LG Electronics E2042S, E1942S, E2042T, E2242T, E2442T User Manual

ENGLISH

OWNER’S MANUAL

LED LCD MONITOR

Please read this manual carefully before operating your set and retain it for future reference.

LED LCD MONITOR MODEL

E1942S E2042T E2042S E2242T E2242S E2342T E2442T

www.lg.com

ENGLISH

ENG

TABLE OF CONTENTS

2

ASSEMBLING AND PREPARING

3

ASSEMBLING AND PREPARING

Unpacking

Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.

DVI-D Cable

CD(Owner's Manual) /

Card

D-SUB Cable

(E2042T/E2242T/E2342T/

E2442T)

(This cable is not included

in all countries.)

or

ENGLISH

ENG

Power Cord AC-DC Adapter AC-DC Adapter

( Depending on the country ) ( Depending on the country )

Stand Body

Stand Base

CAUTION

Do not use any unapproved accessories to ensure the safety and product life span.

y

Any damages or injuries by using unapproved accessories are not covered by the warranty.

y

NOTE

The accessories supplied with your product may vary depending on the model.

y

Product specifications or contents in this manual may be changed without prior notice due to upgrade

y

of product functions.

ENGLISH

ENG

ASSEMBLING AND PREPARING

4

Parts and buttons

Power Indicator

Lighting On: Turned on

y

Lighting Off: Turned off

y

Connection panel (See p.9)

(Power Button)

Button (See p.11)

ASSEMBLING AND PREPARING

5

Setting up the Monitor set

Attaching the Stand Base

Place the Monitor set with the screen side

1

down on a flat and cushioned surface.

CAUTION

Lay a foam mat or soft protective cloth on the surface to protect the screen from damage.

1

Attach the Stand Body to the monitor set.

2

Attach the Stand Base.

2

Tighten the screw to the right with a coin.

3

Detaching the Stand Base

Place the Monitor set with the screen side

1

down on a flat and cushioned surface.

1

Pull out the Stand Body and Stand Base

2

from the monitor set.

2

Turn the screw to the left with a coin. Pull out the Stand Base.

3

Stand Body

ENGLISH

ENG

Stand Body

Stand Base

Stand Body

Stand Base

CAUTION

This illustration depicts the general model of

y

connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down holding

y

only the stand base. The product may fall and get damaged or injure your foot.

ASSEMBLING AND PREPARING

6

ENGLISH

ENG

Mounting on a table

Lift and tilt the Monitor set into its upright

1

position on a table.

Leave a 10 cm (minimum) space from the wall for proper ventilation.

10 cm

Press (Power) button on the bottom switch

3

panel to turn the power on.

CAUTION

Unplug the power cord before moving the Monitor to another location. Otherwise electric shock may occur.

Using the cable holder

Connect the AC-DC Adapter and Power Cord

2

to a wall outlet.

or

Cable holder

ASSEMBLING AND PREPARING

7

WARNING

When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as may injure your fingers.

Do not touch or press the screen when adjusting the angle of the monitor.

Do not hold this set like below picture.Monitor screen can detach from stand base and injure your body.

Using the Kensington security system

The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the manual supplied with the Kensington security system or visit

Connect the Kensington security system cable between the Monitor set and a table.

http://www.kensington.com

.

NOTE

ENGLISH

ENG

NOTE

Tilt from +20 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view.

Front Rear

The Kensington security system is optional. You can obtain it from most electronics stores.

ASSEMBLING AND PREPARING

8

ENGLISH

ENG

Mounting on a wall

For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.

10 cm

If you intend to mount the Monitor set to a wall, attach Wall mounting interface (optional parts) to the back of the set. When you install the Monitor set using a wall mounting interface (optional parts), attach it carefully so it will not drop.

Please, Use the screw and wall mount interface

1

in accordance with VESA Standards.

If you use screw longer than standard, the

2

monitor might be damaged internally.

If you use improper screw, the product might be

3

damaged and drop from mounted position. In this case, LG Electronics is not responsible for it.

VESA compatible.

4

Please use VESA standard as below.

5

784.8 mm (30.9 inch) and under

y

* Wall Mount Pad Thickness : 2.6 mm

* Screw : Φ 4.0 mm x Pitch 0.7 mm x

Length 10 mm

787.4 mm (31.0 inch) and above

y

* Please use VESA standard wall mount pad

and screws.

