LG F1402FDS5, F1402FDS, F1402FDS1, F1402FDS2, F1402FDS3 Owner's Manual

...
arantiebedingungen
G
Entsorgung von Altgeräten
1. Wenn dieses Symbol eines durchgestrichenen Abfalleimers auf einem Produkt angebracht ist, unterliegt dieses Produkt der europäischen Richtlinie 2002/96/EC.
2. Alle Elektro- und Elektronik-Altgeräte müssen getrennt vom Hausmüll über dafür staatlich vorgesehenen Stellen entsorgt werden.
3. Mit der ordnungsgemäßen Entsorgung des alten Geräts vermeiden Sie Umweltschäden und eine Gefährdung der persönlichen Gesundheit.
4
1
2
3
5
7
1 2
3 4
6
Adjustable feet
60 - 100 cm
@
N
Green and
Yellow (Earth)
Brown(Live)
Blue(Neutral)
Fuse
Cord grip
E
L
N
noituloSesuaC elbissoPmotpmyS
Water supply is not adequate in area
Water supply taps are not completely open.
Water inlet hose(s) are kinked.
The filter of the inlet hose(s) are clogged.
• Drain hose is kinked or clogged.
• The drain filter is clogged.
• Load is too small.
• Load is out of balance.
The appliance has an unbalance detection and correction system. If individual heavy articles are loaded (ex. bath mat, both robe, etc.), this system may stop spinning or even interrupt the spin cycle altogether.
If the laundry is still too wet at the end of the cycle, add smaller articles of laundry to balance the load and repeat the spin cycle.
• Is the door opened or not completely closed?
Water overfills due to the faulty water valve.
Water level sensor has malfunctioned.
• Over load in motor.
Water leaks
• The washer experienced a power failure.
Check another tap in the house. Fully open tap. Straighten hose(s). Check the filter of the inlet hose(s).
Clean and straighten the drain hose. Clean the drain filter. For more detailed information, please refer to Cleaning the drain pump filter
Add 1 or 2 similar items to help balance the load. Rearrange load to allow proper spinning
Unplug the power plug and call for service.
Close the water tap. Unplug the power plug. Call for service.
Call for service.
Restart the cycle.
Close the door completely.
If “ ” is not released, call for service.
Owners Manual
F1402FDS(1~9)
Safety inst ructions f or use
Read all instructions and explanations of the ins tallation before use. Follow the instructions carefully. Keep the operating instructions handy for later use. If the appliance is s old or passed on then ensure that the new owner always receives these operating instructions. The following warnings must be strictly observed for safet y reasons. They must be read before instal­ling the appliance and putting it into operation.
• In tended use: This applia nce has been designed exc lusively for use in dr y-interior household s. Use the appliance on ly with cold drinking water and only for washi ng textiles with wa shing detergents desi gned for washing machin es. Every other use is im proper and may lead to injuries, whereby the liab ility of the manufa cturer will cease.
• T his appliance may onl y be used by adults. Do not allo w children to touch the co ntrols or to play with t he product.
• Ne ver modify the app liance on your own, as thi s is dangerous.
• T his appliance is heav y. Transporting with ca re.
• Re move all packaging and t ransport bolts b efore using the applia nce. Otherwise ser ious damage may result.
• A ll installation wor k must be carried out b y a qualified fitter or te chnician.
• Ha ve electrical con nections done by a qual ified electrician.
• Ne ver place the applia nce on the power cord.
• If t he appliance is plac ed on a carpet then plac e the feet so that air ca n circulate underneat h the appliance.
• A lways unplug the machi ne and turn off the wa ter supply after use. Di sconnect applianc e by pulling only the plu g - never disconnect by pulling the power cord. Never touch t he plug with wet fingers or h ands.
• Do n ot overload the applia nce.
• Was h only machine-washab le textiles. If you have dou bts regarding this, the n observe the mar kings on the label.
• Ne ver place electric al heaters, candles et c. in the vicinity of th e appliance. They coul d cause the applianc e to ignite or parts to w arp.
