OWNER’S MANUAL
COMMERCIAL WASHER
Please read this manual carefully before operating
your set and retain it for future reference.
MODEL
GCW1069QS
GCW1069CS
P/No. : MFL62526841
www.lg.com
2
PRODUCT FEATURES
CONTENTS
■
Direct Drive System
The advanced Brushless DC motor directly drives the drum without
using a belt and pulley.
■
Tilted Drum and Extra Large Door Opening
The tilted drum and extra large opening make it possible to load
and unload clothing more easily.
■
Ultra Capacity
The larger drum enables more tumbling action and greater centrifugal
force, but also less tangling and wrinkling of the laundry. Heavier
loads, such as king size comforters, blankets, and curtains, can be
washed.
■
See-through Door and Big Door
You can see the laundry throughout the cycle.
■
Stainless Steel Drum
The stainless steel drum doesn't rust.
PART 1. IMPORTANT SAFETY INSTRUCTIONS ...........................................................................3
PART 2. SPECIFCATIONS...............................................................................................................6
PART 3. IDENTIFICATION ...............................................................................................................7
PART 4. OPERATING YOUR WASHER ..........................................................................................9
PART 5. PROGRAMMING MODE..................................................................................................10
PART 6. ERROR MODE.................................................................................................................46
PART 7. POWER FAIL RECOVERY ..............................................................................................47
PART 8. DEFAULT WASHER SETTINGS......................................................................................47
PART 9. WARRANTY.....................................................................................................................48
3
Part 1 IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion,
electric shock, or to prevent property damage, personal injury, or loss of life.
IMPORTANT SAFETY INSTRUCTIONS
• Read all instructions before using the washer.
• Do not wash articles that have been previously cleaned
in, washed in, soaked in, or spotted with gasoline, dry
cleaning solvents, or other flammable or explosive
substances, as they give off vapors that could ignite or
explode.
• Do not add gasoline, dry cleaning solvents, or other
flammable or explosive substances to the wash water.
These substances give off vapors that could ignite or
explode.
• Under certain conditions, hydrogen gas may be
produced in a hot water system that has not been used
for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE.
If the hot water system has not been used for such a
period, before using the washing machine, turn on all
hot water faucets and let the water flow from each for
several minutes. This will release any accumulated
hydrogen gas. As the gas is flammable, do not smoke
or use an open flame during this time.
• Do not allow children to play on or in the washer.
Close supervision of children is necessary when the
washer is used near children.
• Before the washer is removed from service or
discarded, remove the door to prevent children from
hiding inside.
• Do not install or store the washer where it will be
exposed to the weather.
• Do not tamper with the controls.
• Do not repair or replace any part of the washer or
attempt any servicing unless specifically
recommended in the user-maintenance instructions or
published user-repair instructions that you understand
and have the skills to carry out.
• See Installation Instructions for grounding
requirements.
• ALWAYS follow the fabric care instructions supplied by
the garment manufacturer.
• Do not place items exposed to cooking oil in your
washer. Items contaminated with cooking oils may
contribute to a chemical reaction that could cause a
load to catch fire.
• Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of the
fabric softener or product.
WARNING: To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic
precautions, including the following:
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of
electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord
having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate
outlet that is properly installed and grounded in accordance with all local codes and ordinances.
• Do not use an adapter or extension cord.
• Do not remove ground prong.
• If you don’t have the proper outlet, consult an electrician.
GROUNDING INSTRUCTIONS
Your safety and the safety of others are very important.
WARNING:
Improper connection of the equipment-grounding conductor can result in risk of electric shock. Consult a
qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded.
Do not modify the plug provided with the appliance - if it does not fit the outlet, have a proper outlet installed
by a qualified electrician.
!
!
!
DANGER: You can be killed or seriously injured if you don’t follow instructions.
!
WARNING: You can be killed or seriously injured if you don’t follow instructions.
!
!
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can
happen if the instructions are not followed.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others.
All safety messages will follow the safety alert symbol and either the word DANGER or WARNING.
These words mean:
SAVE THESE INSTRUCTIONS
Part 1 IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
!
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire
or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
SAFETY INSTRUCTION FOR INSTALLATION
!
WARNING!
To reduce the risk of fire, electric shock, or injury to persons when using the appliance,
follow basic precautions, including the following:
• Refer to INSTALLATION INSTRUCTIONS for
detailed grounding procedures.
Installation instructions are packed in the washer for
installer's reference. If the washer is moved to a new
location, have it checked and reinstalled by a qualified
service person. Failure to follow this warning can cause
serious injury, fire, electrical shock or death.
• Do not, under any circumstances cut or remove the
third (ground) prong from the power cord.
Failure to follow this warning can cause serious injury, fire,
electrical shock or death.
• For personal safety, this appliance must be properly
grounded.
Failure to follow this warning can cause serious injury, fire,
electrical shock or death.
• The power cord of this appliance is equipped with a 3prong (grounding) plug which fits a standard 3-prong
(grounding) wall outlet to minimize the possibillty of
electric shock hazard from this appliance.
• This washer must be plugged into a 120-VAC, 60-Hz
grounded outlet. Failure to follow this warning can cause
serious injury, fire, electrical shock, or death.
