LG Electronics DU-50PY10 User Manual

Please read this manual carefully and completely before operating your TV. Retain this manual for future reference. Record model number and serial number of the TV in the spaces provided below. See the label attached on the back cover and relate this information to your dealer if you require service.

Model Number : Serial Number :

MODELS: DU-50PY10

DU-60PY10

LG Electronics U.S.A., Inc.

TruSurround XT

PLASMA TV

OWNER’S MANUAL

2 Plasma TV

Warning

WARNING:

TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.

The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to

the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of impor-

tant operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING:

TO PREVENT FIRE OR SHOCK HAZARDS, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

POWER CORD POLARIZATION:

CAUTION: TO PREVENT ELECTRIC SHOCK, MATCH WIDE BLADE OF PLUG TO WIDE SLOT, FULLY INSERT.

NOTE TO CABLE/TV INSTALLER:

This reminder is provided to call the CATV system installer’s attention to Article 820-40 of the National Electric Code (U.S.A.). The code provides guidelines for proper grounding and, in particular, specifies that the cable ground shall be connected to the grounding system of the building, as close to the point of the cable entry as practical.

REGULATORY INFORMATION:

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.

• Increase the separation between the equipment and receiver.

• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

• Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

CAUTION:

Do not attempt to modify this product in any way without written authorization from LG Electronics. Unauthorized modification could void the user’s authority to operate this product.

COMPLIANCE:

The responsible party for this product’s compliance is: LG Electronics U.S.A., Inc 1000 Sylvan Avenue, Englewood Cliffs, NJ 07632 1-201-816-2000 http://www.lgusa.com

WARNING

RISK OF ELECTRIC SHOCK DO NOT OPEN

arning

Owner’s Manual 3

TV Guide On Screen Notices for U.S.A.

In the United States, the TV Guide On Screen system and other related marks are registered marks of Gemstar-TV Guide

On Screen system International, Inc. and/or one of its affiliates. In Canada,TV Guide On Screen system is a registered mark

of Transcontinental Inc., and is used under license by Gemstar-TV Guide On Screen system International, Inc.

The TV Guide On Screen system is protected by one or more of the following issued United States patents 6,498,895,

6,418,556, 6,331,877; 6,239,794; 6,154,203; 5,940,073; 4,908,713; 4,751,578; 4,706,121.

The TV Guide On Screen system is manufactured under license from Gemstar-TV Guide On Screen system International,

Inc. and/or one of its affiliates.

Digital Cable Compatibility

This digital television is capable of receiving basic analog, digital basic and digital premium cable television programming by

direct connection to a cable system providing such programming. A security card provided by your cable operator is required

to view encrypted digital programming. Certain advanced interactive digital cable services such as video-on-demand, cable

operator enhanced program the TV Guide On Screen system, and data enhanced television service may require the use of

a set top box. For more information contact your local cable operator.

Use of the CableCARD

TradeMark.

“CableCARD

is a trademark of Cable Television Laboratories, Inc.”

4 Plasma TV

Safety Instructions

Important safeguards for you and your new product

Your product has been manufactured and tested with your safety in mind. However, improper use can result in electrical shock or fire hazards. To avoid defeating the safeguards that have been built into your new product, please read and observe the following safety points when installing and using your new product, and save them for future reference.

Observing the simple precautions discussed in this manual can help you get many years of enjoyment and safe operation that are built into your new product.

This product complies with all applicable U.S. Federal safety requirements, and those of the Canadian Standards Association.

1. Read Instructions

All the safety and operating instructions should be read before the product is operated.

2. Follow Instructions

All operating and use instructions should be followed.

3. Retain Instructions

The safety and operating instructions should be retained for future reference.

4. Heed Warnings

All warnings on the product and in the operating instructions should be adhered to.

5. Cleaning

Unplug this product from the wall outlet before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.

6. Water and Moisture

Do not use this product near water, for example, near a bath tub, wash bowl, kitchen sink, or laundry tub, in a wet basement, or near a swimming pool.

7. Accessories, Carts, and Stands

Do not place this product on a slippery or tilted surface, or on an unstable cart, stand, tripod, bracket, or table. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product. Use only with a cart, stand, tripod, bracket, or table recommended by the manufacturer, or sold with the product. Any mounting of the product should follow the manufacturer’s instructions, and should use a mounting accessory recommended by the manufacturer.

8. Transporting Product

A product and cart combination should be moved with care. Quick stops, excessive force, and uneven surfaces may cause the product and cart combination to overturn.

9. Attachments

Do not use attachments not recommended by the product manufacturer as they may cause hazards.

10. Ventilation

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from overheating, and these openings must not be blocked or covered. The openings should never be blocked by placing the product on a bed, sofa, rug, or other similar surface. This product should not be placed in a built-in installation such as a bookcase or rack unless proper ventilation is provided or the manufacturer’s instructions have been adhered to.

11. Power Sources

This product should be operated only from the type of power source indicated on the marking label. If you are not sure of the type of power supply to your home, consult your product dealer or local power company. For products intended to operate from battery power, or other sources, refer to the operating instructions.

12. Power-Cord Polarization

This product is equipped with a three-wire grounding type plug, a plug having a third (grounding) pin. This plug will only fit into the grounding-type power outlet. This is a safety feature. If you are unable to insert the plug into the outlet, contact your electrician to replace your obsolete outlet. Do not defeat the safety purpose of the grounding-type plug.

13. Power-Cord Protection

Power-supply cords should be routed so that they are not likely to be walked on or pinched by items placed upon or against them, paying particular attention to cords at plugs, convenience receptacles, and the point where they exit from the product.

PORTABLE CART WARNING

Safety Instructions

Owner’s Manual 5

Safety Instructions

Antenna Lead in Wire

Antenna Discharge Unit (NEC Section 810-20)

Grounding Conductor (NEC Section 810-21)

Ground Clamps

Power Service Grounding Electrode System (NEC Art 250, Part H)

Ground Clamp

Electric Service

Equipment

Example of Grounding According to National Electrical Code Instructions

NEC - National Electrical Code

14. Outdoor Antenna Grounding

If an outside antenna or cable system is connected to the product, be sure the antenna or cable system is grounded so as to provide some protection against voltage surges and built-up static charges. Article 810 of the National Electrical Code (U.S.A.), ANSI/ NFPA 70 provides information with regard to proper grounding of the mast and supporting structure, grounding of the lead-in wire to an antenna discharge unit, size of grounding conductors, location of antenna-discharge unit, connection to grounding electrodes, and requirements for the grounding electrode.

15. Lightning

For added protection for this product (receiver) during a lightning storm, or when it is left unattended and unused for long periods of time, unplug it from the wall outlet and disconnect the antenna or cable system. This will prevent damage to the product due to lightning and power-line surges.

16. Power Lines

An outside antenna system should not be located in the vicinity of overhead power lines or other electric light or power circuits, or where it can fall into such power lines or circuits. When installing an outside antenna system, extreme care should be taken to keep from touching such power lines or circuits as contact with them might be fatal.

17. Overloading

Do not overload wall outlets and extension cords as this can result in a risk of fire or electric shock.

18. Object and Liquid Entry

Never push objects of any kind into this product through openings as they may touch dangerous voltage points or short-out parts that could result in a fire or electric shock. Never spill liquid of any kind on the product.

19. Servicing

Do not attempt to service this product yourself as opening or removing covers may expose you to dangerous voltage or other hazards. Refer all servicing to qualified service personnel.

20. Damage Requiring Service

Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:

a. If the power-supply cord or plug is damaged. b. If liquid has been spilled, or objects have fallen into the

product. c. If the product has been exposed to rain or water. d. If the product does not operate normally by following the

operating instructions. Adjust only those controls that are

covered by the operating instructions as an improper

adjustment of other controls may result in damage and

will often require extensive work by a qualified technician

to restore the product to its normal operation. e. If the product has been dropped or the cabinet has been

damaged. f. If the product exhibits a distinct change in performance.

21. Replacement Parts

When replacement parts are required, be sure the service technician has used replacement parts specified by the manufacturer or have the same characteristics as the original part. Unauthorized substitutions may result in fire, electric shock, or other hazards.

22. Safety Check

Upon completion of any service or repairs to this product, ask the service technician to perform safety checks to determine that the product is in proper operating condition.

23. Wall or Ceiling Mounting

The product should be mounted to a wall or ceiling only as recommended by the manufacturer. The product may slide or fall, causing serious injury to a child or adult, and serious damage to the product.

24. Heat

The product should be situated away from heat sources such as radiators, heat registers, stoves, or other products (including amplifiers) that produce heat.

Safety Instructions continued

6 Plasma TV

Contents

After reading this manual, keep it handy for future reference.

Warnings . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .2

Digital Cable Compatibility . . . . . . . . . . . . . . . . . . . . . . . . .3

Safety Instructions . . . . . . . . . . . . . . . . . . . . . . . . . . . . .4~5

Introduction

Controls . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .8

Connection Options . . . . . . . . . . . . . . . . . . . . . .9

Remote Control Key Functions . . . . . . . . . . . . 10

Installation

Joining the TV assembly to the wall to protect the set tum-

bling . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .11

Installation Instructions . . . . . . . . . . . . . . . . . . . . .12

External Equipment Connections . . . . . . . . . .13~18

Antenna or Cable Connection . . . . . . . . . . .13~14

VCR Setup . . . . . . . . . . . . . . . . . . . . . . . . . . .14

External A/V Source Setup . . . . . . . . . . . . . . . .15

DVD Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . .15

CableCARD

Setup . . . . . . . . . . . . . . . . . . . . .16

HDSTB Setup . . . . . . . . . . . . . . . . . . . . . . . . .16

PC Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . .17

Monitor Out Setup . . . . . . . . . . . . . . . . . . . . . .18

Digital Audio Output . . . . . . . . . . . . . . . . . . . . .18

HDMI/DVI (VIDEO) . . . . . . . . . . . . . . . . . . . . .19~21

TV Guide On Screen Setup . . . . . . . . . . . . . .22~31

IEEE 1394 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .32~36

TV Guide On Screen®System . . . . . . . . . . . . . .37~55

Operation

Screen Setup for PC mode

Adjustments for screen Position, Size, and Phase

. .56

On-screen Menus Language Selection . . . . . . . . .57

Setup Menu Options

EZ Scan (Channel Search) . . . . . . . . . . . . . . . .58

Manual Scan . . . . . . . . . . . . . . . . . . . . . . . . . .58

Channel Edit . . . . . . . . . . . . . . . . . . . . . . . . . . .59

DTV Signal Strength . . . . . . . . . . . . . . . . . . . . .59

Channel Label Setup . . . . . . . . . . . . . . . . . . . .60

Main Picture Source Selection . . . . . . . . . . . . .60

Aux.Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Video Menu Options

EZ Picture . . . . . . . . . . . . . . . . . . . . . . . . . . . .61

Manual Picture Control (Off Option) . . . . . . . . .61

Color Temperature Control . . . . . . . . . . . . . . . .61

XD . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .62

Video Preset . . . . . . . . . . . . . . . . . . . . . . . . . .62

Audio Menu Options

Audio Language . . . . . . . . . . . . . . . . . . . . . . . .63

EZ SoundRite / EZ Sound . . . . . . . . . . . . . . . . .63

Manual Sound Control (off Option) . . . . . . . . . .63

Front Surround . . . . . . . . . . . . . . . . . . . . . . . . .64

TV Speakers On/Off Setup . . . . . . . . . . . . . . . .64

Stereo/SAP Broadcasts Setup . . . . . . . . . . . . .64

Time Menu Options

Auto Clock Setup . . . . . . . . . . . . . . . . . . . . . . .65

Manual Clock Setup . . . . . . . . . . . . . . . . . . . . .65

On/Off Timer Setup . . . . . . . . . . . . . . . . . . . . .65

Sleep Timer / Auto Off . . . . . . . . . . . . . . . . . . . .66

Option Menu Features

Aspect Ratio Control . . . . . . . . . . . . . . . . . . . . .67

Cinema Mode Setup . . . . . . . . . . . . . . . . . . . . .67

Caption . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .68

Caption / Text . . . . . . . . . . . . . . . . . . . . . . . . . .68

Caption Option / Demo . . . . . . . . . . . . . . . . . . .69

ISM Method . . . . . . . . . . . . . . . . . . . . . . . . . . .70

Low Power . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Split Zoom . . . . . . . . . . . . . . . . . . . . . . . . . . . .71

Lock Menu Options

Parental Lock Setup . . . . . . . . . . . . . . . . . . . . .73

CableCARDTMFunction

Cable menu options . . . . . . . . . . . . . . . . . . . . .74

Scrambled channel . . . . . . . . . . . . . . . . . . . . . .74

Cable Channel List . . . . . . . . . . . . . . . . . . . . . .75

Emergency Alert Message . . . . . . . . . . . . . . . .75

Remote Control

PIP (Picture-in-Picture)/Twin Picture . . . . . . . . . ..76

Watching PIP/POP/Twin Picture . . . . . . . . . . . ..76

Selecting an Input Signal Source for PIP/Twin Picture

. .76

Swapping PIP/Twin Picture . . . . . . . . . . . . . . . .76

TV Program Selection for PIP . . . . . . . . . . . . . .76

Moving the PIP sub picture . . . . . . . . . . . . . . . .77

Adjusting Main and Sub Picture Sizes for Twin Picture . .77 POP (Picture-out-of-Picture: Channel Scan) . . .77

Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .78

EZ Mute . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .79

External Control Device Setup . . . . . . . . . . . . . . . .80~84

IR Codes . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .85~86

Programming the Remote . . . . . . . . . . . . . . . . . . . . . .87

Programming Codes . . . . . . . . . . . . . . . . . . . . . . .88~89

Troubleshooting Checklist . . . . . . . . . . . . . . . . . . . . . .90

Maintenance . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .91

Product Specifications . . . . . . . . . . . . . . . . . . . . . . . . .92

Warranty . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .95~96

Contents

Setup and Operation Checklist

Setup and Operation Checklist (See pages 11~18 for available connection and operational setup options.)

