LG GT66BPS Owner's Manual [es]

ENGLISH ESPAÑOL

OWNER’S MANUAL

TOP FREEZER
REFRIGERATOR

Please read this manual carefully before operating
your set and retain it for future reference.

Model Name**=color number

LTC20380**
LTC24380**
LTCS20220*

LTCS24223*

GM-T248Q*
GM-U652S*DP
GM-U552S*DP

GM-T208Q*

P/No. MFL67527903 Rev.4

www.lg.com

TABLE OF CONTENTS

TABLE OF CONTENTS

Spanish Version 34

Important Safety Instructions 2-3

Requirements for Ground Connection 3

Parts and Features 4

Refrigerator Installation 5-11

Unpacking 5
Installation 5
How to remove and Install the
Refrigerator Doors 6-8
How to reverse and Install the
Refrigerator Doors 9-11
Closing and Aligning the doors 12

Using your Refrigerator 13-15

Ensuring Proper Air Circulation 13
Adjusting the Controls 13
Adjusting Control Settings 14
Food Storage Guide 14

Refrigerator Shelves 16
Ice tray 16
Pantry Drawer 16
Crisper and Vegetable Drawer 17
Crisper Humidity Control 17
Door Racks 17
Dairy Compartment 17

Refrigerator Care and Cleaning 18-19

Refrigerator Cleaning 18
Outside 18
Inside Walls 18
Door Lining & Gaskets 18
Plastic Parts (Covers and Panel) 18

Back Cover 18

Replacing Refrigerator Lights 18

itpurretnI rewoP
When Going on Vacation 19
When Moving 19

About the Automatic Ice Maker 20

Connecting the Water Line 21-23

Troubleshooting Guide 24-29

Warranty 30-31

91 sno

1

IMPORTANT SAFETY INSTRUCTIONS

SAFETY MESSAGES

This manual contains several important safety notices. Always read and obey all of the following safety messages.

This is the safety alert symbol. This symbol is a warning to potential dangers that could cause death, injury
or damage to you, others or the product. All safety messages will follow after this warning symbol and the
word “DANGER”, “CAUTION” or “WARNING”. These words mean:

DANGER

WARNING

CAUTION

All safety messages inform you of potential danger, advise you on how to reduce the risk of injury and tell you what
can occur if the instructions are not followed.

To reduce the risk of fire, electrical shock or personal
injury, the following precaution measures should be
followed:

• NEVER disconnect the refrigerator by pulling the
power cord, always grip the plug firmly and disconnect
it directly from the outlet.

• Immediately repair or replace all faulty or damaged
service cables. Do not use cords that have cracks or
abrasion damage on the length of the cord or on the
plug.

• When moving your refrigerator, take care not to roll
over the electrical cord.

• DO NOT store or use gasoline or other combustible
liquids or vapors in proximity with this or any other
electrical appliance.

• DO NOT permit children to climb, stand or swing from
the doors or shelves of the refrigerator. This can
serious injury to them and damage to the product.

• Keep your fingers away from areas in which they
can become caught, such as the doors, hinges and
cabinets. Be careful closing the doors when children
are near.

You may be killed or suffer fatal damage if you do not follow instructions.

You may be killed or seriously injured if you do not follow instructions.

Indicates a potentially hazardous situation which, if not avoided, may result in minor injury
or damage to the product.

WARNING

could explode after freezing and cause damage.

• For your safety, this product should be properly
gr

ounded. Have a qualified professional check the
electrical circuit and outlet to ensure a proper ground
connection.

• Read all instructions before utilizing the product. Utilize
this product only as explicitly expressed in this guide.

• Once the refrigerator is operating, avoid touching cold
surfaces of the freezer with damp or wet hands; the
skin could become adhered to these surfaces.

• In refrigerators with an automatic ice dispenser, avoid
contact with moving parts of the ejector mechanism
or with the heating mechanism that discharges the
cubes. DO NOT place your fingers or hands in the
ice dispenser mechanism while the refrigerator is
connected.

cause

• DO NOT refreeze foods which have already thawed.
The Department of Agriculture of the United States, in
your Bulletin of Home and
that:

“...You can refreeze food that has thawed if they contain
ice crystals or are cold and below 40 °F (4 °C)”.

Gardens No. 69 establishes

• Unplug the refrigerator before cleaning or repairing.

NOTE: We strongly recommend that any repair
services be performed by a qualified professional.

• Before replacing a burned-out light bulb, unplug the
refrigerator or shut down the circuit breaker to avoid
contact with a live wire (the bulb could break while
being replaced). NOTE: Setting the control to the OFF
position does not disconnect the power from the light
bulb circuit.

• Do not keep bottles in the freezer compartment, they

WARNING:

after handing.

