LG E2351T, E2051T, E1951S, E1951T, E2351VR User Manual

...

ENGLISH

OWNER’S MANUAL

LED LCD MONITOR

Please read this manual carefully before operating your set and retain it for future reference.

LED LCD MONITOR MODELS

E1951S E2051S E2251S

E1951T E2051T E2251T E2351T

E2251VR E2351VR

E2251VQ E2351VQ

www.lg.com

TABLE OF CONTENTS

ENGLISH

ENG

3 ASSEMBLING AND PREPAR-

ING

3 Unpacking

4 Parts and buttons

6 Setting Up the Monitor set

6 - Attaching the Stand Base

6 - Detaching the stand base

7 - Detaching the Stand Body

Wall mount)

7 - Mounting on a table

8 - Mounting on a wall

10 USING THE MONITOR SET

10 Connecting to a PC

10 - D-SUB connection

11 - DVI to HDMI connection

12 - HDMI connection

(Using the

28 PROPER POSTURE

28 Proper posture for using the Monitor set.

29 LICENSES

13 CUSTOMIZING SETTINGS

13 Accessing The Main Menus

14 Customizing Settings

14 - Menu Settings

15 - SUPER ENERGY SAVING Settings

16 - SUPER+ RESOLUTION Settings

16 - Volume Settings (Only supported in

HDMI)

17 - DUAL MONITOR Settings

17 - DUAL WEB Settings

18 TROUBLESHOOTING

20 SPECIFICATIONS

26 Preset Modes (Resolution)

26 - D-SUB / DVI Timing

27 - HDMI Timing

27 Indicator

ASSEMBLING AND PREPARING

Unpacking

Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and accessories.

CD(Owner's Manual) /

Card

D-SUB Cable

(This signal cable may be attached

to this product before shipping out.)

(E1951T/E2051T/E2251T/E2351T/

E2251VR/E2351VR/E2251VQ/

(This cable is not included in all

DVI-D Cable

E2351VQ)

countries.)

ENGLISH

ENG

Power Cord AC-DC Adapter

Stand Body Two Screws

Stand Base

CAUTION

Do not use any unapproved accessories to ensure the safety and product life span.

Any damages or injuries by using unapproved accessories are not covered by the warranty.

NOTE

The accessories supplied with your product may vary depending on the model.

Product specifications or contents in this manual may be changed without prior notice due to upgrade

of product functions. User should use shielded signal interface cables (RGB cable) with ferrite cores (core in the

connector) to maintain standard compliance for the product.

ENGLISH

ENG

ASSEMBLING AND PREPARING

Parts and buttons

Power Indicator

Lighting On: Turned on

Lighting Off: Turned off

E1951S E2051S E2251S

E1951T

E2251T

E2051T

E2351T

E2251VR

E2351VR

(Power Button)

Button ("CUSTOMIZING SETTINGS" on page 13)

E2251VQ

E2351VQ

Connection panel (See p.10)

ASSEMBLING AND PREPARING

Button Description

MENU Accesses the main menus.(See p.14)

Left First Button OSD LOCKED/

SUPER+ RESOLUTION Use this button to enter the SUPER+ RESOLUTION menu. For more information.(See p.16)

DUAL Use this button to enter the DUAL menu.

AUTO To automatically adjust the screen, press the AUTO button on the MONITOR SETUP

VOLUME (Only HDMI mode) E2251VR / E2351VR / E2251VQ / E2351VQ

INPUT You can choose the input signal.

EXIT Exit the OSD(On Screen Display).

(Power Button)

UNLOCKED

For more information.(See p.17)

OSD. (Only supported in Analog Mode)

The best display mode

E1951S / E1951T 1366 x 768

E2051S / E2051T 1600 x 900

E2251S / E2251T E2251VR / E2251VQ E2351T / E2351VR E2351VQ

Adjust the volume of the Monitor set.(See p.16)

yWhen two input signals are at least are connected, you can select the input signal

(D-SUB/HDMI) you want.

yWhen only one signal is connected, it is automatically detected. The default setting is

D-SUB.

Turns the power on or off.

Power Indicator The power indicator stays white if the display is running

This function allows you to lock the current control settings, so that they cannot be inadvertently changed. Press and hold the Left First Button for several seconds. The message "OSD LOCKED" should appear. You can unlock the OSD controls at any time by pushing the

Left First Button for several seconds. The message "OSD UNLOCKED" should appear.

1920 x 1080

properly (On Mode). If the display is in Sleep Mode, the power indicator color is red.