10 cm

Model

E1942S E2042S E2242S

VESA (A x B) 75 x 75 100 x 100 Standard

screw Number of

screws

M4

4

E2042T E2242T E2342T

E2442T

CAUTION

Disconnect the power cord first, and then

y

move or install the Monitor set. Otherwise electric shock may occur. If you install the Monitor set on a ceiling or

y

slanted wall, it may fall and result in severe injury. Use only an authorized LG wall mount

y

and contact the local dealer or qualified personnel. Do not over tighten the screws as this may

y

cause damage to the Monitor set and void your warranty. Use only screws and wall mounts that

y

meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.

NOTE

Use the screws that are listed on the VESA

y

standard screw specifications. The wall mount kit will include an installation

y

manual and necessary parts. The wall mount bracket is optional. You can

y

obtain additional accessories from your local dealer. The length of screws may differ depending

y

on the wall mount. Be sure to use the proper length. For more information, refer to the

y

instructions supplied with the wall mount.

USING THE MONITOR SET

9

USING THE MONITOR SET

Connecting to a PC

Your Monitor set supports Plug & Play*.

y

*Plug & Play: A PC recognizes a connected device that users connect to a PC and turn on, without device configuration or user intervention.

D-SUB connection

Transmits analog video from your PC to the Monitor set. Connect the PC and the Monitor set with the supplied D-sub 15 pin signal cable as shown in the following illustrations.

DVI-D connection

NOTE

When using a D-Sub signal input cable

y

connector for Macintosh

Mac adapter

y

For Apple Macintosh use, a separate plug adapter is needed to change the 15 pin high density (3 row) D-SUB VGA connector on the supplied cable to a 15 pin 2 row connector.

ENGLISH

ENG

Transmits a digital video signal from your PC to the Monitor set. Connect the PC and the Monitor set with a DVI cable as shown in the following illustrations.

USING THE MONITOR SET

10

ENGLISH

ENG

CAUTION

Connect the signal

y

input cable and tighten it by turning the screws clockwise. Do not press the screen with your finger for

y

a long time as this may result in temporary distortion on the screen. Avoid displaying a fixed image on the

y

screen for a long period of time to prevent image burn. Use a screensaver if possible.

Self Image Setting Function

Press the power button on the bottom panel to turn the power on. When monitor power is turned on, the "Self Image Setting" Function is executed automatically. (Only supported in Analog Mode)

NOTE NOTE

When you want to use two PC in our Monitor,

y

please connect the signal cable(D-SUB/ DVI-D) respectively in Monitor set. If you turn the Monitor set on while it is cold,

y

the screen may flicker. This is normal. Some red, green, or blue spots may appear

y

on the screen. This is normal.

"Self Image Setting" Function.

y

This function provides the user with optimal display settings.When the user connects the monitor for the first time, this function automatically adjusts the display to optimal settings for individual input signals.(Only supported in Analog Mode)

‘AUTO’ Function.

y

When you encounter problems such as blurry screen, blurred letters, screen flicker or tilted screen while using the device or after changing screen resolution, press the AUTO function button to improve resolution. (Only supported in Analog Mode)

CUSTOMIZING SETTINGS

11

CUSTOMIZING SETTINGS

Press the desired button on the bottom of the Monitor set.

1

Change the value of the menu item by pressing the buttons on the bottom of the Monitor set.

2

To return to the upper menu or set other menu items, use the up arrow ( ) button.

Select EXIT to leave the OSD menu.

3

Monitor set Buttons

ENGLISH

ENG

Button Description

(SUPER ENERGY SAVING)

(Power Button)

Accesses the main menus.(See p.12)

OSD LOCKED/ UNLOCKED

Use this button to enter SUPER ENERGY SAVING menu.For more information.(See p.17)

Use this button to enter CUSTOM, TEXT, PHOTO, CINEMA, GAME menus.(See p.18)

When adjusting your display settings, always press the AUTO button on the MONITOR SETUP OSD. (Only supported in Analog Mode)

The best display mode E1942S : 1366 x 768

You can choose the input signal.

• When two input signals are connected, you can select the input signal (D-SUB/DVI)

you want.

• When only one signal is connected, it is automatically detected. The default setting is

D-SUB.

EXIT

Exit the OSD(On Screen Display).

Turns the power on or off.

Power Indicator The power indicator stays red if the display is running properly

This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the MENU button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the MENU button for several seconds. The message "OSD UNLOCKED" should appear.

E2042S / E2042T : 1600 x 900 E2242S / E2242T / E2342T / E2442T : 1920 x 1080

(On Mode). If the display is in Sleep Mode, the power indicator blinks red.

ENGLISH

ENG

CUSTOMIZING SETTINGS

12

Customizing Settings

Menu Settings

Press MENU button on the bottom of the Monitor set

1

to display the MENU OSD.

Set the options by pressing the ◄ or ► or ▼

2

buttons.

