LG FH069FD2F Manual book

OWNER’S MANUAL
COMMERCIAL WASHER
ENGLISH
INDONESIAN
FH069FD2F
MFL67658593 Rev.01_190507
Original instructions
www.lg.com
Copyright © 2019 LG Electronics Inc. All rights reserved.
TABLE OF CONTENTS
2
TABLE OF CONTENTS
3 PRODUCT FEATURES
4
IMPORTANT SAFETY INSTRUCTIONS
6 BASIC SAFETY PRECAUTIONS 6 GROUNDING INSTRUCTIONS 7
SAFETY INSTRUCTIONS FOR INSTALLATION
8 SAFETY INSTRUCTIONS FOR USE,
CARE, CLEANING, AND DISPOSAL
10
PARTS AND ACCESSORIES
10 Parts 10 Accessories
CONTROL PANEL FEATURES
11
11 OPL type
INSTALLATION INSTRUCTIONS
13
13 Checking and choosing the proper location 14 Unpacking and removing shipping bolts 14 Installing Hole cap 15 Connecting the water lines 16 Connecting the drain line 16 Connecting the auto dosing 17 Leveling the washing machine
18 PREPARATION
18
Precautions for fabric care before wash cycle
19 Fabric care labels 19 Sorting laundry 20 Recommended detergent 20 About the dispenser 21 Loading the dispenser
22 OPERATING YOUR WASHER
23 PROGRAMMING MODE
24 Structure of Programming mode
– Card/Coin type
25
Structure of Programming mode – OPL type
26 PROGRAMMING MODE –SETUP MODE 26 - 1. How to change regular price. 27 - 2. How to change regular delicates price. 28 - 3. How to change regular warm & cold
29 - 4. How to change regular hot price 30 - 5. How to change special price 31 - 6. How to change special delicates price 32 - 7. 33 - 8. How to change special hot price 34 - 9. How to change add super wash price 35 - 10. How to change add super wash type 36 - 11. How to enter the 37 - 11-1. Special price day setup 38 - 11-2. Non-stop rinse setup 39 - 11-3. Add Super Wash setup 40 - 11-4. Vend type setup - card type or coin
price
How to change special warm & cold price
41 - 11-5. Pre-wash setup 42 - 11-6. Twin spray setup 43 - 12. How to enter the 44 - 12-1. Pause function setup 45 - 13. How to enter the special price day 46 - 13-1. How to change to Sunday 47 - 14. Special price beginning time setup 48 - 15. Special price ending time setup 49 - 16. Prewash time setup 50 - 17. Washing time setup 51 - 18. Rinsing time per cycle 52 - 19. Rinsing time setup 53 - 20. Top spin speed – final spin time
54 - 21. Value of coin 1 55 - 22. Value of coin 2 56 - 23. Penny increment pricing offset 57 - 24. How to change the water level 58 - 25. Beep volume 59 - 26. Time to keep the coin (Use only for
60 - 27. How to set drop count 61 - 28. How to set shut down time after UE 62 - 29. How to set rinse spin enable 63 - 30. How to set drop count for rinse spin 64 - 31. How to set auto dosing 65 - 32. How to enter the 66 - 33. How to set custom program 67 PROGRAMMING MODE – TEST MODE 67 - 1. 68 - 2. Factory reset ­69 - 3. Time setup 70 - 4. Courtesy cycle 71 - 5. Cycle Kill 72 - 6. Password ­73 - 7. Tub clean ­74 75 Collect Mode Data lists
type setup
depends on RPM
coin type)
PROGRAMMING MODE – COLLECT MODE
76 MAINTENANCE
76 - Care after wash 76 - Storing the Washer 76 - Cleaning the Dispenser 77 - Cleaning the water inlet filters 78 - Cleaning the drain pump filter 78 - Cleaning the door seal 79 - Clean the drum, TUB CLEAN
80 ERROR MODE
81 POWER FAIL RECOVERY
81 DEFAULT WASHER SETTINGS
82 SPECIFICATIONS
83 LG COMMERCIAL LAUNDRY
LIMITED WARRANTY
PRODUCT FEATURES
3
PRODUCT FEATURES
DIRECT DRIVE SYSTEM
The advanced brushless DC motor drives the drum directly without using a belt and pulley.
TILTED DRUM AND EXTRA LARGE DOOR OPENING
The tilted drum and extra large opening make it possible to load and unload clothing more easily.
ULTRA CAPACITY
The larger drum enables more tumbling action and greater centrifugal force, but also less tangling and wrinkling of the laundry. Heavier loads, such as king size comforters, blankets, and curtains can be washed.
SEE-THROUGH DOOR AND BIG DOOR
You can see the laundry throughout the cycle.
MAGNETIC DOOR PLUNGER
Safely and conveniently secure the door slightly ajar with the magnetic door plunger. This will promote air circulation and allow the interior of the machine to dry. To use this feature, after the load has been removed, do not close the door completely. When the magnetic door plunger comes into contact with the metal washer cabinet, it will secure the door slightly open allowing the interior of the washer to dry.