1. Unpack TV and all accessories.

2. Connect all external video and audio equipment. see pages 13~ 18.

3 Install batteries in remote control.

See page 10.

4. Turn TV on. See page 57.

5. Turn video source equipment on.

6. Select viewing source for TV. See pages 60.

7. Fine-tune source image and sound to your personal preference or as required by source. See pages 61~ 64.

8. Additional features set up See Contents above.

Owner’s Manual 7

Introduction

What is a Plasma Display Panel (PDP)?

A plasma display panel is the latest display technology and the best way to achieve flat panel displays with excellent image quality and large screen sizes that are easily viewable. The PDP can be thought of as a descendant of the neon lamp and it can be also be viewed as a series of fluorescent lamps.

How does it work?

PDP is an array of cells, known as pixels, which are comprised of 3 sub pixels, corresponding to the colors red, green, and blue. Gas in a plasma state is used to react with phosphors in each sub-pixel to produce colored light (red, green, or blue). These phosphors are the same types used in Cathode Ray Tube (CRT) devices such as televisions and common computer monitors.

You get the rich, dynamic colors that you expect. Each sub-pixel is individually controlled by advanced electronics to produce over 16 million different colors. All of this means that you get perfect images that are easily viewable in a display that is less than 5 inches thick.

160° - Wide angle range of vision

Your flat panel plasma screen offers an exceptionally broad viewing angle -- over 160 degrees. This means that the display is clear and visible to viewers anywhere in the room who can see the screen.

Wide Screen

The screen of the Plasma Display is so wide that your viewing experience is as if you are in a theater.

Multimedia

Connect your plasma display to a PC and you can use it for conferencing, games, and Internet browsing. The Picture-in-Picture feature allows you to view your PC and video images simultaneously.

Versatile

The light weight and thin size makes it easy to install your plasma display in a variety of locations where conventional TVs will not fit.

The PDP Manufacturing Process: a few minute colored dots may be present on the PDP screen

The PDP (Plasma Display Panel), which is the display device of this product is composed of 0.9 to 2.2 million cells. A few cell defects will normally occur in the PDP manufacturing process. Several tiny, minute colored dots visible on the screen should be acceptable. This also occurs in other PDP manufacturers' products. The tiny dots appearing does not mean that this PDP is defective. Thus a few cell defects are not sufficient cause for the PDP to be exchanged or returned. Our production technology minimizes these cell defects during the manufacture and operation of this product.

Cooling Fan Noise

In the same way that a fan is used in a PC computer to keep the CPU (Central Processing Unit) cool, the PDP is equipped with cooling fans to cool the Monitor and improve its reliability. Therefore, a certain level of noise could occur while the fans are operating and cooling the PDP. The fan noise doesn't have any negative effect on the PDP's efficiency or reliability. The noise from these fans is normal during the operation of this product. We hope you understand that a certain level of noise from the cooling fans is acceptable and is not sufficient cause for the PDP to be exchanged or returned.

8 Plasma TV

Introduction

TV/VIDEO

VOL CH

POWER

TV GUIDE

POWER

Controls

- This is a simplified representation of front panel. Here shown may be somewhat different from your TV.

Front Panel Controls

TV/VIDEO

VOL

TV GUIDE

MENU Button

TV/VIDEO Button

POWER Button

VOLUME (F,G) Buttons

CHANNEL (E, D) Buttons

INDEX

Switches LED Display on or off.

TV GUIDE Button

Remote Control

Sensor

TruSurround XTruSurround XT

Power Indicator

Illuminates orange in standby mode, Illuminates green when the TV is turned on.

(If power isn’t turn on in red, contact your service center.)

Owner’s Manual 9

Introduction

Connection Options

- This manual explains the features available on the DU-50PY10 series TVs.

S-VIDEO VIDEO

L / MONO

AUDIO

FRONT A/V INPUT

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

CABLE

HDMI / DVI(VIDEO)

Cable

ANTENNA

AC INPUTAC INPUT

Back Connection Panel

Antenna Inputs

Connect antenna signals to the TV, either directly or through your cable box.

RGB/AUDIO INPUT

Connect the monitor output connector from a PC to the appropriate input port.

Digital Audio (DVI: Digital

Visual

Interface/Component2)

Input/

Digital Audio Output

Connect digital audio from

various types of equipment.

Note: In standby mode,

these ports will not work.

DVD/DTV Input

(Component 1-2)

Connect a component

video/audio device to

these jacks.

Monitor Output

Connect a second

TV or Monitor.

Remote Control Port

Connect your wired remote control here.

S-Video Input

Connect S-Video out from an S-VIDEO device to the SVIDEO input.

IEEE1394

Connect DVHS or MicroMV to IEEE1394 Connector.

CABLE Inputs

Connect cable

signals to the TV,

either directly or

through your

cable box.

RS-232C INPUT (CONTROL/SERVICE) PORT

Connect to the RS-232C port on a PC.

CableCARD™

Used for CableCARD™ received Cable Service Provider.

G-LINK

Connect an IR controller to this jack.

HDMI/DVI(VIDEO)

Connect a HDMI/DVI(Video) signal to this jack.

S-VIDEO Input

A connection available to provide better picture quality than the video input.

VIDEO Input

Connects the video signal from a video device.

AUDIO Input

Use to connect to hear stereo sound from an external device.

Power Cord Socket

This TV operates on an AC power. The voltage is indi-

cated on the Specifications page. Never attempt to oper-

ate the TV on DC power.

Audio/Video Input

Connect audio/video output from an external device to these jacks.

10 Plasma TV

Installation

- When using the remote control, aim it at the remote control sensor on the TV.

SKIP

LIGHT

TV/VIDE

MODE

COMP/RGB/HDMI

MUTE

SURF

VOL CH

PGUP

PGDN

INFO

SAP

RATIO

TV GUIDE

TIMER

EXIT

PLAY

PAUSE STOP

RECORD

PIP PIPCH- PIPCH+ PIPINPUT

ENTER

SIGNAL SWAP

REW FF

POWER

1394

FLASHBK

VIDEO

SOUND

ADJUST

DAY +

DAY -

FREEZE

ZOOM

LIGHT

Illuminates the remote control buttons.

TV/VIDEO

Selects: DTV, Analog, Video, Front Video,

Component 1-2, RGB-DTV (or RGB-PC),

HDMI/DVI input sources.

COMP/RGB/HDMI

Selects: Component 1-2, RGB-DTV (or RGB-

PC), HDMI/DVI input sources.

NUMBER buttons

DASH

Uses to enter a program number for multiple

program channels such as 2-1,2-2,etc.

MUTE

Switches the sound on or off.

(Refer to p.79)

VCR/DVD BUTTONS

Control some video cassette recorders or DVD player. ("RECORD" button is not available for DVD player.) Selects the frequency setting in the recording: Once, Regularly, Weekly, Off.("RECORD" button only)

RATIO

Changes the aspect ratio.

MODE

Selects the remote operating mode: TV, VCR, DVD, CABLE, HDSTB or AUDIO. Select other operating modes, for the remote to operate external devices.

POWER

Turns your TV or any other programmed equipment on or off, depending on mode.

1394 (Refer to p.32-36)

SURF

Use to scroll the Surf channel.

Select a closed caption: Off, CC1~4, Text1~4.

FLASHBK

Tunes to the last channel viewed.

THUMBSTICK (Up/Down/Left/Right/ENTER)

Allows you to navigate the on-screen menus

and adjust the system settings to your pref-

erence.

CHANNEL UP/DOWN

Selects available channels found with EZ scan.

PAGE UP/PAGE DOWN

Moves from one full set of screen information to the next one.

EXIT

Clears all on-screen displays and returns to TV viewing from any menu.

TIMER

Lets you select the amount of time before your TV turns itself off automatically.

VOLUME UP/DOWN

Increases/decreases the sound level.

SAP

Selects MTS sound: Mono, Stereo, and SAP in Analog mode. Change the audio language

in DTV mode.

Brings up the main menu to the screen.

Enters or exits a Panel Menu in the TV Guide On

Screen system.

INFO

When you watch the TV, information displays

on top of the screen. Not available in

Component 1-2, RGB and HDMI/DVI

mode.(Refer to p.78)

TV GUIDE

Brings up the TV Guide On Screen system to

the screen.

PIP

Switches between PIP, POP (Picture-out-ofPicture) and Twin picture modes. Switches the video window locking or unlocking in the Listings Grid.

PIPCH-/PIPCH+

Changes to next higher/lower PIP channel.

PIP INPUT

Selects the input source for the sub picture.

SWAP

Exchanges the main/sub images in PIP/Twin picture mode.

VIDEO

Adjusts the factory preset picture

depending on the viewing environment.

ADJUST

Adjusts screen position, size, and

phase in PC mode.

SOUND

Selects the sound appropriate

for the program's character.

SIGNAL

Displays the digital signal strength.

Installing Batteries

• Open the battery compartment cover on the back side and install the batteries matching correct polarity (+ with +, - with -).

• Install two 1.5V AA batteries. Don’t mix old or used batteries with new ones.

Replace cover.

Remote Control Key Functions

FREEZE

Freezes the currently-viewed picture. Main pic-

ture is frozen in PIP/Twin picture mode.

ZOOM

Enlarges the main picture size.

DAY+/DAY-

Moves forward or backward in 24 hour increments in the Listings Grid.

Owner’s Manual 11

Installation

Owner’s Manual

1.5V

Batteries

Power Cord

MODE

COMP/RGB/DVI

MUTE

SURF

VOL CH

INFO

SAP

RATIO

SOUNDVIDEO

EXIT

PLAY PAUSE STOP RECORD

PIP PIPCH- PIPCH+PIPINPUT

FREEZE

ADJUST

ZOOM SIGNAL SWAP

REW FF SKIP

O W

E R

T IM

FLASHBK

75Ω Round Cable

Ensure that the following accessories are included with your plasma display. If an accessory is missing, please contact the dealer where you purchased the product.

- Secure the TV assembly by joining it to a wall by using the TV/Wall brackets.

Joining the TV assembly to the wall to protect the set tumbling

• After the set must be mounted on s desk top, install the TV brackets on the TV as shown.

Install the TV brackets on the TV as shown.

Insert the 2 bolts and tighten securely, in the upper holes on the bracket. Install the wall brackets on the wall with 4 bolts*, (not supplied with the product), as shown. Match the height of the TV brackets and the wall brackets. Check to be sure the brackets are tightened securely.

• Secure the TV assembly to the wall with strong strings or wound wire cables, (not supplied with the product), as shown.

2-TV brackets

2-Wall brackets

4-TV bracket bolts(50”)

G-LINK Cable

2-TV bracket bolts(60”)

12 Plasma TV

Installation

Installation Instructions

• The TV can be installed in various ways such as on a wall, or on a desktop etc.

• The TV is designed to be mounted horizontally. The speakers shown are optional.

GROUNDING

Ensure that you connect the grounding / earth wire to prevent possible electric shock. If grounding methods are not possible, have a qualified electrician install a separate circuit breaker. Do not try to ground the unit by connecting it to telephone wires, lightening rods, or gas pipes.

Power

Supply

Short-circuit

Breaker

WWall Mount: Horizontal installation

all Mount: Horizontal installation

For proper ventilation, allow a clearance of 4” on each side and 2” from the wall. Detailed installation instructions are available from your dealer, see the optional Wall Mounting Bracket Installation and Setup Guide.

Desktop Pedestal Installation

For proper ventilation, allow a clearance of 4” on each side and the top, 2.36” on the bottom, and 2” from the wall. Detailed installation instructions are included in the optional Desktop Stand Installation and Setup Guide available from your dealer.

4 inches

4 inches4 inches

4 inches

2 inches

4 inches

2.36 inches

2 inches

Owner’s Manual 13

Installation

Antenna or Cable Connection

External Equipment Connections

- Wall Antenna Socket or Outdoor Antenna without a Cable Box Connections

- For optimum picture quality, adjust antenna direction if needed.

1. Analog and Digital TV signals provided on antenna

2. Analog and Digital TV signals provided on cable

AC INPUT

Multi-family Dwellings/Apartments (Connect to wall antenna socket)

Single-family Dwellings /Houses (Connect to wall jack for outdoor antenna)

Outdoor Antenna

Wall Antenna Socket

VHF Antenna

UHF Antenna

RF Coaxial Wire (75 ohm)

Bronze Wire

Turn clockwise to tighten.