Select the "NEXT MENU" button to enter the more

3

option settings.

Select EXIT to leave the OSD menu.

4

To return to the upper menu or set other menu items, use the up arrow ( ) button.

Each option is explained below.

MENU Analog Digital Description

BRIGHTNESS

CONTRAST ● ●

WIDE/ORIGINAL

RESET

MENU > NEXT MENU Analog Digital Description

PICTURE

COLOR GAMMA

DISPLAY HORIZONTAL

OTHERS LANGUAGE

● ●

SHARPNESS ● ● To adjust the clearness of the screen .

COLOR TEMP

VERTICAL

CLOCK

PHASE

POWER INDICATOR

WHITE BALANCE ●

To adjust the brightness, contrast of the screen

WIDE

Switch to full screen mode according to input image signal.

ORIGINAL

Change the input image signal ratio to original. * This function works only if input resolution is lower than Monitor set ratio (16:9).

Restore all factory default settings. Press the◄ , ► buttons to reset immediately.

● ● To customize the color of the screen

● To adjust the position of the screen

● To improve the clarity and stability of the screen

● ●

To customize the screen status for a user's operating environment

Analog: D-SUB(Analog signal) input.

y

Digital: DVI-D(Digital signal) input.

y

PICTURE

Press MENU button on the bottom of the Monitor set

1

to display the MENU OSD.

Select the "NEXT MENU" button to enter the more

2

option settings.

Enter to PICTURE by pressing the ▼ button.

3

Set the options by pressing the ◄ or ► or ▼

4

buttons.

Select EXIT to leave the OSD menu.

5

To return to the upper menu or set other menu items, use the up arrow ( ) button.

Each option is explained below.

CUSTOMIZING SETTINGS

13

ENGLISH

ENG

MENU > NEXT MENU > PICTURE Description

SHARPNESS To adjust the clearness of the screen.

ENGLISH

ENG

CUSTOMIZING SETTINGS

14

COLOR

Press MENU button on the bottom of the Monitor set

1

to display the MENU OSD.

Select the "NEXT MENU" button to enter the more

2

option settings.

Select COLOR by pressing the ► button.

3

Enter to COLOR by pressing the ▼ button.

4

Set the options by pressing the ◄ or ► or ▼

5

buttons.

Select EXIT to leave the OSD menu.

6

To return to the upper menu or set other menu items, use the up arrow ( ) button.

Each option is explained below.

MENU > NEXT MENU > COLOR Description

GAMMA Set your own gamma value. : GAMMA 0, GAMMA 1, GAMMA 2 on the monitor,

COLOR TEMP CUSTOM

high gamma values display whitish images and low gamma values display blackish images.

• RED:Set your own red color levels.

• GREEN: Set your own green color levels.

• BLUE:Set your own blue color levels.

Select the screen color.

WARM: Set the screen to warm color temperature (more red). MEDIUM: Set the screen to medium color temperature. COOL: Set the screen to cool color temperature (more blue).

CUSTOMIZING SETTINGS

DISPLAY

Press MENU button on the bottom of the Monitor set

1

to display the MENU OSD.

Select the "NEXT MENU" button to enter the more

2

option settings.

Select DISPLAY by pressing the ► button.

3

Enter to DISPLAY by pressing the ▼ button.

4

Set the options by pressing the ◄ or ► or ▼

5

buttons.

Select EXIT to leave the OSD menu.

6

To return to the upper menu or set other menu items, use the up arrow ( ) button.

Each option is explained below.

MENU > NEXT MENU > DISPLAY Description

HORIZONTAL To move image left and right.

VERTICAL To move image up and down.

CLOCK To minimize any vertical bars or stripes visible on the screen background.The

PHASE To adjust the focus of the display. This item allows you to remove any horizontal

horizontal screen size will also change.

noise and clear or sharpen the image of characters.

15

ENGLISH

ENG

CUSTOMIZING SETTINGS

16

ENGLISH

ENG

OTHERS

Press MENU button on the bottom of the Monitor set

1

to display the MENU OSD.

Select the "NEXT MENU" button to enter the more

2

option settings.

Select OTHERS by pressing the ► button.

3

Enter to OTHERS by pressing the ▼ button.

4

Set the options by pressing the ◄ or ► or ▼

5

buttons.

Select EXIT to leave the OSD menu.

6

To return to the upper menu or set other menu items, use the up arrow ( ) button.

Each option is explained below.

MENU > NEXT MENU > OTHERS Description

LANGUAGE To choose the language in which the control names are displayed.