STAINLESS STEEL DRUM
Stainless steel drum offers extreme durability.
ENGLISH
TUB CLEAN
Regular cleaning of the tub on a monthly basis using TUB CLEAN can help keep the tub clean and fresh.
IMPORTANT SAFETY INSTRUCTIONS
4
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.
Your Safety and the safety of others are very important.
We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.
This is the safety alert symbol.
This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word DANGER, WARNING or CAUTION. These words mean:
DANGER
You will be killed or seriously injured if you don’t immediately follow instructions.
WARNING
You can be killed or seriously injured if you don’t follow instructions.
CAUTION
You may be slightly injured or cause damage to the product if you do not follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.
IMPORTANT SAFETY INSTRUCTIONS
5
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.
The instructions shall state the substance of the following: This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
6
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.
BASIC SAFETY PRECAUTIONS
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following.
Read all instructions before using the washer.
Do not wash articles that have been previously
cleaned in, washed in, soaked in, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.
Do not add gasoline, dry cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.
Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the washing machine, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.
Do not allow children to play on or in the washer.
Close supervision of children is necessary when the washer is used near children.
Before the washer is removed from service or
discarded, remove the door to prevent children from hiding inside.
• Do not install or store the washer where it will be
exposed to the weather.
• Do not tamper with the controls.
• Do not repair or replace any part of the washer
or attempt any servicing unless specifically recommended in the user-maintenance instructions or published user-repair instructions that you understand and have the skills to carry out.
• See Installation Instructions for grounding
requirements.
• ALWAYS follow the fabric care instructions supplied
by the garment manufacturer.
• Do not place items exposed to cooking oil in your
washer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.
• Do not use fabric softeners or products to eliminate
static unless recommended by the manufacturer of the fabric softener or product.
SAVE THESE INSTRUCTIONS
GROUNDING INSTRUCTIONS
This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.
• Do not use an adapter or extension cord.
• Do not remove ground prong.
• If you don’t have the proper outlet, consult an electrician.
WARNING
Improper connection of the equipment-grounding conductor can result in risk of electric shock. Consult a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a proper outlet installed by a qualified electrician.
IMPORTANT SAFETY INSTRUCTIONS
7
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR INSTALLATION
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following.
Refer to INSTALLATION INSTRUCTIONS for detailed grounding procedures.
instructions are packed in the washer for installer's reference. If the washer is moved to a new location, have it checked and reinstalled by a qualified service person. Failure to follow this warning can cause serious injury, fire, electric shock or death.
Do not, under any circumstances cut or remove the third (ground) prong from the power cord.
to follow this warning can cause serious injury, fire, electric shock or death.
For personal safety, this appliance must be properly grounded.
serious injury, fire, electric shock or death.
The power cord of this appliance is equipped with a 3-prong (grounding) plug which fits a standard 3-prong (grounding) wall outlet to
possibillty of electric shock hazard from this appliance.
This washer must be plugged into a 220-240 V~, 50 Hz grounded outlet.
can cause serious injury, fire, electric shock, or death.
Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded.
Failure to follow this warning can cause serious injury, fire, electric shock, or death.
Where a standard 2-prong wall outlet is
encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.
Failure to follow this warning can cause serious injury, fire, electric shock, or death.
Do not install on carpet. Install the washer on a solid floor.
serious leak damage.
Do not remove the ground prong. Do not use an adapter or extension cord. Plug into a grounded 3 prong outlet.
cause serious injury, fire, electric shock, or death.
Failure to follow this warning can cause
Failure to follow this warning can cause
Installation
Failure
minimize the
Failure to follow this warning
Failure to follow this warning can
The washer should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.
performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.
Never unplug your washer by pulling on the power cord. Always grip the plug firmly and pull straight out from the outlet.
cause serious injury, fire, electric shock, or death.
Repair or replace all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.
can cause serious injury, fire, electric shock,or death.
When installing or moving the washer, be careful
not to pinch, crush, or damage the power cord.
Failure to follow this warning can cause serious injury, fire, electric shock, or death.
The washer must be installed and electrically grounded by a qualified service person in accordance with local codes,
hazard and assure stability during operation.
The washer is heavy. Two or more people are needed to install and move the appliance.
do so can result in back or other injury
Store and install the washer where it will not
be exposed to temperatures below freezing or exposed to outdoor weather conditions.
follow this warning can cause serious leak damage.
Do not install the washer in humid spaces to reduce the risk of electric shock.
can cause serious injury, fire, electric shock, or death.
To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long sleeved gloves and safety glasses.
Failure to follow all of the safety warnings in this manual could result in property damage, injury to persons or death.
Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemicals, etc.
Failure to follow this warning can
Failure to do so can result in fire.
