HR902TA-SW1/SW0_BCHESLK_ENG_1097
Wireless HDD/DVD
Recorder Receiver System
OWNER’S MANUAL
MODEL: HR902TAW/ HR952TAW
(Main Unit: HR902TAW-SW1/ HR952TAW-SW0 Speakers: SH92TA-S, SH92TA-C, SH92TA-AW,
W92-R, W92-T)
USB
Before connecting, operating or adjusting this product, please read this instruction booklet carefully and completely.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
CAUTION: THESE SERVICING INSTRUCTIONS ARE FOR USE BY QUALIFIED SERVICE PERSONNEL ONLY. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT PERFORM ANY SERVICING OTHER THAN THAT CONTAINED IN THE OPERATING INSTRUCTIONS UNLESS YOU ARE QUALIFIED TO DO SO.
Caution: The apparatus should not be exposed to water (dripping or splashing) and no objects filled with liquids, such as vases, should be placed on the apparatus.
CAUTION:
CLASS 3B VISIBLE AND INVISIBLE LASER
RADIATION WHEN OPEN AND INTERLOCKS
DEFEATED AVOID EXPOSURE TO THE BEAM.
CAUTION: This product employs a Laser
System.
To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference. Should the unit require maintenance, contact an authorized service center.
Use of controls, adjustments, or the performance of procedures other than those specified herein may result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try to open the enclosure. Visible laser radiation when open. DO NOT STARE INTO BEAM.
WARNING: Do not install this equipment in a confined space such as a bookcase or similar unit.
For Wireless product
European Union Notice
Products bearing the CE marking comply with the R&TTE Directive (1999/5/EC), EMC Directive (89/336/EEC), and the Low Voltage Directive (2006/95/EC) issued by the Commission of the European Community.
Compliance with these directives implies conformity to the following European Norms (in parentheses are the equivalent international standards and regulations):
•EN 55022 (CISPR 22)_Electromagnetic Interference
•EN 55024 (IEC61000-4-2,3,4,5,6,8,11)_ Electromagnetic Immunity
•EN 60065 (IEC 60065)_Product Safety
•EN 300 328_Technical requirements for radio equipment
•EN 301 489-1 and EN 301 489-17_General EMC requirements for radio equipment.
2
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon a dedicated circuit;
That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner's manual to be certain.
Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer.
Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.
SERIAL NUMBER:
You can find the serial number on the back of the unit. This number is unique to this unit and not available to others. You should record requested information here and retain this guide as a permanent record of your purchase.
Model No. ______________________________
Serial No. ______________________________
Disposal of your old appliance
1.When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.
2.All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.
3.The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.
4.For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.
Manufactured under license from Dolby Laboratories. “Dolby”, “Pro Logic”, and the double-D symbol are trademarks of Dolby Laboratories.
“DTS” and “DTS Digital Surround” are registered trademarks of Digital Theater Systems, Inc.
Contents |
|
|
Introduction . . . |
. . . . . . . . . . . . . . . . . . . . . . . . |
. .4-9 |
About the |
Symbol Display . . . . . . . . . . . |
. . . .4 |
Symbol Used in this Manual . . . . . . . . . . . . . |
. . .4 |
|
Notes on Discs . . . . . . . . . . . . . . . . . . . . . . . |
. . .4 |
|
Recordable and Playable Discs . . . . . . . . . . |
. . .5 |
|
Playable Discs . . . . . . . . . . . . . . . . . . . . . . . |
. . .6 |
|
Regional Code . . . . . . . . . . . . . . . . . . . . . . . |
. . .6 |
|
Availability of copying feature . . . . . . . . . . . . |
. . .6 |
|
About the internal hard disk drive . . . . . . . . . |
. . .7 |
|
Playing media files using the USB feature . . . |
. . .7 |
|
Front Panel . . |
. . . . . . . . . . . . . . . . . . . . . . . . |
. . .8 |
Remote Control . . . . . . . . . . . . . . . . . . . . . . |
. . .9 |
|
Remote Control Operation . . . . . . . . . . . . . . |
. . .9 |
|
Hookup and Settings . . . . . . . . . . . . . . . . . . . |
10-28 |
|
Rear Panel . . |
. . . . . . . . . . . . . . . . . . . . . . . . |
. .10 |
Connecting to the Aerial . . . . . . . . . . . . . . . . |
. .10 |
|
Connections to Your TV . . . . . . . . . . . . . . . . |
. .11 |
|
HDMI connection . . . . . . . . . . . . . . . . . . . . . |
. .12 |
|
Accessory Audio/Video (A/V) Connections . . |
13-14 |
|
Radio Antenna Connections . . . . . . . . . . . . . |
. .14 |
|
Assembling and Connecting to the Speakers |
. .15 |
|
Speaker System Connections . . . . . . . . . . . . |
. .16 |
|
Setup the Wireless System . . . . . . . . . . . . . . |
. .17 |
|
Setting an ID of Wireless TX . . . . . . . . . . . . . |
. .18 |
|
Speaker Positioning . . . . . . . . . . . . . . . . . . . |
. .19 |
|
XTS/XTS pro |
. . . . . . . . . . . . . . . . . . . . . . . . |
. .20 |
Sound Mode . |
. . . . . . . . . . . . . . . . . . . . . . . . |
. .20 |
Controlling Your TV with the Supplied Remote |
||
Control . . . . . |
. . . . . . . . . . . . . . . . . . . . . . . . |
. .20 |
Using the Home Menu . . . . . . . . . . . . . . . . . |
. .21 |
|
Initial Settings . . . . . . . . . . . . . . . . . . . . . . . . |
. .21 |
|
General Settings . . . . . . . . . . . . . . . . . . . . . |
21-23 |
|
