LG FH069FD4P Owner’s Manual

OWNER’S MANUAL

COMMERCIAL WASHER

Before beginning installation, read these instructions carefully. This will simplify installation and ensure that the washer is installed correctly and safely. Leave these instructions near the washer after installation for future reference.

MODEL FH069FDP/FH069FD4P/FH069FD6P/FH069FD7P

MFL67658534

www.lg.com

PRODUCT FEATURES

DIRECT DRIVE SYSTEM

The advanced brushless DC motor drives the drum directly without using a belt and pulley.

TILTED DRUM AND EXTRA LARGE DOOR OPENING

The tilted drum and extra large opening make it possible to load and unload clothing more easily.

ULTRA CAPACITY

The larger drum enables more tumbling action and greater centrifugal force, but also less tangling and wrinkling of the laundry. Heavier loads, such as king size comforters, blankets, and curtains can be washed.

SEE-THROUGH DOOR AND BIG DOOR

You can see the laundry throughout the cycle.

MAGNETIC DOOR PLUNGER

Safely and conveniently secure the door slightly ajar with the magnetic door plunger. This will promote air circulation and allow the interior of the machine to dry. To use this feature, after the load has been removed, do not close the door completely. When the magnetic door plunger comes into contact with the metal washer cabinet, it will secure the door slightly open allowing the interior of the washer to dry.

STAINLESS STEEL DRUM

Stainless steel drum offers extreme durability.

TUB CLEAN

Regular cleaning of the tub on a monthly basis using TUB CLEAN can help keep the tub clean and fresh.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.

Your Safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word DANGER, WARNING or CAUTION. These words mean:

DANGER

You will be killed or seriously injured if you don’t immediately follow instructions.

WARNING

You can be killed or seriously injured if you don’t follow instructions.

CAUTION

You may be slightly injured or cause damage to the product if you do not follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

Disposal of your old appliance

1. This crossed-out wheeled bin symbol indicates that waste electrical and electronic products (WEEE) should be disposed of separately from the municipal waste stream.

2. Old electrical products can contain hazardous substances so correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

Your old appliance may contain reusable parts that could be used to

repair other products, and other valuable materials that can be recycled to conserve limited resources.

3. You can take your appliance either to the shop where you purchased the product, or contact your local government waste office for details of your nearest authorised WEEE collection point. For the most up to date information for your country please see www.lg.com/global/ recycling

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.

BASIC SAFETY PRECAUTIONS

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following.

•

Read all instructions before using the washer.

•

Do not wash articles that have been previously

cleaned in, washed in, soaked in, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.

•

Do not add gasoline, dry cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

•

Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the washing machine, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

•

Do not allow children to play on or in the washer.

Close supervision of children is necessary when the washer is used near children.

•

Before the washer is removed from service or

discarded, remove the door to prevent children from hiding inside.

• Do not install or store the washer where it will be

exposed to the weather.

• Do not tamper with the controls.

• Do not repair or replace any part of the washer

or attempt any servicing unless specifically recommended in the user-maintenance instructions or published user-repair instructions that you understand and have the skills to carry out.

• See Installation Instructions for grounding

requirements.

• ALWAYS follow the fabric care instructions supplied

by the garment manufacturer.

• Do not place items exposed to cooking oil in your

washer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

• Do not use fabric softeners or products to eliminate

static unless recommended by the manufacturer of the fabric softener or product.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

• Do not use an adapter or extension cord.

• Do not remove ground prong.

• If you don’t have the proper outlet, consult an electrician.

WARNING

Improper connection of the equipment-grounding conductor can result in risk of electric shock. Consult a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a proper outlet installed by a qualified electrician.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.

SAFETY INSTRUCTIONS FOR INSTALLATION

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following.

•

Refer to INSTALLATION INSTRUCTIONS for detailed grounding procedures.

instructions are packed in the washer for installer's reference. If the washer is moved to a new location, have it checked and reinstalled by a qualified service person. Failure to follow this warning can cause serious injury, fire, electric shock or death.

•

Do not, under any circumstances cut or remove the third (ground) prong from the power cord.

to follow this warning can cause serious injury, fire, electric shock or death.