• Have the wall outlet and circuit checked by a qualified
electrician to make sure the outlet is properly grounded.
Failure to follow this warning can cause serious injury, fire,
electrical shock, or death.
• Where a standard 2-prong wall outlet is encountered, it
is your personal responsibility and obligation to have it
replaced with a properly grounded 3-prong wall outlet.
Failure to follow this warning can cause serious injury, fire,
electrical shock, or death.
• Do not install on carpet. Install the washer on a solid
floor. Failure to follow this warning can cause serious leak
damage.
• Do not remove the ground prong.
Do not use an adapter or extension cord.
Plug into a grounded 3 prong outlet.
Failure to follow this warning can cause serious injury, fire,
electrical shock, or death.
• The washer should always be plugged into its own
individual electrical outlet which has a voltage rating
that matches the rating plate.
This provides the best performance and also prevents
overloading house wiring circuits which could cause a fire
hazard from overheated wires.
• Never unplug your washer by pulling on the power
cord. Always grip the plug firmly and pull straight out
from the outlet. Failure to follow this warning can cause
serious injury, fire, electrical shock, or death.
• Repair or replace all power cords that have become
frayed or otherwise damaged.
Do not use a cord that shows cracks or abrasion
damage along its length or at either end.
Failure to follow this warning can cause serious injury, fire,
electrical shock,or death.
• When installing or moving the washer, be careful not to
pinch, crush, or damage the power cord. Failure to
follow this warning can cause serious injury, fire, electrical
shock, or death.
• The washer must be installed and electrically grounded
by a qualified service person in accordance with local
codes, to prevent shock hazard and assure stability during
operation.
• The washer is heavy.
Two or more people are needed to install and move the
appliance.
Failure to do so can result in back or other injury
• Store and install the washer where it will not be
exposed to temperatures below freezing or exposed to
outdoor weather conditions.
Failure to follow this warning can cause serious leak
damage.
• Do not install the washer in humid spaces to reduce
the risk of electric shock.
Failure to follow this warning can cause serious injury, fire,
electrical shock, or death.
• To reduce the risk of personal injury, adhere to all
industry recommended safety procedures including
the use of long sleeved gloves and safety glasses.
Failure to follow all of the safety warnings in this manual
could result in property damage, personal injury or death.
• Keep the area underneath and around your appliances
free of combustible materials such as lint, paper, rags,
chemicals, etc. Failure to do so can result in fire.
4
5
Part 1 IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
SAFETY INSTRUCTION FOR SAFETY USE/CLEANING/CARE/DISCARD
WARNING!
For your safety, the information in this manual must be followed to minimize the risk of fire
or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.
WARNING!
To reduce the risk of fire, electric shock or injury to persons when using the appliance,
follow basic precautions, including the following:
• Unplug the washer before cleaning to avoid the risk
of electric shock.
• Never use harsh chemicals, abrasive cleaners, or
solvents to clean the washer.
They will damage the finish.
• Do not put oily or greasy rags or clothing on top of
the washer. These substances give off vapors that
could ignite the materials.
• Do not wash items that are soiled with vegetable or
cooking oil. These items may contain some oil after
laundering. Due to the remaining oil, the fabric may
smoke or catch fire by itself.
• Disconnect this appliance from the power supply
before attempting any user maintenance.
Turning the controls to the OFF position does not
disconnect this appliance from the power supply.
Failure to follow this warning can cause serious injury,
fire, electrical shock, or death.
• Do not combine laundry products for use in 1 load
unless specified on the label. Do not mix chlorine
bleach with ammonia or acids such as vinegar.
Follow package directions when using laundry
products. Incorrect usage can produce poisonous gasresulting in serious injury or death.
• Do not reach into the washer while parts are
moving. Before loading, unloading, or adding
items,
push in the cycle selector knob and allow the drum
to coast to a complete stop before reaching inside.
Failure to follow this warning can cause serious injury,
fire, electrical shock, or death.
• Do not allow children to play on or in the washer.
Close supervision of children is necessary when the
washer is used near children. As children grow, teach
them the proper, safe use of all appliances.
Failure to comply with these warnings could result in
serious personal injuries.
• Destroy the carton, plastic bag, and other packing
materials after the washer is unpacked.
Children might use them for play.
Cartons covered with rugs, bedspreads or plastic sheets
can become airtight chambers. Failure to comply with
these warnings could result in serious personal injuries.
• Keep laundry products out of children's reach.
To prevent personal injury, observe all warnings on
product labels. Failure to comply with these warnings
could result in serious personal injuries.
• Remove the door to the washing compartment to
avoid the danger of children or small animals getting
trapped inside before your washer is removed from
service or discarded.
Failure to do so can result injury or death.
• Before the washer is removed from service or
discarded, remove the washer door to prevent
accidental entrapment.
Failure to comply with these warnings could result in
serious personal injuries.
!
!
Part 2 SPECIFICATIONS
Shipping Bolts (4)
Power Plug
• If the supply cord is damaged, it
must be replaced by the
manufacturer or an authorized
service technician in order to
avoid a hazard.
