lg DU-42PZ60A, DU-42PZ60B, DU-42PZ60C, DU-42PZ60K, DU-42PZ60R OWNER’S MANUAL

...

PLASMATV

OWNER’S MANUAL

MODELS:

DU-42PZ60/60A/60B/60C/60K/60R/60S DU-42PZ60H/60HA/60HB/60HC/60HK/60HR/60HS DU-42PZ70/70A/70B/70C/70K/70R/70S DU-42PZ70H/70HA/70HB/70HC/70HK/70HR/70HS DU-50PZ60/60A/60B/60C/60K/60R/60S DU-50PZ60H/60HA/60HB/60HC/60HK/60HR/60HS DU-50PZ70/70A/70B/70C/70K/70R/70S DU-50PZ70H/70HA/70HB/70HC/70HK/70HR/70HS

Please read this manual carefully and completely before operating your TV. Retain this manual for future reference. Record model number and serial number of the TV in the spaces provided below. See the label attached on the back cover and relate this information to your dealer if you require service.

Model Number : Serial Number :

Internet Home Page : http://www.lge.com

Warning

WARNING

RISK OF ELECTRIC SHOCK DO NOT OPEN

arning

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of impor-

tant operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLYINSERT.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

COMPLIANCE:

The responsible party for this product’s compliance is: LG Electronics.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.

Marketed and Distributed in the United States by LG Electronics U.S.A., Inc. 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632

2 Plasma TV

Safety Instructions

PORTABLE CART WARNING

Safety Instructions

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this manual can help you get many years of enjoyment and safe operation that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for future reference.

4. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Water and Moisture

Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Power-Cord Polarization

This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

Owner’s Manual 3

Safety Instructions

Antenna Lead in Wire

Antenna Discharge Unit (NEC Section 810-20)

Grounding Conductor (NEC Section 810-21)

Ground Clamps Power Service Grounding

Electrode System (NEC Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Safety Instructions continued

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

Example of Grounding According to National Electrical Code Instructions

NEC - National Electrical Code

15. Lightning

For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

16. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

19. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the

product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and

will often require extensive work by a qualified technician

to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been

damaged. f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product.

24. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

18. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

4 Plasma TV

Contents

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .3~4

Introduction

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .7

Connection Options . . . . . . . . . . . . . . . . . . . . . .8

Remote Control Key Functions . . . . . . . . . . . . . .9

Installation

Installation Instruction . . . . . . . . . . . . . . . . . . . . . .10

External Equipment Connections . . . . . . . . . .11~15

Antenna Connection . . . . . . . . . . . . . . . . . . . . .11

VCR Setup / Cable TV Setup . . . . . . . . . . . . . .12

External A/V Source Setup . . . . . . . . . . . . . . . .13

Monitor Out Setup / DVD Setup . . . . . . . . . . . .13

HDSTB Setup / Digital Audio Output . . . . . . . . .14

PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

Operation

Screen Setup for PC mode

Adjustments for screen position, clock, and phase

Turning the TV On . . . . . . . . . . . . . . . . . . . . . . . .17

On-screen Menus Language Selection . . . . . . . . .17

Setup Menu Options

EZ Scan (Channel Search) . . . . . . . . . . . . . . . .18

Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . .18

DTV Signal Strength . . . . . . . . . . . . . . . . . . . . .19

Channel Label Setup . . . . . . . . . . . . . . . . . . . .19

Main Picture Source Selection . . . . . . . . . . . . .20

Front LED (Light Emitting Diode) Display . . . . .20

Video Menu Options

EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .21

Manual Picture Control (User Option) . . . . . . . .21

Color Temperature Control . . . . . . . . . . . . . . . .21

Video Preset . . . . . . . . . . . . . . . . . . . . . . . . . .21

Audio Menu Options

Audio Language . . . . . . . . . . . . . . . . . . . . . . . .22

EZ SoundRite / EZ Sound . . . . . . . . . . . . . . . . .22

Manual Sound Control (User Option) . . . . . . . .22

Stereo/SAP Broadcasts Setup . . . . . . . . . . . . .23

Front Surround . . . . . . . . . . . . . . . . . . . . . . . . . 23

TV Speakers On/Off Setup . . . . . . . . . . . . . . . .23

. .16

Time Menu Options

Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .24

Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .24

On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .24

Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . . . .25

Option Menu Features

Aspect Ratio . . . . . . . . . . . . . . . . . . . . . . . . . . .26

Caption / Caption Mode . . . . . . . . . . . . . . . . . .27

Caption Option / EZ Demo . . . . . . . . . . . . . . . .28

ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .28

White Wash . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Low power . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .29

