LG E2351TC, E2251C, E2051C, E1951C User Manual

ENGLISH

OWNER’S MANUAL

LED LCD MONITOR

Please read this manual carefully before operating your set and retain it for future reference.

LED LCD MONITOR MODELS

E1951S E2051S E2251S

E1951T E2051T E2251T E2351T E2351TC

E1951C E2051C E2251C

E2251VR E2351VR

E2251VQ E2351VQ

www.lg.com

TABLE OF CONTENTS

ENGLISH

ENG

3 ASSEMBLING AND

PREPARING

3 Unpacking

4 Parts and buttons

6 Setting up the Monitor

6 - Assembling the Stand Body and Base

7 - Mounting on a table

8 - Detaching the Stand Base and the

Stand Body

- Mounting on a wall

11 USING THE MONITOR

11 Connecting to a PC

11 - D-SUB connection

12 - DVI-D connection

13 - HDMI connection

21 SPECIFICATIONS

26 Preset Modes (Resolution)

27 - HDMI Video Timing

27 Indicator

28 PROPER POSTURE

28 Proper posture for using the Monitor.

29 LICENSES

14 CUSTOMIZING SETTINGS

14 Accessing The Main Menus

15 Customizing Settings

15 - MENU Settings

16 - SUPER ENERGY SAVING Settings

17 - SUPER+ RESOLUTION Settings

17 - VOLUME Settings (Only supported in

HDMI)

- DUAL MONITOR Settings

18 - DUAL WEB Settings

19 TROUBLESHOOTING

ASSEMBLING AND PREPARING

Unpacking

Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.

CD(Owner's Manual) /

Card

D-SUB Cable

(This signal cable may be attached

to this product before shipping out.)

accessory may not be provided.)

DVI-D Cable

(In some countries, this

ENGLISH

ENG

Power Cord AC-DC Adapter

Screws for Assembly

Stand Body

2 EA

Stand Base

CAUTION

Do not use any unapproved accessories to ensure the safety and product life span.

Any damages or injuries by using unapproved accessories are not covered by the warranty.

NOTE

The accessories supplied with your product may vary depending on the model.

Product specifications or contents in this manual may be changed without prior notice due to upgrade

of product functions. User should use shielded signal interface cables (RGB cable/ DVI-D cable) with ferrite cores to

maintain standard compliance for the product.

ENGLISH

ENG

ASSEMBLING AND PREPARING

Parts and buttons

Power Indicator

Lighting On: Turned on

Lighting Off: Turned off

E1951S

E1951C

E1951T

E2251T

E2051S

E2051C

E2251S

E2251C

D-SUB

E2051T

E2351T E2351TC

D-SUBDVI-D

DC-IN /

䏳㵎幑‣

DC-IN /

䏳㵎幑‣

E2251VR

E2351VR

HDMI

(Power Button)

Button ("CUSTOMIZING SETTINGS" on page 14)

E2251VQ

E2351VQ

DC-IN /

D-SUBDVI-D

Connection panel (See p.11)

䏳㵎幑‣

ASSEMBLING AND PREPARING

Button Description

MENU Accesses the main menus.(See p.15)

Left First Button OSD LOCKED/

SUPER+ RESOLUTION Use this button to enter the SUPER+ RESOLUTION menu. For more information.(See p.17)

DUAL Use this button to enter the DUAL menu.

AUTO Press the AUTO button on the MONITOR SETUP OSD menu to automatically adjust the

VOLUME (Only HDMI mode) E2251VR/ E2351VR/ E2251VQ/ E2351VQ

INPUT You can choose the input signal.

EXIT Exit the OSD(On Screen Display).

(Power Button)

UNLOCKED

For more information.(See p.18)

screen. (Only supported in Analog Mode)

The best display mode

E1951S/ E1951T/ E1951C

E2051S/ E2051T/ E2051C

E2251S/ E2251T/ E2251C/ E2251VR/ E2251VQ/ E2351TC E2351T/ E2351VR E2351VQ

Adjust the volume of the Monitor.(See p.17)

When two input signals are at least are connected, you can select the input signal

(D-SUB/ DVI-D/ HDMI) you want. When only one signal is connected, it is automatically detected. The default setting is

D-SUB.

