de soporte.

<NEDERLANDS>

Monteer de camera en de montagearm.

<PORTUGUÊS> Instale a câmera e o braço de montagem.

d

Connect the power and monitor.

<L332-BN/L332-BP> <L332-CP>

TRX -

TRX +

TRX -

TRX +

<FRANÇAIS> Raccordez l’alimentation et le moniteur.

<ITALIANO> Collegare l’alimentazione e il monitor.

<ČEŠTINA> Zapojte proud a monitor.

<POLSKI> Podłączyć zasilanie oraz monitor.

<ESPAÑOL> Conecte el monitor y la fuente de alimentación.

<NEDERLANDS>

Sluit de voeding en de monitor aan.

<PORTUGUÊS> Ligue a alimentação e o monitor.

Installation Guide

Flange-back Adjustment

e

Connect the external device.

TRX -

TRX +

RS-485 Unit

External D&N

Switch

<FRANÇAIS> Raccordez l’appareil externe.

<ITALIANO> Collegare la periferica esterna.

<ČEŠTINA> Připojte externí zařízení.

<POLSKI> Podłącz urządzenie zewnętrzne.

<ESPAÑOL> Conecte el dispositivo externo.

<NEDERLANDS>

Sluit het externe apparaat aan.

<PORTUGUÊS> Ligar o dispositivo externo.

Loosen the flange-back fixing lever. Up and down the
flange-back adjusting lever to obtain a focused point.

<To loosen the lever.> <To adjust the focus.>

<FRANÇAIS>

Desserrez le levier de fixation de l’embase. Levez ou abaissez le
levier de réglage de l’embase pour obtenir un point net.

<ITALIANO>

Allentare la leva per il fissaggio della flangia posteriore.
Sollevare e abbassare la leva di regolazione della flangia poste­riore per ottenere un punto di messa a fuoco.

<ČEŠTINA>

Povolte zpětnou přírubu upevňovací páčky. Pohybujte směrem
nahoru a dolů zpětnou upevňovací páčkou pro získání
zaměřovacího bodu.

<POLSKI>

Poluzować dźwignię mocowania kołnierza. Aby uzyskać punkt
ogniskowania poruszyć dźwignią regulacji kołnierza do góry i
na dół.

<ESPAÑOL>

Afloje la palanca de fijación. Suba o baje la palanca de ajuste
para obtener un punto de enfoque

<NEDERLANDS>

Maak de flange-back bevestigingshendel los. Beweeg de
flange-back instelheldel op en neer om een scherpstelpunt te
bereiken.

<PORTUGUÊS>

Afrouxe o nivelador de fixação da flange traseira. Suspenda e
abaixe o nivelador de fixação da flange traseira para obter o
ponto do foco.

OSD Menu Overview

Main Menu Sub Menu Contents

CAMERA ID - OFF, 1 to 255

EXPOSURE ALC/ ELC

WDR/BLC OFF/WDR/BLC/HSBLC

BRIGHTNESS 0 to 100

AGC OFF/LOW/MIDDLE/HIGH

SHUTTER

X512, ... , x2, AUTO, OFF, A.FLK, 1/160, ... ,

1/120 000

SENS-UP

OFF

AUTO (X2 , ... , X128)

EXIT RET/TOP/END

WHITE BAL

ATW USER MODE NATURAL/COOL/WARM/VIVID

AUTO USER MODE NATURAL/COOL/WARM/VIVID

AWC b PUSH

MANUAL

COLOR TEMP INDOOR, OUTDOOR

RED -100 to 100

BLUE -100 to 100

EXIT RET/TOP/END

DAY/NIGHT

AUTO

LEVEL LOW/ MIDDLE/ HIGH

DWELL TIME 5, 10, 15 SEC.

EXIT RET/TOP/END

EXT

DAY

NIGHT

MOTION DET

ON

SMART MD ON/OFF

REGIONAL MD

ON

ZONE NUMBER

AREA1 to

AREA4

ZONE STATE ON/OFF

HEIGHT 2 to 6

WIDTH 2 to 8

MOVE Y 1 to 5

MOVE X 1 to 7

EXIT RET/TOP/END

OFF

TAMPERING MD ON/OFF

SENSITIVITY 0 to 100

EXIT

RET/TOP/

END

OFF

Main Menu Sub Menu Contents

3D-DNR

OFF -

LOW -

MIDDLE -

HIGH -

PRIVACY

OFF -

ON

COLOR RED, GREEN, BLUE 0 to 255

TRANSPARENCY 0 to 16 -

RECTANGLE

MASK NUMBER AREA1 to AREA8

RECT. DISPLAY ON/OFF

HEIGHT 4 to 100

WIDTH 4 to 100
MOVE Y 2 to 98
MOVE X 2 to 98

CIRCLE

MASK NUMBER AREA1 to AREA2

CIR. DISPLAY ON/OFF

HEIGHT 1 to 15

WIDTH 1 to 15
MOVE Y 0 to 100
MOVE X 0 to 100

RADIUS SIZE 0 to 100

POLYGON

MASK NUMBER AREA1 to AREA2

POLY. DISPLAY ON/OFF
POLYGON DRAW ­POLYGON MOVE -

SPECIAL

D-ZOOM

OFF

ON

ZOOM

PAN
TILT
EXIT

D-EFFECT OFF/ MIRROR/ ROTATE/ V-FLIP

SHARPNESS 0 to 68

COLOR OFF/ ON

STABILIZER OFF/ ON

SYNC INT / LL

USER TITLE OFF/ ON

LANGUAGE

ENG (The supported language can be different depending on

the model.)

EXIT RET/TOP/END

RESET

CAMERA REBOOT -

FACTORY RESET -

COMMUNICATION

PROTOCOL
BAUD RATE

SAVE & REBOOT

EXIT RET/TOP/END

EXIT RET/TOP/END

EXIT -

Menu Operation