• Prot ect the appliance fr om wet and damp. Otherw ise, there is danger of elec tric shock and fire.
• C onnect the applianc e to a suitable wall soc ket for 220-240V. Never use an extension cord or dou ble adapter.
• Em pty all pockets. Hard or s harp objects such a s coins, needles, nails, scr ews or stones may cause s erious damage. Unbalanced mass may create heav y vibrations. If heav y vibrations remai n also without load, ca ll for an authorized c ustomer service.
• Do n ot wash or dry art icles that have been cle aned in, washed in, soaked i n, or dabbed with combu stible or explosive su bstances (such as wax, oil, paint, gasoline, degreas ers, dry-cleaning so lvents, kerosene, etc.). This may resul t in fire or explosion.
• Ne ver insert product s coated with minera l oils (e.g. nylon coating, plastic b elts, etc. ) into the machine. If a s tain remover has been used then make sure that the solve nt has been carefully w ashed out before inser ting the clothes in to the appliance. Oil may re main in the tub after a whole cycle resul ting in fire during dr ying. So, do not load oily clothe s.
• Do n ot operate the applian ce at locations where fla mmable substance s are present such as oil, be nzene or highly inflamma ble gas. Such materials may cause fire or explo sion. Never use combust ible detergents.
• On ly add the prescribe d amount of softener. Exces sive amounts may dama ge the clothes.
• Af ter washing, keep the d rum door open to protect t he door seal.
• Ma ke sure that all water has r un off before opening t he door. Never open the door if wa ter still remains. Dange r of scalding.
• A nimals and children may g et into the washing machi ne. So always check the ap pliance before using it.
• Du ring washing, the glas s door becomes ver y hot. Keep children away from t he appliance when in o peration.
• Ne ver try to repair th e machine yourself. Incor rect repairs may result i n injuries and/or seri ous defects to the mach ine.
• T he product should be ser viced and repaired o nly by the authoris ed customer servi ce using original repl acement parts.
• When disposing of yo ur old machine, the power ca ble must be capped an d the door lock must be made u nusable in order to protec t children.
• Wh en placing on a carpete d floor, make sure that the openi ng in the socket is not blocke d.
• If t he appliance has be en under water then cont act the customer ser vice. There is danger of e lectric shock and fi re.
• T he cover cup of the filter as w ell as the dispenser d rawer may not be opened duri ng the operation.
• Kee p all washing powder an d detergents away from chi ldren. Danger of poisoning
Disposal
Before use please read carefully the safety instructions!
Thank you for buying an LG fully automa tic washing machine.
Please read this owner‘s manual ca refully, it provides inst ructions on safe inst allation, use and main tenance.
Keep it handy for future reference of t his machine. Make a note of the mo del and serial number s of your washing machine.
Remove Packaging
Requirement s for insta llation site
Transit bolts
Electrical c onnection
Connecting wa ter supply h ose
• The appliance is fitted with transit bolts to prevent inter nal damage during transport. Be careful, heavy load!
• Packing and all transit bolts must be removed before using the washing machine.
• When unpacking the base, be sure to remove the additional packing support in the middle of the base packing.
Store original packing for future move. Dispose of packing material according to local regulations.
Unscrew the 4 bolts using the spanner supplied.
Keep the 4 bolts and the spanner for the future use. Ret transit bolts before transporting the appliance.
Level floor: Permissible floor gradient under entire washing machine is 1˚ .
Power socket: Must be within 100 cm of either side of location of washing machine. Do not overload the socket with more than one appliance.
Additional Clearance: For wall, floor and door spac e is needed. (10cm: rear / 2cm:right & left side). Do not place or store laundry pro­ducts on top of the washing machine at any times. They can damage the finish or controls of the machine.
1. Do not use an extension cord or double adapter.
2. Have damaged supply cords replaced by the manufacturer or its service agents or a similarly qualied person to prevent danger.
3. Always unplug the machine and turn off the water supply after use.
4. Connect the machine to an earthed socket in accordance with current wiring regulations.
5. The appliance must be positioned so that the plug is easily accessible.
Repairs to the washing machine must only be carried out by qualied personnel. Repairs carried out by inexpe - rienced persons may cause injury or serious malfunctioning. Contact your local service centre.