Lock Menu Options

Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .31

PIP (Picture-in-Picture)/Twin Picture

Watching PIP/POP/Twin Picture . . . . . . . . . . . ..32

Selecting an Input Signal Source for PIP/Twin Picture

Swapping PIP/Twin Picture . . . . . . . . . . . . . . . .32

TV Program Selection for PIP . . . . . . . . . . . . . .32

Moving the PIP sub picture . . . . . . . . . . . . . . . . 33

Adjusting Main and Sub Picture Sizes for Twin Picture . .33 POP (Picture-out-of-Picture: Channel Scan) . . .33

External Control Device Setup . . . . . . . . . . . . . . . .34~38

IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .39~40

Programming the Remote . . . . . . . . . . . . . . . . . . . . . .41

Programming Codes . . . . . . . . . . . . . . . . . . . . . . .42~43

Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .44

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .45

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .46

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .47~48

. .32

Setup and Operation Checklist

Setup and Operation Checklist (See pages 11~15 for available connection and operational setup options.)

1. Unpack TV and all accessories.

2. Connect all external video and audio equipment. see pages 12 ~ 14.

3 Install batteries in remote control.

See page 9.

4. Turn TV on. See page 17.

After reading this manual, keep it handy for future reference.

5. Turn video source equipment on.

6. Select viewing source for TV. See page 20.

7. Fine-tune source image and sound to your personal preference or as required by source. See pages 21 ~ 23.

8. Additional features set up See Contents above.

Owner’s Manual 5

Introduction

What is a Plasma Display Panel (PDP)?

A plasma display panel is the latest display technology and the best way to achieve flat panel displays with excellent image quality and large screen sizes that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be also be viewed as a series of fluorescent lamps.

How does it work?

PDP is an array of cells, known as pixels, which are comprised of 3 sub pixels, corresponding to the colors red, green, and blue. Gas in a plasma state is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue). These phosphors are the same types used in Cathode Ray Tube (CRT) devices such as televisions and common computer monitors.

You get the rich, dynamic colors that you expect. Each sub-pixel is individually controlled by advanced electronics to produce over 16 million different colors. All of this means that you get perfect images that are easily viewable in a display that is less than 5 inches thick.

160° - Wide angle range of vision

Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room who can see the screen.

Wide Screen

The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater.

Multimedia

Connect your plasma display to a PC and you can use it for conferencing, games, and Internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously.

Versatile

The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will not fit.

The PDP Manufacturing Process: a few minute colored dots may be present on the PDP screen

The PDP (Plasma Display Panel), which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several tiny, minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products. The tiny dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology minimizes these cell defects during the manufacture and operation of this product.

Cooling Fan Noise

In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP. The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned.

6 Plasma TV

Controls

TV/VIDEO

ON/OFF

S-VIDEO

A/V INPUT 2

VIDEO

AUDIO

L/MONO

VOL

TV/VIDEO MENU VOL CH

ON/OFF S-VIDEO VIDEO AUDIO

L/MONO

A/V INPUT 2

Controls

- This is a simplified representation of front panel. Here shown may be somewhat different from your TV.

- This manual explains the features available on the DU-50PZ60/70 series TVs.

Front Panel Controls

Introduction

Remote Control Sensor

Power Button

AUDIO Input

Use to connect to hear stereo sound from an external device.

VIDEO Input

Connects the video signal from a video device.

S-VIDEO Input

A connection available to provide better picture quality than the video input.

TV/VIDEO Button

MENU Button

Power Standby Indicator

Illuminates red in standby mode, Illuminates green when the TV is turned on.

