ENGLISH
LED LCD MONITOR
Please read this manual carefully before operating your set and retain it for future reference.
LED LCD MONITOR MODELS
E1951S E1951T E2251VR E2251VQ
E2051S E2051T E2351VR E2351VQ
E2251S E2251T
E2351T
www.lg.com
ENGLISH
2 TABLE OF CONTENTS
3 |
ASSEMBLING AND PREPAR- |
|
27 PROPER POSTURE |
|
ING |
|
27 Proper posture for using the Monitor set. |
3 |
Unpacking |
|
|
|
|
||
4 |
Parts and buttons |
|
28 LICENSES |
6 |
Setting up the Monitor set |
|
|
|
|
||
6 |
- Attaching the Stand Base |
|
|
6 |
- Detaching the Stand Base |
|
|
6 |
- Detaching the Stand Body (Using the |
|
|
|
Wall mount) |
|
|
7 |
- Mounting on a table |
|
|
8 |
- Mounting on a wall |
|
|
10 USING THE MONITOR SET
10Connecting to a PC
10- D-SUB connection
11- DVI-D connection
12- HDMI connection
13CUSTOMIZING SETTINGS
13Accessing The Main Menus
14Customizing Settings
14- Menu Settings
15- SUPER ENERGY SAVING Settings
16- SUPER+ RESOLUTION Settings
16- Volume Settings (Only supported in HDMI)
17- DUAL MONITOR Settings
17- DUAL WEB Settings
18TROUBLESHOOTING
20 SPECIFICATIONS
25Preset Modes (Resolution)
25- D-SUB / DVI Timing
26- HDMI Timing
26 Indicator
ASSEMBLING AND PREPARING 3
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.
ENGLISH
CD(Owner's Manual) / |
D-SUB Cable |
Card |
(This signal cable may be attached |
|
to this product before shipping out.) |
DVI-D Cable
(This cable is not included in all countries.)
Power Cord |
AC-DC Adapter |
Stand Base |
CAUTION
yyDo not use any unapproved accessories to ensure the safety and product life span.
yyAny damages or injuries by using unapproved accessories are not covered by the warranty.
NOTE
yyThe accessories supplied with your product may vary depending on the model.
yyProduct specifications or contents in this manual may be changed without prior notice due to upgrade of product functions.
yUser should use shielded signal interface cables (RGB cable / DVI-D cable) with ferrite cores (core in the connector) to maintain standard compliance for the product.
4 ASSEMBLING AND PREPARING
ENGLISH
Power Indicator yyLighting On: Turned on yyLighting Off: Turned off
(Power Button)
Button ("CUSTOMIZING
SETTINGS" on page 13)
|
E2251VR |
E2251VQ |
E1951S E2051S E2251S |
E2351VR |
E2351VQ |
DC-IN / |
HDMI |
|
D-SUB |
|
|
|
|
DC-IN / |
|
DVI-D |
D-SUB |
E1951T E2051T
E2251TE2351T
DC-IN /
DVI-D D-SUB
Connection panel (See p.10)
|
|
ASSEMBLING AND PREPARING 5 |
|
|
|
|
|
Button |
|
Description |
|
MENU |
Accesses the main menus.(See p.14) |
||
|
|
|
|
Left First Button |
OSD LOCKED/ |
This function allows you to lock the current control settings, so |
|
|
UNLOCKED |
that they cannot be inadvertently changed. |
|
|
|
Press and hold the Left First Button for several seconds. |
|
|
|
The message "OSD LOCKED" should appear. |
|
|
|
You can unlock the OSD controls at any time by pushing the |
|
|
|
Left First Button for several seconds. The message "OSD |
|
|
|
UNLOCKED" should appear. |
|
SUPER+ RESOLUTION |
Use this button to enter the SUPER+ RESOLUTION menu. For more information.(See p.16) |
||
DUAL |
Use this button to enter the DUAL menu. |
||
|
For more information.(See p.17) |
||
AUTO |
When adjusting your display settings, first press the AUTO button on the MONITOR |
||
|
SETUP OSD. (Only supported in Analog Mode) |
||
|
The best display mode |
|
|
|
E1951S / E1951T |
1366 x 768 |
|
|
E2051S / E2051T |
1600 x 900 |
|
|
|
|
|
|
E2251S / E2251T |
1920 x 1080 |
|
|
E2251VR / E2251VQ |
|
|
|
E2351T / E2351VR |
|
|
|
E2351VQ |
|
|
VOLUME (Only HDMI mode) E2251VR / E2351VR / E2251VQ / E2351VQ
|
Adjust the volume of the Monitor set.(See p.16) |
|
INPUT |
You can choose the input signal. |
|
|
yy When two input signals are at least are connected, you can select the input signal |
|
|
(D-SUB/DVI/HDMI) you want. |
|
|
yy When only one signal is connected, it is automatically detected. The default setting is |
|
|
D-SUB. |
|
EXIT |
Exit the OSD(On Screen Display). |
|
|
|
|
(Power Button) |
Turns the power on or off. |
|
|
Power Indicator |
The power indicator stays blue if the display is running |
|
|
properly (On Mode). If the display is in Sleep Mode, the power |
|
|
indicator blinks blue. |
ENGLISH
ENGLISH
6 ASSEMBLING AND PREPARING
1 Place the monitor's screen face down.
CAUTION
yyTo protect the screen from scratches, cover the surface with a soft cloth.
