LG GR-L258STL Owner’s Manual

BOTTOM FREEZER
REFRIGERATOR

User’s Guide

Please read this guide thoroughly before operating and
keep it handy for reference at all times.

P/No. 3828JL8097M

2

TABLE OF CONTENTS

English Version 2

Safety Instructions 3–4

Important Safety Instructions 4

Parts and Features 5

Refrigerator Installation 6–13

Unpacking Your Refrigerator 6

Installation 6

Removing and Replacing
Your Refrigerator Handles
and Doors 7–12

Base Cover 13

Leveling and Door Alignment 13

Using Your Refrigerator 14–24

Setting the Controls 14

Ensuring Proper Air Circulation 14

Diagnosis(Failure Detection)
Function 15

How To Use A New Door Ice
Bucket 16

Adjusting Control Settings 17

Food Storage Guide 17

Storing Frozen Food 18

uu

Refrigerator section

Water Dispenser 18

Refrigerator Shelves 19

Bottle Holder (Optional) 19

Snack Pan 20

Optibin Crisper 20

Crisper Humidity Control 20

Removing Crisper 20

Crisper Cover with Lattice on
inner Surface 21

Dairy Bin (Optional) 21

Modular Door Bin 22

Egg Box (Optional) 22

uu

Freezer section

Tilting Door 22

Tilt- Out Door Basket (Optional) 22

Ice Bin 22

Durabase 23

Durabase Divider 23

Pull out Drawer 23

Filter 24

Care and Cleaning 25–26

General Cleaning Tips 25

Outside 25

Inside Walls 25

Door Liner and Gaskets 25

Plastic Parts 25

Condenser Coils 25

Light Bulb Replacement 25–26

Power Interruptions 26

When you go on vacation 26

When you move 26

About the Automatic Icemaker 27

Connecting the Water Line 28–30

Troubleshooting Guide 31–34

IMPORTANT SAFETY INSTRUCTIONS

This guide contains many important safety messages. Always read and obey all safety messages.

This is the safety alert symbol. It alerts you to safety messages that inform you of hazards
that can kill or hurt you or others, or cause damage to the product.

All safety messages will be preceded by the safety alert symbol and the hazard signal word
DANGER, WARNING, CAUTION. These words mean:

ww

WARNING

To reduce the risk of fire, electric shock, or
injury to persons when using your product,
basic safety precautions should be followed,
including the following:

Read all instructions before using this appliance.

• NEVER unplug your refrigerator by pulling on the
power cord. Always grip the plug firmly and pull it
straight out from the outlet.

• Repair or replace immediately all electric service
cords that have become frayed or otherwise
damaged. Do not use a cord that shows cracks or
abrasion damage along its length or at either the
plug or connector end.

• When moving your refrigerator away from the wall,
be careful not to roll over or damage the power cord.

• DO NOT store or use gasoline or other flammable
vapors and liquids in the vicinity of this or any
other appliance.

• DO NOT allow children to climb, stand or hang on
the refrigerator doors or shelves in the refrigerator.
They could damage the refrigerator and seriously
injure themselves.

• Keep fingers out of pinch point areas; clearances

between the doors and cabinet are necessarily small.
Be careful closing doors when children are in the area.

• Unplug your refrigerator before cleaning or making
any repairs.

NOTE: We strongly recommend that any servicing
be performed by a qualified individual.

• Before replacing a burned-out light bulb, unplug
the refrigerator or turn off power at the circuit
breaker or fuse box in order to avoid contact with a
live wire filament. (A burned-out light bulb may
break when being replaced.)

NOTE: Setting either or both controls to the OFF
position does not remove power to the light circuit.

• This refrigerator must be properly installed in
accordance with the Attention Installer Instructions
that were taped to the front of the refrigerator.

• After your refrigerator is in operation, do not touch
the cold surfaces in the freezer compartment when
hands are damp or wet. Skin may adhere to the
extremely cold surfaces.

• In refrigerators with automatic icemakers, avoid
contact with the moving parts of the ejector
mechanism, or with the heating element that
releases the cubes. DO NOT place fingers or
hands on the automatic icemaking mechanism
while the refrigerator is plugged in.

• DO NOT refreeze frozen foods which have thawed
completely. The United States Department of
Agriculture in Home and Garden Bulletin No. 69 says:

…You may safely refreeze frozen foods that have
thawed if they still contain ice crystals or if they
are still cold—below 4°C.