CHANNEL (E, D) Buttons

VOLUME (

F,G) Buttons

Owner’s Manual 7

Introduction

RGB INPUT

Antenna1 Antenna 2

AUDIO INPUT

DVI INPUT

S-VIDEO

REMOTE

CONTROL

AC INPUT

EXTERNAL SPEAKER

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

(MONO)

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

RL R L

COMPONENT1 INPUT

OUTPUT

RS-232C INPUT

(CONTROL/SERVICE)

Connection Options

Back Connection Panel

DVD/DTV Input (Component 1-2)

Connect a component video/audio device to these jacks.

Digital Audio (DVI: Digital Visual

Interface/Component1) Input/

Digital Audio Output

Connect digital audio from various types

of equipment. Note: In standby mode,

these ports will not work.

S-Video Input

Connect S-Video out from an S-VIDEO device to the S-VIDEO input.

Monitor Output

Connect a second TV or

Monitor.

Remote Control Port

Connect your wired remote control here.

Antenna 1-2 Inputs

Connect cable or antenna

Connect audio/video output from an

external device to these jacks.

signals to the TV, either

Audio/Video Input 1

directly or through your cable box. For DTV use Antenna 2 only.

RGB Input/Audio Input/DVI Input

* For further information, refer to ‘Speaker &

External Speaker (8 ohm Output)

Connect to optional external speaker(s).

Connect the monitor output connector from a PC to the appropriate input port.

This TV operates on an AC power. The voltage is indi-

cated on the Specifications page. Never attempt to oper-

- This manual explains the features available on the DU-50PZ60/70 series TVs.

8 Plasma TV

Speaker Stand’ manual.

Power Cord Socket

ate the TV on DC power.

LIGHT

TV/VIDE

MODE

COMP/RGB/DVI

MUTE

SURF

VOL CH

INFO

SAP

RATIO

SOUND VIDEO

EXIT

PLAY PAUSE STOP RECORD

PIP PIPCH- PIPCH+ PIPINPUT

FREEZE

ADJUST

ZOOM SIGNAL SWAP

REW FF SKIP

POWER

TIME

FLASHBK

Remote Control Key Functions

- When using the remote control, aim it at the remote control sensor on the TV.

Installation

LIGHT

Illuminates the remote control buttons.

TV/VIDEO

Selects: DTV, Analog, Video1-2,

Component 1-2, RGB-DTV (or RGB-PC),

DVI-DTV (or DVI-PC) input sources.

COMP/RGB/DVI

Selects: Component 1-2, RGB-DTV (or RGB-

PC), DVI-DTV (or DVI-PC) input sources.

NUMBER buttons

DASH

Used to enter a program number for multiple

program channels such as 2—1,2—2,etc.

MUTE

Switches the sound on or off.

VOLUME UP/DOWN

Increases/decreases the sound level.

When you watch the TV, displays information

on top of the screen. Not available in

INFO

Component 1-2, RGB and DVI mode.

SAP

Selects MTS sound: Mono, Stereo, and SAP.

Change the audio language in DTV mode.

THUMBSTICK (Up/Down/Left/Right/OK)

Allows you to navigate the on-screen

menus and adjust the system settings to

your preference.

Brings up the main menu to the screen.

SOUND

Selects the sound appropriate

for the program's character.

FREEZE

Freezes the currently-viewed picture. Main

picture is frozen in PIP/Twin picturre mode.

Adjusts screen position, clock, and

ADJUST

phase in PC mode.

ZOOM

Enlarges the main picture size.

Displays the digital signal strength.

SIGNAL

MODE

Selects the remote operating mode: TV, VCR, DVD, CABLE, HDSTB or AUDIO. Select other operating modes, for the remote to operate external devices.

POWER

Turns your TV or any other programmed equipment on or off, depending on mode.

TIMER

Lets you select the amount of time before your TV turns itself off automatically.

FLASHBK

Tunes to the last channel viewed.

SURF

Use to scroll the Surf channel list.

CHANNEL UP/DOWN

Selects available channels found with EZ scan.

RATIO

Changes the aspect ratio.

Select a closed caption: Off, EZ Mute, and On.

EXIT

Clears all on-screen displays and returns to TV viewing from any menu.