POWER INDICATOR

WHITE BALANCE

Use this function to set the power indicator on the bottom side of the monitor to ON or OFF.If you set OFF, it will go off. If you set ON at any time, the power indicator will automatically be turned on.

If the output of the video card is different the required specifications,the color level may deteriorate due to video signal distortion. Using this function, the signal level is adjusted to fit into the standard output level of the video card in order to provide the optimal image.Activate this function when white and black colors are present in the screen.

CUSTOMIZING SETTINGS

17

SUPER ENERGY SAVING Setting

Press ( SUPER ENERGY SAVING ) button on

1

the bottom of the Monitor set to display the SUPER ENERGY SAVING OSD.

Set the options by pressing the ◄ or ► or ▼ buttons.

2

Select EXIT to leave the OSD menu.

3

Each option is explained below.

SUPER ENERGY SAVING Description

ON

OFF Disables SUPER ENERGY SAVING.

RESET Resets the values of total energy consumption reduction and CO2 emission reduction

NOTE

TOTAL POWER REDUCTION: How much power is saved while using the monitor.

y

TOTAL CO2 REDUCTION: Change the TOTAL POWER REDUCTION to CO2.

y

SAVING DATA(W/h)

y

SUPER SAVING 4 W/h 5 W/h 6 W/h 7 W/h 7 W/h

Enables SUPER ENERGY SAVING you can save energy with this energy- efficient function

estimates.

470 mm

(18.5 inch)

508 mm

(20 inch)

546 mm

(21.5 inch)

584 mm

(23 inch)

609 mm

(24 inch)

ENGLISH

ENG

Saving Data depends on the Panel. So,those values should be different from each panel and panel

y

vendor. LG calculated these values by using “broadcast video signal”

y

(including broadcast video: IEC 62087)

SUPER SAVING refers to how much power can be saved using the SUPER ENERGY SAVING

y

function.

CUSTOMIZING SETTINGS

18

ENGLISH

ENG

PICTURE MODE Setting

Press MODE button on the bottom of the Monitor set to display the PICTURE MODE OSD .

1

Set the options by pressing the ◄ or ► or ▼ buttons.

2

Select EXIT to leave the OSD menu.

3

Each option is explained below.

PICTURE MODE Description

CUSTOM It is a mode that the user can adjust each element. It can adjust the color mode of the Main Menu.

TEXT It is a mode that the screen is adjusted to the best for the text works.

PHOTO It is a mode that the screen is adjusted to the best to view pictures.

CINEMA It is a mode that the screen is adjusted to the best to view the videos.

GAME It is a mode that the screen is adjusted to the best to play a game.

TROUBLESHOOTING

19

TROUBLESHOOTING

Check the following before calling for service.

No image appears

Is the power cord of the display connected?

Is the power indicator light on?

Is the power on and the power indicator Red?

Is the power indicator flickering?

Do you see an "OUT OF RANGE" message on the screen?

Do you see a "NO SIGNAL" message on the screen?

Do you see a "OSD LOCKED" message on the screen?

Do you see “OSD LOCKED” when you push MENU button?

yCheck and see if the power cord is connected properly to the power

outlet.

yPress the Power button.

yAdjust the brightness and the contrast.

yIf the display is in power saving mode, try moving the mouse or

pressing any key on the keyboard to bring up the screen.

yTry to turn on the PC.

yThis message appears when the signal from the PC (video card) is

out of horizontal or vertical frequency range of the display. See the 'Specifications' section of this manual and configure your display again.

yWhen the monitor is on "No-Signal" in 5 minutes, the monitor goes to

DPM mode.

yYou can secure the current control settings, so that they cannot be

inadvertently changed. You can unlock the OSD controls at any time by pushing the MENU button for several seconds: the message “OSD UNLOCKED” will appear.

ENGLISH

ENG

Display image is incorrect

Display Position is incorrect.

On the screen background, vertical bars or stripes are visible.

Any horizontal noise appearing in any image or characters are not clearly portrayed.

yPress the AUTO button to automatically adjust your display image to

the ideal setting.

yPress the AUTO button to automatically adjust your display image to

the ideal setting.

yPress the AUTO button to automatically adjust your display image to

the ideal setting.

yCheck Control Panel ► Display ► Settings and adjust the display

to the recommended resolution or adjust the display image to the ideal setting. Set the color setting higher than 24 bits (true color).

ENGLISH

ENG

TROUBLESHOOTING

20

CAUTION

Check Control Panel ► Display ► Settings and see if the frequency or the resolution were

y

changed. If yes, readjust the video card to the recommend resolution. If the recommended resolution (optimal resolution) is not selected, letters may be blurred and the

y

screen may be dimmed, truncated or biased. Make sure to select the recommend resolution. The setting method can differ by computer and O/S (Operation System), and resolution mentioned

y

above may not be supported by the video card performance. In this case, please ask to the computer or the video card manufacturer.

