Hose
Retainer
Tie
strap
max. 100 c m
min. 60 cm
Ownerʻs Manual
F1403YD(1~9)
Read all instructions and explanations of the installation before use. Follow the instructions carefully. Keep the operating
instructions handy for later use. If the appliance is sold or passed on then ensure that the new owner always receives these
operating instructions. The following warnings must be strictly observed for safety reasons. They must be read before installing the appliance and putting it into operation.
• Intended use: This appliance has been designed exclusively for use in dry-interior households. Use the appliance only with cold
drinking water and only for washing textiles with washing detergents designed for washing machines. Every other use is improper
and may lead to injuries, whereby the liability of the manufacturer will cease.
• This appliance may only be used by adults. Do not allow children to touch the controls or to play with the product.
• Never modify the appliance on your own, as this is dangerous.
• This appliance is heavy. Transporting with care.
• Remove all packaging and transport bolts before using the appliance. Otherwise serious damage may result.
• All installation work must be carried out by a qualifi ed fi tter or technician.
• Have electrical connections done by a qualifi ed electrician.
• Never place the appliance on the power cord.
• If the appliance is placed on a carpet then place the feet so that air can circulate underneath the appliance.
• Always unplug the machine and turn off the water supply after use. Disconnect appliance by pulling only the plug - never disconnect
by pulling the power cord. Never touch the plug with wet fi ngers or hands.
• Do not overload the appliance.
• Wash only machine-washable textiles. If you have doubts regarding this, then observe the markings on the label.
•
Never place electrical heaters, candles etc. in the vicinity of the appliance. They could cause the appliance to ignite or parts to warp.
• Protect the appliance from wet and damp. Otherwise, there is danger of electric shock and fi re.
• Connect the appliance to a suitable wall socket for 220-240V. Never use an extension cord or double adapter.
• Empty all pockets. Hard or sharp objects such as coins, needles, nails, screws or stones may cause serious damage.
Unbalanced mass may create heavy vibrations. If heavy vibrations remain also without load, call for an authorized customer service.
• Do not wash or dry articles that have been cleaned in, washed in, soaked in, or dabbed with combustible or explosive substances
(such as wax, oil, paint, gasoline, degreasers, dry-cleaning solvents, kerosene, etc.). This may result in fi re or explosion.
• Never insert products coated with mineral oils (e.g. nylon coating, plastic belts, etc. ) into the machine. If a stain remover has been
used then make sure that the solvent has been carefully washed out before inserting the clothes into the appliance. Oil may remain
in the tub after a whole cycle resulting in fi re during drying. So, do not load oily clothes.
• Do not operate the appliance at locations where fl ammable substances are present such as oil, benzene or highly infl ammable gas.
Such materials may cause fi re or explosion. Never use combustible detergents.
• Only add the prescribed amount of softener. Excessive amounts may damage the clothes.
• After washing, keep the drum door open to protect the door seal.
• Make sure that all water has run off before opening the door. Never open the door if water still remains. Danger of scalding.
• Animals and children may get into the washing machine. So always check the appliance before using it.
• During washing, the glass door becomes very hot. Keep children away from the appliance when in operation.
• Never try to repair the machine yourself. Incorrect repairs may result in injuries and/or serious defects to the machine.
• The product should be serviced and repaired only by the authorised customer service using original replacement parts.
•
When disposing of your old machine, the power cable must be capped and the door lock must be made unusable in order to protect children.
• When placing on a carpeted fl oor, make sure that the opening in the socket is not blocked.
• If the appliance has been under water then contact the customer service. There is danger of electric shock and fi re.
• The cover cup of the fi lter as well as the dispenser drawer may not be opened during the operation.
• Keep all washing powder and detergents away from children. Danger of poisoning
Disposal
• When this crossed-out wheeled bin symbol is attached to a product it means the product is covered
by European Directive 2002/96/EC.
• All electrical and electronic products should be disposed of separately from municipal waste stream
via designated collection facilities appointed by the government or the local authorities.
• The correct disposal of your old appliance will help prevent potential adverse consequences for the
environment and human health.
• For more detailed information about disposal of your old appliance, please contact your city offi ce,
waste disposal service or the shop where you purchased the product.
Safety instructions for use
Safety instuctions for the installation
Install or store the appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit the power plug
to a grounded wall socket that complies with all statutory regulations and ordinances. Ensure that the base opening is free from
obstruction by carpeting if the washing machine is installed on a carpeted fl oor. In countries where there is a risk of cockroach
infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times.
Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.
CAUTION about positioning the appliance
Install the washing machine on a fl at hard fl oor. Make sure that air circulation around the washing machine is
not impeded by carpets, rug etc.
•
Never try to correct any unevenness in the fl oor using pieces of wood, cardboard or similar materials under the washing machine.
•
If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel
(85x60cm ) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.
•
The washing machine must not be installed in rooms where the temperature may drop below 0°C.