This provides the best
Failure to follow this warning
to prevent shock
Failure to
Failure to
Failure to follow this warning
ENGLISH
IMPORTANT SAFETY INSTRUCTIONS
8
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR USE, CARE, CLEANING, AND DISPOSAL
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:
Unplug the washer before cleaning
risk of electric shock.
Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer.
damage the finish.
Do not put oily or greasy rags or clothing on top of the washer.
vapors that could ignite the materials.
Do not wash items that are soiled with vegetable or cooking oil.
contain some oil after laundering. Due to the remaining oil, the fabric may smoke or catch fire by itself.
Disconnect this appliance from the power supply before attempting any user maintenance.
Turning the controls to the OFF position does not disconnect this appliance from the power supply. Failure to follow this warning can cause serious injury, fire, electric shock, or death.
Do not combine laundry products for use in 1 load unless specified on the label. Do not mix chlorine bleach with ammonia or acids such as vinegar.
Follow package directions when using laundry products. Incorrect usage can produce poisonous gasresulting in serious injury or death.
Do not reach into the washer while parts are moving. Before loading, unloading, or adding items, push the START/PAUSE button and allow the drum to coast to a complete stop before reaching inside.
Failure to follow this warning can cause serious injury, fire, electric shock, or death.
to avoid the
They will
These substances give off
These items may
This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety.
Children should be supervised to ensure that they do not play with the appliance.
Do not allow children to play on or in the washer.
Close supervision of children is necessary when the washer is used near children. As children grow, teach them the proper, safe use of all appliances. Failure to comply with these warnings could result in serious personal injuries.
Destroy the carton, plastic bag, and other packing materials after the washer is unpacked.
Children might use them for play. Cartons covered with rugs, bedspreads or plastic sheets can become airtight chambers. Failure to comply with these warnings could result in serious personal injuries.
Keep laundry products out of children's reach.
To prevent injury to persons, observe all warnings on product labels. Failure to comply with these warnings could result in serious personal injuries.
IMPORTANT SAFETY INSTRUCTIONS
9
IMPORTANT SAFETY INSTRUCTIONS
READ ALL INSTRUCTIONS BEFORE USE
WARNING
For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.
SAFETY INSTRUCTIONS FOR USE, CARE, CLEANING, AND DISPOSAL
WARNING
To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:
Remove the door to the washing compartment to avoid the danger of children or small animals getting trapped inside before your washer is removed from service or discarded.
do so can result injury or death.
Before the washer is removed from service or discarded, remove the washer door to prevent accidental entrapment.
Failure to comply with these warnings could result in serious personal injuries.
Unplug the washer before replacing external
Failure to follow this warning can cause
fuse.
serious injury, fire, electric shock or death.
If the supply cord is damaged, it must be replaced by the
Failure to
manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
The new hose-sets supplied with the appliance are to be used and that old hose-sets should not be reused.
ENGLISH
PARTS AND ACCESSORIES
10
PARTS AND ACCESSORIES
Parts
Detergent
dispenser
(for single
model)
Door
Magnet Door
Plunger
(see page 2)
Accessories
Hot and Cold
Water Hoses
Detergent dispenser drawer (for stack model)
Drain pump filter cover Drain pump filter Drain hose
Non-skid pads Caps (4)
Control panel
Door seal
Tu b
Leveling feet
Shipping
(for covering
shipping bolt holes)
Water
inlets
bolts
Power cord
Drain hose
Harness
(for connecting
auto dosing)
(-) (+)
Wrench
(for removing
shipping bolts and
adjusting leveling feet)
Hole cap (5 ) (for securing
auto dosing
hole)
Tie Strap
(for securing drain hose)
Elbow Bracket
(for securing
drain hose)
CONTROL PANEL FEATURES
1 25
11
CONTROL PANEL FEATURES
OPL Type (FH069FD2F)
4
1. Display LED
2. Cycle button
3. Optional function button
ENGLISH
3
4. Start/Pause button
5. Status LED
CONTROL PANEL FEATURES
12
Display LEDStatus LED Cycle button
Display LED
The display shows the vend price and remaining time and programming options. Error
codes are also displayed here.
Cycle button
Press the CYCLE button to select the desired cycle based on laundry types and conditions.
Hot
Use for hot washing for heavy fabrics, such as white clothes, table linens, and heavily soiled clothes.
Warm
Use for warm washing for heavy fabrics, such as jeans, corduroys, or work clothes.
Cold
Use for cold washing for sturdy fabrics, such as casual work.
Delicates
Use for cold washing for synthetic fabrics, such as washable knit fabric and no-iron finishes.
Start/Pause button
Optional function button
Optional function button
Add Super Wash:
be added when additional coin is inserted or a valid cash card is entered.
Custom PGM:
be used. Only available in OPL type.
Wash time or rinse cycle can
Customized cycle program can
Start/Pause button
The Start/Pause LED flashes when the full vend price has been satisfied and the cycle has been chosen.
Status LED
LED Description
LED flashes whenever the Washing cycle is in operation.
