LG F1069FD3 Owner’s Manual

OWNER’S MANUAL

COMMERCIAL WASHER

Before beginning installation, read these instructions carefully. This will simplify installation and ensure that the washer is installed correctly and safely. Leave these instructions near the washer after installation for future reference.

MODEL F1069FD/F1069FD6/F1069FD2 F1069FD4/F1069FD7/F1069FD3

P/No.: MFL62526884

www.lg.com

PRODUCT FEATURES

DIRECT DRIVE SYSTEM

The advanced Brushless DC motor directly drives the drum without using a belt and pulley.

TILTED DRUM AND EXTRA LARGE DOOR OPENING

The tilted drum and extra large opening make it possible to load and unload clothing more easily.

ULTRA CAPACITY

The larger drum enables more tumbling action and greater centrifugal force, but also less tangling and wrinkling of the laundry. Heavier loads, such as king size comforters, blankets, and curtains, can be washed.

SEE-THROUGH DOOR AND BIG DOOR

You can see the laundry throughout the cycle.

STAINLESS STEEL DRUM

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.

Your Safety and the safety of others are very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety

messages.

This is the safety alert symbol. This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word DANGER, WARNING or CAUTION. These words mean:

DANGER

You will be killed or seriously injured if you don’t immediately follow instructions.

WARNING

You can be killed or seriously injured if you don’t follow instructions.

CAUTION

You may be slightly injured or cause damage to the product if you do not follow instructions. All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can

happen if the instructions are not followed.

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.

BASIC SAFETY PRECAUTIONS

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:

•

Read all instructions before using the washer.

•

Do not wash articles that have been previously cleaned in,

washed in, soaked in, or spotted with gasoline, dry cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode.

•

Do not add gasoline, dry cleaning solvents, or other flammable or explosive substances to the wash water. These substances give off vapors that could ignite or explode.

•

Under certain conditions, hydrogen gas may be produced in a hot water system that has not been used for 2 weeks or more. HYDROGEN GAS IS EXPLOSIVE. If the hot water system has not been used for such a period, before using the washing machine, turn on all hot water faucets and let the water flow from each for several minutes. This will release any accumulated hydrogen gas. As the gas is flammable, do not smoke or use an open flame during this time.

•

Do not allow children to play on or in the washer. Close

supervision of children is necessary when the washer is used near children.

•

Before the washer is removed from service or discarded,

remove the door to prevent children from hiding inside.

• Do not install or store the washer where it will be exposed

to the weather.

• Do not tamper with the controls.

• Do not repair or replace any part of the washer or attempt

any servicing unless specifically recommended in the user-maintenance instructions or published user-repair instructions that you understand and have the skills to carry out.

• See Installation Instructions for grounding requirements.

• ALWAYS follow the fabric care instructions supplied by the

garment manufacturer.

• Do not place items exposed to cooking oil in your washer.

Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

• Do not use fabric softeners or products to eliminate static

unless recommended by the manufacturer of the fabric softener or product.

SAVE THESE INSTRUCTIONS

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

• Do not use an adapter or extension cord.

• Do not remove ground prong.

• If you don’t have the proper outlet, consult an electrician.

WARNING

Improper connection of the equipment-grounding conductor can result in risk of electric shock. Consult a qualified electrician or serviceman if you are in doubt as to whether the appliance is properly grounded. Do not modify the plug provided with the appliance - if it does not fit the outlet, have a proper outlet installed by a qualified electrician.

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

IMPORTANT SAFETY INSTRUCTIONS

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.

SAFETY INSTRUCTIONS FOR INSTALLATION

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:

•

Refer to INSTALLATION INSTRUCTIONS for detailed grounding procedures.

Installation instructions are packed in the washer for installer's reference. If the washer is moved to a new location, have it checked and reinstalled by a qualified service person. Failure to follow this warning can cause serious injury, fire, electric shock or death.

•

Do not, under any circumstances cut or remove the third (ground) prong from the power cord.

Failure to follow this warning can cause serious injury, fire, electric shock or death.

•

For personal safety, this appliance must be properly grounded.

Failure to follow this warning can cause serious injury, fire, electric shock or death.

•

The power cord of this appliance is equipped with a 3-prong (grounding) plug which fits a standard 3-prong (grounding)

wall outlet to

from this appliance.