Control Panel
Drain Hose
Dispenser
Water Circulation
Drum
Door
Back of Washer
Cold Water Inlet
Lower Cover Cap
Air Vent for Safety Hot Water Inlet
Adjustable Feet
Drain Pump FilterDrain Plug
■
Name: Front-loading Washing Machine
■
Power supply: 120V~ 60Hz
■
Size: 686 mm (W) X 767 mm (D) X 982 mm (H), 129.1 cm (D with door open)
27”(W) X 29
■
Weight: 190 lbs. (87 kg)
■
Wash capacity: 3.63 cu.ft (IEC:4.2 cu.ft)
■
Spin speed: 1150 rpm max.
■
Permissible water pressure: 14.5~116 psi (100~800 kPa)
3
/
”(D) X 38
4
11
/
”(H), 50
16
13
/
”(D with door open)
16
Note
Specifications subject to change by manufacturer.
■
Accessories
6
Part 3 IDENTIFICATION
"
!
"
!
■ CARD TYPE
- SIDE BY SIDE (GCW1069CS)
■ COIN TYPE
- SIDE BY SIDE (GCW1069QS)
1. DISPLAY LED
2. CYCLE BUTTON
3. START BUTTON
4. STATUS BUTTON
7
Part 3 IDENTIFICATION
"
!
DISPLAY LEDSTATUS LED CYCLE BUTTON
START BUTTON
11
DISPLAY LED
The display shows the vend price and remaining time
and programming options. Error codes are also
displayed here.
22
CYCLE BUTTON
Press the CYCLE button to select the desired cycle
based on laundry types and conditions.
WHITES
Use for hot washing for heavy fabrics, such as white
clothes, table linens, and heavily soiled clothes.
COLORS
Use for warm washing for heavy fabrics, such as
jeans, corduroys, or work clothes.
33
START BUTTON
The START LED flashes when the full vend price
has been satisfied and the cycle has been chosen.
44
STATUS LED
• LED flashes whenever the washing cycle
is in operation.
• LED flashes whenever the Rinsing cycle is
in operation.
• LED flashes whenever the Spining cycle is
in operation.
• LED flashes whenever the door
lock is activated.
DELICATES
Use for cold washing for synthetic fabrics, such as
washable knit fabric and no-iron finishes.
PERMANENT PRESS
Use for warm washing for sturdy fabrics, such as
work casual work.
8
9
Part 4 OPERATING YOUR WASHER
The cycle LEDs flash at the same time, when the price
of cycles are equal.
11
Ready mode
Insert a cash card that has a sufficient balance.
The card balance should be more than the programmed
vend price for a selected cycle.
■ Insert a sufficient amount of change that is more
than the programmed vend price for the selected
cycle.
22
Insert card/coin
Press the desired button and press the start button.
The display LED will show the remaining time and
the selected cycle starts.
33
Select the cycle
You cannot change the course while the machine is
running.
55
Change course
The machine stops and LED display shows “End”
with beeper sound.
66
Cycle finish
Wash time or rinse cycle can be added when additional
coin is inserted or a valid cash card is entered.
(See page 21 for detailed information)
❋ Do not work any button and stop the washer
(When the washer is operating) or (when a cycle is
in progress)
44
Add super wash
When the card balance is not enough,
machine displays the card balance for 5 seconds
and then displays message repetitively
Note
The machine will not start until sufficient coins
are inserted.
Note
■ Select cycles designed for different
types of fabric and soil levels.
CYCLE
WHITES
Cotton, linen,
towels, shirts,
sheets
Hot/Cold High
COLORS
Mixed loads,
work clothes,
jeans, shirts
Warm/
Cold
High
DELICATES
Dress shirts,
blouses, nylons,
sheer or lacey
garments
Cold/ Cold
Low
PERM
PRESS
Dress shirts,
pants, wrinklefree clothing,
cotton/poly
blend clothing,
tablecloths
Warm/
Cold
Medium
Fabric type
Wash/Rinse
Temp.
Spin Speed
Part 5 PROGRAMMING MODE
❁ Programming mode
: You can check machine information or change setting on “Program setup”, “Collect Information Data”, ”Diagnostic Test”.
There are two methods that you can enter programming mode.
❁ Case1. Check the programming mode by button
How to enter "Programming mode"
You can enter programming mode
only for Idle state and pause state.
- Card Type
1) Insert service card.
2) Display will show “LqC1”
- Coin Type
1) Dissemble upper coin box key.
2) take out the coin drop from the coin box.
3) Turn on/off the toggle switch at the back of the
coin box.
4) Display will show “Lqc1”.
Coin Box Key
Coin Vault
Openings : close
How to use button
You can change Washer vend price, cycle time and
Cycle parameters, etc.
Press Button
WHITES
COLORS
DELICATES
START
Comes back to Idle State
Move to the modes in the
Insert Debit Card
Description
Move to upper level or
Move to the mode in the
same level (+)
same level (-)
Enter the selected mode
- COIN TYPE
Note
• If you turn on the power without connecting meter case for the first time, the machine display “LqC1”.
• When the machine is came out from the factory, it is set in the coin type. You can change Card/Coin type by
button. (For more information refer to SETUP mode’s Featur1.)
