LG F1014NTGW Manual book [id]

OWNER’S MANUAL

WASHING

ENGLISH

BAHASA INDONESIA

MACHINE

Before beginning installation, read these instructions carefully. This will simplify installation and ensure that the product is installed correctly and safely. Leave these instructions near the product after installation for future reference.

F1014NTGW

Registration No. : I.14.LG2.02805.0715

MFL69283913_00

PT. LG ELECTRONICS INDONESIA GANDARIA 8 OFFICE TOWER LT.29 BC& 31 ABCD JL. SULTAN ISKANDAR MUDA, KEBAYORAN LAMA UTARA-KEBAYORAN LAMA, JAKARTA SELATAN - DKI JAKARTA RAYA, 12240, INDONESIA

www.lg.com

TABLE OF CONTENTS

SAFETY INSTRUCTIONS ......................................03

Important Safety Instructions ............................................................... 05

INSTALLATION .......................................................08

Specifications ......................................................................................08

Accessories .........................................................................................08

Installation Place Requirements .......................................................... 09

Unpacking and Removing Shipping Bolts ...........................................10

Using Non-Skid Pads (Optional).......................................................... 11

Wooden Floors (Suspended Floors) .................................................... 11

Leveling the Washing Machine ............................................................12

Connecting Inlet Hose .........................................................................12

Installation of Drain Hose ....................................................................15

Electrical Connections (In the UK Only) .............................................. 15

This manual is produced for a group of products and may contain images or content different from the model you purchased.

This manual is subject to revision by the manufacturer.

OPERATION ...........................................................16

Using the Washing Machine ................................................................16

Sorting Iaundry ....................................................................................17

Adding Cleaning Products ................................................................... 18

Control Panel ....................................................................................... 20

Washing Programme ...........................................................................21

Option Cycle ........................................................................................ 24

Using Smart Function (Optional) ......................................................... 27

MAINTENANCE ......................................................28

Cleaning your Washing Machine .........................................................28

Cleaning the Water Inlet Filter .............................................................28

Cleaning the Drain Pump Filter ...........................................................29

Cleaning the Dispenser Drawer...........................................................30

Tub Clean (Optional) ...........................................................................30

Caution on Freezing During Winter ..................................................... 31

Using the Smart Diagnosis™ Function ...............................................33

TROUBLESHOOTING ............................................34

Diagnosing Problems ..........................................................................34

Error Messages ...................................................................................36

WARRANTY ............................................................38

ENGLISH

SAFETY INSTRUCTIONS

The following safety guidelines are intended to prevent unforeseen risks or damage from unsafe or incorrect operation of the product.

The guidelines are separated into ‘WARNING’ and ‘CAUTION’ as described below.

This symbol is displayed to the indicate matters and operations that can cause risk. Read the part with this symbol carefully and follow the instructions in order to avoid risk.

WARNING

can cause serious injury or death.

CAUTION

can cause the minor injury or damage the product.

- This indicates that the failure to follow the instructions

WARNING

To reduce the risk of re, electric shock, or injury to persons when using

your product, basic safety precautions should be followed, including the following.

CHILDREN IN THE HOUSEHOLD

This appliance is not intended for use by persons (including children) with reduced physical, sensory or mental capabilities, or lack of experience and knowledge, unless they have been given supervision or instruction concerning use of the appliance by a person responsible for their safety. Children should be supervised to ensure that they do not play with the appliance.

For use in Europe:

This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

Children of less than 3 years should be kept away unless continuously supervised.

GROUNDING REQUIREMENTS

WARNING

For your safety, the information in this manual must be followed to

minimize the risk of re, explosion, or electric shock, or to prevent

property damage, injury to persons, or death.

•This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current.

•This appliance is equipped with a cord having an equipment-grounding conductor and grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

•Improper connection of the equipment-grounding conductor can result in risk of electric

shock. Check with a qualied electrician or service person if you are in doubt as to

whether the appliance is properly grounded.

•Do not modify the plug provided with the appliance. If it does not t the outlet, have a

proper outlet installed by a qualied electrician.

