LG HT762TZ-D0 User Manual

DVD/CD RECEIVER OWNER’S MANUAL

MODEL: HT762TZ

HT762TZ-D0 SH72TZ-S SH72TZ-C SH72TZ-W

Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely.

HT762TZ-D0_DROMLLK_ENG_3995

This lightning flash with arrowhead symbol within an equilateral triangle is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product.

WARNING: Do not install this equipment in a confined space such as a book case or similar unit.

CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer's instructions.

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating. The openings should be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer's instruction have been adhered to.

CAUTION:

This product employs a Laser System. To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference. Should the unit require maintenance, contact an authorized service center. Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure. To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.

CAUTION: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.

CAUTION concerning the Power Cord Most appliances recommend they be placed upon

a dedicated circuit;

That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.

Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.

Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.

To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

This product is manufactured to comply with the EEC DIRECTIVE 2004/108/EC and 2006/95/EC.

CLASS 1 LASER PRODUCT KLASSE 1

LASER PRODUKT LUOKAN 1 LASER LAITE KLASS 1

LASER APPARAT CLASSE 1

PRODUIT LASER

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK

OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK)

NO USER-SERVICEABLE PARTS INSIDE

REFER SERVICING TO QUALIFIED SERVICE

PERSONNEL.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

Introduction

Maintenance and Service . . . . . . . . . . . . . . . . .3

Before use . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4

Front Panel/Rear Panel . . . . . . . . . . . . . . . . . . .5

Remote Control . . . . . . . . . . . . . . . . . . . . . . . . .6

Installation and Setup

TV Connection . . . . . . . . . . . . . . . . . . . . . . . . . .7

Optional Equipment Connection . . . . . . . . . . . .8

Antenna Connection . . . . . . . . . . . . . . . . . . . . .8

Assembling the speaker stand to the speaker .9

Speaker System Connection . . . . . . . . . . . . . . .9

HDMI Connection . . . . . . . . . . . . . . . . . . . . . .10

Displaying Disc Information on-screen . . . . . .11

Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . .11

General Operation . . . . . . . . . . . . . . . . . . . .11-14

LANGUAGE . . . . . . . . . . . . . . . . . . . . . . . . .11

DISPLAY . . . . . . . . . . . . . . . . . . . . . . . . . . . .12

AUDIO . . . . . . . . . . . . . . . . . . . . . . . . . . . . .13

5.1 Speaker Setup . . . . . . . . . . . . . . . . . . . . .13

LOCK (Parental Control) . . . . . . . . . . . . . . . .14

OTHERS . . . . . . . . . . . . . . . . . . . . . . . . . . . .14

Operation

General features . . . . . . . . . . . . . . . . . . . . . . .15

Additional features . . . . . . . . . . . . . . . . . . . . .16

Controlling the TV . . . . . . . . . . . . . . . . . . . . . .16

Playing an Audio CD or MP3/WMA file . . . . . .17

Programmed Playback . . . . . . . . . . . . . . . . . .17

Viewing a JPEG file . . . . . . . . . . . . . . . . . . . .18

Playing a DivX Movie file . . . . . . . . . . . . . . . .19

Presetting the Radio Stations . . . . . . . . . . . . .20

Listening to the Radio . . . . . . . . . . . . . . . . . . .20

RDS Operation . . . . . . . . . . . . . . . . . . . . . . . . .21

DVD Audio Discs . . . . . . . . . . . . . . . . . . . . . . .22

Sleep Timer Setting . . . . . . . . . . . . . . . . . . . . .23

Dimmer . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Selecting input source . . . . . . . . . . . . . . . . . . .23

XTS/XTS pro . . . . . . . . . . . . . . . . . . . . . . . . . . .23

VIRTUAL sound . . . . . . . . . . . . . . . . . . . . . . . .23

Sound Mode . . . . . . . . . . . . . . . . . . . . . . . . . . .23

Reference

Language Codes . . . . . . . . . . . . . . . . . . . . . . .24

Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . .24

Troubleshooting . . . . . . . . . . . . . . . . . . . . .25-26

Specifications . . . . . . . . . . . . . . . . . . . . . . . . .27

Maintenance and Service

Refer to the information in this chapter before contacting a service technician.

Handling the unit

When shipping the unit

Please save the original shipping carton and packing materials. If you need to ship the unit, for maximum protection, re-pack the unit as it was originally packed at the factory.

Keeping the exterior surfaces clean



Do not use volatile liquids such as insecticide spray near the unit.



Do not leave rubber or plastic products in contact with the unit for a long period of time. since they leave marks on the surface.

