LG L1730SF User Manual

User’s Guide

L1730SF

Make sure to read the Important Precautions before using the product.

Keep the User's Guide(CD) in an accessible place for furture reference.

See the label attached on the back cover and quote this information to your

dealer when you require service.

Important Precautions

This unit has been engineered and manufactured to ensure your personal
safety, however improper use may result in potential eletrical shock or fire
hazards. In order to allow the proper operation of all safeguards
incorporated in this display, observe the following basic rules for its
installation, use, and servicing.

On Safety

Use only the power cord supplied with the unit. In case you use another power
cord, make sure that it is certified by the applicable national standards if not being
provided by the supplier. If the power cable is faulty in any way, please contact the
manufacturer or the nearest authorized repair service provider for a replacement.

The power supply cord is used as the main disconnection device. Ensure that the
socket-outlet is easily accessible after installation.

Operate the display only from a power source indicated in the specifications of
this manual or listed on the display. If you are not sure what type of power supply
you have in your home, consult with your dealer.

Overloaded AC outlets and extension cords are dangerous. So are frayed power
cords and broken plugs. They may result in a shock or fire hazard. Call your service
technician for replacement.

Do not Open the Display.

There are no user serviceable components inside.
There are Dangerous High Voltages inside, even when the power is OFF.
Contact your dealer if the display is not operating properly.

To Avoid Personal Injury :

Do not place the display on a sloping shelf unless properly secured.
Use only a stand recommended by the manufacturer.

To Prevent Fire or Hazards:

Always turn the display OFF if you leave the room for more than a short period
of time. Never leave the display ON when leaving the house.
Keep children from dropping or pushing objects into the display's cabinet
openings. Some internal parts carry hazardous voltages.
Do not add accessories that have not been designed for this display.
During a lightning storm or when the display is to be left unattended for an
extended period of time, unplug it from the wall outlet.

A1

Important Precautions

On Installation

Do not allow anything to rest upon or roll over the power cord, and do not place
the display where the power cord is subject to damage.

Do not use this display near water such as near a bathtub, washbowl, kitchen
sink, laundry tub, in a wet basement, or near a swimming pool.
Displays are provided with ventilation openings in the cabinet to allow the release
of heat generated during operation. If these openings are blocked, built-up heat
can cause failures which may result in a fire hazard. Therefore, NEVER:

Block the bottom ventilation slots by placing the display on a bed, sofa, rug, etc.
Place the display in a built-in enclosure unless proper ventilation is provided.
Cover the openings with cloth or other material.
Place the display near or over a radiator or heat source.

Do not rub or strike the Active Matrix LCD with anything hard as this may scratch,
mar, or damage the Active Matrix LCD permanently.

Do not press the LCD screen with your finger for a long time as this may cause
some afterimages.

Some dot defects may appear as Red, Green or Blue spots on the screen.
However, this will have no impact or effect on the display performance.

If possible, use the recommended resolution to obtain the best image quality for
your LCD display. If used under any mode except the recommended resolution,
some scaled or processed images may appear on the screen. However, this is
characteristic of the fixed-resolution LCD panel.

On Cleaning

Unplug the display before cleaning the face of the display screen.
Use a slightly damp (not wet) cloth. Do not use an aerosol directly on the display

screen because over-spraying may cause electrical shock.

On Repacking

Do not throw away the carton and packing materials. They make an ideal
container in which to transport the unit. When shipping the unit to another
location, repack it in its original material.

On Disposal

The fluorescent lamp used in this product contains a small amount of mercury.
Do not dispose of this product with general household waste.

Disposal of this product must be carried out in accordance to the regulations of
your local authority.

A2

Connecting the Display

Before setting up the monitor, ensure that the power to the monitor, the
computer system, and other attached devices is turned off.

Positioning your display

1. Remove the tape.

<Image 1>

Put the set as the
picture below
<Image 1> to
remove the tape.

<Image 2>

Do not remove the tape
with the set up side
down as the <Image 2>
The base part may
spring up to injure your
hand.