Do not install your washing machine in rooms where temperature below freezing may occur. Frozen hoses may burst under pressure. The electronic control unit may become unreliable at temperatures below freezing point.
If the appliance is delivered in the winter months and temperatures are below freezing: Leave the washing machine standing at room temperature for a few hours before putting it into operation.
• Two rubber seals are supplied with the water inlet hoses. They are used for preventing water leaks.
• Make sure the connection to taps is tight enough.
• Periodically check the condition of the hos e and replace the hose if necessary.
• Make sure that there is no kink on the hose and that it is not crushed.
When your washing machine has two valves:
• The inlet hose with the red connector is for the h ot water tap.
• If the washing machine has two valves, power saving is achieved through using hot valve.
Water supply pressure must be between 1.0-10 bar (100kPa~1000kPa)
Don’t strip or crossthread when connecting inlet hose to the valve.
If the water supply pressure is more than 1000kPa, a decompressio n device should be installed.
• The drain hose should not be placed higher than 100 cm above the floor.
• Proper securing of the drain hose will protect the floor from da mage due to any water leakage.
• If the drain hose is too long do not force back into the washing machine. This w ill cause unusual noise.
• Proper level-adjustment of t he washing ma­chine prevents excessive noise and vibration. Install the appliance on a solid and level floor surface, preferably in a corner of the room.
• If the floor is uneven, adjust fe et as required. (Do not insert pieces of wood etc. under the feet). Make sure that all four feet are stable and resting on the floor. Then check that the appliance is perfectly level. (Use a spirit level).
Safety inst uctions fo r the install ation
Install or store appliance where it will not be exposed to sub-zero temperatures or exposed to the weather. Fit ground of the washing machine correctly to conform with all statutory regulations and ordinances. Ensure that the base opening is free from obstruction by carpeting if the washing machine is installed on a carpeted oor. In countries where there is a risk of cockroach infestation or other vermin, pay particular attention to keep the appliance and its surroundings in a clean condition at all times. Any damage which may be caused by cockroaches or other vermin is not covered by the appliance guarantee.
CAUTION about positioning the applianc e
Install the washing machine on a flat hard floor. Make sure that air circulation around the washing machine is not impeded by carpets, rug etc.
Never try to correct any unevenness in the floor using pieces of wood, cardboard or similar materials under the washing machine.
If it is not possible to position the washing machine away from a gas cooker or coal burning stove, an insulation panel (85x60cm) covered with aluminum foil on the side facing the cooker or stove, must be inserted between the two appliances.
The washing machine must not be installed in rooms where the temperature may drop below 0°C.
Please ensure that when the washing machine is installed an engineer can gain easy access in the event of a breakdown.
Adjust all four feet using the transit bolt spanner provided to ensure that the appliance is stable, with 20mm clearnace between the top of the washing machine and underside of the worktop.
CAUTION about the power cord
We recommend connecting most appliances to a dedicated circuit. That is, a single outlet supplying power only to the appliance concerned, without any additional outlets or branch circuits. Check the specications of this owners manual. Do not overload wall sockets. Overloaded wall sockets, loose or damaged wall sockets or extension cords, frayed power cords, damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or re. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized servicer. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, squashed in a jamb of a door, or walked upon. Pay particular atten - tion to plugs, wall outlets, and the point where the cord exits the appliance. We recommend to use a residual current operated device in the mains supply.
CAUTION about location and moving
This equipment is not designed for maritime use or for use mobile installations such as caravans, aircraft etc. Turn off the stop - cock if the machine is to be left for any length of time (e.g. if you are going on holiday), especially if there is no oor drain (gully) in the immediate vicinity. If relocating the appliance use the original packing material. Disable the door lock to prevent young children becoming trapped inside. Packaging material (e.g. plastic lm, Styrofoam) can be dangerous for children. There is a risk of suffocation! Keep all packaging well away from children.
CAUTION about the floor surface
The installation surface must be clean, dry and level.