Auto Programming . . . . . . . . . . . . . . . . . |
. .21 |
|
Program Edit . . . . . . . . . . . . . . . . . . . . . . |
. .22 |
|
AV1 Decoder . . . . . . . . . . . . . . . . . . . . . . |
. .22 |
|
Auto Clock Set . . . . . . . . . . . . . . . . . . . . |
. .23 |
|
Manual Clock Set . . . . . . . . . . . . . . . . . . |
. .23 |
|
TV Aspect |
. . . . . . . . . . . . . . . . . . . . . . . . |
. .23 |
Display Mode . . . . . . . . . . . . . . . . . . . . . |
. .23 |
|
AV2 Connection . . . . . . . . . . . . . . . . . . . |
. .23 |
|
Video Output Format . . . . . . . . . . . . . . . . |
. .23 |
|
Power Save Mode . . . . . . . . . . . . . . . . . . |
. .23 |
|
Initialization . . . . . . . . . . . . . . . . . . . . . . . |
. .23 |
|
Language Settings . . . . . . . . . . . . . . . . . . . . |
. .24 |
|
Audio Settings . . . . . . . . . . . . . . . . . . . . . . . |
. .24 |
|
DRC (Dynamic Range Control) . . . . . . . . |
. .24 |
|
5.1 Speaker Setup . . . . . . . . . . . . . . . . . |
. .24 |
|
Lock (Parental Control) Settings . . . . . . . . . . |
. .25 |
|
Set Password / Rating / Area Code . . . . . |
. .25 |
|
DivX Registration Code . . . . . . . . . . . . . |
. .25 |
|
Recording Settings . . . . . . . . . . . . . . . . . . . . |
. .26 |
|
Record Mode Set . . . . . . . . . . . . . . . . . . |
. .26 |
|
Record Aspect . . . . . . . . . . . . . . . . . . . . . |
. .26 |
|
DV Recording Audio . . . . . . . . . . . . . . . . |
. .26 |
|
Auto Chapter . . . . . . . . . . . . . . . . . . . . . . |
. .26 |
|
Timeshift . |
. . . . . . . . . . . . . . . . . . . . . . . . |
. .26 |
Disc Settings |
. . . . . . . . . . . . . . . . . . . . . . . . |
26-27 |
Disc Format . . . . . . . . . . . . . . . . . . . . . . |
. .26 |
|
Finalize / Disc Label . . . . . . . . . . . . . . . . |
. .27 |
|
Disc Protect . . . . . . . . . . . . . . . . . . . . . . |
. .27 |
|
General Explanation of On-Screen Display . . |
. .28 |
Playback . . . . . . . . . . . . . . . . . . . . . . . . . . . . .29-39
General Playback Features . . . . . . . . . . . . .29-32 Playing a DivX Movie File . . . . . . . . . . . . . . . . .33 Playing an Audio CD or MP3/WMA file . . . . . . .34 Program Playback with Audio CD and
MP3/WMA file . . . . . . . . . . . . . . . . . . . . . . . . . .35 Viewing a JPEG File . . . . . . . . . . . . . . . . . .36-37 Editing a MP3/WMA, JPEG, DivX file . . . . . .38-39
Recording . . . . . . . . . . . . . . . . . . . . . . . . . . . .40-47
About DVD recording . . . . . . . . . . . . . . . . . . . .40 About HDD recording . . . . . . . . . . . . . . . . . . . .40 Timeshift . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .41 Basic Recording from a TV . . . . . . . . . . . . . . . .42 Instant Timer Recording . . . . . . . . . . . . . . . . . .42 Timer Recording . . . . . . . . . . . . . . . . . . . . . . . .43 Timer Recording with ShowView® System . . . .44 Checking Timer Recording Details . . . . . . . . . .45 Recording from an External Input . . . . . . . . . . .45 Recording from DV Input . . . . . . . . . . . . . . . . .46 Simultaneous recording and playback . . . . . . . .47 Ripping CDs (for audio CDs) . . . . . . . . . . . . . . .47 To find your ripped tracks . . . . . . . . . . . . . . . . .47
Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . |
48-54 |
Title List and Chapter List Menu Overview . . . .48 |
|
HDD, VR Mode: Original and Playlist Editing |
. . .49 |
Adding Chapter Markers . . . . . . . . . . . . . . . |
. .49 |
Changing Title Thumbnails . . . . . . . . . . . . . . |
. .49 |
Making a New Playlist . . . . . . . . . . . . . . . . . . |
. .50 |
Adding Additional Title/Chapters to the Playlist .50 |
|
Deleting an Original or Playlist Title/Chapter |
. . .51 |
Deleting a Part . . . . . . . . . . . . . . . . . . . . . . . |
. .51 |
Naming a Title . . . . . . . . . . . . . . . . . . . . . . . |
. .52 |
Divide One Titles Into Two . . . . . . . . . . . . . . |
. .53 |
Combining Two Chapters Into One . . . . . . . |
. . .53 |
Moving a Playlist Chapter . . . . . . . . . . . . . . . |
. .54 |
Hide a Chapter . . . . . . . . . . . . . . . . . . . . . . . |
. .54 |
Protect a Title . . . . . . . . . . . . . . . . . . . . . . . . |
. .54 |
Dubbing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .55-56
Before Dubbing . . . . . . . . . . . . . . . . . . . . . . . . .55 Dubbing from HDD to DISC . . . . . . . . . . . . . . .56 Dubbing from DISC to HDD . . . . . . . . . . . . . . .56
Reference . . . . . . . . . . . . . . . . . . . . . . . . . . . .57-64
Additional Information . . . . . . . . . . . . . . . . . . . .57 Overwriting Recording . . . . . . . . . . . . . . . . .57 Viewing Title List menu displayed on other DVD Recorders or Players . . . . . . . . . . . . .57 Playing Your Recordings on Other DVD Players (Finalizing a Disc) . . . . . . . . . . . . . .57
Language Codes . . . . . . . . . . . . . . . . . . . . . . .58 Area Codes . . . . . . . . . . . . . . . . . . . . . . . . . . .58 Presetting the Radio Stations . . . . . . . . . . . . . .59 Listening to the Radio . . . . . . . . . . . . . . . . . . .59 RDS Operation . . . . . . . . . . . . . . . . . . . . . . . .60 Programme Search (PTY) . . . . . . . . . . . . . . . .60 Troubleshooting . . . . . . . . . . . . . . . . . . . . . .61-62 Specifications . . . . . . . . . . . . . . . . . . . . . . .63-64
<![endif]>Introduction
3
Introduction
To ensure proper use of this product, please read this owner’s manual carefully and retain for future reference.
