LG IPS225VX, IPS235VX User Manual
ENGLISH
MODEL NO.:
IPS235*X
IPS225*X
OWNER’S MANUAL
LCD MONITOR
Please read this manual carefully before operating the
your set and retain it for future reference.
LCD MONITOR MODEL
IPS225V
IPS235V
www.lg.com
TABLE OF CONTENTS
2
ENGLISH
ENG
CONTENTS
3 ASSEMBLING AND PREPARING
3 Unpacking
4 Parts and buttons
6 Setting up the Monitor set
6 - Attaching the Stand Base
6 - Detaching the Stand Base
7 - Mounting on a table
8 - Mounting on a wall
10 USING THE MONITOR SET
10 Connecting to a PC
10 - D-SUB connection
10 - DVI-D connection
10 - HDMI connection
12 CUSTOMIZING SETTINGS
20 TROUBLESHOOTING
22 SPECIFICATIONS
IPS225V
22
IPS235V
23
24 P
24
reset Modes (Resolution)
Indicator
12 Accessing The Main Menus
13 Customizing Settings
13 - Menu Settings
14 - PICUURE
15 -
16
16
17
18
19
COLOR
-DISPLAY
-VOLUME
-OTHERE
MODE Setting
DUAL PACKAGE Setting
ASSEMBLING AND PREPARING
Stand Base
and accessories.
3
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local
dealer where you purchased your product. The illustrations in this manual may differ from the actual product
CD(Owner's Manual) /
Card
D-SUB Cable
(This signal cable may be attached
to this product before shipping out.)
(This cable is not included in all
Power Cord
DVI-D Cable
countries.)
ENGLISH
ENG
CAUTION
Do not use any unapproved accessories to ensure the safety and product life span.
y
Any damages or injuries by using unapproved accessories are not covered by the warranty.
y
NOTE
The accessories supplied with your product may vary depending on the model.
y
Product specifications or contents in this manual may be changed without prior notice due to upgrade
y
of product functions.
User should use shielded signal interface cables (RGB cable / DVI-D cable) with ferrite cores to
y
maintain standard compliance for the product.
ENGLISH
ENG
ASSEMBLING AND PREPARING
4
Parts and buttons
Power Indicator
Lighting On: Turned on
�
Lighting Off: Turned off
AC-IN/
电源输入
(Power Button)
Button (See p.13)
HDMID-SUB DVI-D
Connection panel (See p.10)
Button Description
MENU Accesses the main menus.(See p.13)
MODE
OSD LOCKED/
UNLOCKED
Use this button to enter USER, MOVE,TEXT, PHOTO,sRGB menus.(See p.18)
This function allows you to lock the current control settings, so
that they cannot be inadvertently changed.
Press and hold the MENU button for several seconds.
The message "OSD LOCKED" should appear.
You can unlock the OSD controls at any time by pushing
the MENU button for several seconds. The message "OSD
UNLOCKED" should appear.
ASSEMBLING AND PREPARING
5
ENGLISH
ENG
DUAL
AUTO
INPUT You can choose the input signal.
EXIT Exit the OSD(On Screen Display).
(Power Button)
Use this button to enter DUAL MONITOR and DUAL WEB menus.(See p.19)
When adjusting your display settings, always press the AUTO button on the MONITOR
SETUP OSD. (Only supported in Analog Mode)
The best display mode 1920 x 1080
�When two input signals are connected, you can select the input signal (D-SUB/DVI/
HDMI) you want.
�When only one signal is connected, it is automatically detected. The default setting is
D-SUB.
Turns the power on or off.
Power Indicator The power indicator stays blue if the display is running
properly (On Mode). If the display is in Sleep Mode, the power
indicator blinks blue.
ASSEMBLING AND PREPARING
6
ENGLISH
ENG
Setting up the Monitor set
Attaching the Stand Base
Place the Monitor set with the screen side
1
down on a flat and cushioned surface.
CAUTION
Lay a foam mat or soft protective cloth
on the surface to protect the screen from
damage.
Attach the Stand Base and then tighten the
2
screw to the right with a Coin.
Detaching the Stand Base and Body
Place the Monitor set with the screen side
1
down on a flat and cushioned surface.
Turn the screw to the left, and then pull out the
2
Stand Base from the Stand Body.
Stand Base
Stand Base
CAUTION
This illustration depicts the general model of
connection. Your monitor may differ from the
items shown in the picture.
Do not carry the product upside down
holding only the stand base. The product
may fall and get damaged or injure your
foot.
ASSEMBLING AND PREPARING
7
Mounting on a table
Lift and tilt the Monitor set into its upright
1
position on a table.
Leave a 10 cm (minimum) space from the wall
for proper ventilation.
10 cm
10 cm
10 cm
10 cm
WARNING
When you adjust the angle, do not hold the
buttom of the Monitor set frame as shown on
the following illustration, as may injure your
fingers.
Do not touch or press the screen when
adjusting the angle of the monitor.
ENGLISH
ENG
Connect the Power Cord to a wall outlet.
2
Press (Power) button on the front switch
3
panel to turn the power on.
CAUTION
Unplug the power cord before moving the
Monitor to another location. Otherwise electric
shock may occur.
NOTE
Tilt from +15 to -5 degrees up or down to adjust
the angle of the Monitor set to suit your view.
5 - 51
Front Rear
ASSEMBLING AND PREPARING
8
ENGLISH
ENG
Using the Kensington security system
The Kensington security system connector is
located at the back of the Monitor set. For more
information of installation and using, refer to the
manual supplied with the Kensington security
system or visit
Connect the Kensington security system cable
between the Monitor set and a table.
http://www.kensington.com
.
Mounting on a wall
For proper ventilation, allow a clearance of 10 cm
on each side and from the wall. Detailed
instructions are available from your dealer, see the
optional Tilt Wall Mounting Bracket Installation and
Setup Guide.
10 cm
10 cm
10 cm
10 cm
NOTE
The Kensington security system is optional.
You can obtain it from most electronics stores.
When you install the Monitor set using a wall
mounting interface (optional parts), attach it
carefully so it will not drop.
Please use VESA standard as below.
784.8 mm (30.9 inch) and under
y
* Wall Mount Pad Thickness : 2.6 mm
* Screw : Φ 4.0 mm x Pitch 0.7 mm x
Length 10 mm
787.4 mm (31.0 inch) and above
y
* Please use VESA standard wall mount pad
and screws.
Loading...