•

For personal safety, this appliance must be properly grounded.

serious injury, fire, electric shock or death.

•

The power cord of this appliance is equipped with a 3-prong (grounding) plug which fits a standard 3-prong (grounding) wall outlet to

possibillty of electric shock hazard from this appliance.

•

This washer must be plugged into a 220-240 V~, 50 Hz grounded outlet.

can cause serious injury, fire, electric shock, or death.

•

Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.

Failure to follow this warning can cause serious injury, fire, electric shock, or death.

•

Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

Failure to follow this warning can cause serious injury, fire, electric shock, or death.

•

Do not install on carpet. Install the washer on a solid floor.

serious leak damage.

•

Do not remove the ground prong. Do not use an adapter or extension cord. Plug into a grounded 3 prong outlet.

cause serious injury, fire, electric shock, or death.

Failure to follow this warning can cause

Installation

Failure

minimize the

Failure to follow this warning

Failure to follow this warning can

•

The washer should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

•

Never unplug your washer by pulling on the power cord. Always grip the plug firmly and pull straight out from the outlet.

cause serious injury, fire, electric shock, or death.

•

Repair or replace all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

can cause serious injury, fire, electric shock,or death.

•

When installing or moving the washer, be careful

not to pinch, crush, or damage the power cord.

Failure to follow this warning can cause serious injury, fire, electric shock, or death.

•

The washer must be installed and electrically grounded by a qualified service person in accordance with local codes,

hazard and assure stability during operation.

•

The washer is heavy. Two or more people are needed to install and move the appliance.

do so can result in back or other injury

•

Store and install the washer where it will not

be exposed to temperatures below freezing or exposed to outdoor weather conditions.

follow this warning can cause serious leak damage.

•

Do not install the washer in humid spaces to reduce the risk of electric shock.

can cause serious injury, fire, electric shock, or death.

•

To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long sleeved gloves and safety glasses.

Failure to follow all of the safety warnings in this manual could result in property damage, injury to persons or death.

•

Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemicals, etc.

Failure to follow this warning can

Failure to do so can result in fire.

This provides the best

Failure to follow this warning

to prevent shock

Failure to

Failure to follow this warning

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.

SAFETY INSTRUCTIONS FOR USE, CARE, CLEANING, AND DISPOSAL

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:

•

Unplug the washer before cleaning

risk of electric shock.

•

Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer.

damage the finish.

•

Do not put oily or greasy rags or clothing on top of the washer.

vapors that could ignite the materials.

•

Do not wash items that are soiled with vegetable or cooking oil.

contain some oil after laundering. Due to the remaining oil, the fabric may smoke or catch fire by itself.

•

Disconnect this appliance from the power supply before attempting any user maintenance.

Turning the controls to the OFF position does not disconnect this appliance from the power supply. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

•

Do not combine laundry products for use in 1 load unless specified on the label. Do not mix chlorine bleach with ammonia or acids such as vinegar.

Follow package directions when using laundry products. Incorrect usage can produce poisonous gasresulting in serious injury or death.

•

Do not reach into the washer while parts are moving. Before loading, unloading, or adding items, push in the cycle selector knob and allow the drum to coast to a complete stop before reaching inside.

Failure to follow this warning can cause serious injury, fire, electric shock, or death.

to avoid the

They will

These substances give off

These items may

•

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.

•

Children should be supervised to ensure that they do not play with the appliance.

•

Do not allow children to play on or in the washer.

Close supervision of children is necessary when the washer is used near children. As children grow, teach them the proper, safe use of all appliances. Failure to comply with these warnings could result in serious personal injuries.

•

Destroy the carton, plastic bag, and other packing materials after the washer is unpacked.

Children might use them for play. Cartons covered with rugs, bedspreads or plastic sheets can become airtight chambers. Failure to comply with these warnings could result in serious personal injuries.

•

Keep laundry products out of children's reach.

To prevent injury to persons, observe all warnings on product labels. Failure to comply with these warnings could result in serious personal injuries.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.

SAFETY INSTRUCTIONS FOR USE, CARE, CLEANING, AND DISPOSAL

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:

•

Remove the door to the washing compartment to avoid the danger of children or small animals getting trapped inside before your washer is removed from service or discarded.

do so can result injury or death.