Install washing machine on a flat hard floor.
Proper placement and levelling of the washing machine ensure long, regular and reliable operation.
The washing machine must be perfectly level and firmly in position.
It must not “see-saw” across corners under load.
The installation surface must be clean, free from floor wax and other lubricant coatings.
Do not allow the feet of the washing machine to get wet. If feet of the washing machine get wet, slipping may occur.
Name of product Front loading washing machine
Power supply 220-240 V~, 50 Hz
Size WxDxH mm: 600 x 640 x 850
Weight 65 kg
Max. Watt
2100 W (Wash) / 1100 W (Steam)
Wash capacity 9 kg
Water consumption 59 l (6.5l / kg)
Permissible water pressure 1.0-10 bar (100-1000kPa)
Rattling and clanking noise Extraneous objects such as coins or safety pins maybe in dr um or pump. Thumping sound Heavy wash loads may p roduce a thumping sound. This is usually normal. Vibrating noise Have all transit bolts and pa cking been removed? Water leaks. Check and tighten hose connections. Unclog drain pipe.
Contact plumber if necessary.
Excessive suds Too much detergent or unsuitable detergent. Washing machine does not start Power cord may not be plugged in or connection may be loose. Washing machine won’t spin Check that the door is firmly shut. Door does not open Once started, the door can not be opened for safety reaso ns.
Wait one or two minutes before opening the door to allow the electric locking mechanism time to release.
Troubleshooting
Level adjustm ent
To prevent internal dama­ge during transport, the special 4 bolts are locked. If they are not removed, it may cause heavy vibrati­on, noise and machine to malfunction.
Installation of drain hos e
Technical Speci fication
i
If after completing connection water leaks from the hose, repeat th e same steps. Use the most conventional type of tap for water supply. In case the faucet is square or too big, remove the spacing ri ng before inserting the tap into the adaptor.
i
BS Plug Safety Details (For U.K. User)
This appliance must be earthed As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The green and yellow wire must be connected to the terminal in the plug marked E or by the earth symbol or
coloured green or green and yellow. The wire coloured blue must be connected to the terminal marked with the letter N or coloured black. The wire coloured brown must be connected to the terminal marked with the letter L or coloured red. If a 13 amp (BS 1363) plug is used, fit a 13 amp BS 1362 fuse.
For the U.K. customer
CUSTOMER SERVICES Tel. : 0870 - 873 - LGLG (5454) Fax. : 0870 - 872 - 7337
LGEUK SERVICE WEB-SITE : http://uk.lge.com
i
• Wh en this crossed-out wh eeled bin symbol is at tached to a product it mea ns the product is covere d by European Directive 2002/96/EC.
• A ll electrical and e lectronic products s hould be disposed of sep arately from municipa l waste stream via designated collection faci lities appointed by t he government or the loc al authoritie s.
• T he correct disposa l of your old appliance wil l help prevent potential a dverse consequen ces for the environment and human health.
• Fo r more detailed informa tion about disposa l of your old appliance, ple ase contact your cit y office, waste disposal service or t he shop where you purcha sed the product.
The hose supplied with the machine must be used. O ld hoses may not be reused
Close the holes with the caps supplied.
Remove the 4 bolts along with the rubber bungs by slightly twisting the bung.
P/No. :MFL38868793
tE
FE
PE
LE
AE
PF
1
2
3
A
C
B
A
B
C
1 2 3 4 5
1 3
Program
Fabric Type
Water Temp.