VIDEO

Adjusts the factory preset picture according to the room.

VCR/DVD BUTTONS

Control some video cassette recorders or DVD player ("RECORD" button is not available for DVD player).

PIP

Switches between PIP, POP (Picture-out-ofPicture) and Twin picture modes.

PIPCH-/PIPCH+

Changes to next higher/lower PIP channel.

PIP INPUT

Selects the input source for the sub picture.

SWAP

Exchanges the PIP/main images.

Installing Batteries

• Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -).

• Install two 1.5V AAbatteries. Don’t mix old or used batteries with new ones.

Replace cover.

Owner’s Manual 9

Installation

1.5V

MODE

COMP/RGB/DVI

MUTE

SURF

VOL CH

INFO

SAP

RATIO

SOUNDVIDEO

EXIT

PLAY PAUSE STOPRECORD

PIP PIPCH- PIPCH+PIPINPUT

FREEZE

ADJUST

ZOOM SIGNALSWAP

REW FF SKIP

P O

W E R

T IM

E R

FLASHBK

Installation

Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product.

Owner’s Manual

Installation Instructions

Batteries

Power Cord

75Ω Round Cable

• The TV can be installed in various ways such as on a wall, or on a desktop etc.

• The TV is designed to be mounted horizontally. The speakers shown are optional.

GROUNDING

Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

all Mount: Horizontal installation

WWall Mount: Horizontal installation

Desktop Pedestal Installation

Remote Control

Power

Supply

Short-circuit

Breaker

For proper ventilation, allow a clearance of 4” on each side and 2” from the wall. Detailed installation instructions are available from your dealer, see the optional Wall Mounting Bracket Installation and Setup Guide.

2 inches

10 Plasma TV

4 inches

4 inches4 inches

4 inches

For proper ventilation, allow a clearance of 4” on each side and the top, 2.36” on the bottom, and 2” from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup Guide available from your dealer.

4 inches

2.36 inches

2 inches

RGB INPUT

AUDIO INPUT

DVI INPUT

DIGITAL AUDIO

(OPTICAL)

DVI

INPUT

COMPONENT1 INPUT

OUTPUT

(

)

External Equipment Connections

Antenna Connection

Analog and Digital TV signals provided on one antenna

- Antenna or Cable Service without a Cable Box Connections

- For optimum picture quality, adjust antenna direction if needed.

Multi-family Dwellings/Apartments (Connect to wall antenna socket)

Wall Antenna Socket

Bronze Wire

RF Coaxial Wire (75 ohm)

Antenna 2

RGB INPUT

AUDIO INPUT

DVI INPUT

Installation

DVI

COMPONENT1

OUTPUT

INPUT

DIGITAL AUDIO

OPTICAL

VHF Antenna UHF Antenna

Turn clockwise to tighten.

Outdoor

Antenna

Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)

Plasma TV

• In a poor signal area to improve picture quality, purchase and install a signal amplifier.

• If the antenna needs to be split for two TV’s, install a “2Way Signal Splitter” in the connections.

Signal

Amplifier

• If the antenna is not installed properly, contact your dealer for assistance.

Analog and Digital TV signals provided on two separate antennas

Wall Antenna Socket

RF Coaxial Wire (75 ohm)

Analog Antenna

Bronze Wire

Be careful not to bend the bronze wire when connecting the antenna.

Wall Antenna Socket

RF Coaxial Wire (75 ohm)

Turn clockwise to tighten.

Antenna1 Antenna 2

RGB INPUT

AUDIO INPUT

DVI INPUT

Digital Antenna

Bronze Wire

NOTE: If you are not sure of the type of signal(s) you are receiving, let EZ Scan complete all the channel signal-type searches.

The TV will let you know when the analog, cable, and digital channel scans are complete.