DISPOSAL OF YOUR OLD APPLIANCE

1. All electrical and electronic products should be disposed of separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

2. The correct disposal or your old appliance will help prevent potential negative consequences for the environment and human health.

3. For more detailed information about disposal of your old appliance, please

contact your city ofce, waste disposal service or the shop where you

purchased the product.

ENGLISH

Important Safety Instructions

WARNING

To reduce the risk of re, electric shock, or injury to persons when using

your product, basic safety precautions should be followed, including the following.

Installation

•Never attempt to operate this appliance if it is damaged, malfunctioning, partially disassembled, or has missing or broken parts, including a damaged cord or plug. It can cause electric shock or injury.

•This appliance is heavy. Two or more people may be needed to install and move the appliance. Failure to do so can result in injury.

•Store and install this appliance where it will not be exposed to temperatures below freezing or exposed to outdoor weather conditions. Failure to do so can result in leakage.

•Tighten the drain hose to avoid separation. Splashing of water may cause electric shock.

Operation

•Do not use a sharp object like drill or pin to press or separate an operation unit. It can cause the electric shock or injury.

•Only an authorized repair person from LG Electronics service centre should disassemble, repair, or modify the product. Improper service may cause

injury, electric shock or re.

•Do not spray the water inside or outside the product to clean it. Water can damage the insulation, causing electric

shock or re.

•Keep the area underneath and around your appliances free of combustible materials such as lint, paper, rags, chemicals, etc. Improper use can cause

re or explosion.

•If the supply cord is damaged, it must be replaced by the manufacturer or

its service agents or similarly qualied

person in order to avoid a hazard.

•The appliance must not be installed behind a lockable door, a sliding door or a door with a hinge on the opposite side to that of the tumble dryer, in such a way that a full opening of the tumble dryer door is restricted.

•Do not put living animals, such as pets into the product. It may cause injury.

•Do not leave this appliance door open. Children may hang on the door or crawl inside the appliance, causing damage or injury.

•Never reach into this appliance while it is operating. Wait until the drum has completely stopped. Failure to do so may result in injury.

•Do not put in, wash or dry articles that have been cleaned in, washed in, soaked in, or spotted with combustible or explosive substances (such as wax, oil, paint, gasoline, degreasers, drycleaning solvents, kerosene, vegetable oil, cooking oil, etc.). Improper

use can cause re or explosion.

•In case of ood, stop using the product and contact the LG Electronics service centre. Contact with water can cause electric shock.

•If the drain hose or inlet hose is frozen during winter, use it only after thawing.

Freezing may cause re or electric

shock, and frozen parts may cause product malfunction or reduction in product life span.

•Keep all washing detergents, softener and bleach away from children. These products contain poisonous materials.

•Do not plug multiple products into multiple socket-outlets or extension

cords. This can cause re.

•Remove the power plug when you clean the product. Not removing the plug may result in electric shock or injury.

•Do not push down the door excessively, when the appliance door is open. Doing so may topple over the appliance and it can cause the injury.

•Use new hose-sets supplied with the appliance. Old hose-sets should not be reused. Water leakage may cause property damage.

•Do not touch the door during steam cycles, drying or high-temperature washing. The door surface can become very hot. Allow the door lock to release before opening the door. Failure to do so may result in injury.

•Do not use inammable gas and combustible substances (benzene, gasoline, thinner, petroleum, alcohol, etc.) around the product. It may cause

explosion or re.

•Do not touch the power plug with wet hands. It can cause the electric shock or injury.

•When pulling out the power plug from an outlet, hold the power plug, not the cable. Damage of the cable can cause the electric shock or injury.

•Do not bend the power cable excessively or place a heavy object on top of it. Damage of the power cable

can cause electric shock or re.

ENGLISH

Technical Safety for Using the Tumble Dryer

•Do not dry unwashed items in the appliance.

•Items that have been soiled with substances such as cooking oil, vegetable oil, acetone, alcohol, petrol, kerosene, spot removers, turpentine, waxes and wax removers should be washed in hot water with an extra amount of detergent before being dried in the appliance.