(Option)
Cotton
Lightly soiled clothing and small loads
40
°C
(Cold,
30°C, 60°C)
Cotton, underwear, pillow covers, bed sheets, baby wear
Cotton Quick
Synthetic
Baby Care
Allergy
Care
Delicate
Quick 30
Refresh
Hand Wash
/Wool
Color fast garments (shirts, nightdresses, pajamas...)and lightly soiled white cotton (underwear)
Polyamide, Acrylic, Polyester
Lightly soiled baby wear
Delicate laundry easily damaged
“Hand wash” marked delicate and wool laundry
Colored laundry which is lightly soiled fast
Cotton mixed, Polyester mixed Dress shirts, blouses
- Time Delay
- Steam Wash
- Intensive
- Time Delay
- Steam Default
- Intensive
- Soak
- Pre Wash
- Crease Care
- Crease Care
- Rinse+Spin
- Medic Rinse
- Rinse+Spin
- Medic Rinse
- Time Delay
- Intensive
- Crease Care
- Rinse+Spin
- Steam Default
60°C (Cold, 30°C, 40°C, 95°C)
Less than 7 kg
Rating
Less than 4.5kg
Less than 3.0kg
Less than 2.0kg
3 items
40°C (Cold, 30°C, 60°C)
30°C
(Cold, 40°C)
30°C
(Cold, 40°C)
40°C
(Cold, 30°C)
No Choose
60°C
(40°C, 95°C)
60°C
Maximum Load
Option
1 2 3 4 5
1 2 3 4 5
5
2
Pre Wash
Soak
Pre Wash
Soak
Rinse + Spin Crease care
Pre Wash
Soak
Rinse + Spin
Crease care
Rinse++ Hold Normal + Hold
Rinse
++
Rinse
+
Normal
Pre Wash
Soak
+
+ Hold
Rinse
++
Rinse
+
Normal
95°C 60 40 30 Cold
1 2 3 4 5
4
Warning: Keep all was hing powd er and d etergent s away f rom chil dren. Da nger of po isonin g
INSERT PLU S INTO THE MA INS SOC KET
Nev er touc h the plu g with w et hands ! Nev er remov e the pl ug from t he soc ket by pu lling on the cor d.
HANG UP WA STE WATE R HOSE
Hose elbow c onnecti on e.g. at tach to w ater ta p
WATER CONNE CTION
Turn on the wat er tap
CHECKING T HE MAC HINE
Never use a d efectiv e machin e! In ca se of any failure, fir st unplu g the mac hine an d turn o ff the water
tap.
DOING LAU NDRY AN D USIN G MACHI NE WITH CARE
- empty all p ockets
- remove all m etal pa rts
- place the d elicate textil es into t he laun dry net
- close zipp ers
WATER TREAT MENT
- with hardn ess III water
- use water s oftenin g agent
DRUM CARE
- remove ext raneous objects
- leave door open to d ry the drum
- check the r ubber s eals reg ularly
ECOLOGICA L WASHI NG
- make use of the max. washin g quanti ty
- do not “pre wa sh” if po ssible
- use short program if possi ble
LAUNDRY W ITH DI FFEREN T AMOU NTS OF SOILING
- wash new textil es sepa rately
- do not pre wash
- pretreat dirty spots
- pre wash
Sort the lau ndry
note washing instru ction s ymbols -
Degree of soi ling -
Type of textil e / colo ur -
Fill the drum
Check the fo lds of th e flexib le gask et (grey) -
and remove an y small articl es, if a ny.
.
Check inside of the d rum and remove ­any left in i tems for next wa sh cycl e.
.
Remove any cl othing o r items on the f lexible gasket -
to prevent c lothing and the gasket d amages
.
Fill detergen t
Refer to the
written in formati on
on the deterg ent's pa cking
Turn the machin e ON
by pressing the Powe r butto n
Select a
Program
Select the
Spinning spee d
Select an
Option
Pre Wash / Soa k / Crea se Care / Rinse + Spin
Select
Rinse mode
and
Washing tempe rature
4 additional programs
Press Star t / Pause to start th e washi ng proce ss
Turn off tap
- Close water supply
- Clean the m achine
- Unplug mach ine
Additional S teps
- Turn the mac hine off
- Leave door o pen to allow drum to dry
Remove laundr y
- Open the do or
- Remove the laundr y
W
ai
t
u
n
t
i
l
w
a
s h
in
g
i
s
f
i
n
i
s
h
e
d
Time Delay / Steam Wa sh / Inte nsive / Medic Ri nse
Main Wash
For very di rty cl othes fi ll 1/4 of the portion of deterge nt in here and select a prew ashing programm
Softener
Do not exceed the MA X-Level. Highly dens ed softe ners ar e to be diluted w ith some water.