•

This washer must be plugged into a 220-240 V~, 50 Hz grounded outlet.

serious injury, fire, electric shock, or death.

•

Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded.

Failure to follow this warning can cause serious injury, fire, electric shock, or death.

•

Where a standard 2-prong wall outlet is encountered, it

is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet.

Failure to follow this warning can cause serious injury, fire, electric shock, or death.

•

Do not install on carpet. Install the washer on a solid floor.

Failure to follow this warning can cause serious leak damage.

•

The openings must not be obstructed by a carpet.

•

Do not remove the ground prong. Do not use an adapter or

extension cord. Plug into a grounded 3 prong outlet.

Failure to follow this warning can cause serious injury, fire, electric shock, or death.

•

The washer should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate.

This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

minimize the possibillty of electric shock hazard

Failure to follow this warning can cause

•

Never unplug your washer by pulling on the power cord. Always grip the plug firmly and pull straight out from the

Failure to follow this warning can cause serious injury,

outlet.

fire, electric shock, or death.

•

Have a Qualified person repair or replace all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end.

Failure to follow this warning can cause serious injury, fire, electric shock,or death.

•

When installing or moving the washer, be careful not to

pinch, crush, or damage the power cord.

this warning can cause serious injury, fire, electric shock, or death.

•

The washer must be installed and electrically grounded by

a qualified service person in accordance with local codes,

prevent shock hazard and assure stability during operation.

•

The washer is heavy. Two or more people are needed to install and move the appliance.

Failure to do so can result in back or other injury

•

Store and install the washer where it will not be exposed

to temperatures below freezing or exposed to outdoor weather conditions.

Failure to follow this warning can cause serious leak damage.

•

Do not install the washer in humid spaces to reduce the risk of electric shock.

Failure to follow this warning can cause serious injury, fire, electric shock, or death.

•

To reduce the risk of injury to persons, adhere to all industry recommended safety procedures including the use of long sleeved gloves and safety glasses.

the safety warnings in this manual could result in property damage, injury to persons or death.

•

Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemicals,

Failure to do so can result in fire.

etc.

Failure to follow

Failure to follow all of

IMPORTANT SAFETY INSTRUCTIONS

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, injury to persons, or death.

SAFETY INSTRUCTIONS FOR USE, CARE, CLEANING, AND DISPOSAL

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using the washer, follow basic precautions, including the following:

•

Unplug the washer before cleaning

electric shock.

•

Never use harsh chemicals, abrasive cleaners, or solvents to clean the washer.

•

Do not put oily or greasy rags or clothing on top of the washer.

the materials.

•

Do not wash items that are soiled with vegetable or cooking oil.

Due to the remaining oil, the fabric may smoke or catch fire by itself.

•

Disconnect this appliance from the power supply before attempting any user maintenance.

Turning the controls to the OFF position does not disconnect this appliance from the power supply. Failure to follow this warning can cause serious injury, fire, electric shock, or death.

•

Do not combine laundry products for use in 1 load unless specified on the label. Do not mix chlorine bleach with ammonia or acids such as vinegar.

Follow package directions when using laundry products. Incorrect usage can produce poisonous gasresulting in serious injury or death.

•

Do not reach into the washer while parts are moving. Before loading, unloading, or adding items, push in the cycle selector knob and allow the drum to coast to a complete stop before reaching inside.

Failure to follow this warning can cause serious injury, fire, electric shock, or death.

•

This appliance is not to be used by children or persons with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction.

These substances give off vapors that could ignite

These items may contain some oil after laundering.

to avoid the risk of

They will damage the finish.

•

Children should be supervised not to play with the appliance.

•

Do not allow children to play on or in the washer.

Close supervision of children is necessary when the washer is used near children. As children grow, teach them the proper, safe use of all appliances. Failure to comply with these warnings could result in serious personal injuries.

•

Destroy the carton, plastic bag, and other packing materials after the washer is unpacked.

Children might use them for play. Cartons covered with rugs, bedspreads or plastic sheets can become airtight chambers. Failure to comply with these warnings could result in serious personal injuries.

•

Keep laundry products out of children's reach.

To prevent injury to persons, observe all warnings on product labels. Failure to comply with these warnings could result in serious personal injuries.

•

Remove the door to the washing compartment to avoid the danger of children or small animals getting trapped inside before your washer is removed from service or discarded.

Failure to do so can result injury or death.