LED flashes whenever the Rinsing cycle is in operation.
LED flashes whenever the Spinning cycle is in operation.
LED flashes whenever the door lock is activated.
INSTALLATION INSTRUCTIONS
13
INSTALLATION INSTRUCTIONS
Checking and choosing the proper location
Install the washing machine on a solid floor that is strong and rigid enough to support the weight of the washing machine, even when fully loaded, without flexing or bouncing. If the floor has too much flex, you may need to reinforce it to make it more rigid. If the floor is not solid, it may cause severe vibration and noise.
Clean the floor before installation.
1
- Make sure to select solid and smooth ground.
Two or more people are needed for moving
2
and unpacking the washing machine.
Allow for sufficient space between the walls
3
and the washing machine for installation.
Space requirements
You must allow sufficient space for water lines, the drain line, and airflow.
NOTE
• Be sure to allow for wall, door, or floor
moldings that may increase the required clearances.
Installing on a floor
22
(570mm)
11
/16
38
(983mm)
NOTE
The floor must be strong and rigid enough to support the weight of the washer, when fully loaded, without flexing or bouncing. If your floor has too much flex, you may need to reinforce it to make it more rigid. A floor that is adequate for a top-loading washer may not be rigid enough for a front loading washer, due to the difference in the spin speed and direction. If the floor is not solid, your washer may vibrate and you may hear and feel the vibration throughout your house.
• Before installing the washer, make sure
the floor is clean, dry and free of dust, dirt, water and oils so the washer feet can not slide easily. Leveling feet that can move or slide on the floor can contribute to excess vibration and noise due to poor contact with the floor.
1
/4
1”
(25mm)
3
30
/16
(767mm)
5
/8
52
(1337mm)
27”
(686mm)1”(25mm)
4”
(100mm)
ENGLISH
INSTALLATION INSTRUCTIONS
14
Unpacking and removing shipping bolts
When removing the washer from the carton base, be sure to remove the foam drum support in the middle of the carton base. If you must lay the washer down to remove the base packaging materials, always lay it carefully on its side. DO NOT lay the washer on its front or back.
Foam Tub SupportCarton Base
Remove the bottom two shipping bolts
1
with the wrench (included) to fully loosen all four shipping bolts by turning them counterclockwise and then pulling them out.
Retainer
Shipping
bolt
NOTE
• Save the bolt assemblies for future use. To
prevent damage to internal components, DO NOT transport the washer without reinstalling the shipping bolts.
• Failure to remove shipping bolts and retain­ers may cause severe vibration and noise, which can lead to permanent damage to the washer. The cord is secured to the back of the washer with a shipping bolt to help prevent operation with shipping bolts in place.
Installing Hole cap
Take the hole cap out from manual bag.
1
Hole cap
Insert the hole cap (4 pieces) into hose
2
connect in back of the machine.
Locate the four hole caps included in the
2
accessory pack and install them in the shipping bolt holes.
Cap
NOTE
• In case of using auto dosing feature,
inserting hole cap is unnecessary.
INSTALLATION INSTRUCTIONS
15
Connecting the water lines
Check the rubber seals on both sides of the
1
hose.
- Insert a rubber seal into the threaded fittings on each hose to prevent leaking.
Rubber seal
Water hose (To water inlet on the washing machine)
Connect the water supply hoses to the HOT
2
and COLD water faucets tightly by hand and then tighten another 2/3 turn with pliers.
- Connect the blue hose to a cold water faucet and the red hose to a hot water faucet.
Rubber seal
Water hose (To faucet)
WARNING
Do not overtighten. Damage to the cou-
pling can result.
After connecting inlet hose to water faucets,
3
turn on the water faucets to flush out foreign substances (dirt, sand or sawdust) in the water lines. Let water drain into a bucket, and check the water temperature.
Connect the hoses to the water inlets tightly
4
by hand and then tighten another 2/3 turn with pliers.
- Connect the blue hose to the cold water inlet and the red hose to the hot water inlet.
Cold water
inlet
Hot water inlet
WARNING
Do not overtighten the hoses.
Overtightening can damage the valves resulting in leaking and property damage.
Check for leaks by turning on the faucets.
5
- If water leaks, check steps 1 to 4 again.
NOTE
• For your safety, and for extended product
life, use only authorized components. The manufacturer is not responsible for product malfunction or accidents caused by the use of separately purchased unauthorized parts.
• Use new hoses when you install the
washing machine. Do not reuse old hoses. Use only the inlet hoses provided with the washer. LG does not recommend the use of aftermarket hoses.
• Periodically check the hoses for cracks,
leaks and wear, and replace the hoses every 5 years.
• Do not stretch the water hoses intentional­ly, and make sure that they are not crushed by other objects.
• Water supply pressure must be between
1.,0 kgf/cm² and 8.0 kgf/cm² (0.1 - 0.8 MPa). If the water supply pressure is more than 8.0 kgf/cm², a pressure reducing valve must be installed.