Pre Wash
For normal d irty c lothes u se a sma ll amount of det ergent. D on't pre wash. Mount the le vel plat e to use f luid det ergents .
Dry flat
Do not bleach
Handy to bleach
Do not tumble dry
Hang to dry
Drip dry
Medium hot ironing
Hot ironing
Do not iron
Washing temperature
Do not wash
Luke warm ironing
Turn off the w ater tap
Unscrew the water inlet hose
Pull out the water inlet filter
Clean the f ilter us ing a hard brist le brus h
Pull out the dispenser d rawer
Clean the di spense r drawer under flow
-
ing water
Clean insid e the recess with an old toothbrush
Insert the dispens er drawer
Cleaning the w ater inlet fi lter
Cleaning the d ispenser dra wer
Open the low er cover cap. Drain pl ug to pull out the hose
Unplug the d rain plu g. Then open th e filte r by turning t o the lef t
Remove any extraneous matter from the pum p filter
After clea ning, tur n the pump fil ter and insert the drain pl ug
Time Delay
Setting “Tim e Delay” d etermines when machi ne stops.
How to set “Ti me Delay”
- Press
Power button .
- Turn the
Program dial to selec t the pr ogram yo u require.
- Press
Time Delay but ton and set time require d.
- Press the
Start/Pa use but ton.
Intensive
If the laundr y is heavil y soiled “ Intensiv e”option is effecti ve.
- By selecti ng the I ntensiv e option, the was hing du ration m ay be ext ended, depending on the pr ogram se lected.
- To use this op tion, pr ess the intensi ve butt on once before t he wash p rogram i s star ted.
Medic Rinse
For best resul ts or fo r cleaner r insing, s elect the “Medic Ri nse” optio n.
Available in the Cot ton, Cot ton Qui ck, Synt hetic, A llergy C are and Baby Ca re progra ms. Medic Rinse is set by default in the B aby Care program. The respect ive temp erature indicat or will light up.
Steam Washing a nd Refresh cycle
Steam Wash is
- For heavil y stain ed cloth es, unde rwear, or baby cl othes.
- Steam Wash is avail able wi th the C otton, C otton Q uick, Sy ntheti c, Baby C are, Alle rgy Care program s.
- Refresh cy cle is al ways St eam was h.
- Do not load d elicate s such a s wool, s ilk, and easily discolo red clot hes.
Program Temperature Program Temper ature
Cotton
Cold, 30°C, 40°C, 60°C, 95°C
Baby Care 40°C, 60°C, 95° C
Cotton Quic k Cold, 30°C, 4 0°C, 60°C
Refresh No choose
Synthetic Co ld, 30°C, 40 °C, 60°C Allerg y Care 60°C
How to use Ref resh Cycl e
Spinning cycle
Temperature
Rinse
OptionsStart / PauseProgram Cy cle
Power button
Drum
Dispenser drawer
Cover cap
Control pan el
Washing program table
Additional pro grams
Child Lock
Tub Clean
To activate:
press and ho ld the Option b uttons simultaneo usly
To deactivate:
press and ho ld the Option b uttons simultaneo usly
Change to the d esired pr ogram, wh ilst in chi ld lock mo de:
Empty the d rum completly a nd clos e the door
Add anti-lime scale (Calgon) to t he main wash compar tment. Close the di sp. drawe r
Power ON wit h Then press a nd hold Rinse a nd Temp. button
Press the Start/ Pa use button to st art Tub Clean proce ss
After the c ycle is complete, lea ve the door open to dry
Turn on machin e by pressing the power butto n
Press and ho ld the buttons sim ultane
-
ously for 3 s econds
Display show s the different l anguage s
Select your language
Acknowledg e your selection
Select this fun ction t o lock th e butto ns on the contro l panel a nd to pre vent tam pering.
Press and ho ld the Option b uttons simultaneo usly
Press Start/Pa use
Select the d esired program
press Start/Pa use
TUB CLEAN is speci al cycle to clean the insi de of the washing machine. A higher water le vel is us ed in thi s cyle at higher s pin spee d. Perf orm thi s cycle r egular ly.