•

Before the washer is removed from service or discarded, remove the washer door to prevent accidental entrapment.

Failure to comply with these warnings could result in serious personal injuries.

•

If the supply cord is damaged, it must be replaced by the

Failure to

manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.

•

The new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused.

TABLE OF CONTENTS

2 PRODUCT FEATURES

IMPORTANT SAFETY INSTRUCTIONS

4 BASIC SAFETY PRECAUTIONS 4 GROUNDING INSTRUCTIONS 5

SAFETY INSTRUCTIONS FOR INSTALLATION

6 SAFETY INSTRUCTIONS FOR USE,

CARE, CLEANING, AND DISPOSAL

PARTS AND ACCESSORIES

9 Parts 9 Accessories

CONTROL PANEL FEATURES

10 Coin type 10 Card type / OPL type

INSTALLATION INSTRUCTIONS

12 Checking and choosing the proper location 13 Unpacking and removing shipping bolts 14 Connecting the water lines 15 Connecting the drain line 16 Leveling the washing machine

17 PREPARATION

Precautions for fabric care before wash cycle

18 Fabric care labels 18 Sorting laundry 19 Recommended detergent 19 About the dispenser 20 Loading the dispenser

21 OPERATING YOUR WASHER

22 PROGRAMMING MODE

23 Structure of Programming mode

– Card/Coin type

Structure of Programming mode – OPL type

25 PROGRAMMING MODE –SETUP MODE 25 - 1. How to change regular price. 26 - 2. How to change regular delicates price. 27 - 3. How to change regular warm & cold

28 - 4. How to change regular hot price 29 - 5. How to change special price 30 - 6. How to change special delicates price 31 - 7. 32 - 8. How to change special hot price 33 - 9. How to change add super wash price 34 - 10. How to change add super wash type 35 - 11. How to enter the 36 - 11-1. Special price day setup 37 - 11-2. Non-stop rinse

price

How to change special warm & cold price

38 - 11-3. Add super wash setup 39 - 11-4. Vend type setup - card type or coin

40 - 11-5. Pre-wash setup 41 - 11-6. Twin spray setup 42 - 12. How to enter the 43 - 12-1. Pause function setup 44 - 13. How to enter the special price day 45 - 13-1. How to change to Sunday 46 - 14. Special price beginning time setup 47 - 15. Special price ending time setup 48 - 16. Washing time setup 49 - 17. Rinsing time per cycle 50 - 18. Rinsing time setup 51 - 19. Top spin speed – final spin time

52 - 20. Value of coin 1 53 - 21. Value of coin 2 54 - 22. Penny increment pricing offset 55 - 23. How to change the water level 56 - 24. Beep volume 57 - 25. Time to keep the coin (Use only for

58 - 26. How to set drop count 59 - 27. How to set rinse spin enable 60 - 28. How to enter the 61 - 29. How to set custom program 62 PROGRAMMING MODE – TEST MODE 62 - 1. 63 - 2. Factory reset - 64 - 3. Time setup 65 - 4. Courtesy cycle 66 - 5. Cycle Kill 67 - 6. Password - 68 - 7. Tub clean - 69 70 Collect Mode Data lists

type setup

depends on RPM

coin type)

PROGRAMMING MODE – COLLECT MODE

71 MAINTENANCE

71 - Care after wash 71 - Storing the Washer 71 - Cleaning the Dispenser 72 - Cleaning the water inlet filters 73 - Cleaning the drain pump filter 74 - Cleaning the door seal 74 - Clean the drum, TUB CLEAN

75 ERROR MODE

76 POWER FAIL RECOVERY

76 DEFAULT WASHER SETTINGS

77 SPECIFICATIONS

PARTS AND ACCESSORIES

Parts

PARTS AND ACCESSORIES

Detergent

dispenser

(for single

model)

Door

Magnet Door

Plunger

(see page 2)

Accessories

Hot and Cold

Water Hoses

Drain pump filter cover Drain pump filter Drain hose

Detergent dispenser drawer (for stack model)