10
--
CARD TYPE
-
11
Part 5 PROGRAMMING MODE
• Do not use , .
• It is only used in inspecting the machine.
Note
1. Turn on/off toggle switch or Insert service card, for entering set up mode.
2. Press WHITES button to move to the upper level.
3. Press COLORS(+) or DELICATES(-) button if you want to be at the same level.
4. Press START button to enter the details of Set up, Diagnostic Tests.
is to set price value, time value, and vend type etc.
consists of line test, reset, free cycle, and kill cycle.
Is to collect the usage data.
■ Algorithm flow chart shows how to control programming mode.
■ Before program set, check the structure of programming mode.
■ STRUCTURE OF PROGRAMMING MODE
12
Part 5 PROGRAMMING MODE -
Setup Mode
Setup Mode : (display)
■ You can change washer vend price, cycle time, and cycle parameters, etc.
■ Entering set up mode
Coin type - Turn on/off toggle switch.
Card type - Insert the service card.
Then, the washer displays .
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the START button.
Display previous regular price.
Press COLORS(+) or DELICATES(-) button to set the regular
price.
(The vend price can be set from 0 to 9.95 in 5¢ increments.)
Press the START button.
The machine sets up the regular price, then advances to the
next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
11
How to change regular price.
Button Display
13
Part 5 PROGRAMMING MODE -
Setup Mode
22
How to change regular cold price.
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous regular cold price.
Press COLORS(+) or DELICATES(-) button to set the regular
cold price.
(The vend price can be set from 0 to 9.95 in 5¢ increments.)
Press the START button.
The machine sets up the regular cold price, then advances to
the next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
14
Part 5 PROGRAMMING MODE -
Setup Mode
33
How to change regular warm price
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the “DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous regular warm price.
Press COLORS(+) or DELICATES(-) button to set the regular
warm price.
(The vend price can be set from 0 to 9.95 in 5¢ increments.)
Press the START button.
The machine sets up the regular warm price, then advances to
the next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
15
Part 5 PROGRAMMING MODE -
Setup Mode
44
How to change regular hot price
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous regular hot price.
Press COLORS(+) or DELICATES(-) button to set the regular
hot price.
(The vend price can be set from 0 to 9.95 in 5¢ increments.)
Press the START button.
The machine sets up the regular hot price, then advances to
the next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
16
Part 5 PROGRAMMING MODE -
Setup Mode
55
How to change special price
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous special price.
Press COLORS(+) or DELICATES(-) button to set a special
price.
(The vend price can be set from 0 to 9.95 in 5¢ increments.)
Press the START button.
The machine sets up the special price, then advances to the
next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
17
Part 5 PROGRAMMING MODE -
Setup Mode
66
How to change special cold price
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous special cold price.
Press COLORS(+) or DELICATES(-) button to set the special
cold price.
(The vend price can be set from 0 to 9.95 in 5¢ increments.)
Press the START button.
The machine sets up the special cold price, then advances to
the next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
18
Part 5 PROGRAMMING MODE -
Setup Mode
77
How to change special warm price
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous special warm price.
Press COLORS(+) or DELICATES(-) button to set the special
warm price.
(The vend price can be set from 0 to 9.95 in 5¢ increments.)
Press the START button.
The machine sets up the special warm price, then advances to
the next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
19
Part 5 PROGRAMMING MODE -
Setup Mode
88
How to change special hot price
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous special hot price.
Press COLORS(+) or DELICATES(-) button to set the special
hot price.
(The vend price can be set from 0 to 9.95 in 5¢ increments.)
Press the START button.
The machine sets up the special hot price, then advances to
the next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
20
Part 5 PROGRAMMING MODE -
Setup Mode
99
How to change add super wash price
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous add super wash price.
Press COLORS(+) or DELICATES(-) button to set add super
wash price.
(The vend price can be set from 0 to 9.95 in 5¢ increments.)
Press the START button.
The machine sets up the add super wash price, then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
21
Part 5 PROGRAMMING MODE -
Setup Mode
1100
How to change add super wash type
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous add super wash type.
Press the COLORS or the DELICATES
button and then select the add super wash type you want.
Press the START button.
The machine sets up the add super wash type, then advances
to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
Wash time increase.
Both (Wash time increase and
rinsing once more.)
Rinsing once more.
22
Part 5 PROGRAMMING MODE -
Setup Mode
• Special price days apply or not
• Clear escrow enable or not (coin type only)
• Add super wash apply or not
• Select vend type
• Sense dry apply or not (only for dryer)
Pre-wash apply or not
Top off apply or not (only for dryer)
■ Structure of
1111
How to enter the
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Button Display
■ Content of
23
Part 5 PROGRAMMING MODE -
Setup Mode
1111--11
Special price day setup
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display
.
Press the START button.
Press COLORS or DELICATES button and then select
or
.
Press the START button.
The machine sets up the special price day
,then advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
Disable
One or the other will
display.
Enable
24
Part 5 PROGRAMMING MODE -
Setup Mode
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display
.
Press the COLORS or the DELICATES button until
appears in the display.
Press the START button.
Press COLORS or DELICATES button and then select
or
.
Press the START button.
The machine sets up the clear escrow application
,then advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
Disable
One or the other will
display.