This product contains chemicals known to the State of California to cause cancer. Wash hands

KEEP THESE INSTRUCTIONS

“...Ground beef, perishable food or seafood that is
discolored or has an unpleasant odor should not be
frozen or consumed. Consumption of melted ice cream
should also be avoided. If the odor or color of food is
questionable, discard it. The food may be dangerous to
consume”.

“Partial thawing or refreezing reduces the quality of the
food, especially fruit, vegetables and prepared meals.
The quality of red meat is less affected than that of
other foods. Use refrozen products as soon as possible
in order to maintain their quality”.

2

CAUTION

This appliance is not intended for use by children, persons with physical or mental disabilities, persons with reduced
sensory or mental capacity, or persons that lack experience or know-how, unless they have supervision or instruction
in relation to the use of the appliance by the person responsible for their safety. Children should be supervised to
assure that they do not play with the appliance.

DANGER:

Children becoming trapped or suffocated is not
a problem of the past. Discarded and abandoned
refrigerators are a hazard, even if they remain there
“for just a few days”. If you would like to dispose of
your old refrigerator, please follow the instructions
below to prevent any accidents.

CHILDREN MAY BECOME TRAPPED

BEFORE DISPOSING YOUR REFRIGERATOR
OR FREEZER WHEN NO LONGER IN USE:

ţ Remove the doors.
ţ Leave the shelves in place so that children

cannot easily become stuck in them.

CFC DISPOSAL

Your old refrigerator may have a cooling system that
uses CFC’s (chlorofluorocarbons). CFC affects the
stratospheric layer of the ozone.

If you decide to throw out your old refrigerator, ensure
that CFC contaminants are properly disposed of by a
qualified professional. If you intentionally remove the
CFC refrigerant, you could be subject to fines or prison
in accordance with environmental legislation in effect.

REQUIREMENTS FOR GROUND CONNECTION

IMPORTANT: Attentively read the following.

TO CONNECT ELECTRICITY

WARNING

ELECTRICAL SHOCK HAZARD

FOR YOUR PERSONAL SAFETY, this appliance must

be properly grounded. Have a qualified electrician
check your wall outlet to ensure that the plug is
grounded properly.

3 prong
grounding type
wall receptacle

3 prong
grounding Ensure proper
plug ground exists
before use

RECOMMENDED GROUNDING METHOD

Your refrigerator must always be plugged to its own
outlet which is adequately grounded. The energy current
should only be 115 V ~ 60 Hz, AC or 127 V ~ 60 Hz, AC
(according to the National rating). and fused at 15 or 20
A. This provides the best performance and prevents an
overload which could cause a fire from the overheating
of the cables. It is recommended that a separate circuit
be used for this appliance, as well as a receptacle that
cannot be disconnected with a switch.

It is your responsibilit
prong outlets with that of an adequately grounded three­prong outlet.

Do not, under any circumstance, cut or extract the third
prong from the plug.

NOTE: Before installation, cleaning or replacing light

bulbs, you must disconnect the appliance from the
power source. When finished, plug the appliance back in
and adjust the thermostat to the desired position.

y and obligation to replace two-

USE OF EXTENSION CABLES

We do not recommend the use of extension cables.

However, if you still choose to utilize an extension cable,
it is absolutely necessary that it is listed in the UL (in
the United States) or CSA (in Canada), that it supports
three-pronged plugs and that the electrical current
support a minimum of 15 A and 120 V.

The use of an extension cable will increase the amount
of space needed behind the refrigerator.

WARNING

REPLACING ELECTRICAL CABLE

If the power cord is damaged, it must be replaced by
our service center or qualified LG technician to avoid
any risk.

Do not use an extension cable.

3

PARTS AND FEATURES

A

B

C

D

E

G

H

O

K

L

F

M

N

I

J

Use this page to become more familiar with the parts and features of your refrigerator. Page references are
included or your convenience.

NOTE: This guide covers several models. The refrigerator you have purchased may have some or all of the items
listed below. The locations of the features shown below may not match your model.

Custom Cube Icemaker* Refrigerator Light (LED)

A

Ice Bin Pantry Drawer

B

Ice Tray* Crispers

C

Freezer Shelf Freezer Light (LED)

D

Freezer Temperature Control Freezer Door Bins

E

Refrigerator Temperature Control Dairy Bin

F

Shelves Refrigerator Door Bins

G

F- Deco Duct

On some models

*

H

I

J

K

L

M

N

O

4

REFRIGERATOR INSTALLATION

2” (5.08 cm)

2” (5.08 cm)

2” (5.08 cm) 2” (5.08 cm)

REFRIGERATOR INSTALLATION

WARNING

EXCESSIVE WEIGHT HAZARD

Use the assistance of two or more persons to move or
install the refrigerator. Not following these instructions
may cause injury to the back and other parts of the
body.

UNPACKING

Before installing your refrigerator, remove any tape
or temporary stickers. Do not remove any stickers
that feature warnings, the model serial number or the
technical label of the product located on the back of the
refrigerator.