Bronze Wire

Be careful not to bend the bronze wire when connecting the antenna.

Digital Antenna

Bronze Wire

Cable TV Wall Jack

RF Coaxial Wire (75 ohm)

CABLE

Cable

ANTENNA

CABLE

14 Plasma TV

Installation

- To avoid picture noise (interference), leave an adequate distance between the VCR and TV

- Use the ISM Method (on the Option menu) feature to avoid having a fixed image remain on the screen for a long period of time. If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible on the screen.

Connection Option 1

Set VCR output switch to 3 or 4 and then tune

TV to the same channel number.

Connection Option 2

1. Connect the audio and video cables from the VCR's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to VCR, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red). If you connect an S-VIDEO output from VCR to the S-VIDEO input, the picture quality is improved; compared to connecting a regular VCR to the Video input.

2. Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.)

3. Select the input source with using the TV/VIDEO button on the remote control. (If connected to A/V INPUT , select Video input source)

Do not connect to both Video and S-Video at the same time.

VCR Setup

AC INPUTAC INPUT

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

ANT OUT

ANT IN

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

CABLE

HDMI / DVI(VIDEO)

Cable

ANTENNA

VCR Rear

Note: The TV will let you know when the analog, cable, and digital channel scans are complete.

• In a poor signal area to improve picture quality, purchase and install a signal amplifier.

• If the antenna needs to be split for two TV’s, install a “2Way Signal Splitter” in the connections.

• If the antenna is not installed properly, contact your dealer for assistance.

3. Analog and Digital TV signals provided on cable and antenna

Antenna

RF Coaxial Wire (75 ohm)

Analog Antenna

Bronze Wire

Turn clockwise to tighten.

Cable TV Wall Jack

RF Coaxial Wire (75 ohm)

CABLE

Cable

ANTENNA

AC INPUT

Signal

Amplifier

Owner’s Manual 15

Installation

• Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

How to connect

Connect the audio and video cables from the external equipment's output jacks to the TV input jacks, as shown in the figure. When connecting the TV to external equipment, match the jack colors (Video = yellow, Audio Left = white, and Audio Right = red).

How to use

1. Select the input source with using the TV/VIDEO button on

the remote control. (If connected to A/V INPUT , select Video input source).

2. Operate the corresponding external equipment. Refer to external equipment operating guide.

Component ports

on the TV

Video output ports on DVD player

Y Y Y Y

B-Y

Cb P

R-Y

Cr PR

How to connect

1. Connect the DVD video outputs (Y, PB, PR) to the COMPONENT (Y, PB, PR) INPUT jacks on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure.

2. If your DVD only has an S-Video output jack, connect this to the S-VIDEO input on the TV and connect the DVD audio outputs to the AUDIO INPUT jacks on the TV, as shown in the figure.

NOTE: If your DVD player does not have component video output, use S-Video.

How to use

1. Turn on the DVD player, insert a DVD.

2. Use the TV/VIDEO or COMP/RGB/HDMI button on the remote control to select Component 1 or Component 2. (If connected to S-VIDEO, select the Video or Front Video external input source.)

3. Refer to the DVD player's manual for operating instructions.

External

A/V Source Setup

DVD Setup

CABLE

Cable

ANTENNA

AC INPUT

AUDIO VIDEO

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

HDMI / DVI(VIDEO)

AC INPUTAC INPUT

(R) AUDIO (L)

DIGITAL AUDIO

OPTICAL

(R) AUDIO (L)

S-VIDEO

CABLE

Cable

ANTENNA

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

HDMI / DVI(VIDEO)

DVD

Camcorder

Video Game Set

Notes:

• Digital Audio will not work for Component 1 input source.

• Digital Audio operation has priority if Digital Audio and AUDIO L/R are connected at the same time.

16 Plasma TV

Installation

- This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you do receive Digital signals from a digital set-top box or other digital external device, refer to the figure as shown below.

- This TV supports HDCP (High-bandwidth Digital Contents Protection) protocol for Digital Contents (480p,720p,1080i).

How to connect

Use the TV’s COMPONENT (Y, P

B, PR) INPUT, RGB or HDMI/DVI jack

for video connections, depending on your set-top box connector. Then, make the corresponding audio connections.

How to use

1. Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.)

2. Use TV/VIDEO or COMP/RGB/HDMI on the remote control to select Component 1, Component 2, RGB-DTV, or HDMI/DVI source.

HDSTB Setup

AC INPUTAC INPUT

(R) AUDIO (L)

RGB-DTV OUTPUT

(R) AUDIO (L)

DIGITAL AUDIO

OPTICAL

(R) AUDIO (L)

DVI-DTV OUTPUT

DIGITAL AUDIO

OPTICAL

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

HDMI / DVI(VIDEO)

CABLE

Cable

ANTENNA

HDMI-DTV OUTPUT

Digital Set-top Box

CableCARD

Setup

AC INPUTAC INPUT

CABLE

Cable

ANTENNA

How to use

Insert the CableCARD

received from Cable Service provider to

CableCARD

slot of TV back panel.

If Host or CableCARD

does not display on the screen, contact with Cable

service provider by phone.

Note :

• CableCARD

has the types of Motorola, Scientific Atlanta, SCM etc..

These 3 types of CableCARD

can be used for this PLASMA TV.

Signal 480i 480p 720p 1080i

Component 1/2

Yes Yes Yes Yes

RGB-DTV,HDMI/DVI

No Yes Yes Yes

Caution: When removing the CableCARD

, do not fall it as this may cause impact to the CableCARD

Owner’s Manual 17

Installation

How to connect

1. To get the best picture quality, adjust the PC graphics card to 1024x768, 60Hz.

2. Use the TV’s RGB INPUT or HDMI/DVI (Digital Visual Interface) INPUT port for video connections, depending on your PC connector.

• If the graphic card on the PC does not output analog and digital RGB simultaneously, connect only one of either RGB INPUT or DVI INPUT to display the PC on the TV.

• If the graphic card on the PC does output analog and digital RGB simultaneously, set the TV to either RGB or HDMI/DVI; (the other mode is set to Plug and Play automatically by the TV.)

3. Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.

How to use

1. Turn on the PC and the TV.

2. Turn on the display by pressing the POWER button on the TV's remote control.

3. Select RGB-PC or HDMI/DVI input source in main input option of SETUP menu. (Refer to P.59)

4. Check the image on your TV. There may be noise associated with the resolution, vertical pattern, contrast or brightness in PC mode. If noise is present, change the PC mode to another resolution, change the refresh rate to another rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphic card can not be changed, change the PC graphic card or consult the manufacturer of the PC graphic card.

NOTES: • Depending on the graphics card, DOS mode may not work if you use a HDMI to DVI cable.

• Avoid keeping a fixed image on the TV's screen for a long period of time. The fixed image may become permanently

imprinted on the screen. Use the Orbiter screen saver when possible.

• The synchronization input form for Horizontal and Vertical frequencies is separate.

PC Setup

AC INPUTAC INPUT

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

HDMI / DVI(VIDEO)

CABLE

Cable

ANTENNA

- This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

- The TV perceives 640x480, 60Hz as DTV 480p based on the PC graphic card, change the screen scanning rate for the graphic

card accordingly.

Resolution

640x350

720x400

640x480

800x600

Horizontal

Frequency(KHz)

31.468

37.861

31.469

37.927

31.469

37.861

37.500

43.269

70.09

85.08

70.08

85.03

59.94

72.80

75.00

85.00

35.156

37.879

48.077

46.875

53.674

48.363

56.476

60.023

56.25

60.31

72.18

75.00

85.06

60.00

70.06

75.02

Vertical

Frequency(Hz)

Resolution

Horizontal

Frequency(KHz)

Vertical

Frequency(Hz)

1024x768

Monitor Display Specifications (RGB-PC )

18 Plasma TV

Installation

Send the TV’s audio to external audio equipment (stereo system) via the Digital Audio Output (Optical) port.

How to connect

1. Connect one end of an optical cable to the TV Digital Audio (Optical) Output port.

2. Connect the other end of the optical cable to the digital audio (optical) input on the audio equipment.

3. Set the “ TV Speaker option - Off” in the AUDIO menu. Refer to

page 64. See the external audio equipment instruction manual for operation.

Caution: Do not look into the optical output port.

Looking at the laser beam may damage your vision.

Digital

Audio Output

Cable

ANTENNA

AC INPUT

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

HDMI / DVI(VIDEO)

The TV has a special signal output capability which allows you to hook up a second TV or monitor.

Connect the second TV or monitor to the TV’s MONITOR OUTPUT. See the Operating Manual of the second TV or monitor for further details regarding that device’s input settings.

Note

• Component, RGB-PC/RGB-DTV, HDMI/DVI, DTV input sources cannot be used for Monitor out.

Cable

ANTENNA

AC INPUT

S-VIDEO

(R) AUDIO (L) VIDEO

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

HDMI / DVI(VIDEO)

Monitor Out Setup

Resolution

640x480

800x600

Horizontal

Frequency(KHz)

31.469

37.861

37.500

35.156

37.879

48.077

46.875

59.94

72.80

75.00

56.25

60.31

72.18

75.00

48.363

56.476

60.023

60.00

70.06

75.02

Vertical

Frequency(Hz)

Resolution

Horizontal

Frequency(KHz)

Vertical

Frequency(Hz)

1024x768

Monitor Display Specifications (HDMI/DVI Mode)

Owner’s Manual 19

HDMI

HDMI/DVI (VIDEO)

-HDMITM, the HDMI logo and High-Definition Multimedia Interface are trademarks or registered trademarks of HDMI Licensing LLC."

-This DTV can receive the High-Definition Multimedia Interface(HDMI) or Input of Digital Visual Interface(DVI).

-This DTV supports HDCP(High-bandwidth Digital Contents Protection) Protocol for DTV(480p, 720p, 1080i) modes.

-When you Connect with HDMI/DVI Source Devices (DVD Player or Set Top Box or PC) supporting Auto HDMI/DVI function, automatically, support Plug & Play and then set the HDMI/DVI Source Devices(1280 x 720p). After reading in HDMI/DVI Source Devices using Display Data Channel(DDC) Protocol, EDID stored in DTV is used . If HDMI/DVI Source Devices not supported Auto HDMI/DVI is been, the Resolution is setted, manually.

- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p.

- To get the best picture quality, adjust the PC graphics card to 1024 x 768, 60Hz.

- When Source Devices have DVI Output Connector, you must connect audio with separated cable.(Refer to <How to connect>)

How to connect

1. When Source Devices(DVD Player or Set Top Box) support HDMI.

- If Source Devices have HDMI Output Connector, Source Devices connect to DTV with HDMI Cable .(not supplied with the product).

- If Source Devices support Auto HDMI, automatically, Source Devices divert output resolution in 1280x720p. But if not, resolution divert Manually Setting for reference Manual of Source Devices.

- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p.

- Because HDMI sends Digital Video and Audio with one cable, need not especial Audio Cable for using HDMI Cable.

2. When Source Devices(DVD Player or Set Top Box) supports DVI.

- If Source Devices have DVI Output Connector, Source Devices connect to DTV with HDMI to DVI Cable (not supplied with the product).

- If Source Devices support Auto DVI, automatically, Source Devices divert output resolution in 1280x720p. But if not, resolution divert Manually Setting for reference Manual of Source Devices.

- To get the best picture quality, adjust the DVD Player or Set Top Box output resolution to 1280 x 720p.

- In this case, Audio use other cable. When Source Devices have Fiber Optic Digital Audio Output Connector, Digital Audio DVI Input(DVI) of DTV connect to Fiber Optic Digital Audio Cable (not supplied with the product) or when Source Devices have Analog Audio Output Connector, RGB/DVI Audio Input of DTV connect to Audio Cable (not supplied with the product). And then you can listen to normal Audio.

3. When PC supports DVI.

- If PC have DVI Output Connector, Source Devices connect to DTV with HDMI to DVI Cable (not supplied with the product).

- To get the best picture quality, adjust the PC graphics card to 1024 x 768, 60Hz.

- Use the DTV’s HDMI/DVI(VIDEO) for video connections, depending on your PC connector.

- If the graphics card on the PC does not output analog RGB and DVI simultaneously, connect only one of either RGB Input or HDMI/DVI Input to display the PC on the DTV.

- If he graphics card on the PC does output analog RGB and DVI simultaneously, set the DTV to either RGB Input or HDMI/DVI Input;(the other mode is set to Plug and Play automatically by the DTV.)

- Then, make the corresponding audio connections. If using a sound card, adjust the PC sound as required.

- In this case, Audio use other cable. When PC (or sound card of PC) have Fiber Optic Digital Audio Output Connector, Digital Audio DVI Input(DVI) of DTV connect to Fiber Optic Digital Audio Cable (not supplied with the product) or when PC (or sound card of PC) have Analog Audio Output Connector, RGB/DVI Audio Input of DTV connect to Analog Audio Cable (not supplied with the product). And then you can listen to normal Audio.