•Fabric softeners or other similar products should be used according to the fabric softener instructions.

•Remove all objects from pockets such as lighters and matches.

Disposal

•Before discarding an old appliance, unplug it. Render the plug useless. Cut off the cable directly behind the appliance to prevent misuse.

•Dispose of the packaging material (such as vinyl and styrofoam) away from children. The packaging material can suffocate a child.

•Remove the door to the washing compartment before this appliance is removed from service or discarded to avoid the danger of children or small animals getting trapped inside. Failure to do so can result in serious injury to persons or death.

•Never stop this appliance before the end of the drying cycle unless all items are quickly removed and spread out so that the heat is dissipated.

•This appliance is not to be used if industrial chemicals have been used for cleaning.

•Items such as foam rubber (latex foam), shower caps, waterproof textiles, rubber backed articles and clothes or pillows

tted with foam rubber pads should not

be dried in this appliance.

INSTALLATION

Specications

Transit bolts

Power plug

Drawer

Control panel

Drum

Door

Drain hose

Drain plug

Drain pump lter

Cover cap

(Location may vary depending on products)

Adjustable feet

•Power supply : 220 V~, 50 Hz

•Size : 645 mm (W) x 770 mm (D) x 940 mm (H)

•Product weight : 81 kg

•Wash Capacity : 14 kg

•Permissible water pressure : 0.1–1.0 Mpa (1.0–10.0 kgf/cm

)

•Appearance and specications may vary without notice to improve the quality of the product.

Accessories

Inlet hose (1EA) (※ Option : Hot /

Cold (2EA))

Spanner Elbow Bracket

(for securing drain

hose)

Anti–slip sheets

(2EA)

(Optional)

Caps for covering

shipping bolt holes

Tie strap

ENGLISH

Installation Place Requirements

Location

10 cm 2 cm 2 cm

Level oor : Allowable slope under the entire washing machine is 1°.

Power outlet : Must be within 1.5 meters of either side of the location of the washing machine.

•Do not overload the outlet with more than one appliance.

Additional Clearance : For the wall, 10 cm: rear /2 cm: right & left side

•Do not place or store laundry products on top of the washing machine at any time.

•These products may damage the nish or controls.

Positioning

•Install the washing machine on a at hard oor.

•Make sure that air circulation around the washing machine is not impeded by carpets, rugs, etc.

•Never try to correct any unevenness in the oor with pieces of wood, cardboard or similar materials under the washing machine.

•If it is impossible to avoid positioning the washing machine next to a gas cooker or coal burning insulation (85x60 cm) covered with aluminum foil on the side facing the cooker or stove must be inserted between the two appliances.

•Do not install your washing machine in rooms where freezing temperatures may occur. Frozen hoses may burst under pressure. The reliability of the electronic control unit may be impaired at temperatures below freezing point.

•Please ensure that when the washing machine is installed, it is easily accessible for an engineer in the event of a breakdown.

•With the washing machine installed, adjust all four feet using the transit bolt spanner provided to ensure the appliance is stable, and a clearance of approximately 20 mm is left between the top of the washing machine and the underside of any work-top.

•This equipment is not designed for maritime use or for use in mobile installations such as caravans, aircraft etc.

Electrical Connection

•Do not use an extension cord or double adapter.

•Always unplug the washing machine and turn off the water supply after use.

•Connect the washing machine to an earthed socket in accordance with current wiring regulations.

•The washing machine must be positioned so that the plug is easily accessible.

•Repairs to the washing machine must only be carried

out by qualied personnel. Repairs carried out by

inexperienced persons may cause injury or serious malfunctioning. Contact your local service centre.

•If the washing machine is delivered in winter and temperatures are below freezing, place the washing machine at room temperature for a few hours before putting it into operation.

Unpacking and Removing Shipping Bolts

Lift the washing machine off the foam base.

•After removing the carton and shipping material, lift the washing machine off the foam base. Make sure the tub support comes off with the base and is not stuck to the bottom of the washing machine.