Display image is incorrect

The screen color is mono or abnormal.

The screen blinks.

yCheck if the signal cable is properly connected and use a screwdriver

to fasten if necessary. yMake sure the video card is properly inserted in the slot. ySet the color setting higher than 24 bits (true color) at Control Panel

► Settings.

yCheck if the screen is set to interlace mode and if yes, change it to the

recommend resolution.

Do you see an "Unrecognized monitor, Plug&Play (VESA DDC) monitor found" message?

Have you installed the display driver?

yBe sure to install the display driver from the display driver CD (or

diskette) that comes with your display. Or, you can also download the

driver from our web site: http://www.lg.com. yMake sure to check if the video card supports Plug&Play function.

SPECIFICATIONS

21

SPECIFICATIONS

E1942S

Display Screen Type 47.0 cm (18.5 inch) Flat Panel Active matrix-TFT LCDAnti-

Glare coating Visible diagonal size: 47.0 cm

Pixel Pitch 0.3 mm x 0.3 mm (Pixel Pitch)

Sync Input Horizontal Frequency 30 kHz to 61 kHz (Automatic)

Vertical Frequency 56Hz to 75Hz (D-SUB)

Input Form Separate Sync.

Video Input Signal Input 15 pin D-SUB Connector

Input Form RGB Analog (0.7 Vp-p/ 75 ohm)

Resolution Max D-SUB(Analog) : 1366 x 768 @ 60 Hz

Recommend VESA 1366 x 768 @ 60 Hz

Plug & Play DDC 2B(Analog)

Power Consumption

Power Input 19 V 1.2 A

AC-DC Adapter

Dimensions (Width x Height x Depth)

Weight 2.1 kg

Tilt Range -5° to 20°

Environmental conditions

Stand Base Attached ( ), Detached (O)

Power cord Wall-outlet type

On Mode : 15 W(Typ.)

Sleep Mode ≤ 0.3 W Off Mode ≤ 0.3 W

Type ADS-40SG-19-3 19025G, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPG-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPBR-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPI-1,manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPCU-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type LCAP21, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE

OUTPUT: 19 V 1.3 A

With Stand 44.1 cm x 34.9 cm x 16.8 cm

Without Stand 44.1 cm x 27.5 cm x 5.5 cm

Operating Temperature Operating Humidity

Storage Temperature Storage Humidity

10°C to 35 °C 10 % to 80 %

-20°C to 60 °C 5 % to 90 % non-Condensing

ENGLISH

ENG

Product specifications shown above may be changed without prior notice due to upgrade of product functions.

SPECIFICATIONS

22

ENGLISH

ENG

SPECIFICATIONS

E2042S

Display Screen Type 50.8 cm (20 inch) Flat Panel Active matrix-TFT LCDAnti-

Glare coating Visible diagonal size: 50.8 cm

Pixel Pitch 0.276 mm x 0.276 mm (Pixel Pitch)

Sync Input Horizontal Frequency 30 kHz to 83 kHz (Automatic)

Vertical Frequency 56Hz to 75Hz (D-SUB)

Input Form Separate Sync.

Video Input Signal Input 15 pin D-SUB Connector

Input Form RGB Analog (0.7 Vp-p/ 75 ohm)

Resolution Max D-SUB(Analog) : 1600 x 900 @ 60 Hz

Recommend VESA 1600 x 900 @ 60 Hz

Plug & Play DDC 2B(Analog)

Power Consumption

Power Input 19 V 1.2 A

AC-DC Adapter

Dimensions (Width x Height x Depth)

Weight 2.3 kg

Tilt Range -5° to 20°

Environmental conditions

Stand Base Attached ( ), Detached (O)

Power cord Wall-outlet type

On Mode : 20 W(Typ.)

Sleep Mode ≤ 0.3 W Off Mode ≤ 0.3 W

Type ADS-40SG-19-3 19025G, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPG-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPBR-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPI-1,manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPCU-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type LCAP21, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE

OUTPUT: 19 V 1.3 A

With Stand 47.4 cm x 36.6 cm x 16.8 cm

Without Stand 47.4 cm x 29.2 cm x 5.5 cm

Operating Temperature Operating Humidity

Storage Temperature Storage Humidity

10°C to 35 °C 10 % to 80 %

-20°C to 60 °C 5 % to 90 % non-Condensing

Product specifications shown above may be changed without prior notice due to upgrade of product functions.