Control panel

Door seal

Tub

Leveling feet

Non-skid pads

Water

inlets

Shipping

bolts

Power cord

Drain hose

Caps (4)

(for covering shipping bolt holes)

Wrench

(for removing

shipping bolts and

adjusting leveling feet)

Tie Strap

(for securing drain hose)

Elbow Bracket

(for securing drain hose)

OPL sheet

(only for OPL type)

CONTROL PANEL FEATURES

1 25

4 3

1 25

4 3

1 25

4 3

1 25

4 3

1 25

4 3

CONTROL PANEL FEATURES

Coin type - Side by side (FH069FD4P)

Coin type - Stack (FH069FDP)

Card / OPL Type (FH069FD6P, FH069FD7P)

1. Display LED

2. Cycle button

3. Optional function button

4. Start/Pause button

5. Status LED

CONTROL PANEL FEATURES

Display LEDStatus LED Cycle button

Display LED

The display shows the vend price and remaining time and programming options. Error

codes are also displayed here.

Cycle button

Press the CYCLE button to select the desired cycle based on laundry types and conditions.

Hot

Use for hot washing for heavy fabrics, such as white clothes, table linens, and heavily soiled clothes.

Warm

Use for warm washing for heavy fabrics, such as jeans, corduroys, or work clothes.

Cold

Use for cold washing for sturdy fabrics, such as casual work.

Delicates

Use for cold washing for synthetic fabrics, such as washable knit fabric and no-iron finishes.

Start/Pause button

Optional function button

Wash time or rinse cycle can be added when additional coin is inserted or a valid cash card is entered.

Start/Pause button

The START LED flashes when the full vend price has been satisfied and the cycle has been chosen.

Status LED

LED Description

LED flashes whenever the washing cycle is in operation.

LED flashes whenever the Rinsing cycle is in operation.

LED flashes whenever the Spining cycle is in operation.

LED flashes whenever the door lock is activated.

INSTALLATION INSTRUCTIONS

Checking and choosing the proper location

Install the washing machine on a solid floor that is strong and rigid enough to support the weight of the washing machine, even when fully loaded, without flexing or bouncing. If the floor has too much flex, you may need to reinforce it to make it more rigid. If the floor is not solid, it may cause severe vibration and noise.

Clean the floor before installation.

- Make sure to select solid and smooth ground.

Two or more people are needed for moving

and unpacking the washing machine.

Allow for sufficient space between the walls

and the washing machine for installation.

Space requirements

You must allow sufficient space for water lines, the drain line, and airflow.

NOTE

• Be sure to allow for wall, door, or floor

moldings that may increase the required clearances.

Installing on a floor

/4”

(570mm)

/16”

(983mm)

1”

(25mm)

/16”

(767mm)

/8”

(1337mm)

27”

(686mm)1”(25mm)

4”

(100mm)

NOTE

• The floor must be strong and rigid enough to support the weight of the washer, when fully loaded, without flexing or bouncing. If your floor has too much flex, you may need to reinforce it to make it more rigid. A floor that is adequate for a top-loading washer may not be rigid enough for a front loading washer, due to the difference in the spin speed and direction. If the floor is not solid, your washer may vibrate and you may hear and feel the vibration throughout your house.

• Before installing the washer, make sure

the floor is clean, dry and free of dust, dirt, water and oils so the washer feet can not slide easily. Leveling feet that can move or slide on the floor can contribute to excess vibration and noise due to poor contact with the floor.

Unpacking and removing shipping bolts

When removing the washer from the carton base, be sure to remove the foam drum support in the middle of the carton base. If you must lay the washer down to remove the base packaging materials, always lay it carefully on its side. DO NOT lay the washer on its front or back.

Foam Tub Support Carton Base

INSTALLATION INSTRUCTIONS

Remove the bottom two shipping bolts

with the wrench (included) to fully loosen all four shipping bolts by turning them counterclockwise and then pulling them out.

Retainer

Shipping

bolt

Locate the four hole caps included in the

accessory pack and install them in the shipping bolt holes.

Cap

NOTE

• Save the bolt assemblies for future use. To

prevent damage to internal components, DO NOT transport the washer without reinstalling the shipping bolts.