Cleaning the unit

To clean the player, use a soft, dry cloth. If the surfaces are extremely dirty, use a soft cloth lightly moistened with a mild detergent solution.

Do not use strong solvents such as alcohol, benzine, or thinner, as these might damage the surface of the unit.

Maintaining the Unit

The DVD/CD Receiver is a high-tech, precision device. If the optical pick-up lens and disc drive parts are dirty or worn, the picture quality could be diminished.

Depending on the operating environment, regular inspection and maintenance are recommended after every 1,000 hours of use.

For details, please contact your nearest authorized service center.

Before use

To ensure proper use of this product, please read this owner’s manual carefully and retain it for future reference.

This manual provides information on the operation and maintenance of your DVD/CD Receiver. Should the unit require service, contact an authorized service location.

About the Symbol Display

“ ” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that specific DVD video disc.

Symbol Used in this Manual

Note:

Indicates special notes and operating features.

Tip:

Indicates tips and hints for making the task easier.

A section whose title has one of the following symbols is applicable only to the disc represented by the symbol.

DVD Audio CDs MP3 files WMA files JPEG files DivX files

Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories. Confidential Unpublished works. Copyright 1992-1997 Dolby Laboratories. All rights reserved.

Manufactured under license from Digital Theater Systems, Inc. U.S. Pat. No’s. 5,451,942; 5,956,674; 5,974,380; 5,978,762; 6,226,616; 6,487,535 and other U.S. and worldwide patents issued and pending. "DTS" and "DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc. Copyright 1996, 2003 Digital Theater Systems, Inc. All Rights Reserved.

Types of Playable Discs

DVD (8 cm / 12 cm disc)

Audio CD (8 cm / 12 cm disc)

In addition, this unit can play a DVD±R, DVD±RW and CD-R or CD-RW that contains audio titles, MP3, WMA, JPEG or DivX files.

Notes:



Depending on the conditions of the recording equipment or the CD-R/RW (or DVD-RW, DVD+RW) disc itself, some CD-R/RW (or DVD-RW, DVD+RW) discs may not be played on the unit.



Do not attach any seal or label to either side (the labeled side or the recorded side) of a disc.



Do not use irregularly shaped CDs (e.g., heartshaped

or octagonal). It may result in malfunctions.

Regional Code

This unit has a regional code printed on the rear of the unit. This unit can play only DVD discs labelled as the same as the rear of the unit or “ALL”.

Notes on Regional Codes



Most DVD discs have a globe with one or more numbers in it clearly visible on the cover. This number must match your DVD player’s regional code or the disc cannot play.



If you try to play a DVD with a different regional code from your player, the message “Check Regional Code” appears on the TV screen.

DivX

JPEG

WMA

MP3

ACD

DVD

Introduction

What is SIMPLINK?

Some functions of this unit are controlled by TV’s remote control when this unit and LG TV with SIMPLINK are connected through HDMI connection.

• Controllable functions by LG TV’s remote control; Play, Pause, Scan, Skip, Stop, Power Off, etc.

• Refer to the TV owner’s manual for the details of SIMPLINK function.

• LG TV with SIMPLINK function has the logo as shown above.

• Use a higher version cable than 1.2A HDMI cable.

Introduction

Do not touch the inner pins of the jacks on the rear panel. Electrostatic discharge may cause permanent damage to the unit.

HDMI OUTHDMI OUT

OUT PUT

INPUT

L - AUX - R

MONITOR

COMPONENT VIDEO (PROGRESSIVE SCAN)

FM Antenna connector

AM Loop Antenna connectors

SPEAKER connectors

Power Cord

MONITOR OUT connector

COMPONENT VIDEO OUT terminals

Connect to a TV with Y PB PR inputs.

Front Panel/Rear Panel

OUTPUT (TO TV) EURO AV socket

Connect to a TV with SCART jack.

Cooling fan

OPTICAL IN connector

AUX AUDIO Input (L/R) connector

VIDEO OUT SELECTOR switch

HDMI OUT

HDMI output providing a high quality

interface for digital audio and video.

OPEN/CLOSE button

TUNING(-/+)/SKIP/ SEARCH(../>>)

Remote sensor

AUDIO IN connector

VOLUME controller

POWER

DISPLAYWindow

DISC Tray

USB port

Connect to a USB port of a memory device (USB memory etc.)

FUNC.(-)/PLAY(B)

Press and hold down this button about 3 seconds, then press repeatedly to select other function.

PAUSE (XX)/ MONO/STEREO (ST.)