•If you must lay the washing machine down to remove the carton base, always protect the side of the washing machine and lay it carefully on its side. DO NOT lay the washing machine on its front or back.

Install the hole caps.

•Locate the hole caps included in the accessory pack and install them in the shipping bolt holes.

Cap

NOTE

•Save the bolt assemblies for future use. To prevent damage to internal components, DO NOT transport the washing machine without reinstalling the shipping bolts.

•Failure to remove shipping bolts and retainers may cause severe vibration and noise, which can lead to permanent damage to the washing machine. The cord is secured to the back of the washing machine with a shipping bolt to help prevent operation with shipping bolts in place.

Tub Support

(Optional)

Remove the bolt assemblies.

•Starting with the bottom two shipping bolts, use the spanner (included) to fully loosen all shipping bolts by turning them counterclockwise. Remove the bolt assemblies by wiggling them slightly while pulling them out.

Shipping

bolt

Carton base

Retainer

ENGLISH

Using Non-Skid Pads (Optional)

Wooden Floors (Suspended

If you install the washing machine on a slippery surface, it may move because of excessive vibration. Incorrect leveling may cause malfunction through noise and vibration. If this occurs, install the non-skid pads under the leveling feet and adjust the level.

Clean the oor to attach the non-skid pads.

•Use a dry rag to remove and clean foreign objects and moisture. If moisture remains, the non-skid pads may slip.

Adjust the level after placing the washing machine

in the installation area.

Place the adhesive side of the non-skid pad on the

oor.

•It is most effective to install the non-skid pads

under the front legs. If it is difcult to place the

pads under the front legs, place them under the back legs.

This side up

Adhesive side

Floors)

•Wooden oors are particularly susceptible to vibration.

•To prevent vibration we recommend you place rubber cups at least 15 mm thick of the each foot of the

washing machine, secured to at least two oor beams

with screws.

Rubber Cup

•If possible install the washing machine in one of the

corners of the room, where the oor is more stable.

•Fit the rubber cups to reduce vibration.

•You can obtain rubber cups (p/no.4620ER4002B) from the LG Service Centre.

NOTE

•Proper placement and leveling of the washing machine will ensure long, regular, and reliable operation.

•The washing machine must be 100% horizontal

and stand rmly in position.

•It must not ‘Seesaw’ across corners under the load.

•The installation surface must be clean, free from

oor wax and other lubricant coatings.

•Do not let the feet of the washing machine get wet. Failure to do so may cause vibration or noise.

Ensure the washing machine is level.

•Push or rock the top edges of the washing machine gently to make sure that the washing machine does not rock. If the washing machine rocks, level the washing machine again.

Leveling the Washing Machine

Connecting Inlet Hose

If the oor is uneven, turn the adjustable feet as required

(Do not insert pieces of wood etc. under the feet). Make

sure that all four feet are stable and resting on the oor

and then check that the appliance is perfectly level (Use a spirit level).

•Once the washing machine is level, tighten the lock nuts up towards the base of the washing machine. All lock nuts must be tightened.

Raise

Lock Nut

Lower

Tighten all 4

locknuts securely

•Diagonal Check When pushing down the edges of the washing machine top plate diagonally, the washing machine should not move up and down at all (Check both directions). If the washing machine rocks when pushing the machine top plate diagonally, adjust the feet again.

NOTE

•Timber or suspended type ooring may contribute to excessive vibration and unbalance.

•If the washing machine is installed on a raised platform, it must be securely fastened in order to eliminate the risk of falling off.

•Water supply pressure must be between 0.1 MPa and

1.0 MPa (1.0–10.0 kgf/cm

•Do not strip or crossthread when connecting inlet hose to the valve.

•If the water supply pressure is more than 1.0 MPa, a decompression device should be installed.

•Periodically check the condition of the hose and replace the hose if necessary.

Checking Rubber Seal Inlet Hose

Two rubber seals are supplied with the water inlet hoses. They are used for preventing water leaks. Make sure the

connection to taps is sufciently tight.