This manual provides information on the operation and maintenance of your recorder. Should the unit require service, contact an authorized service location.
About the Symbol Display
“ ” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that specific media.
Symbol Used in this Manual
Note:
Indicates special notes and operating features.
Tip:
Indicates tips and hints for making the task easier.
A section whose title has one of the following symbols are applicable only to the disc represented by the symbol.
HDD recorded on the HDD
All DVD discs listed below.
-RAM disc
DVD-RW with VR recording mode
DVD-RW with Video recording mode
DVD+RW disc
DVD-R disc
DVD+R (DL) disc
DVD-Video disc
Audio CDs
DivX files
MP3 files
WMA files
Notes on Discs
Handling Discs
Do not touch the playback side of the disc. Hold the disc by the edges so that fingerprints do not get on the surface. Never stick paper or tape on the disc.
Storing Discs
After playing, store the disc in its case. Do not expose the disc to direct sunlight or sources of heat and never leave it in a parked car exposed to direct sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor picture quality and sound distortion. Before playing, clean the disc with a clean cloth. Wipe the disc from the center out.
Do not use strong solvents such as alcohol, benzine, thinner, commercially available cleaners, or anti-static spray intended for older vinyl records.
Moisture Condensation
Never operate this product immediately after moving it from a cold location to a warm location. Leave it for two or three hours without operating it. If you use this product in such a situation, it may damage discs and internal parts.
What is SIMPLINK?
Some functions of this unit are controlled by TV’s remote control when this unit and LG TV with SIMPLINK are connected through HDMI connection.
•Controllable functions by LG TV’s remote control; Play, Pause, Scan, Skip, Stop, Power Off, etc.
•Refer to the TV owner’s manual for the details of SIMPLINK function.
•LG TV with SIMPLINK function has the logo as shown above.
4
Recordable and Playable Discs
DVD-RW (Digital Video Disc - ReWritable):
DVD-RW discs can be formatted for VR mode recording or Video mode recording.
These Discs can be recorded on repeatedly. Recordings can be erased, then you can record again on the same Disc.
[VR mode]
Recordings can be extensively edited
Playable only on VR mode compatible players (after finalization) [Video mode]
Playable on regular DVD players (after finalization)
Limited editing features
DVD-R (Digital Video Disc - Recordable)
These Discs can be recorded only once. After you finalize a DVD-R, you cannot record on it or edit it.
DVD-R discs can be only formatted to Video mode.
Playable on regular DVD players (after finalization)
Limited editing features
DVD-RAM (DVD - Random Access Memory)
DVD-RAM discs can be formatted for VR mode recording.
These Discs can be recorded on repeatedly. Recordings can be erased, then you can record again on the same Disc.
Playable on DVD-RAM compatible players.
Recordings can be extensively edited.
Only DVD-RAM standard Version 2.0, 2.1 and 2.2 discs can be used in this unit.
You cannot use the cartridge-type DVD-RAM disc in this unit.
DVD+RW (Digital Video Disc + ReWritable)
These Discs can be recorded on repeatedly. Recordings can be erased, then you can record again on the same Disc.
Playable on DVD+RW compatible players (automatically finalization)
The edited contents are playable on DVD+RW compatible players only after finalization
Recordings can be edited the title/chapter
DVD+R (Digital Video Disc + Recordable)
These Discs can be recorded only once. After you finalize a DVD+R, you cannot record on it or edit it any more.
Playable on DVD+R compatible players (after finalization)
Any edited contents are not be compatible on DVD+R compatible players. (Hide, chapter combine, added chapter mark, etc.)
Limited title/chapter editing features.
DVD+R DL (Digital Video Disc + Recordable; Double Layer)
These Discs can be recorded only once. After you finalize a DVD+R DL, you cannot record on it or edit it any more.
Storage space is nearly doubled with double layer DVD+R media, allowing consumers to record up to 8.5GB of video on a single DVD+R disc.
Playable on DVD+R DL compatible players (after finalization)
Any edited contents are not be compatible on DVD+R DL compatible players. (Hide, chapter combine, added chapter mark, etc.)
Limited title/chapter editing features.
Recommended recordable DVD discs
DVD-R |
DVD+R |
DVD-RW |
DVD+RW |
DVD+R(DL) |
DVD-RAM |
Mitsubishi (8x, 16x) |
Mitsubishi (8x, 16x) |
Mitsubishi (4x) |
Mitsubishi (4x) |
Mitsubishi (2.4x) |
Fujifilm (2x) |
That’s (8x, 16x) |
Ricoh (8x, 16x) |
Verbatim (4x) |
SONY (2.4x) |
Maxell (2.4x) |
Mitsubishi (3x) |
SONY (16x) |
SONY (16x) |
JVC (4x) |
Verbatim (2.4x) |
- |
- |
|
|
|
|
|
|
- |
- |
Victor (4x) |
Ricoh (2.4x, 4x) |
- |
- |
|
|
|
|
|
|
- |
- |
Maxell (4x) |
- |
- |
- |
|
|
|
|
|
|
Note:
If a DVD-RW/DVD+RW discs is recorded using a personal computer or other HDD/DVD Recorder Receiver, you cannot format the disc using this recorder. So if you want to use the disc on this recorder, you must format the disc using the original recorder.
<![endif]>Introduction
5
Playable Discs
DVD (8 cm / 12 cm disc)
Discs such as movies that can be purchased or rented
Audio CD (8 cm / 12 cm disc)
Music CDs or CD-Rs/CD-RWs in music CD format that can be purchased
CD-R/CD-RW (8 cm / 12 cm disc)
CD-R/CD-RW discs that contain audio titles, DivX, MP3, WMA, or JPEG files.