ENGLISH

ENG

ENGLISH

ENG

ASSEMBLING AND PREPARING

Setting Up the Monitor set

Attaching the Stand Base

Place the monitor's screen face down.

CAUTION

To protect the screen from scratches, cover

the surface with a soft cloth.

Put the Stand Body on the set and use the

screws to fix.

Using a coin, turn the screw clockwise to se-

cure the stand base.

Stand Base

Detaching the stand base

Place the monitor's screen face down.

To protect the screen from scratches, cover the surface with a soft cloth.

Stand Body

Check the position (at the front and rear) of

the stand body, then mount the stand base on the stand body as shown in the figure.

Stand Body

Stand Base

CAUTION

Push stand base tightly before turn the

screw in.

Using a coin, turn the screw in the stand base

counterclockwise. Detach the stand base from the stand body.

Stand Body

Stand Base

CAUTION

This illustration depicts the general type of

connection. Your monitor may differ from the items shown in the picture. Do not carry the product upside down

holding only the stand base. The product may fall and get damaged or injure your foot.

Detaching the Stand Body

(Using

the Wall mount)

Remove 2 screws and detach the Stand Body.

ASSEMBLING AND PREPARING

Connect the AC-DC Adapter and Power Cord

to a wall outlet.

ENGLISH

ENG

Mounting on a table

Lift and tilt the Monitor set into its upright

position on a table.

Leave a 10 cm (minimum) space from the wall for proper ventilation.

10 cm

Press Power button on the front switch of panel

to turn the power on.

CAUTION

Disconnect the power cord first, and then move or install the Monitor set. Otherwise electric shock may occur.

ENGLISH

ENG

ASSEMBLING AND PREPARING

WARNING

When you adjust the angle, do not hold the bottom of the Monitor set frame as shown on the following illustration, as it may injure your fingers.

Do not touch or press the screen when adjusting the angle of the monitor.

manual supplied with the Kensington security system or visit

Connect the Kensington security system cable between the Monitor set and a table.

http://www.kensington.com

NOTE

Tilt from +15 to -5 degrees up or down to adjust the angle of the Monitor set to suit your view.

15- 5

Front Rear

The Kensington security system is optional. You can obtain it from most electronics stores.

Mounting on a wall

For proper ventilation, allow a clearance of 10 cm on each side and from the wall. Detailed instructions are available from your dealer, see the optional Tilt Wall Mounting Bracket Installation and Setup Guide.

10 cm

Using the Kensington security system

The Kensington security system connector is located at the back of the Monitor set. For more information of installation and using, refer to the

ASSEMBLING AND PREPARING

If you intend to mount the Monitor set to a wall, an optional third-party wall mount must be purchased. When you install the Monitor set using the wall mounting interface (optional parts), attach it carefully so it will not fall.

Please use screws and a wall mount interface

in accordance with VESA Standards.

If you use screws longer than standard, the

monitor might be damaged internally.

If you use improper screws, the product might be

damaged and drop from mounted position. In this case, LG Electronics is not responsible for it.

VESA compatible only with respect to screw

mounting interface dimensions and mounting screw specifications.

Please use a VESA standard as below.

784.8 mm (30.9 inch) and under

* Wall Mount Pad Thickness : 2.6 mm * Screw : Φ 4.0 mm x Pitch 0.7 mm x

Length 10 mm

787.4 mm (31.0 inch) and above

* Please use VESA standard wall mount pad

and screws.

Model

E1951S E2051S E2251S

E1951T E2051T

E2351T E2251VR E2351VR

E2251VQ E2351VQ

E2251T

VESA (A x B) 75 x 75 Screw Size M4 Number of screws 4 Wall mount bracket

(optional)

RW120

VESA (A x B)

CAUTION

Disconnect the power cord first before

moving or installing the Monitor set. Otherwise electric shock may occur. If you install the Monitor set on a ceiling or

slanted wall, it may fall and result in severe injury. Use only an authorized LG wall mount and

contact a local dealer or qualified personnel. Do not over tighten the screws as this may

cause damage to the Monitor set and void your warranty. Use only screws and wall mounts that

meet the VESA standard. Any damages or injuries by misuse or using an improper accessory are not covered by the warranty.

NOTE

Only use screws that are listed on the VESA

standard screw specifications. The wall mount kit will include an installation

manual and necessary parts. The wall mount bracket is optional. You can

obtain additional accessories from your local dealer. The length of screws may differ depending

on the wall mount. Be sure to use the proper length. For more information, refer to the

instructions supplied with the wall mount.

ENGLISH

ENG

+ 21 hidden pages