20 Plasma TV

HDMI

Reference

Cable sample

HDMI Cable (not supplied with the product)

HDMI to DVI Cable (not supplied with the product)

Fiber Optic Digital Audio Cable (not supplied with the product)

Analog Audio Cable(RCA type) (not supplied with the product)

Analog Audio Cable(Stereo to RCA type) (not supplied with the product)

Owner’s Manual 21

HDMI

How to use

1. Connect the HDMI/DVI Source Devices(DVD Player or Set Top Box or PC) and the TV SET.

2. Turn on the display by pressing the POWER button on the TV SET and HDMI/DVI Source Devices remote control.

3. Select HDMI/DVI Input source in Main Input option of SETUP menu.(Refer to P.60)

4. Check the image on your TV SET. There may be noise associated with the resolution, vertical pattern, contrast or brightness in HDMI/DVI Source Devices. If noise is present, change the HDMI/DVI Source Devices to another resolution, change the refresh rate or adjust the brightness and contrast on the menu until the picture is clear. If the refresh rate of the PC graphics card can not changed, change the PC graphics card or consult the manufacturer of the PC graphics card.

Notes:

- Depending on the graphics card, DOS mode may not work if you use a HDMI to DVI Cable.

- Avoid keeping a fixed image on the TV SET screen for a long period of time. The fixed image may become permanently imprinted on the screen. Use the Orbiter screen saver when possible.

- When Source Devices connected HDMI/DVI Input, output PC Resolution(VGA, SVGA, XGA), Position, Size may not fit to Screen. As shown the lower picture, press the Adjust button to adjust the screen Position of TV SET and contact an PC graphics card service center.

- When Source Devices connected HDMI/DVI Input output TV SET Resolution(480p, 720p, 1080i), TV SET Display fit EIA/CEA861-B Specification to Screen. If not, refer to the Manual of HDMI/DVI Source Devices or contact your service center.

- In case HDMI/DVI Source Devices is not connected Cable or poor cable connection, "NO SIGNAL" OSD display in HDMI/DVI Input. And In case of, Video Resolution not supported TV SET output in HDMI/DVI Source Devices, "INVALID FORMAT" OSD display. Refer to the Manual of HDMI/DVI Source Devices or contact your service center.

POSITION G

SIZE

PHASE

RESET

Adjust

In This Mode, the Supported TV SET Resolution Specification

- 1920 x 1080 I @ 59.94Hz / 60Hz, 16:9

- 1280 x 720 P @ 59.94Hz / 60Hz, 16:9(preferred format)

- 704 x 480 P @ 59.94Hz / 60Hz, 16:9

- 704 x 480 P @ 59.94Hz / 60Hz, 4:3

In This Mode, the Supported PC Resolution Specification

- 640 x 480 @ 60Hz

- 640 x 480 @ 72Hz

- 640 x 480 @ 75Hz

- 800 x 600 @ 56Hz

- 800 x 600 @ 60Hz

- 800 x 600 @ 72Hz

- 800 x 600 @ 75Hz

- 1024 x 768 @ 60Hz(preferred format)

- 1024 x 768 @ 70Hz

- 1024 x 768 @ 75Hz

22 Plasma TV

Installation

TV Guide On Screen Setup

- The TV Guide On Screen system uses Setup information to provide you with show listings and lineups in your area—which are

updated several times a day.

- Once you set up the TV according to manufacturer’s instructions, you are ready to set up TV Guide On Screen.

Note: The TV Guide On Screen interactive program guide provides listings for cable-ready, cable box, and digital cable services

as well as over-the-air broadcast. It does not provide listings for satellite services.

AC INPUTAC INPUT

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

ANT IN

ANT OUT

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

CABLE

HDMI / DVI(VIDEO)

Cable

ANTENNA

How to connect VCR and Cable Box

1. Antenna Service

2. Cable Service without a Cable Box

AC INPUTAC INPUT

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

CABLE

HDMI / DVI(VIDEO)

Cable

ANTENNA

ANT IN

ANT OUT

VCR Rear

VCR Front

VCR Rear

VCR Front

Owner’s Manual 23

Installation

3. Cable Service with a Cable Box

AC INPUTAC INPUT

VCR

Cable

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

CABLE

Cable

ANTENNA

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

ANT IN

ANT OUT

4. Antenna and Cable Service without a Cable Box

5. Antenna and Cable Service with a Cable Box

AC INPUTAC INPUT

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

CABLE

Cable

ANTENNA

ANT IN

ANT OUT

AC INPUTAC INPUT

CABLE

Cable

ANTENNA

S-VIDEO

OUT

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

VCR

Cable

(R) AUDIO (L) VIDEO

OUTPUT SWITCH

ANT OUT

ANT IN

Cable Box Rear

VCR Rear

VCR Front

Cable Box Front

VCR Rear

VCR Front

Cable Box Rear

VCR Rear

VCR Front

Cable Box Front

24 Plasma TV

Installation

Note:

• The G-LINK cable is necessary for the TV Guide On Screen system to work with your Cable Box and VCR. See Page 22~23 for G-LINK connection instructions.

1.Reminder Screen

The TV Guide On Screen system's Reminder Screen appears:

-- after initial TV set up

-- if you power Off the TV and then power it back On

To make a selection, use the

D/ E

button to highlight to an option,

and press ENTER.

• "Set up TV Guide On Screen now,” displays the Welcome Screen. Press ENTER to begin Setup.

• ”Remind me to set up later" returns you to watching TV.

• ”Don't remind me again" returns you to watching TV and stops the

reminder screen from appearing upon power On.

How to use

1. Screen 1: Country

•This screen asks you the location of your TV.

•Use the

D/ E

button to highlight a country.

•Press ENTER to display Screen 2.

2.Welcome Screen

The TV Guide On Screen system's Welcome Screen appears:

-- by pressing the TV Guide key

-- when you power On your TV if you previously skipped "Set up TV Guide On Screen now" on the Reminder Screen.

The Welcome Screen highlights features of the TV Guide On Screen

system.

Press ENTER to begin Setup.

Owner’s Manual 25

Installation

2. Screen 2: Enter Zip or Postal Code

Option 1

•If you selected USA in Screen 1, you see the ZIP Code screen.

•You input numbers by either pressing the number keys on the remote

or using the

D/ E

button to display a number, and then the F / G but-

ton to move to another field.

•Press ENTER to display Screen 3.

Option 2

•If you selected Canada in Screen 1, you see the Postal Code screen.

•You input characters by using the

D/ E

button, and then the F / G but-

ton to move to another field.

•Press ENTER to display Screen 3.

3. Screen 3: Do you have Cable?

•If you select Yes, you see Screen 4.

•If you select No, you see Screen 12.

4. Screen 4: Do you have a Cable Box?

•If you select Yes, you see Screen 5.

•If you select No, you see Screen 12.

26 Plasma TV

Installation

6. Screen 6: Cable Box Tuning Channel

•Select the channel used for the cable box.

•Press ENTER to display Screen 7.

7. Screen 7: Cable Box Configuration Diagram

•The diagram shows the correct way to install the G-LINK Cable from the back of the device to the cable box.

Make sure the G-LINK Cable is properly installed.

•Press ENTER to display Screen 8.

5. Screen 5: Which TV input is the cable box plugged into?

•If you select Cable, you see Screen 6.

•If you make any other choice, you see Screen 7 .

Owner’s Manual 27

Installation

8. Screen 8: Cable Box Brand Name

•Use the

D/ E

button to select a cable box brand.

•Press ENTER to display Screen 9.

9. Screen 9: Cable Box Preparation

Follow the on-screen instructions, and press ENTER to display

Screen 10.

10. Screen 10: Cable Box Code Testing

When testing is done, Screen 11 displays automatically.

11. Screen 11: Cable Box Tuned to Channel 9?

If you select Yes, you see Screen 12.

If you select No, a different code is tested in Screen 10.

Note:

•Many Cable Boxes require testing more than one code.

If you select Test this code again, the same code is tested again in Screen 10.

28 Plasma TV

Installation

14. Screen 14: Congratulations

•Press ENTER to display Screen 15.

13. Screen 13: Are your basic settings correct?

•If you select Yes, you see Screen 14.

•If you select No, you see Screen 1.

12. Screen 12: Do you have an antenna connected?

•If you select Yes, you see Screen 13.

Note:

•If you selected No in Screen 3 then you must select Yes in this screen to receive a channel lineup and listings.

•If you select No, you see Screen 13.

Owner’s Manual 29

Installation

17. Screen 17: VCR Brand Name

•Use the

D/ E

button to select the brand of the recording device.

•Press ENTER, and you see Screen 18.

16. Screen 16: VCR Configuration Diagram

•This screen shows the correct way to install the G-LINK Cable from

the back of the TV to the Recording device.

Make sure the G-LINK Cable is properly installed.

•Press ENTER, and you see Screen 17.

15. Screen 15: Is a VCR Connected?

•If you select Yes, you see Screen 16.

•If you select No, you see Screen 21.

30 Plasma TV

Installation

18. Screen 18: VCR Preparation

Follow the on-screen instructions, and press ENTER to display Screen

19.

19. Screen 19: VCR Code Testing

When testing is done, Screen 20 displays automatically.

20. Screen 20: VCR Tuned to Channel 9?

•If you select Yes, you see Screen 21.

•If you select No, a different code is tested in Screen 19.

Note : Many VCRs require testing more than one code.

•If you select Test this code again, the same code is tested again in Screen 19.

Owner’s Manual 31

Installation

21. Screen 21: Confirming Your Settings

Verify the Setup information is correct.

If it is, select Yes, end setup, and you see Screen 22.

If it is not, select No, repeat setup process, and you see Screen 1.

22. Screen 22: Congratulations

•You have successfully completed Setup!

•Press ENTER and you see Screen 23.

23. Screen 23: Helpful Information

•This screen tells you valuable information on using your Guide.

•Press ENTER to watch TV.

Notes:

The TV Guide On Screen system receives program listings data through your cable or over-the-air video signal. In order to

receive regular program listings, please remember to do the following:

1. Turn OFF your TV when it is not in use. (Do not unplug the power cord.)

2. If you have a Cable box connected, leave it ON.

3. If you have a VCR connected, turn it OFF when not in use. (Do not unplug the power cord.)

4. If you have more than one Cable system in your area, you may be prompted to select which Cable system’s program data to download. If so prompted, please follow the on-screen instructions.

32 Plasma TV

IEEE 1394

- It's available to communicate to either direction and you can give and take a image, sound, or each control command with one cable.

- Only use the DVHS and MicroMV Camcorder to work the 1394.

How to connect the 1394

•

To work the 1394, this 3 methods can used.

1. When connecting the DVHS or the MicroMV Camcorder, as shown in the (a) or (b) figure, press the 1394 button to show the

control panel.

TV/VIDEO

VOL CH

POWER

TV GUIDE

(a) TV DVHS

TV/VIDEO

VOL CH

POWER

TV GUIDE

(b) TV MicroMV Camcorder

<TV>

<DVHS>

2. When connecting the DVHS and the MicroMV Camcorder, as shown in the (c) figure, press the 1394 button to show the con-

tents panel and then select the DVHS or the MicroMV Camcorder to show the control panel.

TV/VIDEO

VOL CH

POWER

TV GUIDE

<TV>

<DVHS>

When connecting the 1394 and then playing, you must use the original DVHS tape. If not, it may be occurred the errors.

IEEE 1394 Functions

Owner’s Manual 33

IEEE 1394

IEEE 1394 functions continued

DVHS

VHow to play the DVHS

TV/VIDEO

VOL CH

POWER

TV GUIDE

<TV>

<DVHS>

1. Connect the IEEE 1394 jack of the TV to the IEEE 1394 jack of the DVHS with IEEE 1394 Cable.

2. When watching the TV, press the 1394 button.

• Show the control panel of DVHS.

POWER

GGFF

Panasonic

NV-DH2

DVHS

STOP+0:00:06

* Supported DVHS List

VICTOR(HM-DH35000U)

JVC(HM-DH30000U)

JVC(HM-DH40000U)

MITSUBISHI(HS-

HD1100U)

MITSUBISHI(HS-

HD2000U)

Hitachi(DT-DR20000)

Hitachi(DT-DRX100)

PANASONIC(NV-DH1)

PANASONIC(NV-DH2)

PANASONIC(NV-DHE20)

TOSHIBA(A-HD2000)

• The control panel of DVHS

-Depending on the connected equipment, marked control panel may differ.

POWER

GGFF

Panasonic

NV-DH2

DVHS

STOP

0:00:06

1 2

6 7

3 4

0:00

1. DVHS Company

2. DVHS Model

3. Connected Equipment to the 1394

4. DVHS Operating Status

5. Power On/Off

6. Tape Status

• Tape shape Icon - Tape in or not

• Lock shape Icon - Use or not use

7. DVHS Play Time

8. Initializing Play Time

9. DVHS Play, Pause, Stop, Search or Skip

(Notes:

• Skip- This function is for a fast search.

It searches the program’s start

point and then plays.

On skipping, Search (

GG, FF

), Pause

( ) and Play (

) are displayed on

the Control Panel.

In some models, it’s not available to

operate the Skipping (

FF, GG

)

function.