Hose connector

Rubber seal

Hose connector

Rubber seal

ENGLISH

Connecting Hose to Water Tap

Connecting screw-type hose to tap with thread

Screw the hose connector onto the water supply tap.

Connecting screw-type hose to tap without

thread

Loose the four xing screws.

Upper

connector

Rubber seal

Push the inlet hose vertically upwards so that the

rubber seal within the hose can adhere completely to the tap and then tighten it by screwing it to the right.

Plate

Inlet hose

Connecting one touch type hose to tap without

thread

Unscrew the adapter ring plate and loose the four

xing screws.

Fixing screw

Push the adapter onto the end of the tap so that

the rubber seal forms a watertight connection.

Tighten the four xing screws.

Ring plate

Remove the guide plate if the tap is too large to t

the adapter.

Guide plate

Push the adapter onto the end of the tap so that

the rubber seal forms a watertight connection.

Tighten the adapter ring plate and the four xing

screws.

Pull the connector latch plate down, push the inlet

hose onto the adapter, and release the connector latch plate. Make sure the adapter locks into place.

Latch plate

Connecting Hose to Washing Machine

Make sure that there are no kinks in the hose and that they are not crushed.

When your washing machine has two valves.

•The Inlet hose with the red connector is for the hot water tap.

NOTE

•After completing connection, if water leaks from the hose, repeat the same steps. Use the most conventional type of tap for the water supply. In case the tap is square or too big, remove the guide plate before inserting the tap into the adaptor.

NOTE

•After connecting the inlet hose to the water

tap, turn on the water tap to ush out foreign

substances (dirt, sand, sawdust, etc.) in the water lines. Let the water drain into a bucket, and check the water temperature.

Using the horizontal tap

Horizontal tap

Extension tap

Square tap

ENGLISH

Installation of Drain Hose

Electrical Connections (In the UK

•The drain hose should not be placed higher than 100

cm above the oor. Water in the washing machine

may not drain or may drain slowly.

•Securing the drain hose correctly will protect the oor from damage due to water leakage.

•If the drain hose is too long, do not force it back into the washing machine. This will cause abnormal noise.

about 100 cm

about 145 cm

max. 100 cm

about 105 cm

•When installing the drain hose to a sink, secure it tightly with string.

•Securing the drain hose correctly will protect the oor from damage due to water leakage.

Laundry tub

Hose

retainer

Only)

The wires in the mains lead are coloured in accordance with the following code:

Green and Yellow: Earth

Blue: Neutral

Brown: Live

This appliance must be earthed.

Green and

Yellow (Earth)

Brown (Live)

Blue (Neutral)

As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows:

The green and yellow wire must be connected to the terminal in the plug which is marked with the letter E or

by the earth symbol (

) or coloured Green or Green

and Yellow.

The blue wire must be connected to the terminal which is marked with the letter N or coloured Black.

The brown wire must be connected to the terminal which is marked with the letter L or coloured Red.

If a 13 amp (BS 1363) plug is used, t a 13 amp BS

1362 fuse.

Fuse

Cord grip

max. 100 cm

Tie strap

max. 100 cm

OPERATION

Using the Washing Machine

Before the rst wash, select a cycle (Cotton 60 °C, add

a half load of detergent), allow the washing machine to wash without clothing. This will remove residue and water from the drum that may have been left during manufacturing.

Sort laundry and load items.

•Sort laundry by fabric type, soil level, colour and load size as needed. Open the door and load items into the washing machine.

Add cleaning products and/or detergent and

softener.

•Add the proper amount of detergent to the detergent dispenser drawer. If desired, add bleach or fabric softener to the appropriate areas of the dispenser.

Choose the desired washing cycle.

•Press the cycle button repeatedly or turn the cycle selector knob until the desired cycle is selected.

Begin cycle.

•Press the Start/Pause button to begin the cycle.

The washing machine will agitate briey without

water to measure the weight of the load. If the Start/Pause button is not pressed within 5 minutes, the washing machine will shut off and all settings will be lost.

End of cycle.

•When the cycle is nished, a melody will sound. Immediately remove your clothing from the washing machine to reduce wrinkling. Check around the door seal when removing the load for small items that may be caught in the seal.