•
Please ensure that when the washing machine is installed , that a Service Technician can gain easy access in the event of a
breakdown.
•
Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between
the top of the washing machine and underside of the worktop.
CAUTION about the power cord
We recommend connecting most appliances to a dedicated circuit which is protected by a mains fuse. That is, a single outlet
supplying power only to the appliance concerned, without any additional outlets or branch circuits. Check the specifi cations
of this owner‘s manual. Do not overload wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension
cords, frayed power cords, damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric
shock or fi re. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it,
discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect
the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or
walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the appliance.
CAUTION about location and moving
This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the
stopcock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no fl oor drain
(gully) in the immediate vicinity. If relocating the appliance use the original packing material. Packaging material (e.g. plastic fi lm,
Styrofoam) can be dangerous for children. There is a risk of suffocation! Keep all packaging well away from children and do not
allow children to play inside the bowl as they may become trapped.
CAUTION about the fl oor surface
• The installation surface must be clean, dry and level.
• Install washing machine on a fl at hard fl oor. Poorly constructed timber base fl oors can contribute to excessive noise and
vibration.
• Proper placement and levelling of the washing machine ensure long, regular and reliable operation.
• The washing machine must be perfectly level and fi rmly in position.
• It must not “see-saw” across corners under load.
• The installation surface must be clean, free from fl oor wax and other lubricant coatings.
• Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.
Name of product
Front loading washing machine
Power supply
220-240 V~, 50 Hz
Size WxDxH mm:
600 x 640 x 850
Weight
72 kg
Max. Wat t
2100 W (Wash ) / 1500 W ( Dry)
Capacity
8 kg
(Wash ) /
4 kg
(Dry)
Water consumption
90
Permissible water pressure
1.0-10 bar (100-1000kPa)
Technical Specifi cation
1 3
5
2 4
Turn off the
water tap
Unscrew the
water inlet hose
Pull out the water
inlet filter
Clean the filter using
a hard bristle brush
Pull out the
dispenser drawer
Clean the dispenser
drawer under
flowing water
Clean inside the
recess with an
old toothbrush
Insert the
dispenser drawer
Cleaning the water inlet filter
Cleaning the dispenser drawer
Open the lower
filter cover and pull
out the drain hose.
Unplug the drain
hose plug
Then
open the filter by
turning to the lef t
Remove any
extraneous
matter from the
pump filter
After cleaning, refit the
drain filter cap and tighten it
by turning it clockwise. and
insert the drain plug
Tighten up the
inlet hose
Close the lower
cover
Once you
have finished
cleaning, replace
the drawer and
run a rinse cycle
without laundry or
soap.
Warning: Before cleaning the washing machine interior, unplug the electrical power cord to avoid the risk of electric
shock.
Exterior
Proper care of your washing machine can extend its service life.
The outside of the machine can be cleaned with warm water and
a neutral non-abrasive household detergent. Immediately wipe off
any spillage. Wipe with damp cloth. Avoid striking the sur face with
sharp objects. Never hose down the machine!
Interior
Dry around the washing machine door
opening, flexible gasket and door
glass. Run washing machine through a
complete cycle using hot water. Repeat
process if necessary.
Cleaning in general
Important: Do not use methylated spirits, solvents or similar products.
Cleaning and Maintenance
Cleaning the drain pump filter
Installation of drain hose
• The drain hose should not be placed higher than 100 cm above the fl oor.
• Proper securing of the drain hose will protect the fl oor from damage due to any water leakage.
• If the drain hose is too long do not force back into the washing machine. This will cause abnormal
noise and cause the machine to malfunction and leak.
Electrical connection
1. Do not use an extension cord or double adapter.
2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualifi ed person to
prevent danger.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
• Repairs to the washing machine must only be carried out by qualifi ed personnel. Repairs carried out by inexperienced persons may cause injury or serious malfunctioning. Contact your local service centre.
• Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may
burst under pressure. The electronic control unit may become unreliable at temperatures below freezing point.
• If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine
standing at room temperature for a few hours before putting it into operation.
Rattling and clanking noise Extraneous objects such as coins or safety pins maybe in drum or pump.
Thumping sound Heavy wash loads may produce a thumping sound. This is usually normal.
Vibrating noise Have all transit bolts and packing been removed?
Water leaks. Check and tighten hose connections. Unclog drain pipe. Contact plumber if necessary.
Excessive suds Too much detergent or unsuitable detergent.
Washing machine does not start Power cord may not be plugged in or connection may be loose.
Washing machine won’t spin Check that the door is shut.
Check that foreign objects may be blocking the drain causing the water not to drain out.
Door does not open Once started, the door can not be opened for safety reasons.
At the end of the cycle or when Start Pause is pressed, wait one or two minutes before opening the door to
allow the electric locking mechanism time to release.
Troubleshooting
• Water supply is not adequate in area
• Water supply taps are not completely
open.
• Water inlet hose(s) are kinked.
• The fi lter of the inlet hose(s) are
clogged.