SPECIFICATIONS

23

SPECIFICATIONS

E2042T

Display Screen Type 50.8 cm (20 inch) Flat Panel Active matrix-TFT LCDAnti-

Glare coating Visible diagonal size: 50.8 cm

Pixel Pitch 0.276 mm x 0.276 mm (Pixel Pitch)

Sync Input Horizontal Frequency 30 kHz to 83 kHz (Automatic)

Vertical Frequency 56Hz to 75Hz (D-SUB, DVI-D)

Input Form Separate Sync. Digital

Video Input Signal Input 15 pin D-SUB Connector /DVI-D Connector (Digital)

Input Form RGB Analog (0.7 Vp-p/ 75 ohm),Digital

Resolution Max D-SUB(Analog) : 1600 x 900 @ 60 Hz

Recommend VESA 1600 x 900 @ 60 Hz

Plug & Play DDC 2B(Analog,Digital)

Power Consumption

Power Input 19 V 1.2 A

AC-DC Adapter

Dimensions (Width x Height x Depth)

Weight 2.3 kg

Tilt Range -5° to 20°

Environmental conditions

Stand Base Attached ( ), Detached (O)

Power cord Wall-outlet type

On Mode : 20 W(Typ.)

Sleep Mode ≤ 0.3 W Off Mode ≤ 0.3 W

Type ADS-40SG-19-3 19025G, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPG-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPBR-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPI-1,manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPCU-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type LCAP21, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE

OUTPUT: 19 V 1.3 A

With Stand 47.4 cm x 36.6 cm x 16.8 cm

Without Stand 47.4 cm x 29.2 cm x 5.5 cm

Operating Temperature Operating Humidity

Storage Temperature Storage Humidity

DVI (Digital) : 1600 x 900 @ 60 Hz

10°C to 35 °C 10 % to 80 %

-20°C to 60 °C 5 % to 90 % non-Condensing

ENGLISH

ENG

Product specifications shown above may be changed without prior notice due to upgrade of product functions.

SPECIFICATIONS

24

ENGLISH

ENG

SPECIFICATIONS

E2242S

Display Screen Type 54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCDAnti-

Glare coating Visible diagonal size: 54.6 cm

Pixel Pitch 0.247 mm x 0.247 mm (Pixel Pitch)

Sync Input Horizontal Frequency 30 kHz to 83 kHz (Automatic)

Vertical Frequency 56Hz to 75Hz (D-SUB)

Input Form Separate Sync.

Video Input Signal Input 15 pin D-SUB Connector

Input Form RGB Analog (0.7 Vp-p/ 75 ohm)

Resolution Max D-SUB(Analog) : 1920 x 1080 @ 60 Hz

Recommend VESA 1920 x 1080 @ 60 Hz

Plug & Play DDC 2B(Analog)

Power Consumption

Power Input 19 V 1.2 A

AC-DC Adapter

Dimensions (Width x Height x Depth)

Weight 2.6 kg

Tilt Range -5° to 20°

Environmental conditions

Stand Base Attached ( ), Detached (O)

Power cord Wall-outlet type

On Mode : 23 W(Typ.)

Sleep Mode ≤ 0.3 W Off Mode ≤ 0.3 W

Type ADS-40SG-19-3 19025G, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPG-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPBR-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPI-1,manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPCU-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type LCAP21, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE

OUTPUT: 19 V 1.3 A

With Stand 50.9 cm x 38.7 cm x 18.1 cm

Without Stand 50.9 cm x 31.3 cm x 5.5 cm

Operating Temperature Operating Humidity

Storage Temperature Storage Humidity

10°C to 35 °C 10 % to 80 %

-20°C to 60 °C 5 % to 90 % non-Condensing

Product specifications shown above may be changed without prior notice due to upgrade of product functions.

SPECIFICATIONS

25

SPECIFICATIONS

E2242T

Display Screen Type 54.6 cm (21.5 inch) Flat Panel Active matrix-TFT LCDAnti-

Glare coating Visible diagonal size: 54.6 cm

Pixel Pitch 0.247 mm x 0.247 mm (Pixel Pitch)

Sync Input Horizontal Frequency 30 kHz to 83 kHz (Automatic)

Vertical Frequency 56Hz to 75Hz (D-SUB, DVI-D)

Input Form Separate Sync. Digital

Video Input Signal Input 15 pin D-SUB Connector /DVI-D Connector (Digital)

Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital

Resolution Max D-SUB(Analog) : 1920 x 1080 @ 60 Hz

Recommend VESA 1920 x 1080 @ 60 Hz

Plug & Play DDC 2B(Analog,Digital)

Power Consumption

Power Input 19 V 1.2 A

AC-DC Adapter

Dimensions (Width x Height x Depth)

Weight 2.6 kg

Tilt Range -5° to 20°

Environmental conditions

Stand Base Attached ( ), Detached (O)

Power cord Wall-outlet type

On Mode : 23 W(Typ.)