Turns the power on or off.

Power Indicator The power indicator stays blue if the display is running

This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the Left First Button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the

Left First Button for several seconds. The message "OSD UNLOCKED" should appear.

1366 x 768

1600 x 900

1920 x 1080

properly (On Mode). If the display is in Sleep Mode, the power indicator blinks blue.

ENGLISH

ENG

ASSEMBLING AND PREPARING

ENGLISH

ENG

Setting up the Monitor

Assembling the Stand Body and Base

Place the Monitor with the screen side down on

a flat and cushioned surface.

Attach the Stand Body from the Monitor.

Insert the two Lockers of the Stand Body right into the groove of the Monitor head and secure

them by pressing the left and right bottom sides.

WARNING

If you do not fasten the screws, the monitor

may fall, which may result in damage to the product.

Check the direction of the Stand Base and

assemble it with the Stand Body. Using a

coin, turn the screw clockwise to secure the Stand Base.

Stand Body

Locker

Secure the Stand Body the monitor using 2

screws.

Stand Base

Coin

CAUTION

This illustration depicts the general type of

connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down

holding only the stand base. The product may fall and get damaged or injure your foot. Applying excessive force when fastening

screws may cause damage to the monitor. Damage caused in this way will not be covered by the product warranty.

ASSEMBLING AND PREPARING

DC-IN /

䏳㵎幑‣

Mounting on a table

Lift and tilt the Monitor into its upright position

on a table.

Leave a 10 cm (minimum) space from the wall for proper ventilation.

10 cm

WARNING

When you adjust the angle, do not hold the bottom of the Monitor frame as shown on the following illustration, as it may injure your fingers.

Do not touch or press the screen when adjusting the angle of the monitor.

ENGLISH

ENG

Connect the AC-DC Adapter and Power Cord

to a wall outlet.

DC-IN /

䏳㵎幑‣

CAUTION

Disconnect the power cord first, and then move or install the Monitor. Otherwise electric shock may occur.

NOTE

Tilt from +15 to -5 degrees up or down to adjust the angle of the Monitor to suit your view.

15- 5

Front Rear

ASSEMBLING AND PREPARING

ENGLISH

ENG

Using the Kensington security system

The Kensington security system connector is located at the back of the Monitor. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit

Connect the Kensington security system cable between the Monitor and a table.

http://www.kensington.com

Detaching the Stand Base and the Stand Body

Place the Monitor with the screen side down on

a flat and cushioned surface.

Using a coin, turn the screw in the Stand Base

counterclockwise. Detach the Stand Base from the Stand Body.

NOTE

The Kensington security system is optional. You can obtain it from most electronics stores.

Remove the 2 screws and detach the Stand

Body from the monitor.

Mounting on a wall

For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.

ASSEMBLING AND PREPARING

Please use a VESA standard as below.

784.8 mm (30.9 inch) and under

* Wall Mount Pad Thickness : 2.6 mm * Screw : Φ 4.0 mm x Pitch 0.7 mm x

Length 10 mm

787.4 mm (31.0 inch) and above

* Please use VESA standard wall mount pad

and screws.

ENGLISH

ENG

10 cm

If intend to mount the Monitor to a wall, an optional third-party wall mount must be purchased. When you install the Monitor using the wall mounting interface (optional parts), attach it carefully so it will not fall.

10 cm

Model

E1951S E2051S E2251S

E1951T E2051T E2251T E2351T

E2351TC

VESA (A x B) 75 x 75 Screw Size M4 Number of screws 4 Wall mount bracket

(optional)

VESA (A x B)

RW120

E1951C E2051C E2251C

E2251VR E2351VR

E2251VQ E2351VQ

Please use screws and a wall mount interface

in accordance with VESA Standards.

If you use screws longer than standard, the

monitor might be damaged internally.

If you use improper screws, the product might

be damaged and drop from mounted position. In this case, LG Electronics is not responsible for it.

VESA compatible only with respect to screw

mounting interface dimensions and mounting screw specifications.

+ 21 hidden pages