Check another tap in the house.
Fully open tap.
Straighten hose(s).
Check the filter of the inlet hose(s).
• Drain hose is kinked or clogged.
• The drain fi lter is clogged.
Clean and straighten the drain hose.
Clean the drain filter.
For more detailed information, please
refer to “Cleaning the drain pump filter”
• Load is too small.
• Load is out of balance.
• The appliance has an unbalance detection
and correction system. If individual heavy
articles are loaded (ex. bath mat, both
robe, etc.), this system may stop spinning
or even interrupt the spin cycle altogether.
• If the laundry is still too wet at the end of
the cycle, add smaller articles of laundry
to balance the load and repeat the spin
cycle. Floor is unstable.
Feet are not adjusted
Add 1 or 2 similar items to help balance
the load.
Rearrange load to allow proper spinning
• Is the door opened or not
completely closed?
Close the door completely.
If the " " does not clear, call for
service.
Unplug the power plug and call for
service.
• Water overfi lls due to the faulty water
valve.
Close the water tap.
Unplug the power plug.
Call for service.
Restart the cycle.
• Water level sensor has malfunctioned.
• Over load in motor.
• The washer experienced a power
failure.
• Check water supply.
CAUTION
• The appliance is not intended for use by young children or infi rm persons without supervision.
• Young Children should be supervised to ensure that they do not play with appliance.
CAUTION
The hose supplied with the machine must be used.
Old hoses may not be reused.
The fl oor should be a solid surface.
Adjust the feet so that the machine
does not rock from side to side or front
to back.
Before use please read carefully the safety instructions!
Thank you for buying an LG fully automatic washing machine.
Please read this owner‘s manual carefully, it provides instructions on safe installation, use and maintenance.
Keep it handy for future reference of this machine. Make a note of the model and serial numbers of your
washing machine.
P/No. : MFL62883821
For the U.K. customer
CUSTOMER SERVICES Tel. : +44-(0 ) 844 847 LGLG(5454) Fax. : +44- (0) 844 847 1413
LGEUK SERVICE WEB-SITE : http://www.lge.co.uk
Turn the tap on.
If “ ” is not released, unplug
power plug and call for service.
Safety instructions for use
To minimize the risk of fi re within the inner bowl, the following should be observed:
• Items that have been spotted or soaked with vegetable or cooking oil constitute a fi re hazard and should not be
placed in a tumble dryer.
Oil-affected items can ignite spontaneously, especially when exposed to heat sources Such as in a tumble dryer.
The items become warm, causing an oxidation reaction in the oil. Oxidation creates heat. If the heat cannot
escape, the items can become hot enough to catch fi re. Piling, stacking or storing oil-affected items can prevent
heat from escaping and so create a fi re hazard.
If it is unavoidable that fabrics that contain vegetable or cooking oil or have been contaminated by hair care prod-
ucts be placed in a tumble dryer they should fi rst be washed in hot water with extra detergent-this will reduce,
but not eliminate, the hazard. The ‘cool down’ cycle of tumble dryers should be used to reduce the temperature
of the items. They should not be removed from the tumble dryer or piled or stacked while hot.
• Items that have been previously cleaned in, washed in, soaked in or spotted with petrol/gasoline, dry-cleaning
solvents or other fl ammable or explosive substances should not be placed in a tumble dryer.
Highly fl ammable substances commonly used in domestic environments include acetone, denatured alcohol,
petrol/gasoline, kerosene, spot removers (some brands), turpentine, waxes and wax removers.
• Items containing foam rubber (also known as latex foam) or similarly testured rubber like materials should not be
dried in a tumble dryer on a heat setting.
Foam rubber materials can, when heated, produce fi re by spontaneous combustion.
• Fabric softeners or similar products should not be used during a drying cycle, to eliminate the effects of static
electricity unless this practice is specifi cally recommended by the manufacturer of the fabric softener or product.
• Undergarments that contain metal reinforcements should not be placed in a tumble dryer.
Damage to the tumble dr yer can result if metal reinforcements come loose during drying.
When available a drying rack could be used for such items.
• Plastic articles such as shower caps or babies waterproof napkin covers should not be placed in a tumble dryer.
• Rubber-backed articles, clothes fi tted with foam rubber pads, pillows, rubber boots and rubber-coated tennis
shoes should not be placed in a tumble dryer.
BS Plug Safety Details (For U.K. User)
Green
Yellow )
Brown(Live)
Blue(Neutral)
Fuse
Cord
grip
E
L
N
and
(Earth)
This appliance must be earthed As the colours of the wires in the mains
lead of this apparatus may not correspond with the coloured markings
identifying the terminals in your plug, proceed as follows: The green and
yellow wire must be connected to the terminal in the plug marked E or by
the earth symbol or coloured green or green and yellow.
The wire coloured blue must be connected to the terminal marked with the letter N or coloured black.
The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. If a 13
amp (BS 1363) plug is used, fi t a 13 amp BS 1362 fuse.