2. Adjust the position of the panel in various ways for maximum comfort.

Tilt Range : -20˚~140˚

140˚ -20˚

Ergonomic

It is recommended that in order to maintain an ergonomic and comfortable viewing
position, the forward tilt angle of the monitor should not exceed 5 degrees.

Height Range : maximum 2.41inch (61.3mm)

Landscape & Portrait : You can rotate the panel 90

(* For detailed information, please refer to the Pivot Sofeware CD provided.)

* Make sure not to

touch the floor
when the head
rotates to use the
Pivot function.

o

clockwise.

A3

Connecting the Display

Using the Computer

1. Connect the signal cable. When attached, tighten the thumbscrews to secure

the connection.

2. Connect the power cord into a proper power outlet that is easily accessible and

close to the display.

NOTE

This is a simplified representation of the rear view.
This rear view represents a general model; your display may differ from the view as shown.

Power Cord

Signal Cable

D-sub

Wall-outlet type

PC-outlet type

Mac adapter

For Apple Macintosh use, a separate plug adapter is needed to
change the 15 pin high density (3 row) D-sub VGA connector on
the supplied cable to a 15 pin 2 row connector.

3. Press button on the front switch panel to turn the

power on. When monitor power is turned on, the 'Self
Image Setting Function' is executed automatically.

(Only analog mode)

NOTE

‘ Self Image Setting Function’? This function provides the user with optimal display settings.When the user

connects the monitor for the first time, this function automatically adjusts the display to optimal settings for
individual input signals. If you want to adjust the monitor while in use, or wish to manually run this function once
again, push the ‘SET/AUTO’ button on the front panel of the monitor. Otherwise, you may execute the ‘ Factory
reset’ option on the OSD adjustment menu. However, be aware that this option initializes all the menu items except
‘Language’.

A4

Connecting the Display

To Use Touch Screen

Select and Install the driver CD provided.

ITM DRIVER

1) Insert the driver installation CD for the ITM touch screen.

2) See the touch screen software installation CD for more
information and assistance.

3) Connect the USB cable or the RS-232C cable for the touch screen
after the driver installation.

* The software drivers support the following Microsoft Windows

operating systems: Windows 95, 98, Me, and NT 4.0.

Make sure you have the
driver installation CD
bundled with the product.

Hantouch DRIVER

1) Connect the USB cable or the RS-232C cable for touch screen before
installing the driver.

2) Insert the Hantouch touch screen driver installation CD.

3) Open the [My Computer] -> [LG Driver] -> [Drivers] folder, then select the
driver appropriate for your OS.

4) For more information, see the installation manual in the touch screen
software installation CD bundled with the product.

* The software drivers support the following Microsoft Windows operating

systems: Windows 95, 98, Me, and NT 4.0.

For more information about installation for other OS, see the driver

installation CD.

* Do not select "install PS/2 interface driver" while
installing the touch screen driver for the Hantouch.

A5

Connecting the Display

<

USB cable for the touch screen

>

Power

Cord

Power

Cord

Touch

Screen

USB

<

RS-232C cable for the touch screen

Touch
Screen

RS-232C

Signal

Cable

Signal

Cable

RS-232C

Touch Screen

USB

RS-232C

>

Touch Screen

RS-232C

NOTE

Your purchased product and its accessories may look different from the items

illustrated in this manual.

A6

Control Panel Functions

MENU

SET/AUTO

-

+

Front Panel Controls

Bottom

Control Function

MENU Button

Buttons

Use this button to enter or exit the On Screen Display.

OSD LOCKED/UNLOCKED

This function allows you to lock the current control
settings, so that they cannot be inadvertently changed.
Press and hold the MENU button for 5 seconds. The
message "OSD LOCKED" should appear.

You can unlock the OSD controls at any time by pushing
the MENU button for 5 seconds. The message "OSD
UNLOCKED" should appear.

Use these buttons to select or adjust functions in the On
Screen Display.

For more information, refer to page A14.

A7