To remove adhesive tape residue, rub it well with your
fingers and a little liquid detergent. Clean with warm
water and let dry.

Do not use sharp instruments, rubbing alcohol, flammable
liquids or abrasive cleaning products to remove the
adhesive tape or glue. These products can damage the
surface of your refrigerator. For more information, see
the section on “Important Safety Instructions”.

The shelves come already installed in their factory
position. Remove the shelves and replace them
according to your spacing needs.

Moving Your Refrigerator:

Your refrigerator is extremely heavy. Make sure you
protect the floor when moving your refrigerator for
cleaning or servicing. Always pull your refrigerator
straight out when moving it. Do not shift from side
to side or “walk” the refrigerator when attempting to
move it as this can cause damage to the floor.

WARNING

EXPLOSION HAZARD

INSTALLATION

1. Avoid placing the unit near heat sources, direct

sunlight, or humidity.

2. To avoid vibration, the unit should be leveled. If needed,

adjust the leveling screws to compensate for an
unleveled floor. The front should be slightly taller than
the rear to ensure that the doors close properly. The
leveling screws can easily be turned by slightly tilting
the front of the refrigerator, turning the leveling screws
clockwise (

(

3. Install the refrigerator in an area between 55 °F
(13 °C) and 110 °F (43 °C). If the surrounding temperature

) to lower it.

is lower or higher than previously mentioned, it can
adversely affect the unit.

) to raise it and counter-clockwise

CAUTION: Avoid placing the unit near heat

sources, direct sunlight or humidity.

ONCE INSTALLED

1. Carefully clean your refrigerator and remove and dust

accumulated during shipping.

2. Install accessories such as the ice bin, door racks,

shelves, etc., in their proper places. These are already
packed to prevent any possible damage during
shipping.

3. Leave your refrigerator on for 2 to 3 hours before

storing food inside. Verify that there is a flow of cold air
in the freezer compartment to ensure proper cooling.
Your refrigerator is now re

WARNING:

• Take care when working with the hinges, base cover
and stops, etc. You may injure yourself.

• DO not place your hands or any tools in the air vents,
the base cover or in the bottom of the refrigerator. This
may cause injury or electrical shock.

Keep a Proper Distance from Adjacent Objects

Please keep the refrigerator at an adequate distance
from other objects. Insufficient spacing can reduce the
refrigerator’s freezing efficiency and increase electricity
consumption.

ady for use.

Keep all flammable materials and vapors (such as
gasoline) away from the refrigerator. Not following
these instructions may cause death, explosion or fire

5

REFRIGERATOR INSTALLATION

Hinge Pin

Middle Hinge Bracket

Middle
Hinge Bracket

HOW TO REMOVE AND INSTALL THE REFRIGERATOR DOORS

(For additional support on this topic, including helpful videos, please visit us at: www.lg.com

If entrance is lees than 35 inches wide, the refrigerator’s door will need to be removed.
IMPORTANT: Before starting, turn off and unplug the refrigerator. Remove all food and the racks from the doors.

).

Hex Socket Wrench Phillips Screwdriver No. 2 Flat Head Screwdriver Adjustable Wrench

TOOLS YOU MIGHT NEED OR USE

WARNING

Before you begin, either unplug the refrigerator or

ELECTRICAL SHOCK HAZARD

turn off the power at the circuit breaker or fuse box.
Remove food and any door rack from the refrigerator.
Failure to do so could result in death or serious injury.

1. Removing Freezer Door

• Gently pry off the Top Hinge Cover with a flat head
screwdriver and remove it. See Fig. 1.

Fig. 1

Fig. 3

2. Removing Refrigerator Door

• Loose and remove the two bolts and the screw to
remove the middle hinge bracket from refrigerator
housing (Figure 4). Set parts aside (Figure 5).

• Using 10 mm or 3/8 inch socket wrench, remove
the three bolts and lift the Top Hinge (See Fig. 2). Set
parts aside.

Fig. 2

• Lift freezer door slightly and remove it (See Fig. 3) Set
parts aside.

Fig. 4

Fig. 5

• Lift up door slightly and remove it (See Figure 6).

6

REFRIGERATOR INSTALLATION

REFRIGERATOR INSTALLATION

REFRIGERATOR INSTALLATION

Fig. 6

ţTo replace doors, begin with refrigerator door and then

follow with freezer door.

3. Replacing Refrigerator Door

ţSet door on Bottom Hinge Pin (See Figure 7).
ţPlace hinge pin of middle bracket inside the hinge pin

insert on the top of the door (See Figure 8). Hold the
door in place and line up the hinge with the holes in
the refrigerator housing.

Fig. 7

Bottom
Hinge
Pin

Fig. 9

4. Replacing Freezer Door

ţSet the freezer door onto the Middle Hinge pin (Figure

10).