Notes:
–Depending on the conditions of the recording equipment or the CD-R/RW (or DVD±R/RW) disc itself, some CD-R/RW (or DVD±R/RW) discs cannot be played on the unit.
–Do not attach any seal or label to either side (the labeled side or the recorded side) of a disc.
–Do not use irregularly shaped CDs (e.g., heart-shaped or octagonal). Doing so may result in malfunctions.
–Depending on the recording software & the finalization, some recorded discs (CD-R/RW or DVD±R/RW) may not be playable.
–DVD-R/RW, DVD+R/RW and CD-R/RW discs recorded using a personal computer or a DVD or CD Recorder may not play if the disc is damaged or dirty, or if there is dirt or condensation on the Recorder’s lens.
–If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. (Check with the software publisher for more detailed information.)
–This recorder requires discs and recordings to meet certain technical standards in order to achieve optimal playback quality. Pre-recorded DVDs are automatically set to these standards. There are many different types of recordable disc formats (including CD-R containing MP3 or WMA files) and these require certain preexisting conditions (see above) to ensure compatible playback.
–Customers should note that permission is required in order to download MP3 / WMA files and music from the Internet. Our company has no right to grant such permission. Permission should always be sought from the copyright owner.
Regional Code
This unit has a regional code printed on the rear of the unit. This unit can play only DVD discs labeled same as the rear of the unit or “ALL”.
Notes on Regional Codes
Most DVD discs have a globe with one or more numbers in it clearly visible on the cover. This number must match your unit’s regional code or the disc cannot play.
If you try to play a DVD with a different regional code from the unit, the message “Incorrect region code. Can’t play back” appears on the TV screen.
Availability of copying feature
From |
To |
MP3/WMA |
JPEG |
DivX |
Audio CD |
Title*1 |
HDD |
DISC |
No |
No |
No |
No |
Yes |
HDD |
USB device |
No |
No |
No |
No |
No |
DISC |
HDD |
Yes |
Yes |
Yes |
No*2 |
Yes |
DISC |
USB device |
No |
No |
No |
No |
No |
USB device |
DISC |
No |
No |
No |
No |
No |
USB device |
HDD |
Yes |
Yes |
Yes |
No |
No |
*1 The title is recorded from this unit.
*2 You can rip Audio CD tracks to the hard disk.
6
About the internal hard disk drive
The internal hard disk drive (HDD) is a fragile piece of equipment. Please use the recorder following the guidelines below to protect against possible HDD failure.
We recommend that you back up your important recordings onto DVD discs in order to protect against accidental loss.
Do not move the recorder while it is on.
Install and use the recorder on a stable, level surface.
Do not block the rear vent/cooling fan.
Do not use the recorder in excessively hot or humid places, or in places that may be subject to sudden changes in temperature. Sudden changes in temperature can cause condensation to form inside the recorder. This can be a cause of HDD failure.
While the recorder is switched on, do not unplug from the wall socket or switch the electricity off from the breaker switch.
Do not move the recorder immediately after switching it off. If you need to move the recorder, please follow the steps below:
1.After the message POWER OFF is shown in the display, wait at least two minutes.
2.Unplug from the wall socket.
3.Move the recorder.
If there’s a power failure while the recorder is on there is a chance that some data on the HDD will be lost.
The HDD is very delicate. If used improperly or in an unsuitable environment, it is possible that the HDD will fail after a few years of use. Signs of problems include playback unexpectedly freezing and noticeable block noise (mosaic) in the picture. However, sometimes there will be no warning signs of HDD failure.
If the HDD fails, no playback of recorded material will be possible. In this case it will be necessary to replace the HDD unit.
Playing media files using the USB feature
You can enjoy the media files such as pictures (JPEG), movies (DivX) and tunes (MP3/WMA) saved in an MP3 player or USB memory by connecting the storage device to the USB port of this unit.
1.Connect the USB device to the USB port of the unit.
2.Press HOME on the remote control.
3.Select [MUSIC], [PHOTO] or [MOVIE] option. Details for the options are on page 21.
Compatible Devices
1.Devices which require additional program installation when you have connected it to a computer, are not supported.
2.MP3 Player: Flash type MP3 player.
•The MP3 player requiring installation of a driver is not supported.
3.USB Flash Drive: Devices that support USB2.0 or USB1.1.
Notes:
Do not extract the USB device in operating (play, copy, move, etc.).
A back up demands to prevent a data damage.
If you use a USB extension cable or USB hub, the USB device might not be recognized.
This unit can support USB 2.0 or USB 1.1.
A device using NTFS file system is not supported. (Only FAT (16/32) file system is supported.)
The USB function of this unit does not support all USB devices.
Digital camera and mobile phone are not supported.
This unit is not supported when the total number of files is 1000 or more.
DivX playback on USB may not be perfect for high bit rate content.
When resetting this unit, remove the USB device from the USB port of this unit (see page 62.)
<![endif]>Introduction
7
Front Panel
|
a |
b |
|
|||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
aPOWER
Switches the HDD/DVD Recorder Receiver ON or OFF.
bDisc Tray
Insert a disc here.
cDisplay window
Shows the current status of the recorder. REC: The recorder is recording.
HDD: The recorder is HDD mode. DVD: The recorder is DVD mode.
DVD b B HDD : The recorder is dubbing. MUTE: The speaker sound is muted.
,
D : Indicates encoding format of the current disc.
PLII : Indicates sound mode is DOLBY PRO LOGIC or DOLBY PRO LOGIC II.
: Indicates when the recorder is in timer recording or a timer recording is programmed.
: Indicates clock, total playing time, elapsed time, title number, radio frequency, volume, Surround, chapter/track number, channel, etc.
d Remote Sensor
Point the recorder remote control here.
e OPEN/CLOSE (Z)
Opens or closes the disc tray.
c |
|
|
d e f g h i j k |
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
l m
fx (STOP)
Stops playback or recording.
gN / X (PLAY / PAUSE)
Starts playback.