…Thawed ground meats, poultry or fish that have
any off-odor or off-color should not be refrozen
and should not be eaten. Thawed ice cream
should be discarded. If the odor or color of any
food is poor or questionable, get rid of it. The food
may be dangerous to eat.

Even partial thawing and refreezing reduces the
eating quality of foods, particularly fruits, vegetables
and prepared foods. The eating quality of red meats
is affected less than that of many other foods. Use
refrozen foods as soon as possible to save as
much of their quality as you can.

• Do not modify or extend

the Power Cord length.

It will cause electric shock
or fire.

You will be killed or seriously injured if you don’t follow instructions.

ww

ww

DANGER

You can be killed or seriously injured if you don’t follow instructions.

ww

WARNING

Indicates an imminently hazardous situation which, if not avoided,
may result in minor or moderate injury, or product damage only.

All safety messages will identify the hazard, tell you how to reduce the chance of injury and tell you
what can happen if the instructions are not followed.

ww

CAUTION

3

SAVE THESE INSTRUCTIONS

Junked or abandoned refrigerators are
dangerous… even if they will sit for just a few
days. If you are deposing of your old refrigerator,
please follow the instructions at right to help
prevent accidents.

BEFORE YOU THROW AWAY
YOUR OLD REFRIGERATOR
OR FREEZER

• Take off the doors.

• Leave the shelves in place so
that children may not easily
climb inside.

4

ww

DANGER:

RISK OF CHILD ENTRAPMENT

CFC DISPOSAL

Your old refrigerator may have a cooling system
that used CFCs (chlorofluorocarbons). CFCs are
believed to harm stratospheric ozone.

If you are throwing away your old refrigerator,
make sure the CFC refrigerant is removed for
proper disposal by a qualified servicer. If you
intentionally release this CFC refrigerant, you can
be subject to fines and imprisonment under
provisions of environmental legislation.

IMPORTANT SAFETY INSTRUCTIONS

Don’t use an extension cord

If possible, connect the refrigerator to its own
individual electrical outlet to prevent it and other
appliances or household lights from causing an
overload that could cause a power outage.

Accessibility of Supply Plug

The refrigerator-freezer should be so positioned
that the supply plug is accessible for quick
disconnection when accident happens.

Supply Cord Replacement

If the supply cord is damaged, it must be
replaced by the manufacturer or its service agent
or a similarly qualified person in order to avoid a
hazard.

FEED WATER PIPE INSTALLATION

Before installation

• Automatic ice maker can be installed only by
manufacturer.

• Automatic ice maker operation needs water
pressure of 147~834 kPa (1.5~8.5 kgf/cm

2

)
(That is, an instant paper cup (180 cc) will be
fully filled within 3 sec.).

• If water pressure does not reach the rating
147 kPa (1.5 kgf/cm2) or below, it is necessary
to purchase a separate pressure pump for
normal automatic icing and cool water feed.

• Keep the total length of the feed water pipe tube
within 8 m and be careful for the tube not be
bent. If the tube is 8 m or longer it may cause
trouble in water feed owing to the drain water
pressure.

• Install the feed water pipe tube at a place free
from heat.

ww

WARNING

• Connect to potable water supply only.

• Refer to instructions with water filter kit for
installation.

ww

WARNING

• The refrigerant and insulation blowing gas used
in the appliance require special disposal
procedures. When disposal, please consult with
service agent or a similarly qualified person.

PARTS AND FEATURES

Use this page to become more familiar with the parts and features. Page references are included for
your convenience.

NOTE: This guide covers several different models. The refrigerator you have purchased may
have some or all of the items listed below. The locations of the features shown below may not
match your model.

Refrigerator Light

Filter (Inside)

Modular Door Bins

Refrigerator Shelves

Optibin Crisper
(Keeps fruits and vegetable fresh
and crisper)

Ice Room
(Ice Maker and Ice Bucket)

Pull out Drawer

Turbo Motor

Tilt-Out Door Basket (optional)

Durabase

Divider

Ice Bin

Water Tank Cover

Snack Pan

Egg Box (optional)

Dairy Bin (optional)

Bottle Holder (optional)

5

A
B

C
D

E

F

G

O
P
Q

H

I

J

L

K

M

N

Q

A

B

F

N

M

E

L

I

H

G

K

J

P

C

D

Q

C

O

Ice Bucket

Ice Room Door

REFRIGERATOR INSTALLATION

UNPACKING YOUR REFRIGERATOR

Remove tape and any temporary labels from your
refrigerator before using. Do not remove any
warning-type labels, the model and serial number
label, or the TechSheet that is attached to back
wall of the refrigerator.