• Failure to remove shipping bolts and retain ers may cause severe vibration and noise, which can lead to permanent damage to the washer. The cord is secured to the back of the washer with a shipping bolt to help prevent operation with shipping bolts in place.

INSTALLATION INSTRUCTIONS

Connecting the water lines

Check the rubber seals on both sides of the

hose.

- Insert a rubber seal into the threaded fittings on each hose to prevent leaking.

Rubber seal

Connect the hoses to the water inlets tightly

by hand and then tighten another 2/3 turn with pliers.

- Connect the blue hose to the cold water inlet and the red hose to the hot water inlet.

Water hose

Water hose (To water inlet on the washing machine)

Connect the water supply hoses to the HOT

and COLD water faucets tightly by hand and then tighten another 2/3 turn with pliers.

- Connect the blue hose to a cold water faucet and the red hose to a hot water faucet.

(To faucet)

WARNING

• Do not overtighten. Damage to the cou-

pling can result.

After connecting inlet hose to water faucets,

turn on the water faucets to flush out foreign substances (dirt, sand or sawdust) in the water lines. Let water drain into a bucket, and check the water temperature.

Cold water

inlet

Hot water inlet

WARNING

• Do not overtighten the hoses.

Overtightening can damage the valves resulting in leaking and property damage.

Check for leaks by turning on the faucets.

- If water leaks, check steps 1 to 4 again.

NOTE

• For your safety, and for extended product

life, use only authorized components. The manufacturer is not responsible for product malfunction or accidents caused by the use of separately purchased unauthorized parts.

• Use new hoses when you install the

washing machine. Do not reuse old hoses. Use only the inlet hoses provided with the washer. LG does not recommend the use of aftermarket hoses.

• Periodically check the hoses for cracks,

leaks and wear, and replace the hoses every 5 years.

• Do not stretch the water hoses intentionally, and make sure that they are not crushed by other objects.

• Water supply pressure must be between

1.0 kgf/cm² and 8.0 kgf/cm² (0.1~0.8 MPa). If the water supply pressure is more than

8.0 kgf/cm², a pressure reducing valve must be installed.

• To provide optimum washing performance

the hot water temperature should be set at 120-135°F (48-57°C) and the cold at 60°F (15°C).

Connecting the drain line

INSTALLATION INSTRUCTIONS

Secure the drain hose in place to prevent moving and leaking.

NOTE

• The drain hose should be properly secured.

Failure to properly secure the drain hose can result in flooding and malfunction.

• Total height of the hose end should not

exceed 96 inches (244.8 cm) from the bottom of the washer.

• The drain must be installed in accordance

with any applicable local codes and regulations.

• Make sure that the water lines are not

stretched, pinched, crushed, or kinked.

Using a standpipe

Clip the end of the hose into the elbow

bracket.

- Connect the elbow bracket within 4 inches (10 cm) from the end of the drain hose. If the drain hose is extended more than 4 inches (10 cm) beyond the end of the elbow bracket, mold or microorganisms could spread to the inside of the washer.

No more than 4 inches (10 cm)

Elbow Bracket

Using a laundry tub

Clip the end of the hose into the elbow

bracket.

- Connect the elbow bracket within 4 inches (10 cm) from the end of the drain hose. If the drain hose is extended more than 4 inches (10 cm) beyond the end of the elbow bracket, mold, or microorganisms could spread to the inside of the washer.

No more than 4 inches (10 cm)

Elbow Bracket

Hang the end of the drain hose over the side

of the laundry tub.

Elbow

Bracket

Laundry Tub

max. 96”

(2.4 m)

max. 96”

(2.4 m)

Drain Hose

Tie Strap

Insert the end of the drain hose into the

standpipe.

Use a tie strap to secure the drain hose in

place.

Elbow Bracket

Drain Hose

Use a tie strap to secure the drain hose in

place.

INSTALLATION INSTRUCTIONS

Leveling the washing machine

The washer tub of your new washing machine spins at very high speeds. To minimize vibration, noise, and unwanted movement, the floor must be perfectly level and solid.

Check the washing machine’s level.

- Check the precise level by rocking the top edges of the washing machine or placing a level on the washing machine. The slope beneath the washing machine must not exceed 1°, and all four leveling feet must rest firmly on the floor.