Sleep Mode ≤ 0.3 W Off Mode ≤ 0.3 W

Type ADS-40SG-19-3 19025G, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPG-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPBR-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPI-1,manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPCU-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type LCAP21, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE

OUTPUT: 19 V 1.3 A

With Stand 50.9 cm x 38.7 cm x 18.1 cm

Without Stand 50.9 cm x 31.3 cm x 5.5 cm

Operating Temperature Operating Humidity

Storage Temperature Storage Humidity

DVI (Digital) : 1920 x 1080 @ 60 Hz

10°C to 35 °C 10 % to 80 %

-20°C to 60 °C 5 % to 90 % non-Condensing

ENGLISH

ENG

Product specifications shown above may be changed without prior notice due to upgrade of product functions.

SPECIFICATIONS

26

SPECIFICATIONS

ENGLISH

ENG

E2342T

Display Screen Type 58.4 cm (23 inch) Flat Panel Active matrix-TFT LCDAnti-

Pixel Pitch 0.265 mm x 0.265 mm (Pixel Pitch)

Sync Input Horizontal Frequency 30 kHz to 83 kHz (Automatic)

Vertical Frequency 56Hz to 75Hz (D-SUB, DVI-D)

Input Form Separate Sync. Digital

Video Input Signal Input 15 pin D-SUB Connector /DVI-D Connector (Digital)

Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital

Resolution Max D-SUB(Analog) : 1920 x 1080 @ 60 Hz

Recommend VESA 1920 x 1080 @ 60 Hz

Plug & Play DDC 2B(Analog,Digital)

Power Consumption

On Mode : 24 W(Typ.)

Sleep Mode ≤ 0.3 W Off Mode ≤ 0.3 W

Power Input 19 V 1.3 A

AC-DC Adapter

Type ADS-40SG-19-3 19032G, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPG-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPBR-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPI-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPCU-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type LCAP21A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE

OUTPUT: 19 V 1.7 A

Type ADS-40SG-19-3 19025G, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPG-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPBR-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPI-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19025GPCU-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type LCAP21, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE

OUTPUT: 19 V 1.3 A

Dimensions (Width x Height x Depth)

With Stand 54.4 cm x 40.6 cm x 18.1 cm

Without Stand 54.4 cm x 33.2 cm x 5.5 cm

Weight 2.9 kg

Tilt Range -5° to 20°

Environmental conditions

Operating Temperature Operating Humidity

Storage Temperature Storage Humidity

Stand Base Attached ( ), Detached (O)

Power cord Wall-outlet type

Glare coating Visible diagonal size: 58.4 cm

DVI (Digital) : 1920 x 1080 @ 60 Hz

10°C to 35 °C 10 % to 80 %

-20°C to 60 °C 5 % to 90 % non-Condensing

Product specifications shown above may be changed without prior notice due to upgrade of product functions.

SPECIFICATIONS

27

SPECIFICATIONS

E2442T

Display Screen Type 60.9 cm (24 inch) Flat Panel Active matrix-TFT LCDAnti-

Glare coating Visible diagonal size: 60.9 cm

Pixel Pitch 0.277 mm x 0.277 mm (Pixel Pitch)

Sync Input Horizontal Frequency 30 kHz to 83 kHz (Automatic)

Vertical Frequency 56Hz to 75Hz (D-SUB, DVI-D)

Input Form Separate Sync. Digital

Video Input Signal Input 15 pin D-SUB Connector /DVI-D Connector (Digital)

Input Form RGB Analog (0.7 Vp-p/ 75 ohm), Digital

Resolution Max D-SUB(Analog) : 1920 x 1080 @ 60 Hz

Recommend VESA 1920 x 1080 @ 60 Hz

Plug & Play DDC 2B(Analog,Digital)

Power Consumption

Power Input 19 V 1.6 A

AC-DC Adapter

Dimensions (Width x Height x Depth)

Weight 3.6 kg

Tilt Range -5° to 20°

Environmental conditions

Stand Base Attached ( ), Detached (O)

Power cord Wall-outlet type

On Mode : 25 W(Typ.)