34 Plasma TV

IEEE 1394

IEEE 1394 functions continued

How to play the MicroMV Camcorder

MicroMV Camcorder

TV/VIDEO

VOL CH

POWER

TV GUIDE

<TV>

1. Connect the IEEE 1394 jack of the TV to the IEEE 1394 jack of the MicroMV Camcorder with IEEE 1394 Cable.

2. When watching the TV, press the 1394 button.

• Show the control panel of MicroMV Camcorder.

• The control panel of MicroMV Camcorder

-Depending on the connected equipment, marked control panel may differ.

1. MicroMV Camcorder Company

2. MicroMV Camcorder Model

3. Connected Equipment to the 1394

4. MicroMV Camcorder Operating Status

5. Tape Status

• Tape shape Icon - Tape in or not

• Lock shape Icon - Use or not use

6. MicroMV Camcorder Play Time

7. MicroMV Camcorder Play, Search or Stop

8. Initializing Play Time

* Supported MicroMV Camcorder List

SONY MICORMV IP-5

SONY MICORMV IP-45

SONY MICORMV IP-210

SONY MICORMV IP-7

SONY MICORMV IP-55

SONY MICORMV IP-220

GGFF

Sony

DCR-IP45

CAM

STOP+0:00:06

0:00

GGFF

Sony

DCR-IP45

CAM

STOP

0:00:06

0:00

1 2

5 6

3 4

Owner’s Manual 35

IEEE 1394

IEEE 1394 functions continued

How to play the MicroMV Camcorder and DVHS

MicroMV Camcorder and DVHS

1. Synchronously, connect the IEEE 1394 jack of the TV to the IEEE 1394 jack of the DVHS and the MicroMV Camcorder with IEEE 1394 Cable.

PVR O

PVR V

GGFF

Sony

DCR-IP45

CAM

STOP+0:00:06

0:00

• The playing screen is stored in the PVR or DVR.

2. Press the

D / E

/ F / G button to move into the PVR V, then press ENTER button to store it . And then

this program is ended.

PVR O

PVR V

GGFF

Sony

DCR-IP45

CAM

STOP+0:00:06

0:00

36 Plasma TV

IEEE 1394

IEEE 1394 functions continued

How to connect the 1394

• When connecting these 3 methods, the 1394 will not work properly.

TV/VIDEO

VOL CH

POWER

TV GUIDE

(a) LOOP Connection

<TV>

<DVHS>

TV/VIDEO

VOL CH

POWER

TV GUIDE

(b) Daisy Chain

<TV>

<DVHS>

<Connect

the IEEE1394 Cable>

TV/VIDEO

VOL CH

POWER

TV GUIDE

<TV>

<DVHS>

<Connect

the IEEE1394 Cable>

Owner’s Manual 37

TV Guide On Screen System

TV Guide On Screen

System

Overview

- Your new TV contains the TV Guide On Screen Interactive Program Guide.

The TV Guide On Screen system has features that help you get the most out of your viewing experience.

TV Guide On Screen Overview

The TV Guide On Screen system has the following features:

•Eight days of show listings (today plus seven days).

•Icons that indicate show rating, stereo, HDTV, new episode, etc.

•Intuitive up/down/left/right navigation using your remote control.

•Set shows to Record.

•Schedule show Reminders.

•Search shows by category (e.g., Movies, Sports, Children, etc.).

•Search for shows based on keywords or alphabetically by title.

•Direct tuning to a channel.

•Show information while watching TV.

•Streamlined System Setup and default setting options.

•Channel lineup customization.

•Help screens while in the Guide.

38 Plasma TV

TV Guide On Screen System

Screen Components

TV Guide On Screen

System continued

- The screens displayed in the TV Guide On Screen system share many of the same compo-

nents, as shown in the following figure:

•Video Window - displays TV video while the Guide is displayed

•Service Bar - provides access to the 4 main Guide Services

•Current Service Label - indented to indicate current Service displayed

•Tile - displays show title

•Highlight - indicates an active tile

•Info Box - provides information for a highlighted item

•Info Button - cycles through the various Info Box sizes

•Channel Logo - identifies network

•Record/Remind Icons - indicates a show is set to Record or set as a Reminder

•Panel Ad - location where show- or product-specific information appears (and also where Panel Menu appears)

Owner’s Manual 39

TV Guide On Screen System

TV Guide On Screen

System continued

•A Panel Menu appears when the Menu key is pressed on a highlighted tile and additional options are available. It also

appears when you press ENTER on a show starting in the future.

•When a Panel Menu appears, the highlighted tile changes color to indicate the Panel Menu relates to this tile.

•The Panel Menu displays below the Video Window.

•Help is available for a displayed Panel Menu by pressing the INFO button.

•The

D / E

button move between the options within the Panel Menu.

•The left and right arrows move to adjacent options unless the highlight is on an odometer, where these arrows change the

odometer choice.

•Pressing ENTER from an odometer or number entry box moves the highlight to the default command button of that Panel

Menu, for example, Schedule Reminder.

•Pressing ENTER from a highlighted command button executes the action and closes the Panel Menu (e.g., Schedule

Reminder, Cancel).

•Select Cancel to cancel any changes and press ENTER to close this menu.

•Pressing Menu is a shortcut to Cancel. Press Menu to cancel any changes and close the menu.

•If a Panel Menu contains more menu options than can be displayed on a single screen,

D / E

button appear at the top or

bottom of a menu. Simply scroll down to access these options.

• Panel Menu

40 Plasma TV

TV Guide On Screen System

TV Guide On Screen

System continued

- Access Listings by pressing the TV Guide button on your remote or on the front panel of your TV.

- Listings is always the first Service displayed in the Guide.

- With Listings highlighted, press the Info button to display a Help screen. Press the Info button again to close the screen.

•View 8 days of show listings

•Read show descriptions

•Tune directly to a show currently airing

•Set a show to Remind

•Set a show to Record

•Lock and unlock the Video Window

•Access Panel and Channel Ads

Use the

D / E

/ F / G buttons to move the highlight

within Listings to:

Main Services

V < Listings >

Notes: There may be times when the TV Guide On

Screen system could display partial or no program list-

ings. The reasons for this include:

• Program schedule information was not provided to TV

Guide On Screen.

• The transmission of the program listings was inter-

rupted.

The phrase “No Listings” will be replaced with program

information during the next transmission, which should

occur within the next 24 hours.

Please remember to turn off your TV when not in use

in order to receive program listings.

Owner’s Manual 41

TV Guide On Screen System

- Search lets you find shows by category (Alphabetical, Movies, Sports, Children, Educational, News, Variety, Series, HDTV) or by

Keyword.

- With Search highlighted, press the Info button to display a Help screen.

Press the Info button again to close the screen.

•Category Search Example: Movies

1. From Search, use the Ebutton to highlight Movies.

V < Search >

TV Guide On Screen

System continued

42 Plasma TV

TV Guide On Screen System

2. Use the Ebutton to highlight a subcategory (for example, All).

TV Guide On Screen

System continued

3. Press ENTER to display a list of all Movies, organized by date

and time.

You can choose to set a recording, a reminder, or tune to the channel.

4. Highlight a show and press ENTER to watch (if on now) or

the Menu key to display the Episode Options menu.

Go to Service Bar - closes the menu, changes no infor-

mation, and returns to the Search Service Bar.

Tune to Channel - exits the Guide and tunes to the chan-

nel of the highlighted show (show airs in the future).

Note: This option reads Watch Now if the show is cur-

rently airing.

Set Recording - displays the Record Options menu, from

which you can set frequency, start and end time, etc.

Set Reminder - displays the Remind Options menu, from

which you can set frequency, when, automatically power

On, and auto-tune the TV.

Cancel - closes the menu, changes no information, and

returns to the highlighted show.

Owner’s Manual 43

TV Guide On Screen System

TV Guide On Screen

System continued

- Keyword search lets you enter a word(s) to look for a particular show by category or for every show title that matches.

•Keyword Search

1. Highlight the Keyword navigation label, and press

ENTER button to display the Keyword Search menu.

2. Highlight New Search, and press ENTER button.

3. The Search Options menu is displayed.

4. Highlight Category, and use the

F / G button to select

a category to search (e.g. All, HDTV, Children, Sports,

etc.). When finished, use the Ebutton to highlight

Enter Keyword.

5. Highlight Enter Keyword, and press ENTER.

Then the keyboard is displayed.

6. Use the

D / E

/ F / G button to highlight a character,

and press ENTER to display it. When complete, high-

light Done and press ENTER.

44 Plasma TV

TV Guide On Screen System

The Guide stores all the keywords you create. To edit or

delete a keyword, highlight the keyword and press the

Menu key. A Search Options menu is displayed.

Go to Service Bar - closes the menu, changes no infor-

mation, and returns to the Search Service Bar.

Edit Search- displays the keyboard, where you can

change the keyword.

Delete Search- A Confirm menu is displayed.

•Yes - deletes the Search

•No - closes the panel menu

Cancel - closes the menu, changes no information, and

returns to the highlighted show.

7. A list of all matching shows for that keyword is dis-

played.

Like the Category Search Example, you can highlight

a show, and press ENTER to display all airings. You

can then highlight a specific listing and press ENTER

to watch (if On now) or the Menu key to display the

Episode Options menu.

From the Episode Options menu, choose to set a

recording, a reminder, or tune to the channel, as pre-

viously described.

TV Guide On Screen

System continued

Owner’s Manual 45

TV Guide On Screen System

- Schedule lets you review, edit, or delete Record and Remind events that you set previously.

- With Schedule highlighted, press the Info button to display a Help screen. Press the Info button again to close the screen.

- An icon identifies the event type:

TV Guide On Screen

System continued

Highlight an event, and press the Menu key for options.

Go to Service Bar - closes the menu, changes no information, and returns to the Schedule Service Bar. Tune to channel - exits the Guide and tunes to the highlighted show. Delete Recording - removes the recording from the Schedule, after a Confirm screen. Edit Recording - opens a menu from which you can change existing recording information. Set Reminder - opens a menu from which you can set a Reminder for the show (Record is not cancelled). Cancel - closes the menu, changes no information, and returns to the highlighted show.

V < Schedule >

Record

W Once —records the show one time

W Regularly , Daily —records the show every time

the show airs on the same channel and starts at the same

time

W Weekly —records the show each time the show airs on

the same day of the week, on the same channel and starts at

the same time

W Off —keeps the show in the list but will not record this

show until the frequency is changed.

Remind

W Once —sets a show reminder one time

W Regularly , Daily —sets a show reminder

every time the show airs on the same channel and

starts at the same time

W Weekly —sets a show reminder each time the

show airs on the same day of the week, on the same

channel and starts at the same time

W Off —keeps the show in the list but will not remind

until the frequency is changed

46 Plasma TV

TV Guide On Screen System

TV Guide On Screen

System continued

- After you initially complete Guide Setup, you can make changes to Guide settings in the following areas:

• Change System Settings

• Change Channel Display

• Change Default Options

Highlight a choice, press ENTER, and follow the on-screen instruc-

tions.

• Change System Settings

This option appears after you have completed the initial Guide

Setup process.

Press ENTER to display the Confirming Your Settings screen. You

see your current settings.

Choose one of the options, press ENTER, and follow the on-screen

instructions.

V < Setup >

With Setup highlighted, press the Info button to display a Help

screen. Press the Info button again to close the screen.

Owner’s Manual 47

TV Guide On Screen System

Press ENTER to display the Channel Editor screen.

Then, highlight a channel and press Menu. A Grid Options

menu is displayed.

Highlight Go Back to Setup to close the menu, change no

information, and return to the Setup Service Bar.

Or make changes and when finished, press ENTER to high-

light Done. Press ENTER again to close the menu and

accept the changes.

Highlight Cancel to close the menu, change no information,

and return to the highlighted channel.

• Change Channel Display

Change Channel Display lets you edit channel information

that appears in Listings. With Change Channel Display you

can :

• Re-order the position or the channel appears in Listings

• Change the tune channel number

• Switch a channel

W On - the channel is always displayed

W Off - the channel is never displayed

W Auto-Hide - the channel is only displayed when

program information is available.

TV Guide On Screen

System continued

48 Plasma TV

TV Guide On Screen System

General Default Options lets you set defaults for the following:

•The initial Info Box size when the TV guide on screen system is

entered.

Choices are No, Small, Large, and Last Used

(Default = Last Used).

•The Info Box size rotation when the Info key is pressed while in

the TV guide on screen system.

Choices are No only, Small only, Large only, No & Small, No &

Large, Small & Large, All (Default = All)

•Automatic entry into the TV guide on screen system (Auto-Guide)

when the TV is powered On.

Choices are On and Off (Default = On).

Highlight General Default Options, and press the Menu key to dis-

play the General Default Options menu.

Highlight Go to Service Bar to close the menu, change no infor-

mation, and return to the Setup Service Bar.

When finished, press ENTER to highlight Done. Press ENTER

again to close the menu and accept the changes.

Highlight Cancel to close the menu, change no information, and

return to the highlighted option.

• Change Default Options

Change Default Options lets you change default settings in the

following categories:

•General Default Options

•Record Defaults

•Remind Defaults

Highlight Change Default Options, and press ENTER.