STOP (x)

Remote Control

Remote Control Operation Range

Point the remote control at the remote sensor and press the buttons.



Distance: About 23 ft (7 m) from the front of the remote sensor



Angle: About 30° in each direction in front of the remote sensor

Remote control battery installation

Remove the battery cover on the rear of the remote control, and insert two R06 (size

AA) batteries with and aligned correctly.

Caution

Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.).

OPEN/CLOSE (ZZ)

Opens and closes

the disc tray.

DVD

Selects the output source (CD/DVD).

PROG./MEMO.

Accesses or removes Program menu. Enter a radio station’s frequency into the tuner.

S-TITLE

Selects a subtitle language (DVD).

CLEAR

Removes a track number on the program menu or a mark on the MARKER SEARCH menu.

MARKER

Marks a point during playback.

Displays MARKER SEARCH menu.

SCAN/SLOW(bb/BB)

Searches backward or forward. Reverse/ Forward slow playback.

REVERSE/FORWARD SKIP (../>>)

TITLE

Displays the disc’s Title menu, if available.

STOP (xx) PLAY(B) PAUSE/STEP (XX) VSM XTS pro

Supplies more natural and realistic sound. Supplies great sound effect.

SLEEP

Sets the System to turn off automatically at a specified time.

MUTE VOLUME (-/+)

Adjusts speaker volume.

RDS

Views the various displays of the RDS options.

RESOL.

Changes the resolution depending on your TV.

Controls the TV. (LG TV only) (See page16)

POWER

TUNER

Selects the System’s tuner (FM and AM

bands).

AUX

Selects input source.

USB

Plays the multimedia files.

DIMMER

Changes brightness of the display

window on the front panel during in

power-on status.

AUDIO

Selects an audio language (DVD) or an

audio channel (CD).

SOUND

Selects the sound mode.

REPEAT

Repeats chapter, track, title, all

REPEAT A-B

Repeats sequence.

Accesses the menu on a DVD disc.

ZOOM

SETUP

Accesses or removes setup menu.

DISPLAY

Accesses On-Screen display.

RETURN

Removes the setup menu.

b/B/v/V (left/right/up/down)

Selects an option in the menu.

ENTER

Acknowledges the menu selection.

PRESET (-/+)

Selects programme of Radio.

TUN. (-/+)

Tunes in the desired radio station.

0-9 numerical buttons

Selects a service, programme number directly or selects numbered options in

a menu.

PTY

To start a search for a specific PTY type.

HDMI

Switches the HDMI mode to HDMI

(active) and OFF (inactive).

TUNER

AUX

USB

SOUND S-TITLE CLEAR

AUDIO

REPEAT

REPEAT A-B

SCAN +

TITLE

STOP PLAY

ZOOM

PTY/HDMI

POWER

INPUT

OPEN/CLOSE

POWER

PROG./MEMO.

DIMMER

MARKER SEARCH

SKIP

DISPLAY

SETUP

ENTER

SLEEP

VOL

MUTE

RDS/RESOL.

PR VOL

DVD

SCAN +

PAUSE/STEP

RETURN

Installation and Setup

Make one of the following connections, depending on the capabilities of your existing equipment.

Tips:



Depending on your TV and other equipment you wish to connect, there are various ways you could connect the

DVD/CD Receiver

. Use one of the

connections described below.



Please refer to the manuals of your TV, VCR, Stereo System or other devices as necessary to make the best connections.

Caution:



Make sure the DVD/CD Receiver is connected directly to the TV. Select the correct AV input on your TV.



Do not connect your

DVD/CD Receiver

to TV via your VCR. The DVD image could be distorted by the copy protection system.

Video connection

Connect the MONITOR OUT jack from the DVD/CD Receiver to the VIDEO IN jack on the TV using the video cable (V).

Component Video connection

Connect the COMPONENT VIDEO OUT jacks from the DVD/CD Receiver to the corresponding jacks on the TV using an Y P

B PR cable (C).

SCART connection

Connect the EURO AV OUTPUT (TO TV) socket on the DVD/CD Receiver to the corresponding jacks on the TV using the scart cable (T).



If your television is a high-definition or “digital ready” television, you may take advantage of the DVD/CD Receiver

’s progressive scan output for the

highest video resolution.



If your TV does not accept your resolution setting, abnormal picture appears on the screen. Please read owner’s manual for TV then set the resolution that your TV can accept.

Notes:



The HDMI mode must be set to OFF for VIDEO OUT and Component video connections.



A picture via scart input is not supported.