ţPlace upper hinge in the top of the freezer door and

line up the hinge with the holes in top of refrigerator.
Use the three bolts to fasten the hinge (See Figure 11).

Fig. 10

Fig. 8

ţUse the two bolts and the screw to refasten the middle
hinge with the refrigerator housing. See Figure 9.

Fig. 11

ţCarefully, force the top hinge cover back into place over

hinge (See Figure 12).

Fig. 12

7

REFRIGERATOR INSTALLATION

Hinge Pin

Middle Hinge Bracket

Hinge Pin
Insert Bracket

Hinge Pin Insert

Cover
(on top of
refrigerator)

Hex Socket Wrench Phillips Screwdriver No. 2 Flat Head Screwdriver

HOW TO REVERSE AND INSTALL THE REFRIGERATOR DOORS

You may find it more convenient to have the doors converted from the left opening type (factory installed) to the right
opening type. Directions refer to the right side as the side on your right as you face the unit.

1/4 in
3/8 in
10 mm

TOOLS YOU MIGHT NEED OR USE

WARNING

Before you begin, either unplug the refrigerator or

ELECTRICAL SHOCK HAZARD

turn off the power at the circuit breaker or fuse box.
Remove food and any door rack from the refrigerator.
Failure to do so could result in death or serious injury.

1. Removing Freezer Door

Gently pry off the top hinge cover with a flat head
screwdriver and remove.

Using 10mm or 3/8 inch socket wrench, remove the
three bolts and lift off the top hinge. Set parts aside

Move the Hinge Pin Insert Bracket to the other side of
the door, keeping the same orientation, and move the
Hinge Pin Insert into the hole on the left side of the
bracket.

Reverse the Door Closer/Stop by flipping it over. Place it
on top of the Hinge Pin Insert Bracket, and tighten both
down with the screw.

Slightly lift up the refrigerator door and remove it.

Turn the freezer door upside down on a non-scratch
surface.
Loosen the screw to remove the Door Closer/Stop and
Hinge Pin Insert.

Pry off the cover on the top left side of the refrigerator to
uncover the screw holes.
Set the freezer door and top hinge parts to the side and
remove the refrigerator door.

8

REFRIGERATOR INSTALLATIONREFRIGERATOR INSTALLATION

2. Reversing and Reinstalling Refrigerator Door

Using a ¼” socket wrench, loosen and remove Hinge
Pin from the Middle Hinge Bracket. Remove washer
underneath the middle hinge and set aside.
NOTE: At this point the door will be loose. Slightly lift the
door and remove it.

Using a 3/8’’ socket wrench with a 2-Inch extension
and screwdriver, loosen the two bolts and one screw, and
remove the Bottom Hinge from right side of the housing.

Remove the Decorative Caps on the bottom of the
refrigerator housing. You will need these holes for the
Bottom Hinge.

Loosen and remove the two bolts and use the Phillips
head screwdriver to remove the Middle Hinge Bracket
from the refrigerator housing. Set parts aside.

Remove the washer from the Bottom Hinge Pin.
Using a ¼” socket wrench, loosen and remove the
Hinge Pin from the Bottom Hinge. Reattach the
Hinge Pin to the opposite side of the hinge.
NOTE: This is easier to do while the hinge is still
attached.

Move the Bottom Hinge to the left side of the housing,
keeping the same orientation, and reattach with the
two bolts and one screw. The flat screw must be
placed on the exterior side of the hinge. Move the
Decorative Bolt to the hole on the lower right side
of the housing.

Turn the refrigerator door upside down on a
nonscratching surface. Loosen the two screws

to remove the Bottom Hinge Pin Insert Bracket
with the Hinge Pin Insert.

9

Hinge
Pin Bracket

Hinge Pin
Insert

Hinge
Pin Bracket

Hinge Pin Insert

Middle Hinge
Bracket

Flange

Decorative
Screw

REFRIGERATOR INSTALLATION

Take out the Hinge Pin Insert and move the Bracket to
the other side of the door, keeping the same orientation.
Place the Hinge Pin Insert into the left side of the bracket.
Tighten the Hinge Pin Bracket to the door.

Flip the Middle Hinge Bracket, (flange will now be on
top) position it on left side of the refrigerator and reattach
with two bolts and a Phillips screwdriver. Place the
refrigerator door down over the pin on the bottom hinge.
Place the washer between the refrigerator door and
middle hinge and re-attach Hinge Pin to Hinge Bracket
with a ¼” socket wrench.
NOTE: Bracket has been flipped, but Hinge Pin stays
in the same orientation with its hexagonal end facing
upward.

Insert the Decorative Screw into the outer hole on the
right
side of the housing. Attach cover on the right side. Cover
is force-fitted.

With a flat-head screwdriver, carefully pry off and
remove the cover over the screw holes on the left side of
refrigerator housing.