Enable
1111--22
Clear escrow setup - Applied only to coin type
If the total of the coins inserted is greater than the setup price, there are two choices.
1. If CLEE Enab is selected, clear the cycle and display the balance.
2. If CLEE Disb is selected, clear the cycle and do not display the balance.
25
Part 5 PROGRAMMING MODE -
Setup Mode
1111--33
Add super wash setup
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display
.
Press the COLORS or the DELICATES button until
appears in the display.
Press the START button.
Press COLORS or DELICATES button and then select
or
.
Press the START button.
The machine sets up the add super wash application
,then advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
Disable
One or the other will
display.
Enable
Part 5 PROGRAMMING MODE -
Setup Mode
26
1111--44
Vend type setup - card type or coin type setup
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display
.
Press the COLORS or the DELICATES button until
appears in the display.
Press the START button.
Press COLORS or DELICATES button and then select
or
.
Press the START button.
The machine sets up the vend type
,then advances to the next process automatically.
1.Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
Coin type
One or the other will
display.
Card type
After setting the Value to VEND, vend type is changed directly without power on/off
SEdE(Sense dry) is not available in washer
Note
27
Part 5 PROGRAMMING MODE -
Setup Mode
1111--55
Pre-wash set up
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display
.
Press the START button.
Press COLORS or DELICATES button and then select
or
.
Press the START button.
The machine sets up the special price day.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
Disable
One or the other will
display.
Enable
toFF (top off ) is not available in washer (Only for dryer)
Note
28
Part 5 PROGRAMMING MODE -
Setup Mode
1122
How to enter the special price day
Entering set up mode.
You will see LqC1
Press the WHITES button
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display
.
Button Display
■ Structure of
Sunday
Monday
Tuesday
Wednesday
Thursday
Friday
Saturday
29
Part 5 PROGRAMMING MODE -
Setup Mode
1122--11
How to change to Sunday
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display
.
Press the START button.
Press COLORS or DELICATES button and then select
or
.
Press the START button.
The machine sets up the special price day (Sunday)
,then advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
Disable
One or the other will
display.
Enable
As explained on the previous page, similarly, other days can be set up by the same method.
Note
30
Part 5 PROGRAMMING MODE -
Setup Mode
1133
Special price beginning time setup
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous special price beginning time.
Press COLORS(+) or DELICATES(-) button to select time
between 0 and 23.
Press the START button.
The machine sets up the special price beginning time, then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
31
Part 5 PROGRAMMING MODE -
Setup Mode
1144
Special price ending time setup
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous Special Price ending time.
Press COLORS(+) or DELICATES(-) button to select time
between 0 and 23.
Press the START button.
The machine sets up the special price ending time, then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
rPdC (regular priced dryer cycle time) is not available in washer.
SPdC (special priced dryer cycle time) is not available in washer.
Note
When setting up a special price period, the ending time must be later than the beginning time.
Note
32
Part 5 PROGRAMMING MODE -
Setup Mode
1155
Washing time set up
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous wash time.
Press COLORS(+) or DELICATES(-) button to select wash
time. (Maximum 15 minutes, Minimum 5 minutes.)
Press the START button.
The machine sets up the wash time, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
33
Part 5 PROGRAMMING MODE -
Setup Mode
1166
Rinsing times per cycle
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous rinsing times per cycle.
Press COLORS(+) or DELICATES(-) button to select rinsing
times per cycle.( Max 5, Min 1)
Press the START button.
The machine sets up the rinsing times per cycle, then
advances to the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
34
Part 5 PROGRAMMING MODE -
Setup Mode
1177
Rinsing time setup
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous rinsing time.
Press COLORS(+) or DELICATES(-) button to select rinse
cycle.( Max 15min, Min 8min)
Press the START button.
The machine sets up the rinsing time, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
35
Part 5 PROGRAMMING MODE -
Setup Mode
1188
Top spin speed – final spin time depends on RPM
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous top spin speed.
Press COLORS(+) or DELICATES(-) button to select top spin
speed. (0~4)
Press the START button.
The machine sets up the top spin speed, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
Top spin speed
0: 1150rpm
1: 900 rpm
2: 800 rpm
3: 600 rpm
4: 400 rpm
If you select 800 or below, the final spin time will be reduced by 9minutes
If you select 1000 ,900 rpm , the final spin time is fixed by 13 minutes
Note
36
Part 5 PROGRAMMING MODE -
Setup Mode
1199
Value of coin 2
Entering set up mode.
You will see LqC1
Press the WHITES button
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous Coin 2 value.
Press COLORS(+) or DELICATES(-) button to select value of
coin 2. (The value can be set from 0 to 9.95 in 5¢ increments.)
Press the START button.
The machine sets up the value of Coin 2, then advances to
the next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
Coin 2 is available for E-suds system
Note
37
Part 5 PROGRAMMING MODE -
Setup Mode
2200
Penny increment pricing offset
This represents the cent increment price offset used when debit card is setup.
Entering set up mode.
You will see LqC1
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Display previous penny increment pricing offset.
Press COLORS(+) or DELICATES(-) button to select value of
PIPo. (0~4)
Press the START button.