Turn the lower leveling feet clockwise to

level the washing machine.

- Turning the lower leveling feet clockwise raises the washing machine.

Raise

Turn the locknuts counterclockwise and

tighten them when the washing machine is level.

Level

1°

Check the washing machine’s level again.

- Push or rock the top edges of the washing machine gently to make sure that the washing machine does not rock.

- If the washing machine rocks, repeat steps 1 to 3.

WARNING

• Using the washing machine without leveling, it may result in malfunction caused by the production of excess vibration and noise.

• Use the leveling feet only when you level the washing machine. If you raise the level-

ing feet unnecessarily, it may cause abnormal vibration of the washing machine.

Using non-skid pads (optional)

If you install the washing machine on a slippery surface, it may move because of excessive vibration. Incorrect leveling may cause malfunction through noise and vibration. In the event of this, lay the non-skid pads under the leveling feet and adjust the level.

1 Clean the floor to attach the non-skid pads.

- Use a dry rag to remove and clean foreign

objects or moisture. If moisture remains, the non-skid pads may slip.

Adjust the level after placing the washing

machine in the installation area.

Place the adhesive side of the non-skid pad

on the floor.

- It is most effective to install the non-skid

pads under the front legs. If it is hard to place the pads under the front legs, place them under the back legs.

This side up

Tighten all 4 lock

nuts securely using

the wrench.

Adhesive side

Remove backing

Check the washing machine’s level again.

- Push or rock the top edges of the washing

machine gently to make sure that the washing machine does not rock. If the washing machine rocks, level the washing machine again.

PREPARATION

Precautions for fabric care before wash cycle

Read and observe the following to prevent shrinkage or damage to clothes.

PREPARATION

Check all pockets to make sure that they are

empty.

- Items such as clips, matches, pens, coins, and keys can damage both your washer and your clothes.

Close zippers, hooks, and drawstrings

to prevent these items from snagging or tangling on other clothes.

Pretreat heavily stained areas before

washing.

- Doing so will produce clean, stain-free results.

Combine large and small items in a load.

Load large items first.

Large items should not be more than half of

the total washload.

The washer can be fully loaded, but the

drum should not be tightly packed with items.

- The door of the washer should close easily.

Do not wash single items, except for bulky

items such as blankets. Make sure to wash laundry in similar types of loads.

- Washing a single small item may result in the tub becoming unbalanced, vibrating, making a noise.

Brush heavy soil, dust, or hair off fabrics

before washing.

- Laundry may not wash clean if there is dirt or sand on the fabrics, or they may be damaged due to particles rubbing against sheer fabrics.

Wash blankets individually.

- Washing more than one blanket together may produce unclean results due to tangling or an unbalanced load.

Always separate fabrics according to their

colors and wash them separately to prevent colors from running.

- Fabrics may damage or become stained due to fabric dyes running or due to foreign objects transferring from one fabric to another.

Do not wash waterproof clothes.

- This may cause abnormal vibration or may cause the load to bounce, which could damage the tub.

Check if there are any other foreign objects

in the door seal and take extra care that clothes do not get caught there.

- Foreign objects in the door seal may stain clothes, and water may leak if clothes get caught in the door seal.

Wash underwear or small, light items in a

laundry net.

- Small, light items may get caught in the door seal, and a brassiere hook may damage other items or the tub.

PREPARATION

Fabric care labels

Most articles of clothing feature fabric care labels that include instructions for proper care.

Category Label Directions

Hand Wash

Machine Wash, Normal Cycle

Use Permanent Press/ Wrinkle Resistant washing machine setting (which has a cool down or cold spray before the reduced spin)

Washing

Use Gentle/Delicate washing machine setting (slow agitation and/ or reduced wash time).