Remove the outer lower Decorative Screw from the
housing at the area between the freezer and refrigerator
doors. (You will need this hole for the Middle Hinge
Bracket.)

REATTACHING THE DOORS

Place the freezer door down over the Hinge Pin on the
Middle Hinge Pin Bracket.

Place the Upper Hinge Pin on top of the freezer door
and line up the Upper Hinge with holes on top of the
refrigerator. Use the three bolts to replace the Hinge.

10

Cover (on top of
refrigerator)

REFRIGERATOR INSTALLATION

Corners

REFRIGERATOR INSTALLATION

After changing doors, make sure that the corners
of the Door Gaskets are not folded over. To ensure a
good seal, apply a small amount of silicon grease on
the corners of gaskets.

Tighten the bolts. Force-fit Top Hinge Cover over Top
Hinge.

Replace cover on the top left side of the refrigerator
to the right top to cover the holes. Cover is also
force-fitted.

Corners

11

REFRIGERATOR INSTALLATION

CLOSING AND ALIGNING THE DOORS

To avoid vibration, the unit must be leveled. If necessary,
adjust the Leveling Legs to compensate for unevenness
of the floor. The front should be slightly higher than the
rear to aid in door closing.

Your refrigerator has three front leveling screws, one on
the right and one on the left. If your refrigerator seems
unstable or if you would like the doors to close more
easily, simply adjust the inclination of the refrigerator by
following the instructions below:

NOTE: Third leveling screw is used for protection of
hinge lower.

1. Plug the refrigerator into a 3 prong grounded outlet.

Move the refrigerator into its final position.
Use a 11/16” (18 mm) wrench or an adjustable wrench

2.

to adjust the leveling screws (see Figure A), turning
clockwise to raise the side of the refrigerator and

counter-clockwise to lower it. It may take several turns

to adjust it to the inclination you would like.

NOTE: Having someone push against the top of the
refrigerator takes some weight off the leveling screws.
This will make it easier to adjust the screws.

3. Open both doors again and check to make sure that

they close easily. If not, tilt the refrigerator slightly
more to the rear by turning both Leveling Screws
clockwise. It may take several more turns, and you
should turn both Leveling Screws the

same times.

Door Alignment

If the space between your doors is uneven, follow the
instructions below to align the doors:

1. Gently pry off the Top Hinge Cover with

screwdriver and remove.

2. Loosen the Top Hinge Bolts using a 10 mm or 13/32

inch socket wrench or open-end wrench.

3. Have someone hold the freezer door so the space

between the two doors is even, and retighten the top
hinge bolts.

4. Replace the Top Hinge Cover.

Figure A

a flat head

12

USING YOUR REFRIGERATOR

USING YOUR REFRIGERATORREFRIGERATOR INSTALLATION

ENSURING PROPER AIR CIRCULATION

In order to obtain stable temperature, the air must flow
between the freezer and refrigerator sections. As shown
in the illustration below, the cold air enters through
the bottom part and circulates upward. This air returns
below the freezer floor and the rest of the air enters the
refrigerator section through the top vent.

ADJUSTING THE CONTROLS

• Your refrigerator has two controls that allow you to
regulate the temperature the freezer and refrigerator
compartments.

• Refrigerator Control

Initially set the Refrigerator Control on the middle
setting (number 3). To do so, press the TEMPERATURE
ADJUST button until it reaches the middle position
(the third LED turns ON). Leave the refrigerator on this
setting for 24 hours to reach the correct temperature.
After 24 hours, adjust the compar
as you desire. ALWAYS wait 24 hours before you adjust
the temperature. If you want to set the refrigerator
compartment temperature to a warmer temperature
than the current, continue pressing the TEMPERATURE
ADJUST button until it reaches the desired temperature.

TEMPERATURE

ADJUST

• Demo Mode (For Store Use Only)

Demo Mode disables all cooling in
the refrigerator and freezer sections to conserve energy
while on display in a retail store. When activated, OFF
will display on the control panel.

tment temperature

COLDESTCOLD

Do not block any of these vents with packages of food.
This can interrupt the flow of air and cause temperature
and moisture problems.

IMPORTANT: Because air circulates between both
sections, any odors formed in one section will transfer
to the other. You must thoroughly clean both sections to
eliminate odors. To prevent odor transfer and drying out
of food, make
the “Food Storage Guide” section for details).

NOTE:

If you close the fresh food

compartment door applying
more force than necessary,
freezer door may get open and
close again, due internal air flow
of refrigerator.

sure you wrap or cover foods tightly (See

To deactivate:

Press the TEMPERATURE ADJUST button until your
desired temperature setting is reached. The OFF light
will turn off once the Demo Mode is deactivated.