Caution

VIDEO OUT SELECTOR switch

In power-off state, select either COMPONENT VIDEO OUT (PROGRESSIVE SCAN) or SCART signal of EURO AV TO TV terminal depending on how to connect the unit to the TV.

TV Connection

HDMI OUT

Installation and Setup

Rear of DVD/CD Receiver

Rear of TV

VTC

INPUT

MONITOR

L - AUX - R

COMPONENT VIDEO (PROGRESSIVE SCAN)

OUT PUT

VIDEO

COMPONENT VIDEO /

INPUT

PROGRESSIVE SCAN INPUT

SCART INPUT

HDMI OUT

Optional Equipment

Connection

USB connection (U)

Connect the USB port of USB Memory (or MP3 player, etc.) to the USB port on the front of the unit.

Removing the USB Device from the unit

1. Choose a different function mode or press STOP (x) twice in a row.

2. Remove the USB device from the unit.

Notes:



Don’t extract the USB device while operating.



Music files (MP3/WMA), image files (JPEG) and video files can be played.



This unit can not use a USB HUB.



Recommended Memory Cards.

Compact Flash Card (CFC), Micro Drive (MD), Smart Media Card (SMC), Memory Stick (MS), Secure Digital Card (SD), Multi Media Card (MMC), Memory Stick Pro (MS-Pro)

- Compatible with : FAT16, FAT32

- Only use the memory cards recommended.



Devices which require additional program installation when you have connected the unit to a computer are not supported.



In case of a USB HDD, make sure to connect an auxiliary power cord to the USB HDD for proper operation. Up to four primary partitions of a drive are supported. If there is an extension partition, it will not be supported.



If the drive of USB device is two or more, a drive folder is displayed on the screen. If you want to move to the initial menu after you select a folder, press RETURN.



Digital cameras and mobile phones are not supported.

AUX IN connection (A)

Connect a Output of auxiliary device to the AUX AUDIO Input (L/R) Connector.

OPTICAL IN connection (O)

Connect an optical output of DVD Player (or Digital Device etc) to the OPTICAL IN connector.

AUDIO IN connection (D)

Connect a output of portable device (MP3 or PMP etc) to the AUDIO input connector.

Antenna Connection

Connect the supplied FM/AM antenna for listening to the radio.



Connect the AM Loop antenna to the AM antenna connector.



Connect the FM Wire antenna to the FM antenna connector.

Notes:



To prevent noise pickup, keep the AM Loop antenna away from the DVD/CD Receiver and other components.



Be sure to fully extend the FM wire antenna.



After connecting the FM Wire antenna, keep it as horizontal as possible.

VIDEO

OUT IN

AUDIO (L)

AUDIO (R)

HDMI OUTHDMI OUT

OUT PUT

INPUT

L - AUX - R

MONITOR

Y COMPONENT VIDEO (PROGRESSIVE SCAN)

OPTICAL

OUT

HDMI OUT

Rear of DVD/CD Receiver

Portable device

To AUDIO OUT

To AUDIO IN

AM Loop Antenna (supplied)

FM Wire Antenna (supplied)

Auxiliary device

DVD Player (or Digital Device, etc)

USB Memory, MP3 Player (or Memory Card Reader, etc.)

To AUDIO OUT (L/R)

To AV IN AUDIO (L/R)

INPUT

MONITOR

L - AUX - R

Y COMPONENT VIDEO (PROGRESSIVE SCAN)

OUT PUT

HDMI OUT

Installation and Setup

Assembling the speaker stand to the speaker

Before connecting the speakers, assemble the speaker stand to the speaker as illustrated.

Notes:



Do not catch the speaker cord between the speaker and the post



Do not drop the speaker when mounting.

Speaker System Connection

Connect the speakers using the supplied speaker cables.

To obtain the best possible surround sound, adjust the speaker parameters (volume, distance, etc.).

Notes:



Be sure to match the speaker cable to the appropriate terminal on the components: + to + and – to –. If the cables are reversed, the sound will be distorted and will lack base.



If you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive output on the speakers.

Base

Hole

Post

1. Fix the post to the base by rotating the post. And Draw the speaker cord through the hole on the base.

2. Draw the speaker cord through the hole on the speaker. .

3. Fix the speaker to the stand by rotating the speaker. Connect the speaker cord to the appropriate terminals on the speaker.

Front speaker

(Right)

Front speaker

(Left)

Rear

speaker

(Left)

Subwoofer

Center

speaker

Rear

speaker

(Right)

+ 19 hidden pages