The machine sets up the value of PIPo, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
• Penny Increment Pricing Offset is available only in card type.
(It hasn’t affected on the coin type’s price setting.)
(top off time) is not available in washer.
Note
38
Part 5 PROGRAMMING MODE -
Setup Mode
2211
How to change the water level
You can change the water level by selecting two options.
1.LO indicate water level 23.7 [KHz]
2.HI indicate water level 23.5 [KHz]
Entering set up mode.
You will see LqC1
Button Display
• This function is only controlled in machine.
(It is not applied in setup card.)
Note
Press the WHITES button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press COLORS or DELICATES button and then select
Press COLORS(+) or DELICATES(-) button to select value of
PIPo. (0~4)
Press the START button.
The machine sets up the value of PIPo, then advances to the
next process automatically.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
One or the other will
display.
or
23.8 [KHz] 23.5 [KHz]
Part 5 PROGRAMMING MODE -
Test Mode
Diagnostic tests: (display)
This program has been added for testing the washer and detecting errors.
Entering the test mode
Data Name
Button Display Description
1. Entering programming mode
Entering
the test mode
2. WHITES
3. START
11
According to pressing START button, test move to the next step.
Number of times the
START button is pressed
None
1time
2 times
3 times
4 times
5 times
6 times
7 times
8 times
9 times
10 times
11 times
12 times
13 times
14 times
15 times
16 times
Turns on all lamps and locks the door
Tumble Clockwise.
Low Speed Spin
High Speed Spin
Inlet valve for main water turns on.
Inlet valve for hot wash turns on.
Inlet valve for softener turns on.
Inlet valve for bleach turns on.
Tumble counter clockwise.
Drain Pump turns on.
Turn on Circulation Pump.
Turns on all lamps.
Button Checks.
High Speed Spin
Check Point
PDA Signal Check
Insert service card (card type), turn on/off toggle switch (Coin
type).
Press the WHITES button. Then appears in the display.
Enter the diagnostic test mode.
Display
Displayed gc XX and US XX alternately
(Version)
rpm (40~50)
rpm (600)
rpm (1000~1100)
Water level frequency (261~)
Water level frequency (261~)
Water level frequency (261~)
Water level frequency (261~)
rpm (40~50)
Water level frequency (261~)
Displayed 0XX
Displayed gc XX and US XX alternately
Displayed gc XX and US XX alternately
rpm(1100)
this function is not applied in this machine
Note
Make sure the drum is empty when a diagnostic test is performed. Do not use .
39
40
Part 5 PROGRAMMING MODE -
Test Mode
22
Factory reset - EEPt
After factory reset, machine information is changed to the default value.
Entering set up mode.
You will see LqC1
Press the COLORS or the DELICATES
Button until appears in the display.
Press the START button.
Press the COLORS button until appears in the
display.
Press the START button, then factory reset is done.
is displayed.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
• Washing time 10 minutes
• Rinse cycle twice
• Top spin speed 1,150 RPM
• Add SUPER WASH 3 minutes extra wash and one extra rinse
Note
41
Part 5 PROGRAMMING MODE -
Test Mode
33
Time set up
Entering set up mode.
You will see LqC1
Press the COLORS or the DELICATES button until
appears in the display.
Press the START button.
The display will cycle through 2000 --> 0101 --> Sat --> 0000
repeatedly.
Press the START button.
Press COLORS(+) or DELICATES(-) button to select year
between 2000 and 2099.
Press the START button.
The machine sets up the year, then advances to the next
process automatically.
Press COLORS(+) or DELICATES(-) button to select a month
between 01 and 12.
Press the START button.
The machine sets up the month, then advances to the next
process automatically.
Press COLORS(+) or DELICATES(-) button to select the day
between 01 and 31.
Press the START button.
The machine sets up the day, then advances to the next
process automatically.
Press COLORS(+) or DELICATES(-) button to select the hour
between 00 and 23.
Press the START button.
The machine sets up the hour, then advances to the next
process automatically.
Press COLORS(+) or DELICATES(-) button to select minute
between 00 and 59.
Press the START button.
The machine sets up the minute.
1. Continue to set up the next mode.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
Button Display
42
Part 5 PROGRAMMING MODE -
Test Mode
44
Courtesy cycle
A courtesy cycle is like a complimentary cycle given to the customer when the washer goes out of order after the
customer has made the payment to wash clothes.
Entering set up mode.
You will see LqC1
Press the COLORS or the DELICATES
Button until appears in the Display.
Press the START button.
Press the COLORS button until appears in the
display.
Press the START button.
Display will show
.
Select the cycle you desire.
❋ Default WHITES course selected.
Press the START button.
Display will show the remaining time and start.
Button Display
43
Part 5 PROGRAMMING MODE -
Test Mode
55
Cycle Kill
■ Coin type
Opening
the seervice door.
You will see
Press the COLORS or the DELICATES
button until appears in the display.
Press the START button.
Press the COLORS button until appears in the
display.
Press the START button.
Start drain and display spin time.
End drain and display
.
Display with beeping.
Go back to ready mode.
Display spin time
Button Display
■ Card type
Insert
Service card.
Display spin time.
Begin to drain.