TV Guide On Screen

System continued

Owner’s Manual 49

TV Guide On Screen System

< Record Defaults>

Record Default Options lets you set defaults for the following:

• When to start the record event. Choices are 120 minutes early to

120 minutes late, to On time. (Default = On time)

• When to end the record event. Choices are 120 minutes early to

120 minutes late, to On time. (Default = On time)

• Recorder choice: Please choose the VCR only. This TV does not

provide other devices with a recording feature.

Highlight Record Defaults, and press the Menu key to display the

Record Default Options menu.

Highlight Go to Service Bar to close the menu, change no infor-

mation, and return to the Setup Service Bar.

TV Guide On Screen

System continued

< Remind Defaults>

Remind Default Options lets you set defaults for the following:

•Power On the TV, if Off, when a Reminder is scheduled. Choices

are Yes and No.

(Default = No)

•Automatically tune the TV to the channel (TV must be On), when

a Reminder is scheduled. Choices are Yes and No.

(Default = No)

•When to display the reminder screen. Choices are 30 seconds to

15 minutes early, to 30 seconds to 15 minutes late, to On time.

(Default = 1 min early)

Highlight Remind Defaults, and press the Menu key to display the

Remind Default Options menu.

Highlight Go to Service Bar to close the menu, change no infor-

mation, and return to the Setup Service Bar.

When finished, press ENTER to highlight Done. Press ENTER

again to close the menu and accept the changes.

Highlight Cancel to close the menu, change no information, and

return to the highlighted option.

50 Plasma TV

TV Guide On Screen System

W Once —records the show one time

W Regularly —records the show every time the show

airs on the same channel and starts at the same time

W Weekly —records the show each time the show

airs on the same day of the week, on the same channel

and starts at the same time

W Off (not cancel) —keeps the show in the list but

will not record this show until the frequency is changed

W Cancel (no icon displayed)—does not record

TV Guide On Screen

System continued

Record

And Remind Features

V < Record >

You can set a show to Record in Listings, Search, and

Schedule or change Record settings for a show in Schedule.

There are 3 ways to set a show to Record:

1) Using the Record Button on the Remote

• Press the Record button on the remote to record the show

Once with current default settings (Start and End recording

On Time). Each time you press the Record button, you

change the record frequency (but not the default settings)

among Once (default), Regularly, Daily, Weekly and then

Cancel.

Note: The proper Record icon appears on the show tile, as the

Record button is pressed.

2) From a Panel Menu

•Highlight a show, and press Menu to display the Episode

Options menu.

•Highlight Set Recording, and press ENTER to display the

Record Options menu.

•Highlight the Frequency option, and use the left and right

arrows to choose among Once, Regularly, Weekly, and Off,

as previously described.

• Recorder choice: Please choose the VCR only. This TV does

not provide other devices with a recording feature.

•Note: Video Window Lock is operated to on or off using PIP

button in Listings mode.

Owner’s Manual 51

When finished, press ENTER to highlight Schedule Recording.

Press ENTER again to close the menu. You see a Record icon for

the selected frequency next to the show title.

Highlight Cancel to close the menu, change no information, and

return to the highlighted show.

TV Guide On Screen

System continued

3) Manual Recording

•Highlight the Schedule Service label, and press Menu to display

the Schedule Options menu.

•Use the

D / E

/ F / G buttons to move through the options. Use

the number or Use the

D / E

/ F / G buttons to change the infor-

mation, as necessary.

•Highlight New Manual Recording and press ENTER to display the

Record Options menu.

•Current information (i.e., date, start and end times, channel,

input) is displayed.

• Recorder choice: Please choose the VCR only. This TV does

not provide other devices with a recording feature.

TV Guide On Screen System

52 Plasma TV

TV Guide On Screen System

TV Guide On Screen

System continued

Record Conflict

A conflict message appears for the following reasons:

• a show set to Record overlaps with any part of another show pre-

viously set to Record,

• a show set to Record overlaps with a show previously set to auto-

tune

Select one of these options:

W record anyway - this show will override an existing show

set to Record or auto-tune

W don't record this show - cancel the Recording

Before a recording begins, a notification screen appears

if you are using a Cable box and your TV is On. At that

time, you can choose to start or cancel recording. If the

TV is not On, the recording occurs as scheduled. If there

is no activity for 3 minutes, the notification screen auto-

matically closes and completes the highlighted item.

When finished, press ENTER to highlight Schedule

Recording.

Press ENTER again to close the menu. You see a

Record icon for the selected frequency next to the show

title.

Note: Manual recording is listed by channel number.

Highlight Cancel to close the menu, change no informa-

tion, and return to the highlighted show.

•Use the left and right arrows to choose between Once, Daily,

Weekly, and Off, as follows.

W Once —records the time, channel, input, recorder combi-

nation one time.

W Daily —records the time, channel, input, recorder combi-

nation Monday through Friday.

W Weekly —records the time, channel, input, recorder com-

bination once a week on this selected day of the week

W Off (not cancel) —keeps the time, channel, input, recorder

combination in the list without recording until the frequency is

changed.

Owner’s Manual 53

TV Guide On Screen System

TV Guide On Screen

System continued

V < Remind >

You can set a show Reminder in Listings, Search, and Schedule

or change Reminder settings for a show in Schedule.

There are 2 ways to set a show Reminder:

1) From a Panel Menu

• Highlight a show, and press Menu to display the Episode Options

menu.

• Highlight Set Reminder, and press ENTER to display the Remind

Options menu.

•Highlight the Frequency option, and use the left and right arrows

to choose between:

W Once —sets a show reminder one time

W Regularly —sets a show reminder every time the show

airs on the same channel and starts at the same time

W Weekly —sets a show reminder each time the show airs

on the same day of the week, on the same channel and starts

at the same time

W Off —keeps the show in the list but will not remind until

the frequency is changed

•Power On the TV, if Off, when a Reminder is scheduled. Choices

are Yes and No. (Default = No)

•Automatically tune the TV to the channel (TV must be On), when

a Reminder is scheduled. Choices are Yes and No. (Default =

No)

•When to display the reminder screen. Choices are 30 seconds to

15 minutes early, to 30 seconds to 15 minutes late, to On time.

(Default = 1 min early)

When finished, press ENTER to highlight Schedule Reminder.

Press ENTER again to close the menu. You see a Remind icon for

the selected frequency next to the show title.

Highlight Cancel to close the menu, change no information, and

return to the highlighted show.

54 Plasma TV

TV Guide On Screen System

TV Guide On Screen

System continued

2) Manual Reminder

•Highlight the Schedule Service label, and press the Menu key to

display the Schedule Options menu.

•Use the

D / E

/ F / G buttons to move through the options. Use the

number or

D / E

/ F / G buttons to change the information, as

necessary.

•Highlight New Manual Reminder and press the ENTER key to dis-

play the Remind Options menu.

•Current information (i.e., date, start and end times, channel, input,

frequency, etc.) is displayed.

•Highlight the Frequency option, and use the F / G buttons to

choose among Once, Daily, Weekly, and Off, as follows.

W Once —sets a show reminder for the time, channel, input,

recorder combination one time

W Daily —reminds for the time, channel, input, recorder com-

bination Monday through Friday

W Weekly —sets a show reminder for the time, channel, input,

recorder combination once a week on this selected day of the

week

W Off (not cancel) —keeps the time, channel, input, destina-

tion combination in the list without reminding until the frequency

is changed

•Power On the TV, if Off, when a Reminder is scheduled. Choices

are Yes and No (Default =No).

•Automatically tune the TV to the channel (TV must be On), when

a Reminder is scheduled. Choices are Yes and No (Default = No).

When finished, press ENTER to highlight Schedule Reminder.

Press ENTER again to close the menu. You see a Remind icon for

the selected frequency next to the show title.

Note: Manual reminder is listed by channel number.

Highlight Cancel to close the menu, change no information, and

return to the highlighted show.

Owner’s Manual 55

TV Guide On Screen System

Based on your option settings, a notification screen will

appear, if your TV is On at the reminder time. You can

then choose to hide the reminder, or highlight the show,

and press ENTER to tune to the show. If there is no activ-

ity for 3 minutes, the notification screen automatically

closes and completes the highlighted item (hide

reminders).

If you choose Hide Reminders, the window closes for the

show or shows, but does not affect other Reminders you

set.

Note: If more than 2 reminders are set for the same time,

arrows appear on the Reminder screen. Use the

D / E

buttons to view the shows.

Remind Conflict

A conflict message appears for the following reasons:

• a show set with an Auto-Tune Reminder has the same

start time as an existing Auto-Tune Reminder.

• If you are using a cable box, a show set with an Auto-

Tune Reminder overlaps with a Recording already

scheduled.

Select one of these options:

W auto-tune anyway - this show will override an exist-

ing show set to auto-tune

W proceed, no auto-tune - set the show as a Reminder

but do not auto-tune

W don't set this reminder - cancel the Reminder

TV Guide On Screen

System continued

56 Plasma TV

Installation

Operation

- Be sure to select the RGB-PC/RGB-DTV source before operation. (For RGB-DTV input source, Position and Reset are available.)

- In RGB-PC/DVI-PC input source, setting are available.

- You can manually adjust picture position and minimize image shaking for the PC input source.

1. Press the ADJUST button and then use

D / E

button to select POSITION, SIZE,

PHASE.

2. Press ENTER button and then use

D / E

/ F / G buttons to make appropriate

adjustments.

• The PHASE adjustment range is -16 ~ +16.

• The SIZE adjustment range is -30 ~ +30.

3. Press ENTER button.

•Note: In HDMI/DVI-PC mode, screen

PHASE is not available.

Adjustment for screen Position, Size, and Phase

Screen Setup for PC mode

1. Press the ADJUST button and then use

D / E

button to select the RESET option.

2. Press ENTER button and then use F / G button to select Ye s.

3. Press ENTER button

Initializing (Reset to original factory values)

- To initialize the adjusted values

POSITION G

SIZE

PHASE

RESET

Adjust

POSITION

SIZE

PHASE

RESET G

Adjust

Initialize Settings

Owner’s Manual 57

Operation

On-screen Menus Language Selection

- The menus can be shown on the screen in the selected language. First select your language.

1. Press the MENU button and then use

D/ E

button to select the OPTION menu.

2. Press the G button and then use

D/ E

button to select Language.

3. Press the G button and then use

D/ E

button to select your desired language.

From this point on, the on-screen menus will be shown in the selected language.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Aspect Ratio

Cinema

Caption

Caption/Text

Caption Option

Language G

Demo

ISM Method

Low Power

English

Español

Français

CABLE

TTurning the TV On

urning the TV On

1. First, connect power cord correctly. At this moment, the TV switches to standby mode.

In standby mode to turn TV on, press the power, TV/VIDEO, CH (

D/ E

) button on the TV or press

the POWER, TV/VIDEO, COMP/RGB/HDMI, CH (+

-), Number (0 ~ 9) button on the TV .

Notes:

• If you intend to be away on vacation, disconnect the power plug from the wall power outlet.

• After turning on the TV, it takes time to be initialized for the TV Guide On Screen System.

2. Select the viewing source by using TV/VIDEO, COMP/RGB/DVI button on the remote control.

This TV is programmed to remember which mode it was last set to, even if you turn the TV off.

3. When finished using the TV, press the POWER button on the remote control. The TV reverts to

standby mode.

58 Plasma TV

Operation

- Automatically finds all channels available through antenna or cable inputs, and stores them in memory on the channel list.

- Run EZ Scan again after any Antenna/Cable connection changes.

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the G button and then use

D / E

button to select EZ Scan.

3. Press the ENTER button to begin the channel search.

Allow EZ Scan to complete the channel search cycle for TV, DTV, CATV, and CADTV.

EZ Scan (Channel Search)

Setup Menu Options

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the G button and then use

D / E

button to select Manual Scan.

3. Press the G button and then use

D / E

button to select TV, DTV, CATV, and

CADTV.

4. Press the

G button and then use

D / E

button to select channel number you want

to add or delete.

5. Press the ENTER button to add or delete for the channel number.

6. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Manual Scan

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

CABLE

EZ Scan

Manual Scan G

Channel Edit

DTV Signal

Channel Label

Main Input

Sub Input

Aux. Label

Set ID

Select channel type and

RF-channel number.

Notes:

•This channel number is different from normal channel showed Channel Edit.

•When Cable Box connect to RF2,3,4 in TV Guide Setup, CATV, CADTV is not working in EZ Scan.

Owner’s Manual 59

- Create two different types of channel lists in memory: “Custom list” and “Surf" (Favorite) channel list” from the default channel list created from the EZ Scan channel search.

- A custom list can be created by toggling each channel on or off with ENTER button. Once a channel is highlighted, you will be able to see whether the channel is currently added or deleted by referring to the small window at the top-left corner of the screen. You can create your own Surf channel with all channels. Use the SURF button on the remote control when a channel is highlighted and then you can create your Surf channel.

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the G button and then use

D / E

button to select Channel Edit.

3. Press the G button. You will now see a screen filled with channel numbers and

a preview picture.

4. Use

D / E

/ F / G button to select a channel and then use the ENTER button to

add or delete it. Press SURF to add the channel to the Surf List.

5. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Channel Edit

- Shows how strong your DTV signal is and whether you need to adjust your antenna or digital cable input. The higher the signal strength, the less likely you are to experience picture degradation.