•

Before the washer is removed from service or discarded, remove the washer door to prevent accidental entrapment.

Failure to comply with these warnings could result in serious personal injuries.

•

Washing Machine is to be connected to the water mains

using new hose-sets and that old hose-sets should not be used.

TABLE OF CONTENTS

2 PRODUCT FEATURES

3 IMPORTANT SAFETY INSTRUCTIONS

4 BASIC SAFETY PRECAUTIONS 4 GROUNDING INSTRUCTIONS 5 SAFETY INSTRUCTIONS FOR INSTALLATION 6 SAFETY INSTRUCTIONS FOR USE, CARE,

CLEANING, AND DISPOSAL

PARTS AND ACCESSORIES

8 Parts 8 Accessories

CONTROL PANEL FEATURES

9 Coin type 10 Card type 10 OPL type

INSTALLATION INSTRUCTIONS

12 Checking and choosing the proper location 13 Unpacking and removing shipping bolts 14 Connecting the water lines 15 Connecting the drain line 16 Leveling the washing machine

17 PREPARATION

17 Precautions for fabric care before wash cycle 18 Fabric Care Labels 18 Sorting laundry 19 Using detergent/fabric softener 19 - Recommended detergent 19 - About the dispenser 20 - Loading the dispenser

21 OPERATING YOUR WASHER

22 PROGRAMMING MODE

32 - 8. How to change special hot price 33 - 9. How to change add super wash price 34 - 10. How to change add super wash type 35 - 11. How to enter the FEA1

36 - 11-1. Special price day setup 37 - 11-2. Add super wash setup 38 - 11-3. Vend type setup - card type or coin type setup 39 - 11-4. Pre-wash set up 40 - 12. How to enter the special price day 41 - 12-1. How to change to Sunday 42 - 13. Special price beginning time setup 43 - 14. Special price ending time setup 44 - 15. Washing time set up 45 - 16. Rinsing times per cycle 46 - 17. Rinsing time setup

47 - 18. Top spin speed – final spin time depends on

RPM

48 - 19. Value of coin 1 49 - 20. Value of coin 2 50 - 21. Penny increment pricing offset 51 - 22. How to change the water level 52 - 23. Beep volume 53 - 24. Time to keep the coin (Use only for coin type)

54 Programming Mode - Test mode 54 - 1. LqC1 55 - 2. Factory reset -EEPt 56 - 3. Time set up

57 - 4. Courtesy cycle 58 - 5. Cycle Kill 59 Programming Mode - Collect mode

60 Collect Mode Data lists

61 MAINTENANCE

61 Care after wash 61 - Storing the Washer 61 - Cleaning the Dispenser 62 - Cleaning the water inlet filters 63 - Cleaning the drain pump filter 64 - Cleaning the door seal

23 Card/Coin type -Structure of Programming mode 24 OPL type -Structure of Programming mode 25 Programming mode - Setup Mode 25 - 1. How to change regular price. 26 - 2. How to change regular cold price. 27 - 3. How to change regular warm price 28 - 4. How to change regular hot price 29 - 5. How to change special price

30 - 6. How to change special cold price 31 - 7. How to change special warm price

65 ERROR MODE

66 POWER FAIL RECOVERY

66 DEFAULT WASHER SETTINGS

66 SPECIFICATIONS

PARTS AND ACCESSORIES

Parts

Detergent

dispenser

drawer

Control panel

Water inlets

Door

Magnet Door

Plunger

Accessories

Drain pump filter cover

Drain pump filter

Drain hose

Hot and Cold

Water Hoses

Doo r seal

Tub

Leve ling feet

Non-skid pads

Shipping

bolts

Power cord

Drain hose

Caps (4)

(for covering shipping bolt holes)

Wrench

(for removing

shipping bolts and adjusting

leveling feet)

(for securing drain hose)

Tie Strap

Elbow Bracket

(for securing drain hose)

4 3

1 25

CONTROL PANEL FEATURES

Coin type

- Side by side (F1069FD4)

CONTROL PANEL FEATURES

Coin type

- Stack (F1069FD)

Optional function button

1. Display LED

2. Cycle button

3. Optional cycle button

4. Start button

5. Status LED

4 3

1 25

CONTROL PANEL FEATURES

Card type

- Side by side & Stack (F1069FD7, F1069FD6)

Optional function button

OPL type

- Side by side & Stack (F1069FD3, F1069FD2)

1. Display LED

2. Cycle button

3. Optional cycle button

Optional function button

4. Start button

5. Status LED

CONTROL PANEL FEATURES

Display LEDStatus LED Cycle button

Display LED

The display shows the vend price and remaining time and programming options. Error codes are also displayed here.