Pause playback or recording temporarily, press again to exit pause mode.
hz (REC)
Starts recording. Press repeatedly to set the recording time.
iHDD/DVD
Set the recorder’s mode to HDD or DVD.
jADJUST
-Scans up or down through memorized channels.
-Selects menu options.
kVOL. (+/-)
Adjust speaker volume.
lUSB
Connect to a USB port of multimedia (USB memory etc.).
mDV IN
Connect the DV output of a digital camcorder.
Touch Pad Operation |
Precautions in using the touch pad |
|
The LEDs on the touch pad lights only when the |
||
The buttons from e to k are touch pad type button |
||
power of the unit is on. |
||
that is operated with brief touch. |
Use the touch pad with clean and dry hands. |
|
When you operate the button on the touch pad, you |
Do not press the button on the touch pad with too |
|
should follow the directions as below. |
much force. |
|
1. Touch the any button on the touch pad. |
Do not touch the button on the touch pad with any |
|
The LEDs on the touch pad light up. |
conductive material such as metalic object. |
|
2. Touch the button you want to operate. |
It may cause a malfunction. |
|
|
||
The LEDs on the touch pad will be off in 10 |
|
|
seconds after the operation. |
|
|
|
|
8
Remote Control |
b |
|
|
||
|
FM/AM: Select FM or AM band as the |
|
|
listening choice. (FM and AM bands). |
|
a |
REPEAT: Repeat chapter, track, title or |
|
all. |
||
|
||
|
A-B: Repeats sequence between two |
|
|
points (A and B) |
|
b |
CHP ADD: Inserts a chapter marker |
|
when playing/ recording. |
||
|
REC: Starts recording. Press |
|
|
repeatedly to set the recording time. |
|
c |
TIMER REC: Displays Timer Record |
|
menu. |
||
|
REC MODE: Selects the recording |
|
|
mode: XP, SP, LP or EP. |
|
|
INSTANT SKIP: Skips 15 seconds |
|
d |
forward during playback. |
|
AUDIO/MO.ST.: Selects an audio |
||
|
language. Selects STEREO or MONO. |
|
|
SUBTITLE: Selects a subtitle |
|
|
language. |
|
|
THUMBNAIL: Selects a thumbnail |
|
|
picture |
|
|
TIMESHIFT: Activates pause live |
|
|
TV/playback (timeshift) for a live TV |
|
e |
program. |
|
c |
||
|
||
|
SCAN (-/+) (m/M):Search |
|
|
backward or forward. |
|
|
SKIP (-/+) (. / >): Go to next |
|
f |
chapter or track. Returns to beginning |
|
of current chapter or track or go to |
||
|
previous chapter or track. |
|
|
PROGRAM:Accesses or removes |
|
|
program menu. |
|
|
STOP (x): Stops playback or |
|
|
recording. |
|
a |
PLAY (B): Starts playback. |
|
PAUSE/STEP (X): Pause playback or |
||
AV: Changes the input to use for |
||
recording temporarily. |
||
recording.(Tuner, AV1, AV2, AV3, |
||
|
||
OPT(AV3 Opt) or DV). |
d |
|
PIP: Selects PIP function on or off. |
MENU/LIST: Accesses menu on a |
|
POWER: Turns HDD/DVD Recorder |
DVD disc, Switches between Title List- |
|
Receiver ON and OFF. |
Original and Title List-Playlist menu. |
|
OPEN/CLOSE: Opens and closes the |
TITLE: Displays the disc’s Title menu, |
|
disc tray |
if available. |
|
TV/DVD: To view channels selected by |
HOME: Accesses or removes the |
|
the recorder tuner or by the TV tuner. |
HOME menu. |
DISPLAY: Accesses On-Screen Display. Displays information while viewing a TV program.
RETURN (O): Removes the menu. PR (+/-): Select programme of TV or Radio.
b / B / v / V (left/right/up/down):
Selects menu options.
MEMORY/ENTER : Confirms menu selections. Stores a radio station’s frequency in the tuner’s memory. XTS Pro: To enjoy more natural and realistic sound.
SOUND: Selects sound mode. MARKER: Marks any point during playback
SEARCH: Displays Marker Search menu.
VOL (+/-): To adjust speaker volume.
e
0-9 numerical buttons: Selects numbered options in a menu. CLEAR: Removes a mark on the Marker Search menu.
MUTE: Turns the sound on and off temporarily.
f
SHOWVIEW: To display the program menu for SHOWVIEW System programming.
RDS/RESOL.: To view the various displays of the RDS options. Sets the output resolution for HDMI.
PTY: To start a search for a specific PTY type.
TV Control Buttons: See page 20.
Remote Control Operation
Point the Remote Control at the remote sensor and press the buttons.
Remote Control Battery Installation
Remove the battery cover on the rear of the Remote Control, and insert two (size AA) batteries with and
matched correctly.
Caution
Do not mix old and new batteries. Never mix different types of batteries (standard, alkaline, etc.).
<![endif]>Introduction
9
Hookup and Settings
Rear Panel
a b c |
|
d |
e |
f |
g |
|
|||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
h i j k l
a IN (FROM ANT.)
Connect the aerial to this terminal.
b AV OUT (VIDEO / AUDIO OUT (Left/Right))
Connect to a TV with video/audio inputs.
c AV IN 3 (VIDEO IN/AUDIO IN (Left/Right))
Connect the audio/video output of an external source (Audio system, TV/ Monitor, VCR, Camcorder, etc.).
d EURO AV 2 DECODER
Connect the audio/video output of an external source (Pay-TV decoder, Set Top Box, VCR, etc.).
e HDMI OUTPUT (Type A)
HDMI output providing a high quality interface for digital audio and video.
f Cooling fan
g AC Power Cord
Plug into the power source.
h OUT (TO TV)
Passes the signal from the AERIAL to your TV/monitor
i OPTICAL IN Connector
Connect an optical output of Digital Device.
j COMPONENT/PROGRESSIVE SCAN VIDEO OUT (Y Pb Pr)
Connect to a TV with Y Pb Pr inputs.
kSYSTEM
Connect the SPEAKER SYSTEM at the Active Speaker.
lEURO AV 1 AUDIO/VIDEO
Connect to a TV with SCART jack.