• Freezer Control

The freezer control should come from factory on the
middle setting (number 3). Wait 24 hours before
adjusting the freezer compartment temperature.
the knob to set the freezer temperature as you desire.
ALWAYS wait 24 hours after any adjustment to reach the
desired temperature.

NOTE: Setting at higher number of the Freezer
compartment, the temperature of freezer compartment
becomes colder.

Roll

13

USING YOUR REFRIGERATOR

ADJUSTING CONTROL SETTINGS

Give the refrigerator time to cool down completely before
adding food. It is best to wait 24 hours before adding
food to the refrigerator. The mid-settings indicated in the
previous section should be correct for normal household
refrigerator usage. The controls are set correctly when
milk or juice is cold to your liking and ice cream is firm.

The refrigerator control functions as the thermostat for
the entire appliance. The higher the number setting, the
longer the compressor will run to keep the temperature
colder. The freezer control adjusts the cold air flow from
the freezer to the refrigerator. Setting the freezer control
to a lower temperature keeps more cold air in the freezer
compartment to make it colder.

If you need to adjust the temperature in the refrigerator
or freezer, begin by adjusting the refrigerator first. Wait
24 hours after the refrigerator adjustment to check the
freezer temperature. If it is too warm or too cold, then
adjust the freezer control as well.

Use the settings listed in the table below as a guide.

CONDITION/REASON: RECOMMENDED

REFRIGERATOR section
is too warm

ţOpening the door often
ţAdding a large amount

of food

ţRoom temperature is

very warm

FREEZER section is too
warm/ ice is made too
slowly

ţOpening the door often
ţAdding a large amount

of food

ţRoom temperature is

very low (not cycling
often enough)

ţUsing ice frequently
ţAir vents blocked by

objects

REFRIGERATOR section
is too cold

ţControls not set

correctly for your
conditions

FREEZER section is too
cold

ţControls not set

correctly for your
conditions

ADJUSTMENT:

Adjust the
REFRIGERATOR setting
to the next highest
number and wait 24
hours, then check.

Adjust the FREEZER
setting to the next
highest number and wait
24 hours, then check.

Remove any objects
blocking air flow.

Adjust the
REFRIGERATOR setting
to the next lowest
number and wait 24
hours, then check.

Adjust the FREEZER
setting to the next lowest
number and wait 24
hours, then check.

FOOD STORAGE GUIDE

ITEMS HOW TO STORE

Storing Fresh Food Wrap or store food in the

Butter or
margarine

Cheese Store in original packaging until

Vegetables with
skins (carrots,
peppers)

Fruit Wash and let dry; store in plastic

Leafy Vegetables Remove original packaging and

Fish Consume fish or seafood the

Chef Fresh Store any meat in original airtight,

Leftovers Cover leftovers with plastic

refrigerator in airtight and
moisture-proof material unless
otherwise noted. This prevents
food odor and taste transfer
throughout the refrigerator. For
dated products, check date code
to ensure freshness.

Store opened butter in a covered
dish or in a closed compartment.
When storing a larger quantity,
wrap in freezer packing and
freeze.

you are ready to use it. Once
opened, tightly rewrap with
plastic wrap or aluminum foil.

Place in bags or plastic containers
inside the crisper.

bags in the refrigerator. Do not
wash or pit berries until you
are ready to eat them. Berries
should be selected and kept in
their original packaging (if there
is any) or in a paper bag closed
halfway and set on a shelf.

trim any dirty or discolored parts.
Wash in cold water and drain.
Place in a plastic bag or plastic
container and store in the crisper.

same day purchased.

moisture-proof packaging.
Rewrap if necessary.

wrap or aluminum foil. Plastic
containers with airtight lids can
also be used.

14

USING YOUR REFRIGERATORUSING YOUR REFRIGERATOR

Packaging Recommendations:

ţ UsFseBMFEQMBsUJDcontainers.
ţ UsFQMBsUJDcontainersXJUIBTNPoUIsurface.
ţ PackageXJUIBMVNJOVNfPJMoGIJHIresistance.
ţ WrBQXJUIQBQFSMByeredXJUIQMBstic.
ţ UsewatFSQrooGQMBstic.
ţ UsFrecPNNFOEFEQMBsUJDCBHTtPstorefrozenfoods.

FollowtheseQBDLBHJOHorcontainerinstructionsinorder
tPreBDIUIFCestfreezing

Do not use:

ţ Bread8rBQQJOH
ţ PlasUJDcPOUBJOFSOoUsafefPSstoring.
ţ ContainersXJUIPVUMJETPSseals.
ţ WaxFEQBQFSPSwaxFEQMBstic.
ţ ThinwrBQQJOHQBQFSPSOotwatFSQroof.