Cycle button

Press the CYCLE button to select the desired cycle based on laundry types and conditions.

WHITES

Use for hot washing for heavy fabrics, such as white clothes, table linens, and heavily soiled clothes.

COLORS

Use for warm washing for heavy fabrics, such as jeans, corduroys, or work clothes.

Start button

Optional function button

Wash time or rinse cycle can be added when additional coin is inserted or a valid cash card is entered.

Start button

The START LED flashes when the full vend price has been satisfied and the cycle has been chosen.

Status LED

LED Description

LED flashes whenever the washing cycle is in operation.

LED flashes whenever the Rinsing cycle is in operation.

LED flashes whenever the Spining cycle is in operation.

DELICATES

Use for cold washing for synthetic fabrics, such as washable knit fabric and no-iron finishes.

PERM. PRESS

Use for warm washing for sturdy fabrics, such as work casual work.

LED flashes whenever the door lock is activated.

INSTALLATION INSTRUCTIONS

Checking and choosing the proper location

Install the washing machine on a solid floor that is strong and rigid enough to support the weight of the washing machine, even when fully loaded, without flexing or bouncing. If the floor has too much flex, you may need to reinforce it to make it more rigid. If the floor is not solid, it may cause severe vibration and noise.

Clean the floor before installation.

- Make sure to select solid and smooth ground.

Two or more people are needed for moving and

unpacking the washing machine.

Allow for sufficient space between the walls and the

washing machine for installation.

Space requirements

You must allow sufficient space for water lines, the drain line, and airflow.

Installing on a floor

/4”

(57 cm)

/4”

(75.6 cm)

51”

(129.7 cm)

4”

(10 cm)

NOTE

• Be sure to allow for wall, door, or floor moldings that

may increase the required clearances.

1”

(2.5 cm)

NOTE

• The floor must be strong and rigid enough to support the weight of the washer, when fully loaded, without flexing or bouncing. If your floor has too much flex, you may need to reinforce it to make it more rigid. A floor that is adequate for a top-loading washer may not be rigid enough for a front loading washer, due to the difference in the spin speed and direction. If the floor is not solid, your washer may vibrate and you may hear and feel the vibration throughout your house.

• Before installing the washer, make sure the floor is

clean, dry and free of dust, dirt, water and oils so the washer feet can not slide easily. Leveling feet that can move or slide on the floor can contribute to excess vibration and noise due to poor contact with the floor.

27”

(68.6 cm)

1”

(2.5 cm)

Unpacking and removing shipping bolts

INSTALLATION INSTRUCTIONS

Remove the bottom two shipping bolts with the wrench

(included) to fully loosen all four shipping bolts by turning them counterclockwise and then pulling them out.

When removing the washer from the carton base, be sure to remove the foam drum support in the middle of the carton base. If you must lay the washer down to remove the base packaging materials, always lay it carefully on its side. DO NOT lay the washer on its front or back.

Foam Tub Support Carton Base

Retainer

Shipping

bolt

Locate the four hole caps included in the accessory pack

and install them in the shipping bolt holes.

Cap

NOTE

• Save the bolt assemblies for future use. To prevent

damage to internal components, DO NOT transport the washer without reinstalling the shipping bolts.

• Failure to remove shipping bolts and retainers may

cause severe vibration and noise, which can lead to permanent damage to the washer. The cord is secured to the back of the washer with a shipping bolt to help prevent operation with shipping bolts in place.

INSTALLATION INSTRUCTIONS

Connecting the water lines

Check the rubber seals on both sides of the hose.

- Insert a rubber seal into the threaded fittings on each hose to prevent leaking.

Connect the hoses to the water inlets tightly by hand and

then tighten another 2/3 turn with pliers.

- Connect the blue hose to the cold water inlet and the red hose to the hot water inlet.

Rubber seal

Water hose (To water inlet on the washing machine)

Connect the water supply hoses to the HOT and COLD

water faucets tightly by hand and then tighten another 2/3 turn with pliers.

- Connect the blue hose to a cold water faucet and the red hose to a hot water faucet.