Turn on the washing machine.

•Press the Power button to turn ON the washing machine.

ENGLISH

Sorting Iaundry

Look for a care label on your clothes.

•This will tell you about the fabric content of your garment and how it should be washed.

•Symbols on the care labels.

Wash temperature

Normal machine wash

Permanent press

Delicate

Hand wash

Do not wash

Caring before loading.

•Combine large and small items in a load. Load

large items rst.

•Large items should not be more than half the total wash load. Do not wash single items. This may cause an unbalanced load. Add one or two similar items.

•Check all pockets to make sure that they are empty. Items such as nails, hair clips, matches, pens, coins and keys can damage both your washing machine and your clothes.

Sorting laundry.

•To get the best results, sort clothes into loads that can be washed with the same wash cycle.

•Different fabrics need to be washed at varying temperatures and spin speeds.

•Always sort dark colours from pale colours and whites. Wash separately as dye and lint transfer can occur causing discolouration of white and pale garments. If possible, do not wash heavily soiled items with lightly soiled ones.

– Soil (Heavy, Normal, Light)

Separate clothes according to amount of soil.

– Colour (White, Lights, Darks)

Separate white fabrics from coloured fabrics.

– Lint (Lint producers, Collectors)

Wash lint producers and lint collectors separately.

•Close zippers, hooks and strings to make sure that these items don’t snag on other clothes.

•Pre-treat dirt and stains by brushing a small amount of detergent dissolved water onto stains to help lift dirt.

•Check the folds of the exible gasket (gray) and remove any small articles.

•Check inside the drum and remove any items from a previous wash.

•Remove any clothing or items from the exible gasket to prevent clothing and gasket damage.

Adding Cleaning Products

Detergent Dosage

•Detergent should be used according to the instruction of the detergent manufacturer and selected according to type, colour, soiling of the fabric and washing temperature.

•If too much detergent is used, too many suds can occur and this will result in poor washing results or cause heavy load to the motor.

•If you wish to use liquid detergent follow the guidelines provided by the detergent manufacturer.

•You can pour liquid detergent directly into the main detergent drawer if you are starting the cycle immediately.

•Do not use liquid detergent if you are using Time delay, or if you have selected Pre Wash, as the liquid may harden.

•If too many suds occur, reduce the detergent amount.

•Detergent usage may need to be adjusted for water temperature, water hardness, size and soil level of the load. For best results, avoid oversudsing.

•Refer to the label of the clothes, before chooseing the detergent and water temperature:

•When using the washing machine, use designated detergent for each type of clothing only:

– General powdered detergents for all types of fabric

– Powdered detergents for delicate fabric

– Liquid detergents for all types of fabric or

designated detergents only for wool

•For better washing performance and whitening, use detergent with the general powdered bleach.

•Detergent is ushed from the dispenser at the beginning of the cycle.

NOTE

•Do not let the detergent harden. Doing so may lead to blockages, poor rinse performance or odour.

•Full load : According to manufacturer’s recommendation.

•Part load : 3/4 of the normal amount

•Minimum load : 1/2 of full load

Adding Detergent and Fabric Softener

Adding detergent

•Main wash only →

•Pre wash+Main wash →

NOTE

•Too much detergent, bleach or softener may

cause an overow.

•Be sure to use the appropriate amount of detergent.

Adding fabric softener

•Do not exceed the maximum ll line. Overlling can cause early dispensing of the fabric softener, which may stain clothes. Close the dispenser drawer slowly.

ENGLISH

•Do not leave the fabric softener in the detergent drawer for more than 2 days (Fabric softener may harden).

•Softener will automatically be added during the last rinse cycle.

•Do not open the drawer when water is being supplied.

•Solvents (benzene, etc) should not be used.

NOTE

•Do not pour fabric softener directly on the clothes.

Adding water softener

•A water softener, such as Anti-limescale (e.g. Calgon) can be used to cut down on the use of detergent in extremely hard water areas. Dispense according to

the amount specied on the packaging. First add

detergent and then the water softener.