Display with beeping.
Remove service card.
Go back to ready mode.
Spin Time
Spin Time
Description Display
Part 5 PROGRAMMING MODE -
11
Collect information data : CLCt(display)
Collect Mode
The washer collects the usage data so that the owner can check various information like number of various cycles used,
how many times card or coins used, etc.
Entering the collect mode
Data Name
1.Entering the programming mode.
Entering
the collect
mode
❖ Check the collect information reference to the follow lists. The Lists are displayed by abbreviations.
2.Whites
3.Colors(+), Delicates(-)
4.Start
5.Colors(+), Delicates(-)
6.Start
7. Whites
Button Display Description
Insert service card(card type), turn on/off toggle switch (Coin
type).
Press the whites button until "tESt" appears in the display.
Press the Colors(+),Delicates(-) button until "CLCt" appears in
the display.
Enter the Collect information data.
xxxx
xxxx
CLCt
Move to each data list that you want to check by pressing with
Colors (+) or Delicates (-) button.
Display the value of selected data list
Move to upper level or Comes back to Idle State
44
45
Part 5 PROGRAMMING MODE -
Collect Mode
❊ Interval Cycles('Interval' means 'Since last data collecting')
❊ Accumulated Cycles('Accumulated'means 'Total cycles in washer/dryer's life time not include service cycles or trouble cycles')
❊ Authorized: Service Door Openings with PDA Communication (Open Service door Within 20 seconds After communicating with PDA)
❊ Unauthorized: Service Door Openings without PDA Communication
❊ These items (No.30~33) are not applied this program
Abbreviation Meaning Description
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
rgPr
rgCP
rgrP
rgHP
dELC
ItrC
ItCC
ItAC
ItHC
ItSC
IttF
ItUC
ItFC
ACrC
ACCC
ACAC
ACHC
ACSC
ACtF
ACUC
ACFC
ACrt
Itnr
Ittb
ItPd
Itdd
ItAd
ItUC
ItAC
tLdo
tLCo
tPdo
tPCo
SCPr
toPr
Regular Price
Regular Cold Price
Regular Warm Price
Regular Hot Price
Dryer Moisture Sense
Interval Regular Cycles
Interval Regular Cold Cycles (Delicates)
Interval Regular Warm Cycles (Colors, Perm Press)
Interval Regular Hot Cycles (Whites)
Interval Super Cycles
Interval Topoff Cycles
Interval Service Cycles
Interval Token Cycles
Accumulated Regular Cycles
Accumulated Regular Cold Cycles (Delicates)
Accumulated Regular Warm Cycles (Colors, Perm Press)
Accumulated Regular Hot Cycles (Whites)
Accumulated Super Cycles
Accumulated Topoff Cycles
Accumulated Service Cycles
Accumulated Token Cycles
Accumulated Run Time
Interval No Runs
Interval Trouble Cycles
Interval Power Downs
Interval Unauthorized Service Door Openings
Interval Authorized Service Door Openings
Interval Unauthorized Coin Vault Openings
Interval Authorized Coin Vault Openings
Time of Last Service Door Opening
Time of Last Coin Vault Opening
Time of Previous Service Door Opening
Time of Previous Coin Vault Opening
Super Cycle Price
Top Off Price
0~199 nickels ($.00~$9.95)
0~199 nickels ($.00~$9.95)
0~199 nickels ($.00~$9.95)
0~199 nickels ($.00~$9.95)
0: disable 1: enable
Number of Regular cycles ( 0~65535 )
Number of Regular Cold cycles ( 0~65535 )
Number of Regular Warm cycles ( 0~65535 )
Number of Regular Hot cycles ( 0~65535 )
Number of Super cycles ( 0~65535 ) ( Washer Only)
Number of Topoff cycles ( 0~65535 ) (Dryer Only)
Number of Service cycles (0~65535)
Number of Token cycles (0~65535)
Number of Regular cycles ( 0~65535 )
Number of Regular Cold cycles ( 0~65535 )
Number of Regular Warm cycles ( 0~65535 )
Number of Regular Hot cycles ( 0~65535 )
Number of Super cycles ( 0~65535 ) (Washer Only)
Number of Topoff cycles ( 0~65535 ) (Dryer Only)
Number of Service cycles ( 0~65535 )
Number of Token cycles (0~65535)
Number of Running minutes ( 0~65535 )
Money inserted, but no run
No money, but ran
Number of power down
Number of Unauthorized Service Door Openings ( 0~ 255)
Number of Authorized Service Door Openings ( 0~255)
Number of Authorized Service Door Openings ( 0~255)
Number of Authorized Coin Vault Openings (0~255)
tLdo is not available in washyer.(It can’t enter.)
tLCo is not available in washyer.(It can’t enter.)
tPdo is not available in washyer.(It can’t enter.)
tPCo is not available in washyer.(It can’t enter.)
0~199 nickels ($.00~$9.95)
0~199 nichels ($.00~$9.95)
No.
■ Collect Mode Data lists
46
Part 6 ERROR MODE
• Water supply is not adequate in
area.
• Water supply taps are not
completely open.
• Water inlet hose is bent.
• The filter of the inlet hose clogged.
