LG IPS225PX User Manual

ENGLISH

OWNER’S MANUAL

LCD MONITOR

Please read this manual carefully before operating your set and retain it for future reference.

LCD MONITOR MODEL

IPS225P IPS235P

www.lg.com

Important Precautions

NOTE

THE MANUFACTURER IS NOT RESPONSIBLE FOR ANY RADIO OR TV INTRERFERENCE CAUSED BY UNAUTHORIZED MODIFICATIONS TO THIS

EQUIPMENT.SUCH MODIFICATIONS COULD VOID THE USER'S AUTHORITY

NOTE

This epuipment has been tested and found to comply with the limits for a class B digital device,pursuant to part 15 of the FCC Rules.These limits are designed

to provide reasonable protection against harmful interference in a residential installation.This equipment generates,uses and can radiate radio frequency

-Increase the separation between the equipment and the receiver.

-Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

energy and,if not installed and used in accordance with the instructions,may

TO OPERATE THE EQUIPMENT.

-Consult the dealer or an experienced radio/TV technician for help.

cause harmful interference to radio communications.However,there is no guarantee that interference will not occur in a particular installation.If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on,the user is encouraged to try to correct the interference by one or more of the following

measures:

-Reorient or relocate the receiving antenna.

TABLE OF CONTENTS

ENGLISH

ENG

3 ASSEMBLING AND

PREPARING

3 Unpacking 4 Parts and buttons 6 Setting up the Monitor set 6 - Attaching the Stand Base 6 - Detaching the Stand Base 7 - Mounting on a table 8 - Mounting on a wall

10 USING THE MONITOR SET

10 Connecting to a PC 10 - D-SUB connection 10 - DVI-D connection 10 - HDMI connection

20 TROUBLESHOOTING

22 SPECIFICATIONS

22 IPS225P 23 IPS235P 24 Preset Modes (Resolution) 24 Indicator

12 CUSTOMIZING SETTINGS

12 Accessing The Main Menus 13 Customizing Settings 13 - Menu Settings 14 - PICTURE 15 - COLOR 16 - DISPLAY 16 - VOLUME 17 - OTHERS 18

MODE Setting

19 DUAL PACKAGE Setting

ASSEMBLING AND PREPARING

User must use shielded signal interface cables (D-sub 15 pin cable, DVI-D cable) with ferrite cores (core in the connector) to maintain standard compliance for the product。

ASSEMBLING AND PREPARING

Unpacking

Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.

CD(Owner's Manual) /

Card

D-SUB Cable

(This signal cable may be attached

to this product before shipping out.)

(This cable is not included in all

Power Cord

DVI-D Cable

countries.)

ENGLISH

ENG

Stand Base

Display Quality Assurance Report

CAUTION

Do not use any unapproved accessories to ensure the safety and product life span.

Any damages or injuries by using unapproved accessories are not covered by the warranty.

NOTE

The accessories supplied with your product may vary depending on the model.

Product specifications or contents in this manual may be changed without prior notice due to upgrade

of product functions.

ENGLISH

Power Indicator

Lighting On: Turned on Lighting Off: Turned off

Button (See p.13)

(Power Button)

Connection panel (See p.10)

ENG

ASSEMBLING AND PREPARING

Parts and buttons

y y

ASSEMBLING AND PREPARING

Button Description

MENU Accesses the main menus.(See p.13)

OSD LOCKED/ UNLOCKED

MODE Use this button to enter USER, MOVIE,TEXT,PHOTO,sRGB menus.(See p.18) DUAL Use this button to enter DUAL MONITOR and DUAL WEB menus.(See p.19) AUTO When adjusting your display settings, always press the AUTO button on the MONITOR

INPUT You can choose the input signal.

EXIT Exit the OSD(On Screen Display).

(Power Button)

SETUP OSD. (Only supported in Analog Mode) The best display mode 1920 x 1080

• When two input signals are connected, you can select the input signal (D-SUB/DVI/

HDMI) you want.

• When only one signal is connected, it is automatically detected. The default setting is

D-SUB.

Turns the power on or off.

Power Indicator The power indicator stays blue if the display is running

This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear.

properly (On Mode). If the display is in Sleep Mode, the power indicator blinks blue.

ENGLISH

ENG

ASSEMBLING AND PREPARING

Stand Base

ENGLISH

ENG

Setting up the Monitor set

Attaching the Stand Base

Place the Monitor set with the screen side

down on a flat and cushioned surface.

CAUTION

Lay a foam mat or soft protective cloth on the surface to protect the screen from damage.

Attach the Stand Base and then tighten the

screw to the right with a Coin.

Detaching the Stand Base

Place the Monitor set with the screen side

down on a flat and cushioned surface.

Turn the screw to the left, and then pull out the

Stand Base from the Stand Body.

CAUTION

This illustration depicts the general model of

connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding

only the stand base. The product may fall and get damaged or injure your foot.

ASSEMBLING AND PREPARING

* Please be sure to

remove the Locking pin to adjust the height.

5 - 51

130.0 mm

Mounting on a table

Lift and tilt the Monitor set into its upright

position on a table. Leave a 10 cm (minimum) space from the wall

for proper ventilation.

10 cm

NOTE

Tilt from +15 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view.

Front Rear

Swivel Range : - 45˚(+/- 2°)

ENGLISH

ENG

Connect the Power Cord to a wall outlet.

Press (Power) button on the front switch

panel to turn the power on.

CAUTION

Unplug the power cord before moving the Monitor to another location. Otherwise electric shock may occur.

45˚(+/- 2°)

Height Range : maximum 5.12 inches (130.0 mm)

ASSEMBLING AND PREPARING

ENGLISH

ENG

Using the Kensington security system

The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit

Connect the Kensington security system cable between the Monitor set and a table.

http://www.kensington.com

NOTE

WARNING

When adjusting the angle of the screen, do not put your finger(s) in between the head of the monitor and the stand body. You can hurt your finger(s).

When adjusting the height of the screen, do not put your finger(s) in between the head of the monitor and the stand base. You can hurt your finger(s).

WARNING

You do not need to replace the Locking pin after it

is removed, to adjust its height.

ERGONOMIC

It is recommended that in order to maintain an erg-

onomic and comfortable viewing position, the forw-

ard tilt angle of the monitor should not exceed 5 degrees.

The Kensington security system is optional. You can obtain it from most electronics stores.

+ 18 hidden pages