• To provide optimum washing performance
the hot water temperature should be set at 120-135°F (48-57°C) and the cold at 60°F (15°C).
ENGLISH
INSTALLATION INSTRUCTIONS
16
Connecting the drain line
Secure the drain hose in place to prevent moving and leaking.
NOTE
• The drain hose should be properly secured.
Failure to properly secure the drain hose can result in flooding and malfunction.
• Total height of the hose end should not
exceed 39.4 inches (100.0 cm) from the bottom of the washer.
• The drain must be installed in accordance
with any applicable local codes and regula­tions.
• Make sure that the water lines are not
stretched, pinched, crushed, or kinked.
Using a standpipe
Clip the end of the hose into the elbow
1
bracket.
- Connect the elbow bracket within 4 inches (10 cm) from the end of the drain hose. If the drain hose is extended more than 4 inches (10 cm) beyond the end of the elbow bracket, mold or microorganisms could spread to the inside of the washer.
Using a laundry tub
Clip the end of the hose into the elbow bracket.
1
- Connect the elbow bracket within 4 inches (10 cm) from the end of the drain hose. If the drain hose is extended more than 4 inches (10 cm) beyond the end of the elbow bracket, mold, or microorganisms could spread to the inside of the washer.
No more than 4 inches (10 cm)
Elbow Bracket
Hang the end of the drain hose over the side
2
of the laundry tub.
Elbow
Bracket
max. 39.4”
(1.0 m)
Drain Hose
Laundry Tub
max. 39.4”
(1.0 m)
Tie Strap
No more than 4 inches (10 cm)
Elbow Bracket
Insert the end of the drain hose into the
2
standpipe.
Use a tie strap to secure the drain hose in
3
place.
Elbow Bracket
Drain Hose
Use a tie strap to secure the drain hose in
3
place.
Connecting the auto dosing
Unscrew the 2 screws on the protective
1
cover and remove the cover.
Connect the auto dosing harness from
2
Accessory parts.
NOTE
• The voltage of the auto dosing machine
should be the same as the washer's voltage.
Leveling the washing machine
The washer tub of your new washing machine spins at very high speeds. To minimize vibration, noise, and unwanted movement, the floor must be perfectly level and solid.
Check the washing machine’s level.
1
- Check the precise level by rocking the top edges of the washing machine or placing a level on the washing machine. The slope beneath the washing machine must not exceed 1°, and all four leveling feet must rest firmly on the floor.
Turn the lower leveling feet clockwise to
2
level the washing machine.
- Turning the lower leveling feet clockwise raises the washing machine.
Raise
Turn the locknuts counterclockwise and
3
tighten them when the washing machine is level.
Level
INSTALLATION INSTRUCTIONS
Check the washing machine’s level again.
4
- Push or rock the top edges of the washing machine gently to make sure that the washing machine does not rock.
- If the washing machine rocks, repeat steps 1 to 3.
17
WARNING
• Using the washing machine without level­ing, it may result in malfunction caused by the production of excess vibration and noise.
Use the leveling feet only when you level the washing machine. If you raise the level-
ing feet unnecessarily, it may cause abnor­mal vibration of the washing machine.
Using non-skid pads (optional)
If you install the washing machine on a slippery surface, it may move because of excessive vibration. Incorrect leveling may cause malfunction through noise and vibration. In the event of this, lay the non-skid pads under the leveling feet and adjust the level.
1 Clean the floor to attach the non-skid pads.
- Use a dry rag to remove and clean foreign
objects or moisture. If moisture remains, the non-skid pads may slip.
Adjust the level after placing the washing
2
machine in the installation area.
Place the adhesive side of the non-skid pad
3
on the floor.
- It is most effective to install the non-skid
pads under the front legs. If it is hard to place the pads under the front legs, place them under the back legs.
This side up
ENGLISH
Tighten all 4 lock
nuts securely using
the wrench.
Adhesive side
Remove backing
Check the washing machine’s level again.
4
- Push or rock the top edges of the washing
machine gently to make sure that the washing machine does not rock. If the washing machine rocks, level the washing machine again.
PREPARATION
18
PREPARATION
Precautions for fabric care before wash cycle
Read and observe the following to prevent shrinkage or damage to clothes.
uCheck all pockets to make sure that they are
empty.
- Items such as clips, matches, pens, coins, and keys can damage both your washer and your clothes.
uClose zippers, hooks, and drawstrings
to prevent these items from snagging or tangling on other clothes.
uPretreat heavily stained areas before
washing.
- Doing so will produce clean, stain-free results.
uCombine large and small items in a load.
Load large items first.
uLarge items should not be more than half of
the total washload.
uThe washer can be fully loaded, but the
drum should not be tightly packed with items.
- The door of the washer should close easily.
uDo not wash single items, except for bulky
items such as blankets. Make sure to wash laundry in similar types of loads.