• Drain hose is bent
or clogged.
• The drain filter is clogged.
• Load is too small.
• Load is out of balance.
• The appliance has an imbalance
detection and correction system. If
individual heavy articles are loaded
(bath mat, bath robe, etc.) and the
imbalance is too great, after several
attempts to restart the spin cycle the
machine will stop and the error code
will be displayed.
• Is the door opened or not
completely closed?
• The water overfills due to a faulty
water valve.
• The water level sensor
malfunction.
• Overload in motor.
• Disconnection of card reader wire.
Check another tap in the house.
Fully open tap.
Straighten hose.
Check the filter of the inlet hose.
Clean and straighten the drain hose.
Clean the drain filter.
Add 1 or 2 similar items to help
balance the load.
Rearrange load to allow proper
spinning.
Close the door completely.
If it will not open, call for service.
Close the water tap.
Unplug the power plug.
Call for service.
Restart the cycle after 30 minutes. If LE is
not released, call for service.
Check the card reader wire.
Problem Possible Cause Solution
■ Meaning of Error Codes that LED displays during occurrence of problem.
47
Part 7 POWER FAIL RECOVERY
In case of power failure, the machine stops running but the time display remains on, showing the time just before
power failure.
Part 8 DEFAULT WASHER SETTINGS
Default Settings
Wash Time (Minutes)
Rinse Time (Minutes)
Spin Time (Minutes)
Rinsing times
Coin #1 Value
Coin #2 Value (E-suds)
Vend Price
Add super wash price
Top Spin speed
Default
10 Minutes
16 Minutes
13 Minutes
Twice
25¢
25¢
$1.00
25¢
1150 rpm
48
Part 9 WARRANTY
LG ELECTRONICS, INC.
LG COMMERCIAL WASHING MACHINE LIMITED WARRANTY - USA
Should any part in your LG Commercial Washing Machine fails due to a defect in material or workmanship under normal use, during
the warranty period set forth below, LG will provide a replacement part. This limited warranty is valid only to original retail purchase of
the product and applies only when used within the United States, excluding U.S. Territories. Proof of original retail purchase date is
required to obtain a replacement part under this limited warranty.
* OPL (On Premise Laundry), defined as non-vended commercial products used in locations such as hotels, hospitals,
health clubs, businesses, etc. will have one (1) full year parts only warranty. Labor and transportation are NOT included.
✪ Replacement products and parts are warranted for the remaining portion of the original warranty period.
✪ Replacement products and parts may be new or remanufactured.
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION,
ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED
WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE.
NEITHER THE MANUFACTURER NOR ITS U.S. DISTRIBUTOR SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL,
INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR
PROFITS, OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE.
Some states do not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an
implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights
and you may also have other rights that vary from state to state.
THIS LIMITED WARRANTY DOES NOT APPLY TO:
1. Service trips to deliver, pick up, install of the product, instruct or replace house fuses, connect house wiring or plumbing, or correction of
unauthorized repairs, or to service the product if your product is located in a remote area (Standard Remote zones) where service by an
authorized LG service provider is not available.
2. Failure of product to perform during power failures and interruptions or inadequate electrical service.
3. Damage caused by leaky or broken water pipes, frozen water pipes, restricted drain lines, inadequate or interrupted water supply or
inadequate supply of air.
4. Damage resulting from running the product in a corrosive atmosphere or contrary to the instructions outlined in the product owner’s manual.
5. Damage to the product caused by accidents, pest and vermin, lightning, wind, fire, floods, or acts of God.
6. Damage resulting from misuse, abuse, improper installation, repair, or maintenance. Improper repair include use of parts not approved or
specified by LG.
7. Damage or failure caused by unauthorized modification or alteration, or if it is used for other than intended purpose.
8. Damage or failure caused by incorrect electrical current ,voltage or plumbing codes, or use of accessories, components or consumable
cleaning products that are not approved by LG.
9. Damage caused by transportation and handling, including scratches, dents, chips, and/or other damage to the finish of your product, unless
such damage results from defects in materials or workmanship and is reported within one (1) week of delivery.
10. Damage to any display, open box, discounted, or refurbished product.
11. Products with original serial numbers that have been removed, altered or can not be readily determined.
12. Increases in utility costs and additional utility expenses.
13. The removal and reinstallation of the Product if it is installed in an inaccessible location or is not installed in accordance with published
installation instructions.
14. Repair or replacement of light bulbs, filters or any consumable parts. The cost of repair or replacement under these excluded circumstances
shall be borne by the consumer.
WARRANTY PERIOD (Please see OPL* below): PARTS ONLY, not Labor and transportation included.
Note: If the original date of retail purchase can not be verified, the warranty will begin 60 days from the date of
manufacture.
TWO (2)
YEARS from the date of
original retail purchase
All parts. Electronic controls: Main control
board and user interface board.
In addition, the following cabinet
parts are warranted against rust
through: top plate, cabinet, base and
door.
Direct Drive motor, bearing, seal,
shaft, inner drum and outer tub
THREE (3) YEARS from the date of
original retail purchase
FIVE (5) YEARS from the date of
original retail purchase
MEMO
49
MEMO
50
MEMO
51
Loading...