WARNING

• Do not overtighten. Damage to the coupling can result.

After connecting inlet hose to water faucets, turn on the

water faucets to flush out foreign substances (dirt, sand or sawdust) in the water lines. Let water drain into a bucket, and check the water temperature.

Rubber seal

Water hose (To faucet)

Cold

water

inlet

WARNING

• Do not overtighten the hoses.

Overtightening can damage the valves resulting in leaking and property damage.

Check for leaks by turning on the faucets.

- If water leaks, check steps 1 to 4 again.

NOTE

• For your safety, and for extended product life, use only

authorized components. The manufacturer is not responsible for product malfunction or accidents caused by the use of separately purchased unauthorized parts.

• Use new hoses when you install the washing machine.

Do not reuse old hoses. Use only the inlet hoses provided with the washer. LG does not recommend the use of aftermarket hoses.

• Periodically check the hoses for cracks, leaks and wear,

and replace the hoses every 5 years.

• Do not stretch the water hoses intentionally, and make

sure that they are not crushed by other objects.

• Water supply pressure must be between 14.5 PSI and

116 PSI (100~800 kPa). If the water supply pressure is more than 116 PSI, a pressure reducing valve must be installed.

• To provide optimum washing performance the hot water temperature should be set at 120-135°F (48-57°C) and the cold at 60°F (15°C).

Hot water inlet

Connecting the drain line

INSTALLATION INSTRUCTIONS

Secure the drain hose in place to prevent moving and leaking.

NOTE

• The drain hose should be properly secured. Failure to

properly secure the drain hose can result in flooding and malfunction.

• Total height of the house end should not exceed 96

inches (244.8 cm) from the bottom of the washer.

• The drain must be installed in accordance with any applicable local codes and regulations.

• Make sure that the water lines are not stretched,

pinched, crushed, or kinked.

Using a standpipe

Clip the end of the hose into the elbow bracket.

- Connect the elbow bracket within 4 inches (10 cm) from the end of the drain hose. If the drain hose is extended more than 4 inches (10 cm) beyond the end of the elbow bracket, mold or microorganisms could spread to the inside of the washer.

Using a laundry tub

Clip the end of the hose into the elbow bracket.

- Connect the elbow bracket within 4 inches (10 cm) from the end of the drain hose. If the drain hose is extended more than 4 inches (10 cm) beyond the end of the elbow bracket, mold, or microorganisms could spread to the inside of the washer.

No more than 4 inches (10 cm)

Elbow Bracket

Hang the end of the drain hose over the side of the

laundry tub.

Elbow

Bracket

Laundry Tub

No more than 4 inches (10 cm)

Elbow Bracket

Insert the end of the drain hose into the standpipe.

Elbow Bracket

Drain Hose

max. 96”

(2.4 m)

Drain Hose

Tie Strap

Use a tie strap to secure the drain hose in place.

max. 96”

(2.4 m)

Use a tie strap to secure the drain hose in place.

INSTALLATION INSTRUCTIONS

Leveling the washing machine

The washer tub of your new washing machine spins at very high speeds. To minimize vibration, noise, and unwanted movement, the floor must be perfectly level and solid.

Check the washing machine’s level.

- Check the precise level by rocking the top edges of the washing machine or placing a level on the washing machine. The slope beneath the washing machine must not exceed 1°, and all four leveling feet must rest firmly on the floor.

Turn the lower leveling feet clockwise to level the washing

machine.

- Turning the lower leveling feet clockwise raises the washing machine.

Level

1°

Check the washing machine’s level again.

- Push or rock the top edges of the washing machine gently to make sure that the washing machine does not rock.

- If the washing machine rocks, repeat steps 1 to 3.

WARNING

• Using the washing machine without leveling, it may result in malfunction caused by the production of excess vibration and noise.

• Use the leveling feet only when you level the washing machine. If you raise the leveling feet unnecessarily, it

may cause abnormal vibration of the washing machine.

Using non-skid pads (optional)

If you install the washing machine on a slippery surface, it may move because of excessive vibration. Incorrect leveling may cause malfunction through noise and vibration. In the event of this, lay the non-skid pads under the leveling feet and adjust the level.

Clean the floor to attach the non-skid pads.

- Use a dry rag to remove and clean foreign objects or moisture. If moisture remains, the non-skid pads may slip.