Freezing

IMPORTANT:%POoUkFFQCottleTJOUIFfreezFS

cPNQBrUNFOtUIFZNBZFYQMPEFBGterfree[JOHBOE

FortheNaYJNVNuseofyourfreezerdonotstoreexcesT
food.%PnotintroducealargeBNPVOUofunfrozenfPPET
that cannot CF frozen within 24 hours (no NPre UIBO
2 – 3 QPVOET or ,91 kg - 1,36 kg of food QFS squarF
inchofTQBce inthe freezer).Sufficient TQBceNVst CF
leftinorder forthe airtocirculateQrPQFSMZaround UIF
QBDLBHes. Leave enough TQBce in order to close yPVS
refrigeratorXJUIPVUEJGżDVMty.

Storage UJNes can vary EFQFOEJOH on the tZQF BOE
quality of the food, the way itsQBDLBHForQBDLBHJOH
containerused,(incPNQBSJsontoairandIVNJEJty),BOE
the tFNQFratureit CFJOH storedin. Ice crystals fPSNFE
insideyour QBDLBHFareOPSNBM itindicates theairBOE
IVNJEJtZJOTJEFZPVSQBDLBHFIavFcondensed.

NOTE: Let wBSN foods cool off at rPPN tFNQFraturF
for BQQroYJNately 30 NJO then wrBQ accordingly XJUI
theNethodsNFOUJPOBCoveand freeze. BylettingyPVS
wBSNfoodscooloffCFforeyouintroduceUIFN toyPVS
freezFSJUXJMMsaveyPVFOFrgy.

causFEBNBHF

WARNING

Adequateventilationisrequired when using dryicF
%ryiceis$BSCPO%Joxide(CO
Qroducesoxygen,causingdizziness,slightheadacheT

unconsciousnessordeath.%PnotinhaletheseWBQPrT
andQrPQFSMZventilatetherPPNwhileinusePfdryicF

SUFFOCATING DANGER

2).WheniteWBQPratesJU

15

USING YOUR REFRIGERATOR

REFRIGERATOR SHELVES

The glass shelves in your refrigerator are adjustable to
meet your individual storage needs.

Adjusting the shelves to fit different heights of items will
make finding the exact item you want easier. Doing so
will also reduce the amount of time the refrigerator door
is open which will save energy.

IMPORTANT: Do not clean glass shelves with warm water
while they are cold. Shelves may break if exposed to
sudden temperature changes or impact.

NOTE: Glass shelves are heavy. Use special care when
removing them.

Adjusting Shelves

Remove shelves from the shipping position and replace
shelves in the position you want.

To remove a shelf—Tilt up the back of the shelf in the
direction of 1 and lift it in the direction of 2 . Pull
the shelf out.

PANTRY DRAWER (on some models)

To remove the Pantry Drawer:

2

1

Grasp the drawer handle and pull it forward to the drawer
stop. Lift up and pull out.

1

2

To reinstall a shelf—Slide the shelf into the guides
until it stops.

To replace the Pantry Drawer:

Slide the drawer back all the way past the drawer stop.

Ice Tray (On some models)

ţ1PVSQPUBCMFXBUFSUPUIFMFWFM

indicated in the picture. Do not
overfill with water or ice cubes
will be difficult to remove

ţ'PSRVJDLGSFF[FBEKVTUUIF

freezer dial to 3.

Twist the ice tray to remove the
ice cubes

ţ%POPUCFOEUIFJDFUSBZ%PJOH

so may result in damage to the
tray.

ţ5PSFNPWFJDFDVCFTFBTJMZ

pour water on the back of the
tray or soak it in water before
removing ice cubes.

16

USING YOUR REFRIGERATORUSING YOUR REFRIGERATOR

HUMIDITY CONTROLLED CRISPERS

The crispers provide fresher tasting fruit and vegetables
by letting you easily control humidity inside the drawer.

You can control the amount of humidity in the
moisturesealed crispers by adjusting the control to any
setting between VEGETABLES and FRUIT.

ţ VEGETABLES keeps moist air in the crisper for best
storage of fresh, leafy vegetables.
ţ FRUIT lets moist air out of the crisper for best storage
of fruit.

To remove and install the crisper drawers:

1. Pull the crisper drawer out to the drawer stop.

2. Lift the front of the crisper up, then pull it straight out.

3. To install, slightly tilt up the front, insert the drawer into

the frame and push it back into place, past the drawer
stop.

To remove the crisper cover:

1. Remove both crisper drawers.

2. Remove the crisper glass.

3. While holding the support and crisper cover, pull up
and out.

DOOR BINS

The door bins are removable for easy cleaning and
adjustment.

1. To remove the bin, simply lift the bin up and pull
straight out.

To remove the crisper glass:

1. Remove the crisper drawers (as described above).

2. Reach in under the glass and lift up.

3. Gently push the glass up and out.

2. To replace the bin, slide it in above the desired support
and push down until it snaps into place.

NOTE: Some bins may vary in appearance and will
only fit in one location.