Do Not Wash

Do Not Wring

Hot

Sorting laundry

It is recommended that you sort laundry into similar loads that are washable in the same cycle. Refer to the following chart for sorting clothes

Colors

Soil

Fabric

Lint

Whites / Lights / Darks

Heavy / Normal / Light

Delicates / Easy Care / Sturdy Cottons

Lint Producers / Lint Collectors

Water

Temperature

Bleach

symbols

Warm

Cold/Cool

Any Bleach (When Needed)

Only Non-Chlorine Bleach (When Needed)

Do Not Bleach

PREPARATION

Recommended detergent

Use HE (High-Efficiency) detergent for frontloading washing machines. HE detergents dissolve more efficiently and produce fewer suds to ensure efficient washing and rinsing. Use the correct amount of detergent as indicated on the label of the detergent packaging.

NOTE

• Use HE detergents, since using a regular

detergent will produce excessive suds.

• HE detergents produce fewer suds,

dissolve more efficiently to improve washing and rinsing performance, and help to keep the interior of your washer clean.

• Use less detergent for soft water.

• Wipe up any spills immediately, as liquids

could damage the finish and the control panel of the washing machine.

• Using too much detergent can cause

a build-up in the tub resulting in unsatisfactory performance and machine malfunction.

• If you use a detergent that does not

dissolve easily or a detergent with high viscosity, it will leave a residue on the tub, which may not rinse properly.

About the dispenser

The automatic dispenser consists of three compartments which hold:

• Liquid chlorine bleach.

• Liquid fabric softener.

• Liquid and powdered detergent and color-

safe bleach for main wash. All laundry products can be added at once in their respective dispenser compartments. They will be dispensed at the appropriate time for the most effective cleaning. After adding the laundry products to the dispenser, close the dispenser cover.

To add detergent, bleach, and fabric softener to the automatic dispenser:

1. Open the dispenser cover.

2. Load the laundry products into the

appropriate compartments.

3. Slowly close the dispenser cover to avoid

early dispensing of the laundry products.

NOTE

• It is normal for a small amount of water to

remain in the dispenser compartments at the end of the cycle.

PREPARATION

Loading the dispenser

Main Wash Detergent Compartment

This compartment holds laundry detergent for the main wash cycle, which is added to the load at the beginning of the cycle. Always use HE (High-Efficiency) detergent with your washing machine. Follow the detergent manufacturer's instructions with respect to the amount of detergent to use, and never use more than the recommended amount. Using too much detergent can result in detergent buildup in clothing and the washer. Either powdered or liquid detergent may be used.

NOTE

• Liquid or powdered color-safe bleach may

be added to the main wash compartment with detergent of the same type.

- Single model -

Main Wash

Detergent

Compartment

Liquid Chlorine

Bleach Compartment

- Stack model -

Main Wash Detergent

Compartment

Liquid Fabric

Softener Compartment

Liquid Bleach Compartment

This compartment holds liquid chlorine bleach, which will be dispensed automatically at the proper time during the wash cycle.

NOTE

• Do not add powdered or liquid color-safe

bleach to this compartment.

• Always follow the manufacturer’s recommendations when adding bleach. Do not exceed the maximum fill line. Using too much bleach can damage fabrics.

• Never pour undiluted liquid chlorine bleach

directly onto the load or into the drum. Fabric damage can occur.

Fabric Softener Compartment

This compartment holds liquid fabric softener, which will be automatically dispensed during the final rinse cycle.

NOTE

• Always follow the manufacturer’s recommendations when adding fabric softener. Do not exceed the maximum fill line. Using too much fabric softener may result in stained clothes.

• Dilute concentrated fabric softeners with

warm water. Do not exceed the maximum fill line.

• Never pour fabric softener directly onto

the load or into the drum.

• Do not add the fabric softener sheets to

this compartment.

• Do not add ‘fabric sheet softener’ into

the dispenser draw as it is likely to cause

water to leak out. If ‘ fabric sheet softener’

has been added, please pull out the dispenser draw and remove.

Liquid Chlorine

Bleach Compartment

Liquid Fabric

Softener Compartment

OPERATING YOUR WASHER

1. Ready mode

1) Coin / Card type

– The cycle LEDs are lit at the same

time, when the prices of cycles are equal.

2) OPL type

– The cycle LEDs flash at the same time,

and displays PUSH.

NOTE

• Price setting varies by country

• Set your country from

(Refer

How to enter the

• After EEPT, reset your country (Default

country is EUK)

Insert card/coin (not for OPL type)

Insert a cash card that has a sufficient balance.