Raise

Turn the locknuts counterclockwise and tighten them

when the washing machine is level.

Tighten all 4 lock

nuts securely using

the wrench.

Adjust the level after placing the washing machine in the

installation area.

Place the adhesive side of the non-skid pad on the floor.

- It is most effective to install the non-skid pads under the front legs. If it is hard to place the pads under the front legs, place them under the back legs.

This side up

Adhesive side

Remove backing

Check the washing machine’s level again.

- Push or rock the top edges of the washing machine gently to make sure that the washing machine does not rock. If the washing machine rocks, level the washing machine again.

PREPARATION

Precautions for fabric care before wash cycle

Read and observe the following to prevent shrinkage or damage to clothes.

PREPARATION

Check all pockets to make sure that they are empty.

-Items such as clips, matches, pens, coins, and keys can damage both your washer and your clothes.

Close zippers, hooks, and drawstrings to prevent these

items from snagging or tangling on other clothes.

Pretreat heavily stained areas before washing.

- Doing so will produce clean, stain-free results.

Combine large and small items in a load. Load large items

first.

Large items should not be more than half of the total

washload.

The washer can be fully loaded, but the drum should not be

tightly packed with items.

-The door of the washer should close easily.

Do not wash single items, except for bulky items such as

blankets. Make sure to wash laundry in similar types of loads.

- Washing a single small item may result in the tub becoming unbalanced, vibrating and making a noise.

Brush heavy soil, dust, or hair off fabrics before washing.

- Laundry may not wash clean if there is dirt or sand on the fabrics, or they may damage due to particles rubbing against sheer fabrics.

Wash blankets individually.

- Washing more than one blanket together may produce unclean results due to tangling or an unbalanced load.

Always separate fabrics according to their colors and wash

them separately to prevent colors from running.

- Fabrics may damage or become stained due to fabric dyes running, or due to foreign objects transferring from one fabric to another.

Do not wash waterproof clothes.

- This may cause abnormal vibration, or may cause the load to bounce, which could damage the tub.

Check if there are any other foreign objects in the door seal

and take extra care that clothes do not get caught there.

- Foreign objects in the door seal may stain clothes, and water may leak if clothes get caught in the door seal.

Wash underwear or small, light items in a laundry net.

- Small, light items may get caught in the door seal, and a brassiere hook may damage other items or the tub.

PREPARATION

Fabric care labels

Most articles of clothing feature fabric care labels that include instructions for proper care.

Category Label Directions

Hand Wash

Machine Wash, Normal Cycle

Use Permanent Press/Wrinkle Resistant washing machine setting (which has a cool down or cold spray before the reduced spin)

Washing

Water Temperature

Use Gentle/Delicate washing machine setting (slow agitation and/ or reduced wash time).

Do Not Wash

Do Not Wring

Hot

Warm

Sorting laundry

It is recommended that you sort laundry into similar loads that are washable in the same cycle. Refer to the following chart for sorting clothes

Colors Whites / Lights / Darks

Soil Heavy / Normal / Light

Fabric Delicates / Easy Care / Sturdy Cottons

Lint Lint Producers / Lint Collectors

Bleach symbols

Cold/Cool

Any Bleach (When Needed)

Only Non-Chlorine Bleach (When Needed)

Do Not Bleach

Using detergent/fabric softener

PREPARATION

Recommended detergent

Make sure to use HE (High-Efficiency) detergent for frontloading washing machines. HE detergents dissolve more efficiently and produce fewer suds to ensure efficient washing and rinsing. Use the correct amount of detergent as indicated on the label of the detergent packaging.

Designed specially to use only HE (High-Efficiency) detergent

NOTE

• Only use HE detergents, since using a regular detergent may produce excessive suds.

• HE detergents produce fewer suds, dissolve more efficiently to improve washing and rinsing performance, and help to keep the interior of your washer clean.

• Use less detergent for soft water.

• Wipe up any spills immediately, as liquids could dam-

age the finish and the control panel of the washing machine.

• Using too much detergent can cause a build-up in the

tub resulting in unsatisfactory performance and ma-

chine malfunction.

• If you use a detergent that does not dissolve easily or a

detergent with high viscosity, it will leave a residue on the tub, which may not rinse properly.

About the dispenser

The automatic dispenser consists of three compartments which hold:

• Liquid chlorine bleach.

• Liquid fabric softener.