Owner’s Manual 11

Installation

RGB INPUT

Antenna 1 Antenna 2

AUDIO INPUT

DVI INPUT

S-VIDEO

REMOTE

CONTROL

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

RL R L

COMPONENT1 INPUT

OUTPUT

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

ANT OUT

ANT IN

(MONO)

RS-232C INPUT

(CONTROL/SERVICE)

RGB INPUT

Antenna 1 Antenna 2

AUDIO INPUT

DVI INPUT

S-VIDEO

REMOTE

CONTROL

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

RL R L

COMPONENT1 INPUT

OUTPUT

VCR

RF Cable

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

(MONO)

RS-232C INPUT

(CONTROL/SERVICE)

NOTE: All cables shown are not included with the TV

VCR Setup

- To avoid picture noise (interference), leave an adequate distance between the VCR and TV

- Use the ISM Method (on the Option menu) feature to avoid having a fixed image remain on the screen for a long period of time. Typically a frozen still picture from a VCR. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen.

Connection Option 1

Set VCR output switch to 3 or 4 and then tune

TV to the same channel number.

Connection Option 2

1. Connect the audio and video cables from the VCR's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input.

2. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner ’s manual.)

3. Select the input source with using the TV/VIDEO button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source)

Do not connect to both Video and S-Video at the same time.

VCR

Cable

TV Setup

Cable

TV Setup

- After subscribing to a cable TV service from a local provider and installing a converter, you can watch cable TV programming. The TV cannot display TV programming unless a TV tuner device or cable TV converter box is connected to the TV.

- For further information regarding cable TV service, contact your local cable TV service provider(s).

Connection Option 1

1. Select 3 or 4 with channel switch on cable box.

2. Tune the TV channel to the same selected output channel on cable box.

3. Select channels at the cable box or with the cable box remote control.

Connection Option 2

1. Connect the audio and video cables from the Cable Box's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to a Cable Box, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).

2. Select the input source with using the TV/VIDEO button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source)

3. Select your desired channel with the remote control for cable box.

12 Plasma TV

Cable Box

Installation

AUDIO VIDEO

S-VIDEO

REMOTE

CONTROL

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

DVD /DTV INPUT

COMPONENT 1

RL R L

(MONO)

RS-232C INPUT

(CONTROL/SERVICE)

S-VIDEO

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

RL R L

COMPONENT1 INPUT

OUTPUT

(R) AUDIO (L)

DIGITAL AUDIO

OPTICAL

(R) AUDIO (L)

S-VIDEO

RS-232C INPUT

(CONTROL/SERVICE)

S-VIDEO

(R) AUDIO (L) VIDEO

S-VIDEO

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

RL R L

COMPONENT1 INPUT

OUTPUT

(MONO)

RS-232C INPUT

(CONTROL/SERVICE)

External

A/V Source Setup

How to connect

Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).

How to use

1. Select the input source with using the TV/VIDEO button on the remote control. (If connected to A/V INPUT 1, select Video 1 input source).

2. Operate the corresponding external equipment. Refer to external equipment operating guide.

Monitor Out Setup

Camcorder

Video Game Set

The TV has a special signal output capability which allows you to hook up a second TV or monitor.

Connect the second TV or monitor to the TV’s MONITOR OUTPUT. See the Operating Manual of the second TV or monitor for further details regarding that device’s input settings.

NOTE

• Component, RGB-PC/RGB-DTV, DVI-PC/DVI-DTV, DTV input sources cannot be used for Monitor out.

DVD Setup

How to connect

1. Connect the DVD video outputs (Y, PB, PR) to the COMPONENT (Y, PB, PR) INPUT jacks on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure.

2. If your DVD only has an S-Video output jack, connect this to the SVIDEO input on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure.

NOTE: If your DVD player does not have component video output, use

S-Video.

How to use

1. Turn on the DVD player, insert a DVD.

2. Use the TV/VIDEO or COMP/RGB/DVI button on the remote control to select Component 1 or Component 2. (If connected to S-VIDEO, select the Video 1 or Video 2 external input source.)

3. Refer to the DVD player's manual for operating instructions.

• Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports

Video output ports on DVD player

on the TV

Y Y Y Y

B-Y

Cb P

NOTES

• Digital Audio will not work for Component 2 input source.

R-Y

• Digital Audio operation has priority if Digital Audio and AUDIO L/R are connected at the same time.