To remove any remaining tape or glue, rub the
area briskly with your thumb. Tape or glue residue
can also be easily removed by rubbing a small
amount of liquid dish soap over the adhesive with
your fingers. Wipe with warm water and dry.

Do not use sharp instruments, rubbing alcohol,
flammable fluids or abrasive cleaners to remove
tape or glue. These products can damage the
surface of your refrigerator. For more information,
see the Important Safety Instructions section.

Refrigerator shelves are installed in the shipping
position.

Please reinstall shelves according to your
individual storage needs.

INSTALLATION

1. To avoid vibration, the unit must be level. If

required, adjust the leveling screws to
compensate for unevenness of the floor. The
front should be slightly higher than the rear to
aid in door closing. Leveling screws can be
turned easily by tipping the cabinet slightly. Turn
the leveling screws clockwise ( ) to raise the
unit, counterclockwise ( ) to lower it.

2. Install this appliance in an area where the

temperature is between 13°C and 43°C. If the
temperature around the appliance is too low or
high, cooling ability may be adversely affected.

3. To ensure proper air circulation around the

fridge-freezer, please maintain sufficient space
on both the sides as well as top and maintain
at least 2 inches(5cm) from the rear wall.

ww

CAUTION: Avoid placing the unit near heat
sources, direct sunlight or moisture.

NEXT

1. Clean your refrigerator thoroughly and wipe off

all dust accumulated during shipping.

2. Install accessories such as ice cube bin,

drawers, shelves, etc., in their proper places.
They are packed together to prevent possible
damage during shipment.

3. Let your refrigerator run for at least 2 or 3 hours

before putting food in it. Check the flow of cold
air in the freezer compartment to ensure proper
cooling. Your refrigerator is now ready for use.

ww

WARNING

• Be careful when you work with hinge, base
grille, stopper etc. You may be injured.

• Do not put hands or foot or metal sticks into air
vents, base grille or bottom of refrigerator. You
may be injured or receive an electrical shock.

6

ww

WARNING

Excessive Weight Hazard

Use two or more people to move and install
refrigerator.

Failure to do so can result in back or other injury.

ww

WARNING

When Moving Your Refrigerator:

Your refrigerator is heavy. When moving the
refrigerator for cleaning or service, be sure to
protect the floor. Always pull the refrigerator
straight out when moving it. Do not wiggle or
walk the refrigerator when trying to move it, as
floor damage could occur.

ww

WARNING

Explosion Hazard

Keep flammable materials and vapors, such as
gasoline, away from refrigerator.

Failure to do so can result in death, explosion
or fire.

REFRIGERATOR INSTALLATION

7

HOW TO REMOVE DOOR HANDLES

To move refrigerator through a house door, it may be necessary to remove the refrigerator door
handles.

NOTE: Handle appearance may vary

from illustrations on this page.

1. Removing Refrigerator Handle

• Grasp the handle tightly with
both hands and slide the handle
up (1)(this may require some
force).

• The keyhole slots (2) on the back
of the handle allow the handle to
separate from the mounting
screws (3).

w CAUTION: The handle could be

damaged if you hit it with a
hammer while removing or
attaching.

w CAUTION: When you assemble

or disassemble handle, you must
push or pull with reasonable
force.

2. Removing Freezer Drawer Handle

• Press the handle against door
first.

• Grasp the handle tightly with
both hands and slide the handle
to right (1)(this may require some
force).

• The keyhole slots (2) on the back
of the handle allow the handle to
separate from the mounting
screws (3).

1

1

3

2

3

1

1

2

Screws

mounted

on door

Screws

mounted

on door

Keyhole slots
on back of
handle

Keyhole slots
on back of
handle

REFRIGERATOR INSTALLATION

8

HOW TO REPLACE DOOR HANDLES

NOTE: Handle appearance may vary from

illustrations on this page.

1. Replacing Refrigerator Door Handle

• Align keyhole slots (1) on the top

and bottom of the back of the handle
with the screws (2) mounted on the
front of the door.

• Press the handle against the door

front, making sure that the screws
(2) go into the keyhole slots (1).

• Holding the handle with both hands,

press it firmly against the front of the
door and slide the handle down (3).