•Use the quantity of detergent required for soft water.

Using tablet

Open the door and put tablets into the drum.

Load the laundry into the drum and close the door.

Control Panel

Power button

•Press the Power button to turn the washing machine on.

•Press and hold the Power button for 1 second to turn the washing machine off.

Start/Pause button

•This Start/Pause button is used to start the wash cycle or pause the wash cycle.

•If a temporary stop of the wash cycle is needed, press the Start/Pause button.

Display

•The display shows the settings, estimated time remaining, options, and status messages. When the product is turned on, the default settings in the display will illuminate.

•The display shows estimate time remaining. While the size of the load is being calculated automatically, blinking appears.

or ‘Detecting’

Programme dial

•Programmes are available according to laundry type.

•Lamp will light up to indicate the selected programme.

Options

•This allows you to select an additional cycle and will light when selected.

•Use these buttons to select the desired cycle options for the selected cycle.

ENGLISH

Washing Programme

Programme table

Programme Description Fabric Type

Coloured fast garments (shirts,

Cotton

Heavy Duty

Baby care

Hygiene Washes laundry in a hot cycle

Sports Wear

Wool

Speed Wash

Provides better performance by combining various drum motions.

This cycle is for washing heavily soiled laundry though more powerful tub rotation.

Removes solid and protein stains, provides better rinse performance.

This cycle is suitable for sports wear such as jogging clothes and running wear.

Enables to wash wool fabrics. (Please use detergent for machinewashable woolens).

This cycle provides a fast washing time for small loads and lightly soiled clothes.

nightdresses, pajamas, etc) and normally soiled cotton load (underwear).

Heavily soiled Cotton Fabrics

Lightly soiled baby wear. 60 °C

Cotton, underwear, pillow covers, bed sheets, baby wear.

coolmax, gore-tex, eece and

sympatex

Machine washable woolens with pure now wool only

Coloured laundry which is lightly soiled fast. CAUTION : Use less than 20 g of detergent (for 2.0 kg load) otherwise detergent may remain on the clothes.

Proper

Temp.

40 °C

(Cold to

60 °C)

60 °C

(40 °C to

60 °C)

95 °C

30 °C

(Cold to

30 °C)

40 °C

(Cold to

40 °C)

Maximum

Load

Rating

Less than

3.0 kg

Less than

5.0 kg

Less than

3.0 kg

Less than

5.0 kg

Less than

4.0 kg

Less than

5.0 kg

Silent

Dark Wash

Duvet

Provides less noise and vibration and saves money by using overnight electricity.

If it's possible for clothes to decolourate, please use this cycle. The cycle prevent decolorization. (Please use detergent for colored fabrics.)

This cycle is for large items such as bed covers, pillows, sofa covers, etc.

Color fast garments (shirts, nightdresses, pajamas, etc) and lightly soiled white cotton (underwear).

Dark garments made from cotton or mixed fabrics.

Cotton bedding except special garments (delicates, wool, silk, etc.)

with lling: duvets, pillows, blankets, sofa covers with light lling

40 °C

(Cold to

60 °C)

30 °C

(Cold to

40 °C)

Cold

(Cold to

40 °C)

Less than

5.0 kg

Less than

5.0 kg

1 king size

Programme Description Fabric Type

Proper

Temp.

Maximum

Load

Rinse+Spin

Download

Cycle

Use for laundry that need rinsing only of to add rinse-added fabric softener to laundry

For downloadable cycles. If you did not download any cycles, the default is Cold Wash.

Normal fabrics which can be washable

Choice

Less than

3.0 kg-

•Water Temperature: Select the appropriate water temperature for chosen wash cycle. Always follow garment manufacturer’s care label or instructions when washing.

NOTE

•Neutral detergent is recommended.