DVD

Owner’s Manual 13

Installation

RGB INPUT

Antenna 1 Antenna 2

AUDIO INPUT

DVI INPUT

S-VIDEO

REMOTE

CONTROL

AC INPUT

EXTERNAL SPEAKER

AUDIO INPUT

AUDIO VIDEO

VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

MONITOR OUTPUT

A/V

INPUT1

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

RL R L

COMPONENT1 INPUT

OUTPUT

(R) AUDIO (L)

RGB-DTV OUTPUT

DIGITAL AUDIO

OPTICAL

(R) AUDIO (L)

DVI-DTV OUTPUT

DIGITAL AUDIO

OPTICAL

(MONO)

RS-232C INPUT

(CONTROL/SERVICE)

RGB INPUT

AUDIO INPUT

DVI INPUT

AUDIO INPUT VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

COMPONENT1

INPUT

OUTPUT

HDSTB Setup

- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for DTV (480p,720p,1080i) mode.

or or

Digital Set-top Box

How to connect

Use the TV’s COMPONENT (Y, P video connections, depending on your set-top box connector. Then, make the corresponding audio connections.

B, PR) INPUT, RGB or DVI jack for

How to use

1. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)

2. Use TV/VIDEO or COMP/RGB/DVI on the remote control to select Component 1, Component 2, RGB-DTV, or DVI-DTV source.

Digital

Send the TV’s audio to external audio equipment (stereo system) via the Digital Audio Output Optical port.

Audio Output

Signal 480i 480p 720p 1080i

Component 1/2

Yes Yes Yes Yes

RGB-DTV,DVI-DTV

No Yes Yes Yes

How to connect

1. Connect one end of an optical cable to the TV Digital Audio Optical Output port.

2. Connect the other end of the optical cable to the digital audio optical input on the audio equipment.

3. Set the “ TV Speaker option - Off” in the AUDIO menu. Refer to page 23. See the external audio equipment instruction manual for operation.

Caution: Do not look into the optical output port.

Looking at the laser beam may damage your vision.

14 Plasma TV

Installation

RGB INPUT

Antenna 1 Antenna 2

AUDIO INPUT

DVI INPUT

AUDIO INPUT VIDEO INPUT

DIGITAL AUDIO

(OPTICAL)

COMPONENT 2

DVD /DTV INPUT

COMPONENT 1

DVI

INPUT

COMPONENT1 INPUT

OUTPUT

PC Setup

- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings. The TV sends configuration information (EDID) to the PC using the Video Electronics Standard Association (VESA) Display Data Channel (DDC) protocol.

- The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card. card, change the screen scanning rate for the graphic card accordingly.

How to connect

1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz.

2. Use the TV’s RGB INPUT or DVI (Digital Visual Interface) INPUT port for video connections, depending on your PC connector.

• If the graphic card on the PC does not output

analog and digital RGB simultaneously, connect only one of either RGB INPUT or DVI INPUT to display the PC on the TV.

• If the graphic card on the PC does output analog

and digital RGB simultaneously, set the TV to either RGB or DVI; (the other mode is set to Plug and Play automatically by the TV.)

3. Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.

How to use

1. Turn on the PC and the TV.

2. Turn on the display by pressing the POWER button on the TV's remote control.

3. Select RGB-PC or DVI-PC input source in main input option of SETUP menu. (Refer to P.20)

4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

NOTES: • Depending on the graphics card, DOS mode may not work if you use a DVI-I cable.

• Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become per-

manently imprinted on the screen. Use the Orbiter screen saver when possible.

• The synchronization input form for Horizontal and Vertical frequencies is separate.

Monitor Display Specifications (RGB-PC / DVI-PC Mode)

Resolution

640x350

720x400

640x480

Horizontal

Frequency(KHz)

31.468

37.861

31.469

37.927

31.469

37.861

37.500

43.269

Vertical

Frequency(Hz)

70.09

85.08

70.08

85.03

59.94

72.80

75.00

85.00

Resolution

Horizontal

Frequency(KHz)

35.156

800x600

37.879

48.077

46.875

53.674

48.363

1024x768

56.476

60.023

Vertical

Frequency(Hz)

56.25

60.31

72.18

75.00

85.06

60.00

70.06

75.02

Owner’s Manual 15

+ 33 hidden pages