Preparation
lightly
heavily
Tighten up t he inlet hose
Cleaning the d rain pump filt er
Close the lo wer cover cap
Washing symbols
Dispenser dra wer
Once you have finished cleaning, repla ce the drawer and run a rinse cyc le without laundr y.
Changing the la nguage
Cleaning and Ma intenance
Warning: Befo re cleanin g the wash ing machin e interior, unplug the electri cal power c ord to av oid the ri sk of elec tric sho ck.
DisplayAdditional pro grams
Steam Cycle
Note:
To use programs in the Steam-Cycle, please press first the “S team Was h” butt on (see additio nal prog rams).
Refresh Allergy Care Baby Care Cotton SyntheticCotton Quick
1
6 3 sec.
6 3 sec.
6 3 sec.
Exterior Proper care o f your wa shing m achine c an exte nd its s ervice life. Th e outside of t he machi ne can b e clean ed with warm wat er and a neutra l non-abrasive househ old dete rgent. Im mediate ly wipe o ff any s pillage. Wipe with da mp clot h. Avoid st rikin g the sur face w ith sha rp objec ts. Neve r hose down th e machin e!
Interior
Dry around the wash ing mach ine doo r opening, flex ible ga sket and door gla ss. Run washing machine through a comple te cycle using hot water. R epeat pr ocess i f necessar y.
Cleaning in ge neral
Important: D o not use methyl ated spi rits, so lvents or simil ar produ cts.
6 3 sec.
By pressing the Ste am Wash b utton, S team Fu nction c an be se lected. When Steam F unction is sele cted, Ste am wash (
ow to use washer
H
4. Medic Rinse
For high effectiveness or more purity in rinse operation you can choose Medic Rinse option.
3. Intensive
If the laundry is heavily soiled “Intensive” option is effective.
By selecting the Intensive option, the wash time may be extended, depending on the program selected.
To use this option, press the intensive button once before the wash program is started.
) LED lights up.
Steam Washing features enhance wa shing per formance with low energy consump tion. Ref resh cycle reduces creases in clothes .
Select the R efresh program
Load 3 items o r less and close th e door
Press the St eam Wash button repeate dly unt il the required and correc t number of items is displ ayed
Press the Start/Pa use button
2 41
The Beep on/o ff func tion ca n be set by press ing and holding the Option a nd Rins e butto n simult aneous ly.
Beep on / of f
The Beep on/o ff func tion ca n be set at any t ime and i t is automatica lly can celled i n the ev ent of a p ower cut . The Beep on/o ff func tion al so work s when p ower is o ff.
3
Water Temperat ure: Sele ct wate r tempera ture to suit was h cycle s. Alway s follow garment manufa cture’s c are labe l or inst ructi ons when washin g. Intensive: If the lau ndry is heavil y soiled “Intens ive” opti on is ef fectiv e.
Set program a t “Cotto n 60°C + S team Was h + Inten sive” opt ion for t est in a ccordan ce or in conform ity wi th EN604 56 and IE C60456.
Pre Wash: If t he laun dry is h eavily soiled, “ Pre Wash” C otton i s recomm ended. P re Wash is availa ble in th e Cotto n, Cotto n Quick, Synthe tic and Baby Ca re progra m. Crease Care: If you w ant to pr event cr easing, s elect C rease Ca re optio n. Medic Rinse: F or best results or for c leaner r insing, you can choose M edic Rin se opti on. Medic Rinse i s set by d efault i n the Ba by Care p rogram.
The wool was h cycle of this m achine h as been approve d by Woolm ark for the was hing of ma chine wa shable Woolmar k produc ts provi ded tha t the pro ducts a re washed acco rding to the inst ructi ons on t he garme nt label and th ose issu ed by th e manufa cturer of this w ashing machine M0708.
Notes
Neutral de tergent i s recomm ended. T he wool c ycle fe atures g entle t umbling a nd low-s peed spi n for gar ment ca re.
2
6 3 sec.
Loading...