The card balance should be more than the programmed vend price for a selected cycle.

mode

)

NOTE

• When the card balance is not enough,

machine displays the card balance for 5 seconds and then displays sage repetitively

• Insert a sufficient amount of change that

is more than the programmed vend price for the selected cycle.

mes-

NOTE

• The machine will not start until sufficient

coins are inserted.

3. Select the cycle

Press the desired button and press the

Start button. The display LED will show the remaining time and the selected cycle starts.

• Select cycles designed for different types of

fabric and soil levels.

CYCLE Fabric type

Hot

Warm

Cold

Delicates

Cotton, linen, towels, shirts, sheets

Cotton, mixed loads, work clothes, jeans, shirts

Cotton, dress shirts, pants, wrinkle-free clothing, cotton/ poly blend clothing, tablecloths

Dress shirts, blouses, nylons, sheer or lacey garments

Wash/Rinse

Temp.

Hot / Cold

Warm / Cold

Cold / Cold

4. Add super wash

Wash time or rinse cycle can be added

when additional coin is inserted or a valid cash card is entered.

5. Change course

You cannot change the cycle while the

machine is running.

6. Cycle finish

The machine stops and LED display shows

with beeper sound.

Do not work any button and stop the washer

❋

(When the washer is operating) or (when a cycle is in progress)

WARNING

• To reduce the risk of fire, electric shock, or

injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.

PROGRAMMING MODE

: You can check machine information or change setting on Program setup, Collect Information Data,

Diagnostic Test. There are two methods that you can enter programming mode.

How to enter Programming mode

You can enter programming mode only for Idle state and pause state.

- Card Type

1) Insert service card.

2) Display will show .

- Coin Type

1) Dissemble upper coin box key.

2) Take out the coin drop from the coin box.

3) Turn on/off the toggle switch at the back of the coin box.

4) Display will show .

- All Types

1) Push the Hot & Cold button at the same time.

2) Push the Warm button 3 times.

3) Push the Start button.

4) Display will show .

Coin Vault Openings close

Coin Box Key

Insert Debit Card

How to use button

You can change Washer vend price, cycle time and Cycle parameters, etc.

Press Button Description

Hot

Warm

Cold

Start Enters the selected mode

Moves to upper level or

Comes back to Idle State

Moves through modes in the

same level (+)

Moves through modes in the

same level (-)

- coin type - - card type - - OPL type -

NOTE

• If you turn on the power without connecting meter case for the first time, the machine display

• When the machine is shipped from the factory, it is set in the coin type. You can change Card/

• The machine will display PUSH for OPL type

• Price setting varies by country

• Set your countr y from mode (Refer

• After EEPT, reset your country (Default country is EUK)

Coin type by button. (For more information refer to SETUP mode.)

How to enter the

)

PROGRAMMING MODE

Structure of Programming mode – Card / Coin type

Algorithm flow chart shows how to control the programming mode.

Before program set, check the structure of the programming mode.

1. Turn on/off toggle switch or insert service card, for entering setup mode (or follow OPL type instructions).

2. Press Hot button to move to the upper level.

3. Press Warm (+) or Cold (-) button if you want to be at the same level.

4. Press Start button to enter the details of Setup or Diagnostic Tests.

is to set price value, time value, vend type, etc. consists of line test, reset, free cycle, and kill cycle. is to collect the usage data.

NOTE

• Do not use , .

• It is used only in inspecting the machine.

• Price setting varies by country

• Set your countr y from mode (Refer

• After EEPT, reset your country (Default country is EUK)

How to enter the

)

PROGRAMMING MODE

Structure of Programming mode – OPL type

Algorithm flow chart shows how to control the programming mode. Before program set, check the structure of the programming mode.

The method of entering setup mode.

1) Push the Hot & Cold button at the same time.

2) Push the Warm button 3 times.

3) Push the Start button.

4) Display will show .

is to set price value, time value, vend type, etc. consists of line test, reset, free cycle, and kill cycle. is to collect the usage data.

NOTE

• Do not use , .

• It is used only in inspecting the machine.

+ 56 hidden pages