DAIRY BIN

1. To remove the Dairy Bin, simply lift up and pull out.

2. To replace the Dairy Bin, slide it in above the desired
support slots and push down until it stops.

17

REFRIGERATOR CARE AND CLEANING

WARNING

EXPLOSION HAZARD

Do not use flammable cleaners. Not following these
instructions can cause death, explosion or fire.

The refrigerator, as well as the freezer, do their own
de-freezing. This process does not prevent the build
up of contaminants, therefore it is suggested that you
clean both parts once a month; clean spilled liquids
immediately.

REFRIGERATOR CLEANING

• Unplug your refrigerator.

• Pull out all of the removable parts (such as the

vegetable and dairy doors).

• Use a clean sponge (or a soft rag) and use it with
lukewarm water mixed with detergent. Do not use
abrasive or concentrated cleaners.

• Hand wash it, and dry it thoroughly.

• Plug the refrigerator back in.

OUTSIDE

Wax the outside in order to create better protection. Make
sure you use a product specifically design to be used
for electro-domestic products (car wax is acceptable).
Use a clean, soft rag, and perform this task twice a year.
For metal-made refrigerators, do not wax, simply clean
it with water and detergent. Do not use concentrated or
abrasive products.

BACK COVER

WARNING

Before you begin, either unplug the refrigerator or turn
off power at the circuit breaker or fuse box.

NOTE: Back Cover should only be
removed by a qualified technician.

In order to get an efficient
performance of your refrigerator,
clean the back cover of it at least
twice a year.

REPLACING REFRIGERATOR LIGHTS

The refrigerator and freezer compartment lights
are LED interior lighting, and service should
be performed by a qualified technician.

ELECTRICAL SHOCK HAZARD

BACK

COVER

WARNING

Before replacing a burned-out light bulb, either unplug
the refrigerator or turn off power at the circuit breaker
or fuse box.

ELECTRIC SHOCK HAZARD

In case of STS, apply cleaner in same direction that hair
line of STS.

NOTE: Avoid the usage of chemical products that
contain phosphates or bleach.

INSIDE (Allow freezer to slightly warm up a small
degree to prevent cloth from sticking)

In order to eliminate bad odors, clean the inside of
the refrigerator with a mixture of baking powder and
lukewarm water (one teaspoon of baking powder per cup
of water). Ensure that the powder dissolves thoroughly, in
order to prevent any sort of damage.

DOOR LINING AND GASKETS

Use only a mild detergent (such as dish soap).

PLASTIC PARTS (Covers and Panels)

Do not use abrasive, paper or rough products. These
could damage the product.

18

REFRIGERATOR CARE AND CLEANING

REFRIGERATOR CARE AND CLEANINGREFRIGERATOR CARE AND CLEANING

POWER INTERRUPTIONS

1. In case of a black out, call your electric company and

ask how long it will last.

2. In case of a 24 hour or less black out, do not open the

refrigerator; this will keep the food fresh.

3. In case of a longer black out, do one of the following

options:

• Pull out all of the frozen food and keep them in an ice
chest.

• Put 2 lbs (907 g) of frozen ice (make sure you use
gloves) for each square foot (28 L) inside the freezer.
This task will preserve the food from 2 to 4 days.

• In case you do not possess neither ice chest or dry ice,
consume your food as soon as possible.

REMEMBER: In a power failure, a full freezer stays cold
longer than a partially filled one. A freezer full of me
stays cold longer than a freezer full of baked goods. If
you see that food contains ice crystals, it may be safely
refrozen, although the quality and flavor may be affected.
If the condition of the food is poor or if you feel it unsafe,
dispose of it.

at

WHEN GOING ON VACATION

If you decide to leave your refrigerator on when going
away, consider these steps:

1. Consume all of the perishable items and freeze the
rest.

2. Empty the ice bin.

When your refrigerator arrives to your home, put
everything back into place and read the
“Refrigerator Installation” in order to ob
preparation. In case your refrigerator has a factory ice
maker, remember you have to reconnect the water
supply.

section

tain installation

If you decide to leave your refrigerator off:

1. Remove all of the food.

2. Unplug your refrigerator.

3. Clean and dry it well.

4. Make sure the doors stay open (use blocks or tape) in

or

der to prevent bad odors and fungi from happening.

WHEN MOVING

If you decide to take your refrigerator with you when
moving, consider the following:

1. Remove all of the food from it, and place the frozen
food in an ice chest with dry ice.

2. Unplug your refrigerator.

3. Empty the water from its tray.

4. Clean and dry it with a rag.

5. Pull out all of the removable parts, and wrap them with

adhe

sive tape.

6. Depending on the model of the refrigerator, lift the top
part of the refrigerator so it can roll with ease, or screw
the levelers so it won´t scratch the floor. Consult to the
section “Closing and Aligning Doors”.

7. Keep the doors closed with the cable glued to the
refrigerator cabinet with an adhesive tape.

19