ENGLISH

Extra Options

Programme

Cotton

Heavy Duty

Baby care

Hygiene

Sports

Wear

Wool

Speed

Wash

Silent

Dark Wash

Duvet

Rinse+Spin

Time

Delay

Turbo

Wash™

Custom

PGM

Crease

Care

Soak

Pre

Wash

Intensive Normal Light

● ●** ● ● ● ● ● ● ● ●

● ● ● ● ● ● ● ● ●

● ● ● ● ● ●

● ● ● ● ● ● ●

● ● ● ● ● ●

● ● ● ●

● ●** ● ● ●

● ● ● ● ● ● ● ● ●

● ● ● ● ● ●

● ● ● ●

Add

Load

** : This option is automatically included in the cycle and can be deleted.

Option Cycle

Add Load

Time Delay

You can set a time delay so that the washing machine

will start automatically and nish after a specied time

interval.

Press the Power button.

Select a washing programme.

Press the Time Delay button and set time required.

Press the Start/Pause button.

NOTE

•The delay time is the time to the end of the programme, not the start. The actual running time may vary due to water temperature, wash load and other factors.

Turbo Wash™

Wash cycle in under 1 hour with energy and water saving. (based on half of laundry)

Press the Power button.

Use this function to add loads or remove the foreign material.

Press the Add Load button.

Close the door after add loads or remove the

foreign material (e.g. coin or pin etc.)

Press the Start/Pause button.

•Results when choosing Add Load during cycles.

– When the tub is spinning : Tub stops and Door

Lock is off.

– When water temperature in the tub is higher

than 45 °C : Add Load is not available with short warning sound for safety.

– When lots of water is in the tub : Door Lock is off

after draining by safe water level.

NOTE

•Open the door when Door Lock is off after checking the safety.

•Add Load doesn't work when Tub Cleaning course is in progress for safety.

•Put the laundry into the tub completely. Laundry caught in between door closing part can damage door packing (rubber part) and might cause failure.

Select a washing programme.

Press the Turbo Wash™ button.

Press the Start/Pause button.

NOTE

•Turbo Wash™ function of Some courses is selected automatically.

Crease Care

If you want to prevent creasing, select Crease Care option.

Press the Power button.

Select a washing programme.

Touch the Crease Care button.

Press the Start/Pause button.

ENGLISH

Custom PGM

Rinse

Custom PGM allows you to store a customized wash cycle for future use.

Press the Power button.

Select a washing programme.

Select the cycle (Washing method, number of

rinses, spin speed, water temperature etc.).

Press and hold the Custom PGM button for 3

seconds.

The Custom PGM is now stored for future use.

To reuse the programme, select Custom PGM and press the Start/Pause button.

Wash

Soak

Use this mode to wash normal clothes or thick and

heavy clothes which are excessively dirty.

By pressing the Rinse button the Rinse times can be selected.

•1 / 2 / 3 / 4 / 5 (times)

Spin

•Spin speed level can be selected by pressing the Spin button repeatedly.

– Extra High / High / Medium / Low / Extra Low

•Spin Only

Press the Power button.

Press the Spin button to select RPM.

Press the Start/Pause button.

NOTE

•When you select ‘No Spin’, it will still rotate for a short time to drain quickly.

Pre Wash

If the laundry is heavily soiled, the Pre Wash cycle is recommended.

Intensive

If the laundry is normal and heavily soiled, the Intensive option is effective.

Normal

This option is automatically selected in every course

except for Rinse+Spin.

Light

This cycle is suitable for lightly soiled clothing.

Temp.

The Temp. button selects the wash and rinse temperature combination for the selected cycle. Press this button until the desired setting is lit. All rinses use cold tap water.

•Select the water temperature suitable for the type of load you are washing. Follow the garment fabric care labels for best results.

Child Lock ( )

Select this function to lock the buttons on the control assembly to prevent tampering.

Locking the control panel

Press and hold the Child Lock button for 3

seconds.

A beeper will sound, and ‘ ’ will appear on the

display.

When the child lock is set, all buttons are locked except the Power button.

NOTE

•Turning off the power will not reset the child lock function. You must deactivate child lock before you can access any other functions.

Unlocking the control panel

Press and hold the Child Lock button for 3 seconds.

•A beeper will sound and the remaining time for the current programme will reappear on the display.

+ 58 hidden pages