- DTV Signals: When input signals are DTV, CADTV, this function is available.

1. Press the SIGNAL button.

2. View the on-screen signal strength monitor to see the quality of the signal being received.

• You can also check the

DTV Signal strength with the SETUP menu.

DTV Signal Strength

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

CABLE

EZ Scan

Manual Scan

Channel Edit G

DTV Signal

Channel Label

Main Input

Sub Input

Aux. Label

Set ID

Selection ( Gor ) leads you

to the channel edit screen.

Note:

•When Cable Box connect to RF2,3,4 in TV Guide Setup, CATV, CADTV is not working in EZ Scan.

60 Plasma TV

Operation

Setup Menu Options continued

- Changes the picture source so you can watch your off-air TV, cable TV, VCR, DVD, or any other devices that are connected to your TV.

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the G button and then use

D / E

button to select Main Input.

3. Press the G button and then use

D / E

button to select the source: Antenna, Cable, Video, Front Video, Component1, Component2, RGB-DTV (or RGB-PC), HDMI/DVI.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Main Picture Source Selection

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

EZ Scan

Manual Scan

Channel Edit

DTV Signal

Channel Label

Main Input G

Sub Input

Aux. Label

Set ID

Antenna

Cable

Video

Front Video

Component1

Component2

RGB-DTV

HDMI/DVI

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the

G button and then use

D / E

button to select Aux. Label.

3. Press the

G button and then use

D / E

button to select the source: Video, Front

Video, Component1, Component2, RGB, HDMI/DVI.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Aux. Label

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

EZ Scan

Manual Scan

Channel Edit

DTV Signal

Channel Label

Main Input

Sub Input

Aux. Label G

Set ID

Video Cable Box

Front Video VCR

Component1 DVD

Component2 Set Top Box

RGB PC

HDMI/DVI Game

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

EZ Scan

Manual Scan

Channel Edit

DTV Signal

Channel Label G

Main Input

Sub Input

Aux. Label

Set ID

Selection ( Gor ) leads you

to the channel logo screen.

- Choose preset labels for your channels.

- If a channel label is provided on the signal from the broadcasting station, the TV displays a short name for a channel even if you didn't preset a label for the channel.

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the G button and then use

D / E

button to select Channel Label.

3. Press the

G button. You will now see a screen filled with Labels and a preview screen.

4. Use the CH +/- button to select a channel to Label.

5. Use

D / E

/ F / G button to select the appropriate label for the channel, then press ENTER button to set the Label to

the selected channel.

- If you press button, you will see the channel banner. • For example:

Channel Label Setup

CABLE

CADTV

27-1

CNN

DOLBY DIGITAL

Owner’s Manual 61

Operation

- Adjust the picture appearance to suit your preference and viewing situations.

1. Press the MENU button and then use

D / E

button to select the VIDEO menu.

2. Press the G button and then use

D / E

button to select the desired picture option

(

Contrast, Brightness, Color, Sharpness, or Tint ).

3. Press the G button and then use F / G button to make appropriate adjustments.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

1. Press the VIDEO button repeatedly to select the picture appearance setup option as shown below:

Off (your own settings), Daylight, Normal, Night Time, Movie, Video Game, and Sports.

• You can also use the VIDEO menu to adjust EZ Picture.

2. Press the EXIT button to save and return to TV viewing.

EZ Picture

Manual Picture Control (

Manual Picture Control (Off

option)

- Choose one of three automatic color adjustments. Set to warm to enhance hotter colors such as red, or set to cool to see less intense colors with more blue.

1. Press the MENU button and then use

D / E

button to select the VIDEO menu.

2. Press the

G button and then use

D / E

button to select Color Temperature .

3. Press the G button and then use

D / E

button to select either Cool, Medium or

Warm.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Color

Color TT

emperature Control

- EZ Picture adjusts the TV for the best picture appearance. Select the preset value in the EZ Picture menu based on the program category.

- When adjusting Video menu options (contrast, brightness, color, sharpness, tint, and color temperature) manually, EZ Picture automatically changes to Off.

Daylight, Normal, Night Time, Movie, Video Game, and Sports settings are preset for optimum picture quality at

the factory and are not adjustable.

VVideo Menu Options

ideo Menu Options

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

EZ Picture

Contrast

Brightness

Color

Sharpness

Tint

Color Temperature G

Video Preset

Cool

Medium

Warm

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

EZ Picture

Contrast 85 G

Brightness 50

Color 50

Sharpness 50

Tint 0

Color Temperature

Video Preset

R G

CABLE

62 Plasma TV

Operation

- Use to quickly reset all the Video menu options to their original factory preset values.

1. Press the MENU button and then use

D / E

button to select the VIDEO menu.

2. Press the G button and then use

D / E

button to select Video Preset .

3. Press the G button to reset the Video menu options to original values.

VVideo Preset

ideo Preset

SETUP

VIDEO

AUDIO

TIME

OPTION

EZ Picture

Contrast

Brightness

Color

Sharpness

Tint

Color Temperature

Video Preset G

Selection ( Gor ) presets

the video configuration.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

EZ Picture

Contrast

Brightness

Color

Sharpness

Tint

Color Temperature

Video Preset

Off

- XD is LG Electronic’s unique picture improving technology to display a real HD

source through an advanced digital signal processing algorithm.

- When selecting EZ Picture options (Daylight, Normal, Night Time, Movie, Video

Game, and Sports), XD is automatically change to On.

1. Press the MENU button and then use

D / E

button to select the PICTURE menu.

2. Press the G button and then use

D / E

button to select XD.

3. Press the G button and then use

D / E

button to set On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

LOCK

CABLE

Owner’s Manual 63

Operation

- Other languages may be available if a digital signal is provided by the broadcasting station.

Audio Menu Options

1. Press the SOUND button repeatedly to select the appropriate sound setup as shown below:

Off (your own settings), Normal, Stadium, Theater, and Music.

• You can also adjust EZ Sound in the AUDIO menu.

2. Press EXIT button to save and return to TV viewing.

EZ Sound

Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the

G button and then use

D / E

button to select the desired sound option

(Balance, Treble, or Bass).

3. Press the

G button and then use F / G button to make appropriate adjustments.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Manual Sound Control (

Manual Sound Control (Off

option)

1. Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the G button and then use

D / E

button to select Audio Language.

3. Press the G button and then use

D / E

button to select: English, Spanish, or

French.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Audio Language

- EZ Sound lets you enjoy the best sound without any special adjustment because the TV sets the appropriate sound options based on the program content.

- When adjusting sound options (treble, bass, and front surround) manually, EZ Sound automatically switches Off.

- Normal, Stadium, Theater, and Music are preset for good sound quality at the factory and are not adjustable.

- Scans for changes in sound level during commercials, then adjusts the sound to match the specified audio level. SoundRite makes sure that the volume level remains consistent whether you are watching a commercial or a regular TV program.

1. Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the G button and then use

D / E

button to select EZ SoundRite.

3. Press the

G button and then use

D / E

button to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

EZ SoundRite

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Audio Language G

EZ SoundRite

EZ Sound

Balance

Treble

Bass

Front Surround

TV Speaker

English

Spanish

French

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Audio Language

EZ SoundRite G

EZ Sound

Balance

Treble

Bass

Front Surround

TV Speaker

Off

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Audio Language

EZ SoundRite

EZ Sound

Balance 0 G

Treble 50

Bass 50

Front Surround

TV Speaker

L R

- Adjust the sound to suit your taste and room situations.

CABLE

64 Plasma TV

Operation

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Audio Language

EZ SoundRite

EZ Sound

Balance

Treble

Bass

Front Surround G

TV Speaker

Off

3D EchoSound System

SRS TruSurround XT

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Audio Language

EZ SoundRite

EZ Sound

Balance

Treble

Bass

Front Surround

TV Speaker G

Off

Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the

G button and then use

D / E

button to select Front Surround.

3. Press the G button and then use

D / E

button to select Off, 3D EchoSound

System

or SRS (Sound Retrieval System) TruSurround XT..

• 3D EchoSound System

Creates a stunning simulated stereo effects from any mono sound and a realistic three-dimensional sound with a very wide and deep sound stage into stereo sound.

• SRS TruSurround XT

Takes advantage of any multi-channel format without needing to add extra speakers or equipment. Dialog clarity, bass enrichment, and the addition of stereo audio enhancement that produces an immersive sound experience from standard stereo material.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Front Surround

Press the MENU button and then use

D / E

button to select the AUDIO menu.

2. Press the G button and then use

D / E

button to select TV Speaker.

3. Press the G button and then use

D / E

button to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

TV Speakers On/Of

f Setup

- Turn TV speakers off if using external audio equipment. Feature turns the TV Speakers option On or Off.

1. Use the SAP button to select your desired MTS mode in analog signal. Each time you press the SAP button, Mono,

Stereo, or SAP appear in turn.

• If other languages available on the digital signal, select them with the SAP button.

2. Press EXIT button to save and return to TV viewing.

Stereo/SAP

Broadcasts Setup

- This TV can receive MTS stereo programs and any SAP (Secondary Audio Program) that accompanies the stereo program; if

the station transmits an additional sound signal as well as the original one.

- When having selected Stereo or SAP button on the remote control, this TV can only receive the signal in case that the TV sta-

tion transmits the proper signals.

- Mono sound is automatically received if the broadcast is only in Mono; even though Stereo or SAP has been selected.

- Select Mono if you want to listen to the mono sound in remote fringe areas during stereo/SAP broadcasting.

- Stereo or SAP can be received in Analog channel.

- is a trademark of SRS Labs, Inc.

- TruSurround XT technology is incorporated under license from SRS Labs, Inc.

- Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

CABLE

Owner’s Manual 65

Operation

TTime Menu Options

ime Menu Options

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Auto Clock G

Manual Clock

Off Timer

On Timer

Sleep Timer

Auto Off

Off

Time Zone Eastern

Daylight Auto

Saving

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Auto Clock

Manual Clock

Off Timer

On Timer

Sleep Timer

Auto Off

Off

Time 6 : 30 AM

Ch. TV 2-0

Vol 17

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Auto Clock

Manual Clock G

Off Timer

On Timer

Sleep Timer

Auto Off

Year - - - -

Date - - / - -

Time - - : - - - -

- Timer function operates only if current time has been set.

- Off-Timer function overrides On-Timer function if they are set both set to the same time.

- The TV must be in standby mode for the On-Timer to work.

- If you do not press any button within 2 hours after the TV turns on with the On Timer function, the TV will automatically revert to standby mode.

On/Of

On/Off f TT

imer Setup

1. Press the MENU button and then use

D / E

button to select the TIME menu.

2. Press the G button and then use

D / E

button to select Off Timer or On Timer.

3. Press the G button and then use

D / E

button to select On.

• To cancel

On/Off timer function, select Off.

4. Press the

G button and then use

D / E

button to set the hour.

5. Press the

G button and then use

D / E

button to set the minutes.

6. For only On timer function

Press the

G button and then use

D / E

button to select the channel at turn-on.

Press the

G button and then use

D / E

button to set the sound level at turn-on.

7. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Auto Clock Setup

- The time is set automatically from a digital channel signal.

- The digital channel signal includes information for the current time provided by the broadcasting station.

- Set the clock manually, if the current time is set incorrectly by the auto clock function.

- When you set up TV Guide, Auto Clock menu is not selected.

1. Press the MENU button and then use

D / E

button to select the TIME menu.

2. Press the G button and then use

D / E

button to select Auto Clock.

3. Press the

G button and then use

D / E

button to select On.

4. Press the G button and then use

D / E

button to select your viewing area time

zone:

Eastern, Central, Mountain, Pacific, Alaska, or Hawaii.

5. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

Manual Clock Setup

- If current time setting is wrong, reset the clock manually.

- When you set up TV Guide, Manual Clock menu is not worked.

1. Press the MENU button and then use

D / E

button to select the TIME menu.

2. Press the

G button and then use

D / E

button to select Manual Clock.

3. Press the G button and then use F / G button to select either the year, date, or

time option. Once selected, use the

D / E

button to set the year, date, and time

options.

4. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

CABLE

66 Plasma TV

Operation

Auto Of

Auto Offf

- If set to on and there is no input signal, the TV turns off automatically after 10 minutes.

1. Press the MENU button and then use

D / E

button to select the TIME menu.

2. Press the

G button and then use

D / E

button to select Auto Off.

3. Press the G button and then use

D / E

button to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Sleep

Sleep TT

imer

- The Sleep Timer turns the TV off at the preset time. Note that this setting is cleared when the TV is turned off.

- You can also set up the

Sleep Timer in the TIME menu.

1. Press the TIMER button repeatedly to select the number of minutes. First the

Off option appears on the screen,

followed by the following sleep timer options: 10, 20, 30, 60, 90, 120, 180, and 240 minutes.

2. When the number of minutes you want is displayed on the screen, press the ENTER button. The timer begins to

count down from the number of minutes selected.