- Washing a single small item may result in the tub becoming unbalanced, vibrating, making a noise.
uBrush heavy soil, dust, or hair off fabrics
before washing.
- Laundry may not wash clean if there is dirt or sand on the fabrics, or they may be damaged due to particles rubbing against sheer fabrics.
uWash blankets individually.
- Washing more than one blanket together may produce unclean results due to tangling or an unbalanced load.
uAlways separate fabrics according to their
colors and wash them separately to prevent colors from running.
- Fabrics may damage or become stained due to fabric dyes running or due to foreign objects transferring from one fabric to another.
uDo not wash waterproof clothes.
- This may cause abnormal vibration or may cause the load to bounce, which could damage the tub.
uCheck if there are any other foreign objects
in the door seal and take extra care that clothes do not get caught there.
- Foreign objects in the door seal may stain clothes, and water may leak if clothes get caught in the door seal.
uWash underwear or small, light items in a
laundry net.
- Small, light items may get caught in the door seal, and a brassiere hook may damage other items or the tub.
PREPARATION
19
Fabric care labels
Most articles of clothing feature fabric care labels that include instructions for proper care.
Category Label Directions
Hand Wash
Machine Wash, Normal Cycle
Use Permanent Press/ Wrinkle Resistant washing machine setting (which has a cool down or cold spray before the reduced spin)
Washing
Use Gentle/Delicate washing machine setting (slow agitation and/ or reduced wash time).
Do Not Wash
Do Not Wring
Hot
Sorting laundry
It is recommended that you sort laundry into similar loads that are washable in the same cycle. Refer to the following chart for sorting clothes
Colors
Soil
Fabric
Lint
Whites / Lights / Darks
Heavy / Normal / Light
Delicates / Easy Care / Sturdy Cottons
Lint Producers / Lint Collectors
ENGLISH
Water
Temperature
Bleach
symbols
Warm
Cold/Cool
Any Bleach (When Needed)
Only Non-Chlorine Bleach (When Needed)
Do Not Bleach
PREPARATION
20
Recommended detergent
Use HE (High-Efficiency) detergent for front­loading washing machines. HE detergents dissolve more efficiently and produce fewer suds to ensure efficient washing and rinsing. Use the correct amount of detergent as indicated on the label of the detergent packaging.
NOTE
• Use HE detergents, since using a regular
detergent will produce excessive suds.
• HE detergents produce fewer suds,
dissolve more efficiently to improve washing and rinsing performance, and help to keep the interior of your washer clean.
• Use less detergent for soft water.
• Wipe up any spills immediately, as liquids
could damage the finish and the control panel of the washing machine.
• Using too much detergent can cause
a build-up in the tub resulting in unsatisfactory performance and machine malfunction.
• If you use a detergent that does not
dissolve easily or a detergent with high viscosity, it will leave a residue on the tub, which may not rinse properly.
About the dispenser
The automatic dispenser consists of three compartments which hold:
• Liquid chlorine bleach.
• Liquid fabric softener.
• Liquid and powdered detergent and color-
safe bleach for main wash. All laundry products can be added at once in their respective dispenser compartments. They will be dispensed at the appropriate time for the most effective cleaning. After adding the laundry products to the dispenser, close the dispenser cover.
To add detergent, bleach, and fabric softener to the automatic dispenser:
1. Open the dispenser cover.
2. Load the laundry products into the
appropriate compartments.
3. Slowly close the dispenser cover to avoid
early dispensing of the laundry products.
NOTE
• It is normal for a small amount of water to
remain in the dispenser compartments at the end of the cycle.
PREPARATION
21
Loading the dispenser
Main Wash Detergent Compartment
This compartment holds laundry detergent for the main wash cycle, which is added to the load at the beginning of the cycle. Use HE (High-Efficiency) detergent with your washing machine. Follow the detergent manufacturer's instructions with respect to the amount of detergent to use, and never use more than the recommended amount. Using too much detergent can result in detergent buildup in clothing and the washer. Either powdered or liquid detergent may be used.
NOTE
• Liquid or powdered color-safe bleach may
be added to the main wash compartment with detergent of the same type.
- Single model -
Main Wash
Detergent
Compartment
Liquid Chlorine
Bleach Compartment
- Stack model -
Main Wash Detergent
Compartment
Liquid Fabric
Softener Compartment
ENGLISH
Liquid Bleach Compartment
This compartment holds liquid chlorine bleach, which will be dispensed automatically at the proper time during the wash cycle.
NOTE
• Do not add powdered or liquid color-safe
bleach to this compartment.
• Always follow the manufacturer’s recom­mendations when adding bleach. Do not exceed the maximum fill line. Using too much bleach can damage fabrics.
• Never pour undiluted liquid chlorine bleach
directly onto the load or into the drum. Fabric damage can occur.
Fabric Softener Compartment
This compartment holds liquid fabric softener, which will be automatically dispensed during the final rinse cycle.