Connecting to the Aerial
Remove the aerial cable plug from your TV set and insert it into the IN (FROM ANT.) socket at the back of the recorder. Plug one end of the aerial cable into the TV socket on the recorder and the other end into the aerial input socket on your TV set.
RF coaxial connection
Connect the OUT (TO TV) jack on the HDD/DVD Recorder Receiver to the aerial input jack on the TV using the 75-ohm Coaxial Cable (R). The OUT (TO TV) jack passes the signal through from the IN (FROM ANT.) jack.
Rear of TV
Aerial |
|
|
|
SCART INPUT |
|
ANTENNA |
AUDIO INPUT |
VIDEO |
INPUT |
|
INPUT |
|
L R |
|
R (Not supplied)
Rear of the HDD/DVD Recorder Receiver
10
Connections to Your TV
Make one of the following connections, depending on the capabilities of your existing equipment.
When using the COMPONENT/PROGRESSIVE SCAN VIDEO OUT jacks, set the Video output format option in the setup menu to YPbPr. When using the SCART jack, set the Video output format option in the setup menu to RGB.
Tips
Depending on your TV and other equipment you wish to connect, there are various ways you could connect the recorder. Use only one of the connections described below.
Please refer to the manuals of your TV, VCR, Stereo System or other devices as necessary to make the best connections.
Caution
Make sure the recorder is connected directly to the TV. Tune the TV to the correct video input channel.
Do not connect the recorder’s AUDIO OUT jack to the phono in jack (record deck) of your audio system.
Do not connect your recorder via your VCR. The DVD image could be distorted by the copy protection system.
Rear of TV
|
|
|
|
|
SCART INPUT |
VIDEO |
AUDIO INPUT |
COMPONENT VIDEO INPUT |
|||
INPUT |
|||||
|
L |
R |
Y |
Pb |
Pr |
V A C (Not supplied) T
Rear of the HDD/DVD
Recorder Receiver
O (Not supplied)
OPTICAL
OUT
DVD Player (or Digital
Device, etc)
Video connection
Connect the VIDEO OUT jack on the recorder to the video in jack on the TV using the video cable (V).
Audio (Left/Right) Connection
Connect the left and right AUDIO OUT jacks of the recorder to the audio left and right IN jacks on the TV using the audio cables (A). Do not connect the recorder’s AUDIO OUT jack to the phono in jack (record deck) of your audio system.
Component Video connection
Connect the COMPONENT / PROGRESSIVE SCAN VIDEO OUT jacks on the recorder to the corresponding input jacks on the TV using an Y Pb Pr cable (C).
If your television is a high-definition or “digital ready” television, you may take advantage of the recorder’s progressive scan output for the highest video resolution possible. If your TV does not accept the Progressive Scan format, the picture will appear scrambled if you try Progressive Scan on the recorder.
Set the resolution to 576p using RDS/RESOL. button for progressive signal.
Note:
Progressive scan does not work with the analog video connections (yellow VIDEO OUT jack) connection.
SCART connection
Connect the EURO AV1 AUDIO/VIDEO scart jack on the recorder to the corresponding in jacks on the TV using the scart cable (T).
Optical Digital Connection
Connect an optical output of DVD Player (or Digital Device etc) to the OPTICAL IN connector on the recorder using the optical cable (O).
Note:
When the Optical jack is connected, audio will output from speakers of the main unit amplifier only but the audio output is not available via the HDMI and AV jacks.
<![endif]>Settings
<![if ! IE]><![endif]>Hookup and
11
HDMI connection
If you have a HDMI TV or monitor, you can connect it to this recorder using a HDMI cable.
1.Connect the HDMI OUTPUT jack on the recorder to the HDMI jack on a HDMI compatible TV or monitor (H).
2.Set the TV’s source to HDMI (refer to TV’s Owner’s manual).
Notes:
The arrow on the cable connector body should face up for correct alignment with the connector on the recorder.
(Type A)
If there is noise or lines on the screen, please check the HDMI cable.
If you press RDS/RESOL. in RADIO mode, the resolution is not changed.
Tip :
When you use HDMI connection, you can change the resolution (576p, 720p, or 1080i) for the HDMI output using RDS/RESOL. button.
Caution
Changing the resolution when the recorder is connected with HDMI connector may result in malfunctions. To solve the problem, turn off the recorder and then turn it on again.
HDMI compatible TV
HDMI
H (Not supplied)
Rear of the HDD/DVD Recorder Receiver
About HDMI
HDMI (High Definition Multimedia Interface) supports both video and audio on a single digital connection for use with DVD Players, Set-Top Boxes, and other AV devices.
HDMI was developed to provide the technologies of HDCP (High Definition Contents Protection). HDCP is used to protect digital content transmitted and received.
HDMI has the capability to support standard, enhanced, or high-definition video plus standard to multi-channel surround-sound audio, HDMI features include uncompressed digital video, a bandwidth of up to 5 gigabytes per second, one connector (instead of several cables and connectors), and communication between the AV source and AV devices such as DTVs.
HDMI, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI licensing LLC.
Additional Information for HDMI
When you connect a HDMI or DVI compatible device make sure of the followings:
-Try switching off the HDMI/DVI device and this recorder. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this recorder.
-The connected device’s video input is set correctly for this unit.
-The connected device is compatible with 720x576p, 1280x720p, or 1920x1080i video input.
Not all HDCP-compatible DVI devices will work with this recorder.
-The picture will not be displayed properly with non-HDCP device.
-When the connected TV cannot accept the resolution you selected, you may not see normal picture on the TV screen.
12
Accessory Audio/Video (A/V)
Connections
Connecting a PAY-TV/Canal Plus Decoder
You can watch or record PAY-TV/Canal Plus programmes if you connect a decoder (not supplied) to the recorder. Disconnect the recorder’s mains lead from the mains when connecting the decoder.