2Check the position (at the front and rear) of the stand body, then mount the stand base on the stand body as shown in the figure.
Stand Body
Stand Base
3Using a coin, turn the screw clockwise to secure the stand base.
1Place the monitor's screen face down.
To protect the screen from scratches, cover the surface with a soft cloth.
2Using a coin, turn the screw in the stand base counterclockwise. Detach the stand base from
the stand body.
Stand Body
Stand Base
CAUTION
yyThis illustration depicts the general model of connection. Your monitor may differ from the items shown in the picture.
yyDo not carry the product upside down holding only the stand base. The product may fall and get damaged or injure your foot.
Stand Base
ASSEMBLING AND PREPARING 7
Detaching the Stand Body (Using the Wall mount)
1Remove 2 screws and pull out the Hinge Cover from the Monitor set.
1Lift and tilt the Monitor set into its upright position on a table.
Leave a 10 cm (minimum) space from the wall for proper ventilation.
10 cm
10 cm
10 cm
10 cm
ENGLISH
2 Remove 4 screws and pull out the Stand Body |
2 Connect the AC-DC Adapter and Power Cord |
from the Monitor set. |
to a wall outlet. |
DC-IN /
3 Press Power button on the front switch of panel to turn the power on.
CAUTION
Disconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur.
ENGLISH
8 ASSEMBLING AND PREPARING
WARNING |
manual supplied with the Kensington security |
|||
system or visit http://www.kensington.com. |
||||
When you adjust the angle, do not hold the |
Connect the Kensington security system cable |
|||
bottom of the Monitor set frame as shown on |
||||
between the Monitor set and a table. |
||||
the following illustration, as it may injure your |
||||
|
|
|
||
fingers. |
|
|
|
|
|
|
|
|
Do not touch or press the screen when
adjusting the angle of the monitor.
NOTE
The Kensington security system is optional.
You can obtain it from most electronics stores.
NOTE
Tilt from +15 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view.
- 5 15
For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.
10 cm
10 cm
10 cm
10 cm
Front |
Rear |
Using the Kensington security system
The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the
ASSEMBLING AND PREPARING 9
If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set.
When you install the Monitor set using the wall mounting interface (optional parts), attach it carefully so it will not fall.
1Please use screws and a wall mount interface in accordance with VESA Standards.
2If you use screws longer than standard, the monitor might be damaged internally.
3If you use improper screws, the product might be damaged and drop from mounted position. In this case, LG Electronics is not responsible for it.
4VESA compatible only with respect to screw mounting interface dimensions and mounting screw specifications.
5Please use a VESA standard as below.
yy784.8 mm (30.9 inch) and under
*Wall Mount Pad Thickness : 2.6 mm
*Screw : Φ 4.0 mm x Pitch 0.7 mm x Length 10 mm
yy787.4 mm (31.0 inch) and above
*Please use VESA standard wall mount pad and screws.
Model |
E1951S |
E2351T |
|
E2051S |
E2251VR |
|
E2251S |
E2351VR |
|
E1951T |
E2251VQ |
|
E2051T |
E2351VQ |
|
E2251T |
|
VESA (A x B) |
75 x 75 |
|
Standard screw |
M4 |
|
Number of screws |
4 |
|
Wall mount bracket |
RW120 |
|
(optional) |
|
|
yyVESA (A x B)
B A
CAUTION
yyDisconnect the power cord first before moving or installing the Monitor set. Otherwise electric shock may occur.
yyIf you install the Monitor set on a ceiling or slanted wall, it may fall and result in severe injury.
yyUse only an authorized LG wall mount and contact a local dealer or qualified personnel.
yyDo not over tighten the screws as this may cause damage to the Monitor set and void your warranty.
yyUse only screws and wall mounts that meet the VESA standard. Any damages or injuries by misuse or using an improper
accessory are not covered by the warranty.
NOTE
yyUse the screws that are listed on the VESA standard screw specifications.
yyThe wall mount kit will include an installation manual and necessary parts.
yyThe wall mount bracket is optional. You can obtain additional accessories from your local dealer.
yyThe length of screws may differ depending on the wall mount. Be sure to use the proper length.
yyFor more information, refer to the instructions supplied with the wall mount.
ENGLISH
ENGLISH
10 USING THE MONITOR SET
|
E2251VR |
|
E2351VR |
|
E2251VQ |
|
E2351VQ |
yyYour Monitor set supports Plug & Play*. |
|
|
|
|
|
|
|
*Plug & Play: A PC recognizes a connected |
|
|
|
|
|
|
|
device that users connect to a PC and turn |
|
|
|
|
|
|
|
on, without device configuration or user |
|
|
|
|
|
DC-IN / |
|
intervention. |
|
|
|
|
|
|
Transmits analog video from your PC to the Monitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable as shown in the following illustrations.
E1951S E2051SE2251S
DC-IN /
RGB OUT
RGB OUT |
NOTE |
yyWhen using a D-Sub signal input cable connector for Macintosh
DC-IN /
E1951T E2051TE2251TE2351T
yyMac adapter
For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGA connector on the supplied cable to a 15 pin 2 row connector.