NOTE
• Always follow the manufacturer’s recom­mendations when adding fabric softener. Do not exceed the maximum fill line. Us­ing too much fabric softener may result in stained clothes.
• Dilute concentrated fabric softeners with
warm water. Do not exceed the maximum fill line.
• Never pour fabric softener directly onto
the load or into the drum.
• Do not add the fabric softener sheets to
this compartment.
• Do not add ‘ fabric sheet softener’ into
the dispenser draw as it is likely to cause
water to leak out. If ‘ fabric sheet softener’
has been added, please pull out the dis­penser draw and remove.
Liquid Chlorine
Bleach Compartment
Liquid Fabric
Softener Compartment
OPERATING YOUR WASHER
22
OPERATING YOUR WASHER
1. Ready mode
1) Coin / Card type
– The cycle LEDs are lit at the same
time, when the prices of cycles are equal.
2) OPL type
– The cycle LEDs flash at the same time,
and displays PUSH.
NOTE
• Price setting varies by country
• Set your country from
(Refer
How to enter the
• After EEPT, reset your country (Default
country is EUK)
2.
Insert card/coin (not for OPL type)
Insert a cash card that has a sufficient balance.
The card balance should be more than the programmed vend price for a selected cycle.
mode
)
NOTE
• When the card balance is not enough,
machine displays the card balance for 5 seconds and then displays sage repetitively
• Insert a sufficient amount of change that
is more than the programmed vend price for the selected cycle.
mes-
NOTE
• The machine will not start until sufficient
coins are inserted.
3. Select the cycle
Press the desired button and press the
Start button. The display LED will show the remaining time and the selected cycle starts.
• Select cycles designed for different types of
fabric and soil levels.
CYCLE Fabric type
Hot
Warm
Cold
Delicates
Cotton, linen, towels, shirts, sheets
Cotton, mixed loads, work clothes, jeans, shirts
Cotton, dress shirts, pants, wrinkle-free clothing, cotton/ poly blend clothing, tablecloths
Dress shirts, blouses, nylons, sheer or lacey garments
Wash/Rinse
Temp.
Hot / Cold
Warm / Cold
Cold / Cold
Cold / Cold
4. Add Super Wash
Wash time or rinse cycle can be added
when additional coin is inserted or a valid cash card is entered.
5. Custom PGM
Customized cycle program can be used.
Only available in OPL type.
6. Change course
You cannot change the cycle while the
machine is running.
7. Cycle finish
The machine stops and LED display shows
with beeper sound.
Do not work any button and stop the washer
(When the washer is operating) or (when a cycle is in progress)
WARNING
• To reduce the risk of fire, electric shock, or
injury to persons, read the IMPORTANT SAFETY INSTRUCTIONS before operating this appliance.
PROGRAMMING MODE
23
PROGRAMMING MODE
: You can check machine information or change setting on Program setup, Collect Information Data,
Diagnostic Test. There are two methods that you can enter programming mode.
How to enter Programming mode
You can enter programming mode only for Idle state and pause state.
- Card Type
1) Insert service card.
2) Display will show
- Coin Type
1) Dissemble upper coin box key.
2) Take out the coin drop from the coin box.
3) Turn on/off the toggle switch at the back of the coin box.
4) Display will show
- All Types
1) Push the Hot & Cold button at the same time.
2) Push the Warm button 3 times.
3) Push the Start button.
4) Display will show
Coin Box Key Coin Vault Openings close
.
.
.
Insert Debit Card
How to use button
You can change Washer vend price, cycle time and Cycle parameters, etc.
Press Button Description
Hot
Warm
Cold
Start Enters the selected mode
Moves to upper level or
Comes back to Idle State
Moves through modes in the
same level (+)
Moves through modes in the
same level (-)
ENGLISH
- coin type - - card type - - OPL type -
NOTE
• If you turn on the power without connecting meter case for the first time, the machine display
• When the machine is shipped from the factory, it is set in the coin type. You can change Card/
• The machine will display PUSH for OPL type
• Price setting varies by country
• Set your countr y from
• After EEPT, reset your country (Default country is EUK)
.
Coin type by button. (For more information refer to SETUP mode.)
mode (Refer
How to enter the
)
PROGRAMMING MODE
24
Structure of Programming mode – Card / Coin type
Algorithm flow chart shows how to control the programming mode.
Before program set, check the structure of the programming mode.
1. Turn on/off toggle switch or insert service card, for entering setup mode (or follow OPL type instructions).
2. Press Hot button to move to the upper level.
3. Press Warm (+) or Cold (-) button if you want to be at the same level.
4. Press Start button to enter the details of Setup or Diagnostic Tests.
is to set price value, time value, vend type, etc. consists of line test, reset, free cycle, and kill cycle. is to collect the usage data.
NOTE
• Do not use , .
• It is used only in inspecting the machine.
• Price setting varies by country
• Set your countr y from
• After EEPT, reset your country (Default country is EUK)
mode (Refer
How to enter the
)
PROGRAMMING MODE
25
Structure of Programming mode – OPL type
Algorithm flow chart shows how to control the programming mode. Before program set, check the structure of the programming mode.