2. Reinstalling the Freezer Drawer
Handle

• Align keyhole slots (4) on the right
and left sides of the back of the
handle with the screws (5) mounted
on the front of the drawer.

• Press the handle against the drawer
front, making sure that the screws
(5) go into the keyhole slots (4).

• Holding the handle with both hands,
press it firmly against the front of the
drawer and slide the handle to the
left (6).

2

3

1

1

6

6

5

4

Screws

mounted

on door

Screws

mounted

on door

Keyhole slots
on back of
handle

REFRIGERATOR INSTALLATION

REMOVING AND REPLACING REFRIGERATOR DOORS

1. Removing Refrigerator Door

w CAUTION: Before you begin, unplug the refrigerator. Remove food and bins from doors.
uu

Left Door - FIG.2

1. Disconnect water supply tube by pushing back on the disconnect ring (4). - FIG.1

2. Open door. Loosen top hinge cover screw (1).
Use flat tip screwdriver to pry back hooks on front underside of cover (3). Lift up cover.

3. Disconnect door switch wire harness (2). Remove cover.

4. Pull out the tube.

5. Disconnect the three wire harnesses (5). Remove the grounding screw (6).

6. Rotate hinge lever (7) counterclockwise and remove. Lift top hinge (8) free of hinge lever latch (9).

w CAUTION: When lifting hinge free of latch, be careful that door does not fall forward.

7. Lift door up from middle hinge pin and remove door.

8. Place door, inside facing up, down onto a non-scratching surface.

uu

Right Door - FIG.3

1. Open door. Loosen top hinge cover screw (1). Lift up cover (3).

2. Disconnect door switch wire harness (2). Remove cover.

3. Disconnect wire harness (5). Remove the grounding screw (6).

4. Rotate hinge lever (7) clockwise and remove. Lift top hinge (8) free of hinge lever latch (9).

w CAUTION: When lifting hinge free of latch, be careful that door does not fall forward.

5. Lift door up from middle hinge pin (10) and remove door.

6. Place door, inside facing up, down onto a non-scratching surface.

9

FIG.3

FIG.1

4

1

7

8

3

2

6

5

9

1

7

8

3

2

6

5

9

FIG.2

3

1

4

6

2

7

8

9

5

REFRIGERATOR INSTALLATION

2. Reinsalling the Refrigerator Door

uu

Right Door

1. Lower the door onto middle hinge pin (10).

2. Fit top hinge (8) over hinge lever latch (9) and into place. Insert hinge lever (7) under lever latch. Rotate
lever counterclockwise to secure hinge.

3. Install the grounding screw (6) and connect the three wire harnesses (5).

4. Connect door switch wire harness (2).

5. Hook tab on door switch side of cover under edge of wire opening in cabinet top. Position cover (3)
into place. Insert and tighten cover screw (1).

uu

Left Door

1. Lower the door onto middle hinge pin (10).

2. Fit top hinge (8) over hinge lever latch (9) and into place. Insert hinge lever (7) under lever latch. Rotate
lever clockwise to secure hinge.

3. Install the grounding screw (6) and connect the three wire harnesses (5).

4. Connect door switch wire harness (2).Push the water supply tube into the hall on the top case and pull
it out on the backplate.

5. Insert the water supply tube (4) into the connector tube until you see only one scale mark.
(Fully insert the tube over 5/8”(15mm)).

6. Hook tab on door switch side of cover (3) under edge of wire opening in cabinet top. Position cover
into place. Insert and tighten cover screw (1).

10

10

10

Correct

Incorrect

REFRIGERATOR INSTALLATION

11

HOW TO REMOVE AND INSTALL
THE PULLOUT DRAWER

IMPORTANT: To avoid possible injury or product

or property damage, you will need two people to
perform the following instructions.

1. Removing Pullout Drawer

• Pull the drawer open to full extension. Remove
the lower basket (1) by lifting basket from rail
system.
(If you tilt the door, it will be easier.)

• Press both hangers with your thumbs to lift it up.

• Separate the left and right rail cover

• Remove the screws(2) of the rail on both sides.

• With both hands, hold both sides of the door

and pull it up to separate it from the rails.

• With both hands, hold the center bar and push it
in to let both rails fitted simultaneously.

w CAUTION: When you remove the drawer, do

not hold the handle. If it may come off and it
could cause personal injury.

w CAUTION: When laying the drawer down, be

careful not to damage the floor or hurt your
feet by the sharp edges on hinge side.

1

2