To watch or record PAY-TV/Canal Plus programmes, set [AV2 Connection] option to [Decoder] (see page 23) and set the program’s [Decoder On/Off] option to [On] on the Setup menu (page 22).
Tip:
You do not need to turn on the recorder to view the signals from the connected tuner on your TV.
Note:
If you disconnect the recorder’s mains lead, you will not be able to view the signals from the connected decoder.
TV
PAY-TV/Canal Plus
Decorder
SCART AV
Rear of the HDD/DVD Recorder Receiver
Connecting to the EURO AV2 DECODER jack
Connect a VCR or similar recording device to the EURO AV2 DECODER jack of this recorder.
To watch or record the source from EURO AV2 DECODER jack, set [AV2 Connection] option to [Others] (see page 23).
TV
VCR, Cable Box, or Satellite Tuner, etc.
Rear of the HDD/DVD Recorder Receiver
Tip:
You do not need to turn on the recorder to view the signals from the connected tuner on your TV.
Notes:
Pictures containing copy protection signals that prohibit any copying cannot be recorded.
If you pass the recorder signals via the VCR, you may not receive a clear image on your TV screen. Be sure to connect your VCR to the recorder and your TV in the order shown below. To watch video tapes, watch the tapes through a second line input on your TV.
Line input 1
VCR RECORDER
TV
Line input 2
When you record to a VCR from this recorder, do not switch the input source to TV by pressing the TV/DVD button on the remote.
If you are using a B Sky B tuner, be sure to connect the tuner’s VCR SCART jack to the EURO AV2 DECODER jack.
If you disconnect the recorder’s mains lead, you will not be able to view the signals from the connected VCR or tuner.
<![endif]>Settings
<![if ! IE]><![endif]>Hookup and
13
Connecting to the AV IN 3 Jacks
Connect the input jacks (AV IN 3) on the recorder to the audio/video out jacks on your accessory component, using audio/video cables.
AUDIO
OUTPUT
R
L
VIDEO
OUTPUT
Rear of the HDD/DVD
Recorder Receiver
Connecting a Digital Camcorder
Using the front panel DV IN jack, it is possible to connect a DV digital camcorder and digitally transfer DV tapes to DVD.
Use a DV cable (not supplied) to connect the DV in/out jack of your DV camcorder to the front panel DV IN jack of this recorder.
Note:
This jack is for connection to DV digital camcorder only. It is not compatible with digital satellite tuners or D-VHS video decks.
DV Digital Camcorder
DV
IN/OUT
Front of the HDD/DVD Recorder Receiver
Radio Antenna Connections
Connect the supplied FM/AM antennas for listening to the radio.
Connect the AM loop antenna to the AM antenna connector.
Connect the FM wire antenna to the FM antenna connector.
Notes:
To prevent noise pickup, keep the AM loop antenna away from the HDD/DVD Recorder Receiver System and other components.
Be sure to fully extend the FM wire antenna.
After connecting the FM wire antenna, keep it as close to horizontal as possible.
AM |
GND |
FM |
14
Assembling and Connecting to the Speakers
1.Connect the speaker cables to the appropriate terminals on the bottom of each front and rear speakers.
2.Attach the front and rear speakers to the speaker stands by rotating the screw.
<![if ! IE]><![endif]>Settings
<![if ! IE]><![endif]>Hookup and
Note:
If you hold the top of speakers when carrying the speaker, it may cause the separation of speakers. Therefore it might be damaged.
15
Speaker System Connections
Connect the speakers to the front (right, left) or center speaker connectors of the Active Subwoofer Speaker.
Connect the power cord of the Wireless RX to the outlet, then connect the Wireless RX and the rear speaker (right, left) with the speaker cable.
Connect the DC IN connector of the Wireless TX and the Wireless TX (DC 7V OUT) connector of the Active Subwoofer Speaker with the DC power cable.
Connect the SIGNAL connector of the Wireless TX and rear (right, left) speaker connectors of the Active Subwoofer Speaker with the sound signal cable.
Set the distance between Wireless TX and Wireless RX within 10m.
Connect the SYSTEM to the SYSTEM CONNECTOR on the rear of the Active Subwoofer Speaker, using the supplied System cable.
Wireless TX
DC power cable
Black |
Red |
Sound signal cable |
|
Wireless Speaker |
Wireless Speaker |
[Rear speaker (Right)] |
[Rear speaker (Left)] |
Notes:
Optimum performance can be implemented only when the Wireless TX and the Wireless RX within distance of 2m to 10m is used since communication failure may occur if longer distance is used.
Be sure to match the speaker cable to the appropriate terminal on the components: + to + and – to –. If the cables are reversed, the sound will be distorted and will lack base.
It takes about a few seconds (and may take longer) for the Wireless TX and Wireless RX to communicate with each other.
If you use front speakers with low maximum input rating, adjust the volume carefully to avoid excessive output on the speakers.
When the unit is turned off, the Wireless RX is in standby mode (off) automatically after about 10 seconds.
If the Wireless RX is turned off, the rear speaker will not function.
16
About Ferrite Core
Be sure to attach the ferrite core to the system cable. This ferrite core can reduce noises.
How to attach the ferrite core
1.Press the stopper [a] of the ferrite core to open.
2.Wind the system cable once on the ferrite core.
3.Close the ferrite core until it clicks.
Note:
Attach the ferrite core near the unit (Refer to the fig.3
and comment.).
LED indicator of wireless TX
*LED indicator - “BLUE”
The main set is turned on, everthing is connected and transmitting.
*LED indicator - “RED”
The Wireless TX is in standby mode.
*LED indicator - “OFF (No display)” The main set is turned off.
LED indicator
Displays the operating status.
The length here is short as much as possible.
Setup the Wireless System
Note:
If there is a product with a strong electromagnetic field nearby, interference may occur.