The method of entering setup mode.
1) Push the Hot & Cold button at the same time.
2) Push the Warm button 3 times.
3) Push the Start button.
4) Display will show
is to set price value, time value, vend type, etc. consists of line test, reset, free cycle, and kill cycle. is to collect the usage data.
.
ENGLISH
NOTE
• Do not use , .
• It is used only in inspecting the machine.
PROGRAMMING MODE - SETUP MODE
26
PROGRAMMING MODE –SETUP MODE
Setup Mode : (display)
You can change washer vend price, cycle time, and cycle parameters, etc.
Entering setup mode
- Coin type – Turn on/off toggle switch.
- Card type – Insert the service card.
- All Types – 1) Push the Hot & Cold button at the same time.
2) Push the Warm button 3 times.
3) Push the Start button.
- Then, the washer displays
1. How to change regular price.
.
Enter setup mode.
You will see LqC1
Button Display
Press the
Press the in the display.
Press the
Press the Display previous regular price.
Press (The vend price can be set from 0~10.00 in 0.1 increments.)
Press the The machine sets up the regular price, then advances to the next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• All types - Push the Hot button twice.
Hot
Warm
Start
Start
Warm(+)
Start
button.
or the
button.
button.
or
Cold(-)
button.
button until appears
Cold
button to set the regular price.
NOTE
• Price setting varies by country
• Set your countr y from
• After EEPT, reset your country (Default country is EUK)
mode (Refer
How to enter the
)
PROGRAMMING MODE - SETUP MODE
27
2. How to change regular delicates price.
Enter setup mode.
You will see LqC1
Press the
Press the in the display.
Press the
Press the in the display.
Press the Display previous regular delicates price.
Press delicates price. (The vend price can be set from 0~10.00 in 0.1 increments.)
Press the The machine sets up the regular delicates price, then advances to the next process automatically.
Hot
Warm
Start
Warm
Start
Warm(+)
Start
button.
button.
button.
or
button.
Button Display
or the
or the
Cold(-)
button until appears
Cold
button until appears
Cold
button to set the regular
ENGLISH
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• All types - Push the Hot button twice.
NOTE
• Price setting varies by country
• Set your countr y from
• After EEPT, reset your country (Default country is EUK)
mode (Refer
How to enter the
)
PROGRAMMING MODE - SETUP MODE
28
3. How to change regular warm & cold price
Enter setup mode.
You will see LqC1
Button Display
Press the
Press the in the display.
Press the
Press the in the display.
Press the Display previous regular warm & cold price.
Press & cold price. (The vend price can be set from 0~10.00 in 0.1 increments.)
Press the The machine sets up the regular warm & cold price, then advances to the next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• All types - Push the Hot button twice.
Hot
Warm
Start
Warm
Start
Warm(+)
Start
button.
or the
button.
or the
button.
or
Cold(-)
button.
button until appears
Cold
button until appears
Cold
button to set the regular warm
NOTE
• Price setting varies by country
• Set your countr y from
• After EEPT, reset your country (Default country is EUK)
mode (Refer
How to enter the
)
PROGRAMMING MODE - SETUP MODE
29
4. How to change regular hot price
Enter setup mode.
You will see LqC1
Press the
Press the in the display.
Press the
Press the in the display.
Press the Display previous regular hot price.
Press price. (The vend price can be set from 0~10.00 in 0.1 increments.)
Press the The machine sets up the regular hot price, then advances to the next process automatically.
Hot
Warm
Start
Warm
Start
Warm(+)
Start
button.
or the
button.
or the
button.
or
Cold(-)
button.
Button Display
button until appears
Cold
button until appears
Cold
button to set the regular hot
ENGLISH
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• All types - Push the Hot button twice.
NOTE
• Price setting varies by country
• Set your countr y from
• After EEPT, reset your country (Default country is EUK)
mode (Refer
How to enter the
)
PROGRAMMING MODE - SETUP MODE
30
5. How to change special price
Enter setup mode.
You will see LqC1
Button Display
Press the
Press the in the display.
Press the
Press the in the display.
Press the Display previous special price.
Press (The vend price can be set from 0~10.00 in 0.1 increments.)
Press the The machine sets up the special price, then advances to the next process automatically.
1. Continue to set up the next price.
2. Stop the change of setup value and go back to ready mode.
• Coin type - Turn on/off toggle switch.
• Card type - Pull the service card.
• All types - Push the Hot button twice.
Hot
Warm
Start
Warm
Start
Warm(+)
Start
button.
or the
button.
or the
button.
or
Cold(-)
button.
button until appears
Cold
button until appears
Cold
button to set a special price.
NOTE
• Price setting varies by country
• Set your countr y from
• After EEPT, reset your country (Default country is EUK)
mode (Refer
How to enter the
)
Loading...
+ 138 hidden pages