Sleep Mode ≤ 0.3 W Off Mode ≤ 0.3 W

Type ADS-40SG-19-3 19032G, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPG-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPBR-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPI-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type ADS-40FSG-19 19032GPCU-1, manufactured by SHENZHEN HONOR ELECTRONIC or Type LCAP21A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-A, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-E, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-I, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE or Type LCAP26A-B, manufactured by LIEN CHANG ELECTRONIC ENTERPRISE

OUTPUT: 19 V 1.7 A

With Stand 56.7 cm x 41.8 cm x 18.1 cm

Without Stand 56.7 cm x 34.3 cm x 5.5 cm

Operating Temperature Operating Humidity

Storage Temperature Storage Humidity

DVI (Digital) : 1920 x 1080 @ 60 Hz

10°C to 35 °C 10 % to 80 %

-20°C to 60 °C 5 % to 90 % non-Condensing

ENGLISH

ENG

Product specifications shown above may be changed without prior notice due to upgrade of product functions.

ENGLISH

ENG

SPECIFICATIONS

28

Preset Modes (Resolution)

E1942S

Display Modes (Resolution)

720 x 400 31.468 70 -/+

640 x 480 31.469 60 -/-

640 x 480 37.500 75 -/-

800 x 600 37.879 60 +/+

800 x 600 46.875 75 +/+

832 x 624 49.725 75 -/-

1024 x 768 48.363 60 -/-

1024 x 768 60.123 75 +/+

1366 x 768 47.712 60 +/+ Recommend Mode

Horizontal Frequency(kHz)

Vertical Frequency(Hz)

Polarity(H/V)

E2042S/E2042T

Display Modes (Resolution)

720 x 400 31.468 70 -/+

640 x 480 31.469 60 -/-

640 x 480 37.500 75 -/-

800 x 600 37.879 60 +/+

800 x 600 46.875 75 +/+

1024 x 768 48.363 60 -/-

1024 x 768 60.123 75 +/+

1152 x 864 67.500 75 +/+

Horizontal Frequency(kHz)

60.000 60 +/+ Recommend Mode1600 x 900

Vertical Frequency(Hz)

Polarity(H/V)

SPECIFICATIONS

Preset Modes (Resolution)

E2242S/E2242T/E2342T/E2442T

Display Modes (Resolution)

720 x 400 31.468 70 -/+

640 x 480 31.469 60 -/-

640 x 480 37.500 75 -/-

800 x 600 37.879 60 +/+

800 x 600 46.875 75 +/+

1024 x 768 48.363 60 -/-

1024 x 768 60.023 75 +/+

1152 x 864 67.500 75 +/+

1280 x 1024 63.981 60 +/+

1280 x 1024 79.976 75 +/+

1680 x 1050 65.290 60 -/+

1920 x 1080 67.500 60 +/+ Recommend Mode

Horizontal Frequency(kHz)

Vertical Frequency(Hz)

Polarity(H/V)

29

ENGLISH

ENG

Indicator

Mode LED Color

On Mode Red

Sleep Mode Blinking Red

Off Mode Off

PROPER POSTURE

30

ENGLISH

ENG

horizontally outright.

PROPER POSTURE

Proper posture for using the Monitor set.

Adjust the

Monitor set and

your posture to

allow you to view

images at the

optimal viewing

angle.

Place your hands

gently on the

keyboard, keeping

your arms bent at

the elbows and

Adjust the location of the Monitor set to avoid it reflecting light.

Make sure to read the Safety Precautions before using the product. Keep the Owner’s Manual (CD) in an accessible place for future reference. The model and serial number of the SET is located on the back and one side of the SET. Record it below should you ever need service.

MODEL

SERIAL

ENERGY STAR is a set of power-saving guidelines issued by the U.S.Environmental Protection Agency(EPA).

As an ENERGY STAR Partner LGE U. S. A.,Inc. has determined that this product meets the ENERGY STAR guidelines for energy efﬁciency.

LG Electronics E2042S, E1942S, E2042T, E2242T, E2442T User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual

OWNER’S MANUAL

CONTENTS

ASSEMBLING AND PREPARING

Unpacking

Parts and buttons

Setting up the Monitor set

Attaching the Stand Base

Detaching the Stand Base

Mounting on a table

Using the cable holder

Mounting on a wall

USING THE MONITOR SET

Connecting to a PC

D-SUB connection

DVI-D connection

CUSTOMIZING SETTINGS

CUSTOMIZING SETTINGS

Menu Settings

PICTURE

COLOR

DISPLAY

OTHERS

SUPER ENERGY SAVING Setting

PICTURE MODE Setting

TROUBLESHOOTING

SPECIFICATIONS

E1942S

E2042S

E2042T

E2242S

E2242T

E2342T

E2442T

Preset Modes (Resolution)

Indicator

PROPER POSTURE

Proper posture for using the Monitor set.