(Ex : Micro wave oven)
Wireless TX
SIGNAL |
ID. |
DC IN |
DC IN connector
ID (ID.) button
SOUND SIGNAL connector
Wireless RX
LED indicator
Displays the operated status.
LED indicator of Wireless RX
*LED indicator - “BLUE”
The Wireless RX is receiving a signal of Wireless TX.
*LED indicator - “RED”
The Wireless RX is in standby mode.
Rear speaker connector
Power cord
<![endif]>Settings
<![if ! IE]><![endif]>Hookup and
17
Setting an ID of Wireless TX
When the unit is manufactured, the ID is already set. If an interference occurs or you use a new Wireless RX, an ID is set again.
1.Connect the SIGNAL connector of the Wireless TX and rear (right, left) speaker connectors of the Active Subwoofer Speaker with the sound signal cable.
2.Connect the DC IN connector of the Wireless TX and the Wireless TX (DC 7V OUT) connector of the Active Subwoofer Speaker with the DC power cable.
3.Disconnect power cord of Wireless RX.
4.Press the ID. button for more than about 3 seconds.
The blue LED indicator will quickly flicker.
5.Connect power cord of Wireless RX.
Note:
If there is no audio signal for longer than 10 minutes, the Wireless RX and Wireless TX will be automatically switched to standby mode. LEDs will turn blue when there is any audio signal back.
If you operate main unit then wireless speakers (rear speakers) sound within a few seconds in standby mode.
CAUTION
Rear speaker (wireless speakers) is no sound.
The DC power cable is not connected between the Wireless TX and the Active Subwoofer Speaker.
Connect the Wireless TX and the Active Subwoofer Speaker with the DC power cable.
Power cord of Wireless RX (or Wireless speakers) is not connected.
Connect the Power cord of Wireless RX (or Wireless speakers).
LED indicator of Wireless TX is RED.
-Turn on the main unit.
-Set to sound mode by PL ll MOVIE, PL ll MUSIC or PL ll MATRIX. (page 20)
-Set to XTS ON. (page 20)
-Insert a 5.1 ch sound compatible disc.
If rear speaker (Wireless speakers) is no sound after operating as above, disconnect and connect the power cord of Wireless RX (or Wireless speakers) or set up an ID
of Wireless TX and Wireless RX (or Wireless speakers).
18
Speaker Positioning
In the case of normal position use the 6 speakers (2 front speakers, 1 center speaker, 2 rear speakers and subwoofer).
If you want to play the excellent bass sound, DTS digital surround or Dolby Digital surround, you should connect a subwoofer.
• |
Front speakers |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|||
|
According to your listening position set up the speakers for equal distance. And by hearing position set up the |
<![if ! IE]> <![endif]>Hookupand Settings |
|||||||
|
interval between speakers to 45 degree. |
|
|
|
|
|
|
||
• |
Center speaker |
|
|
|
|
|
|
||
|
|
|
|
|
|
|
|||
|
The center speaker and front speakers are ideally the same height. But normally place it above or below the |
|
|||||||
|
television. |
|
|
|
|
|
|
|
|
• |
Rear speakers |
|
|
|
|
|
|
|
|
|
Place left and right behind the listening area. These speakers recreate sound motion and atmosphere required |
|
|||||||
|
for surround sound playback. For best results, do not install the rear speakers too far behind the listening |
|
|||||||
|
position and install them at or above the level of the listener’s ears. It is also effective to direct the rear |
|
|||||||
|
speakers towards a wall or ceiling to further disperse the sound. |
|
|
||||||
|
In the case of a smaller room size, if the audience is near to the rear wall set the rear speakers opposite each |
|
|||||||
|
other, and set the rear speakers above 60 - 90 cm than the listener’s ears. |
|
|||||||
• Subwoofer |
|
|
|
|
|
|
|
||
|
This can be placed in any front position. |
|
|
|
|
|
|
|
|
|
Subwoofer |
|
|
|
|
|
|
|
|
|
Front Speaker |
Center Speaker |
Front Speaker |
|
|||||
|
(Left) |
|
|
|
|
|
(Right) |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Rear Speaker |
Rear Speaker |
(Left) |
(Right) |
Speaker Positioning Example
19
XTS/XTS pro
Each time you press XTS Pro the setting changes in the following order.
XTS ON → NORMAL → XTS-PRO ON
XTS ON
When playing the movie with the weak bass sound relatively to the general music, it enforces the sense of sound at woofer for you to satisfy with. In the mode of 2 CH BYPASS, It creates the high display effect by playing the sound source via the rear speakers same as the front speakers.
NORMAL
XTS-Pro and XTS mode turn off
XTS-PRO ON
The unique sound quality of the LG Technology creates the optimum sound for you to play the perfect playback of the original sound and to feel the living sound source.
Sound Mode
You can enjoy surround sound simply by selecting one of the pre-programmed sound fields according to the program you want to listen to. (2 ch. sound only)
Press SOUND button repeatedly.
1.PCM
BYPASS → PROLOGIC → MOVIE → MUSIC
→MATRIX → HALL 1 → HALL 2 → THEATER
→BYPASS...
2.Dolby Digital
BYPASS → PROLOGIC → MOVIE → MUSIC
→MATRIX → BYPASS...
Notes:
Initial sound mode is BYPASS.
When recording a TV broadcast or external source to the internal hard disk drive (HDD) or disc, the sound recordings are encoded with Dolby Digital.
Controlling Your TV with the Supplied Remote Control
You can control the sound level, input source, and power switch of your LG/GoldStar TV with the supplied remote.
1.While holding down TV POWER button, press PR v or V.
2.Release TV POWER button.
You can control your TV using the buttons below.
TV Control
Buttons
By pressing |
You can |
POWER |
Turn the TV on or off. |
|
|
INPUT |
Switch the TV’s input source |
|
between the TV and other input |
|
sources. |
|
|
PR v/V |
Scans up or down through |
|
memorized channels. |
|
|
VOL +/– |
Adjust the volume of the TV. |
|
|
Note:
When you replace the batteries of the remote, you may have reset the remote control.
20