• Liquid or powdered detergent and color-safe bleach for main

wash. All laundry products can be added at once in their respective dispenser compartments. They will be dispensed at the appropriate time for the most effective cleaning. After adding the laundry products to the dispenser, close the dispenser drawer.

To add detergent, bleach, and fabric softener to the automatic dispenser:

1. Open the dispenser drawer.

2. Load the laundry products into the appropriate

compartments.

3. Slowly close the dispenser drawer to avoid early dispensing

of the laundry products.

NOTE

• It is normal for a small amount of water to remain in the

dispenser compartments at the end of the cycle.

PREPARATION

Loading the dispenser

Main Wash Detergent Compartment

This compartment holds laundry detergent for the main wash cycle, which is added to the load at the beginning of the cycle. Always use HE (High-Efficiency) detergent with your washing machine. Follow the detergent manufacturer's instructions with respect to the amount of detergent to use, and never use more than the recommended amount. Using too much detergent can result in detergent buildup in clothing and the washer. Either powdered or liquid detergent may be used.

NOTE

• Liquid or powdered color-safe bleach may be added

to the main wash compartment with detergent of the same type.

Designed specially to use only HE (High-Efficiency) detergent

Main Wash Detergent

Compartment

Liquid Bleach Compartment

This compartment holds liquid chlorine bleach, which will be dispensed automatically at the proper time during the wash cycle.

NOTE

• Do not add powdered or liquid color-safe bleach to this

compartment.

• Always follow the manufacturer’s recommendations

when adding bleach. Do not exceed the maximum fill line. Using too much bleach can damage fabrics.

• Never pour undiluted liquid chlorine bleach directly onto

the load or into the drum. Fabric damage can occur.

Fabric Softener Compartment

This compartment holds liquid fabric softener, which will be automatically dispensed during the final rinse cycle.

NOTE

• Always follow the manufacturer’s recommendations

when adding fabric softener. Do not exceed the maximum fill line. Using too much fabric softener may result in stained clothes.

• Dilute concentrated fabric softeners with warm water.

Do not exceed the maximum fill line.

• Never pour fabric softener directly onto the load or into

the drum.

• Do not add the fabric softener sheets to this compartment.

• Do not add ‘fabric sheet softener’ into the dispenser draw as it is likely to cause water to leak out. If ‘fabric

sheet softener’ has been added, please pull out the dispenser draw and remove.

Liquid Chlorine

Bleach Compartment

Liquid Fabric

Softener Compartment

OPERATING YOUR WASHER

1. Ready mode

1) Coin / Card type

– The cycle LEDs flash at the same time, when the

price of cycles are equal.

2) OPL type

– The cycle LEDs is lit at the same time, and displayed

‘PUSH’.

2. Insert card/coin (not for OPL type)

Insert a cash card that has a sufficient balance.

The card balance should be more than the programmed vend price for a selected cycle.

NOTE

• When the card balance is not enough, machine displays the card balance for 5 seconds and then displays

message repetitively

• Insert a sufficient amount of change that is more than

the programmed vend price for the selected cycle.

NOTE

• The machine will not start until sufficient coins are

inserted.

4. Add super wash

Wash time or rinse cycle can be added when additional

coin is inserted or a valid cash card is entered.

5. Change course

You cannot change the course while the machine is

running.

6 . Cycle finish

The machine stops and LED display shows “

with beeper sound.

Do not work any button and stop the washer

❋

(When the washer is operating) or (when a cycle is in progress)

WARNING

• To reduce the risk of fire, electric shock, or injury to

persons, read the IMPORTANT SAFETY INSTRUC- TIONS before operating this appliance.

”

3. Select the cycle

Press the desired button and press the start button.

The display LED will show the remaining time and the selected cycle starts.

• Select cycles designed for different types of fabric and soil

levels.

CYCLE Fabric type

WHITES

COLORS

DELICATES

PERM.

PRESS

Cotton, linen, towels, shirts, sheets

Mixed loads, work clothes, jeans, shirts

Dress shirts, blouses, nylons, sheer or lacey garments

Dress shirts, pants, wrinkle-free clothing, cotton/poly blend clothing, tablecloths

Wash/Rinse

Temp.

Hot/Cold High

Warm/ Cold High

Cold/ Cold Low

Warm/ Cold Medium

Spin

Speed

+ 47 hidden pages