3. To check the remaining minutes before the TV turns off, press the TIMER button once.

4. To cancel the Sleep Timer, press the TIMER button repeatedly to select

Off.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Auto Clock

Manual Clock

Off Timer

On Timer

Sleep Timer

Auto Off G

Off

CABLE

Owner’s Manual 67

Operation

Owner’s Manual 67

Option Menu Features

Aspect Ratio Control

- Lets you choose the way an analog picture with a 4:3 aspect ratio is displayed on your TV with a 16:9 ratio picture format. When you receive an analog picture with a 4:3 aspect ratio on your 16:9 TV, you need to specify how the picture is to be displayed.

- If you are viewing a picture with a 16:9 aspect ratio, you can’t use the Horizon aspect ratio option.

- Horizon aspect ratio is not available for Component 1-2 (720p/1080i)/RGB-DTV (720p/1080i)/HDMI/DVI-DTV (720p/1080i)/DTV(720p/1080i) input source.

- RGB-PC/DVI-PC input source use 4:3 or 16:9 aspect ratio.

- Note: If a fixed image is displayed on the screen for a long time, that fixed image may become imprinted on the screen and

remain visible.

•

Set By Program

Selects the proper picture proportion to match the source’s image. (4:3 → 4:3, 16:9 → 16:9)

• 4:3

Choose 4:3 when you want to view a picture with an original 4:3 aspect ratio, with black bars appearing at both the left and right sides.

• 16:9

Choose 16:9 when you want to adjust the picture horizontally, in a linear proportion to fill the entire screen.

• Horizon

Choose Horizon when you want to adjust the picture in a non-linear proportion, that is, more enlarged at both sides, to create a spectacular view.

• Zoom 1

Choose Zoom 1 when you want to view the picture without any alteration. However, the top and bottom portions of the picture will be cropped.

• Zoom 2

Choose Zoom 2 when you want the picture to be altered, both vertically extended and cropped. The picture taking a halfway trade off between alteration and screen coverage.

• Cinema Zoom

Choose Cinema Zoom when you want to enlarge the picture in correct proportion. Note: When enlarging or reducing the picture, the image may become distorted. You can adjust the enlarge proportion of Cinema Zoom using

D / E

button. The adjustment range is 1~16.

1. Press the RATIO button repeatedly to select the desired picture format.

You can also adjust Aspect Ratio in the OPTION menu.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Aspect Ratio

Cinema G

Caption

Caption / Text

Caption Option

Language

Demo

ISM Method

Low Power

CABLE

Cinema Mode Setup

- Set up the TV for the best picture appearance for viewing movies.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

G button and then use

D / E

button to select Cinema.

3. Press the

button and then use

D / E

button to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Off

68 Plasma TV

Operation

Caption/T

ext

Analog Broadcasting System Captions

- Select a caption mode for displaying captioning information if provided on a program.

- Analog caption displays information at any position on the screen usually the program's dialog.

- Text displays information, usually at the bottom position and is used for a data service, generally not program related.

- Caption/Text, if provided by the broadcaster, would be available for both digital and analog channels on the Antenna/Cable.

- This TV is programmed to remember the caption/text mode it was last set to, when you turn the power off.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Aspect Ratio

Cinema

Caption

Caption / Text G

Caption Option

Language

Demo

ISM Method

Low Power

CC 1

CC 2

CC 3

CC 4

Tex t 1

Tex t 2

Tex t 3

Tex t 4

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Aspect Ratio

Cinema

Caption

Caption / Text G

Caption Option

Language

Demo

ISM Method

Low Power

English

Spanish

French

Digital Broadcasting System Captions

- Choose the language you want the DTV/CADTV Captions to appear in.

- Languages can be chosen for digital sources only if they are included on the program.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

G button and then use

D / E

button to select Caption/Text.

3. Press the G button and then use

D / E

button to select caption: CC1, CC2, CC3,

CC4, Text1, Text2, Text3, or Text4.

• CAPTION

The term for the words that scroll across the bottom of the TV screen; usually the audio portion of the program provided for the hearing impaired.

• TEXT

The term for the words that appear in a large black frame and almost cover the entire screen; usually messages provided by the broadcaster.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

G button and then use

D / E

button to select Caption/Text.

3. Press the

button and then use

D / E

button to select available caption lan-

guages: English, Spanish, or French.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

CABLE

Caption

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

G button and then use

D / E

button to select Caption.

3. Press the

G button and then use

D / E

button to select On or Off.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Aspect Ratio

Cinema

Caption G

Caption / Text

Caption Option

Language

Demo

ISM Method

Low Power

Off

CABLE

1. Use the CC button repeatedly to select Caption CC1, CC2, CC3, CC4, Text1, Text2, Text3, or Text4.

• EZ Mute shows the selected captions option (if available on program) when the TV sound is muted

.2. Press EXIT button to save and return to TV viewing.

• You can also use the OPTION menu to select Caption/Text.

Owner’s Manual 69

Operation

Option Menu Features continued

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Aspect Ratio

Cinema

Caption

Caption/Text

Caption Option G

Language

Demo

ISM Method

Low Power

Style Custom

Size A Standard

Font Font 0

Text Color White

Text Opacity Solid

Bg Color Black

Bg Opacity Solid

Edge Type None

Edge Color Black

Caption Option

- Customize the DTV/CADTV captions that appear on your screen.

1. Press the MENU button and then use

D / E

button to select the OPTION

menu.

2. Press the G button and then use

D / E

button to select Caption Option.

3. Press the G button and then use F / G button to select Custom.

4. Use

D / E

button to customize the Style, Font, etc., to your preference. A preview icon is provided at the bottom of the screen, use it to see the caption language.

• Size: Set the size the words will appear in.

• Font: Select a typeface for the words.

•

Text Color: Choose a color for the text.

•

Text Opacity: Specify the opacity for the text color.

• Bg (Background) Color: Select a background color.

• Bg (Background) Opacity: Select the opacity for the background color.

• Edge Type: Select an edge type.

• Edge Color: Select a color for the edges.

5. Press EXIT button to return to TV viewing or press MENU button to return

to the previous menu.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Aspect Ratio

Cinema

Caption

Caption/Text

Caption Option

Language

Demo G

ISM Method

Low Power

Demo

- EZ Demo Use to scan the features and menu options available on your TV.

- XD Demo Use to see the difference between XD Demo On and XD Demo Off.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the G button and then use

D / E

button to select Demo.

3. Press the G button and then use

D / E

button to select EZ Demo or XD Demo.

4. Press the

G button to start EZ Demo or XD Demo. Press EXIT button to stop EZ

Demo or XD Demo.

EZ Demo

Demo

CABLE

70 Plasma TV

Operation

- A frozen still picture from a PC/video game displayed on the screen for prolonged periods will result in an ghost image remaining; even when you change the image. Avoid allowing any fixed image to remain on the TV's screen for a long period of time.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the G button and then use

D / E

button to select ISM Method.

3. Press the G button and then use

D / E

button to select either Normal, White

wash

, Orbiter or Inversion.

• Normal If image sticking is never a problem, ISM is not necessary - set to Normal.

• White wash

White Wash removes permanent images from the screen. Note: An excessive permanent image may be impossible to clear entirely with White Wash. To return to normal viewing, press the any button.

• Orbiter

Orbiter may help prevent ghost images. However, it is best not to allow any

fixed image to remain on the screen. To avoid a permanent image on the

screen, the image will move once per minute: Right → Right → Downside →

Downside → Left → Left → Upside → Upside.

• Inversion

Inversion will automatically invert the plasma display panel color every 30 min-

utes.

4. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

ISM (Image Sticking Minimization) Method

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Aspect Ratio

Cinema

Caption

Caption/Text

Caption Option

Language

Demo

ISM Method G

Low Power

Normal White Wash Orbiter Inversion

Option Menu Features continued

CABLE

Owner’s Manual 71

Operation

1. Press the ZOOM button in DTV 720p, or 1080i modes.

2. Use the

D / E

/ F / G buttons to select the screen split zoom section.

3. To return to normal viewing, press the ZOOM button again.

Split Zoom (DTV 720p, or 1080i mode only)

- Enlarges the picture with correct proportions.

- When enlarging the picture, the image may become distorted.

Low Power

- Low power reduces the plasma display power consumption.

1. Press the MENU button and then use

D / E

button to select the OPTION menu.

2. Press the

G button and then use

D / E

button to select Low power.

3. Press the G button and then use

D / E

button to select On or Off.

• When you select On, the screen darkens.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

Owner’s Manual 71

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Aspect Ratio

Cinema

Caption

Caption / Text

Caption Option

Language

Demo

ISM Method

Low Power G

CABLE

Off

72 Plasma TV

Operation

Lock Menu Options

Parental Control can be used to block specific channels, ratings and other viewing sources.

The Parental Control Function (V-Chip) is used to block program viewing based on the ratings sent by the broadcasting station. The default setting is to allow all programs to be viewed. Viewing can be blocked by the type of program and by the categories chosen to be blocked. It is also possible to block all program viewing for a time period. To use this function, the following must be done :

1. Set ratings and categories to be blocked.

2. Specify a password

3. Enablethe lock

V-Chip rating and categories

Rating guidelines are provided by broadcasting stations. Most television programs and television movies can be blocked by TV Rating and/or Individual Categories. Movies that have been shown at the theaters or direct-to-video movies use the Movie Rating System (MPAA) only.

Ratings for Movies previously shown in theaters:

Movie Ratings :

• Blocking Off (Permits all programs)

• G (General audience)

• PG (Parental guidance suggested)

• PG-13 (Parents strongly cautioned)

• R (Restricted)

• NC-17 (No one 17 and under admitted)

• X (Adult only)

If you set PG-13 : G and PG movies will be available , PG-13, R, NC-17 and X will be blocked.

Ratings for Television programs including made-for-TV movies :

• TV-G (General audience)

• TV-PG (Parental guidance suggested)

• TV-14 (Parents strongly cautioned)

• TV-MA (Mature audience only)

• TV-Y (All children)

• TV-Y7 (Children 7 years older)

TV Rating Children:

• Age (applies to TV-Y, TV-Y7)

• Fantasy Violence (applies to TV-Y7)

TV Rating General:

• Age (applies to TV-G, TV-PG, TV-14, TV-MA)

• Dialogue - sexual dialogue (applies to TV-PG, TV-14)

• Language - adult language (applies to TV-PG, TV-14, TV-MA)

• Sex - sexual situations (applies to TV-PG, TV-14, TV-MA)

• Violence (applies to TV-PG, TV-14, TV-MA)

Aux. Block

• Video, Front Video (On, Off)

• Component 1, 2 (On, Off)

• RGB, HDMI/DVI (On, Off)

Owner’s Manual 73

Operation

Parental Lock Setup

1. Press the MENU button and then use

D / E

button to select the LOCK menu.

Then, press the

G button

• If Lock is already set, enter the password as requested.

• The TV is set up with the initial password “0-0-0-0”.

2. Use the

D / E

button to choose from the following Lock Menu options. Once the

option is selected, change the settings to your preference.

• Lock System: Activates or disables the blocking scheme you set up previ-

ously.

• Set Password: Change the password by inputting a new password twice.

• Movie Rating (MPAA): Blocks movies according to the movie ratings lim-

its specified, so children cannot view certain movies. You can set the ratings limit by blocking out all the movies with the ratings above a specified level. Keep in mind that the movie ratings limit only applies to movies shown on TV, not TV programs, such as soap operas.

• TV Rating-Children: Prevents children from watching certain children's TV

programs, according to the ratings limit set. The children rating does not apply to other TV programs. Unless you block certain TV programs intended for mature audiences in the TV Rating - sub menu, your children can view those programs.

• TV Rating-General: Based on the ratings, blocks certain TV programs that

you and your family do not want to view.

• Aux. Block: Enables you to select a source to block from the external

source devices you have hooked up.

3. Press EXIT button to return to TV viewing or press MENU button to return to

the previous menu.

Note

• If you ever forget your password, key in ‘7’, ‘7’, ‘7’, ‘7’ on the remote control.

- Set up blocking schemes to block specific channels, ratings, and external viewing sources.

- A password is required to gain access to this menu if the Lock System is turned on.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

Lock System G

Set Password

Block Channel

Movie Rating

TV Rating-Children

TV Rating-General

Aux. Block

Off

CABLE

74 Plasma TV

Operation

CableCARD

CableCARD™

Function

Cable menu options

- The Cable sub menu displays when inserting the CableCARDTMto the TV.

- The CableCARDTMtype is Motorola, Scientific Atlanta (SA), or SCM etc. The OSD (On screen display) is different from your TV according to your CableCARDTMtype.

Scrambled channel

- Insert the CableCARDTM. If you do it at first, it takes about 1 minute to exchange the data between the TV and the CableCARDTM. Then, TV screen displays as shown right.

- Let your cable TV service provider know CableCARDTMID and Host ID.

- If your cable TV service provider is registered CableCARDTMID and Host ID, you can watch the premium or high value channel.

- If you ever registered to the cable TV service provider, you can watch the premium or high value channel without a message.

- If the certificate don’t match between the TV and the CableCARD

the OSD (On screen display) displays as shown left.

In case of Scientific Atlanta CableCARD™

i.e) CableCARD™/ Host ID Screen

1. Press the MENU button and then use

D / E

button to select the CABLE menu.

2. Press the G button and then use

D / E

button to select your desired item.

3. Press the G button.

5. Press EXIT button to return to TV viewing.

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

CABLE

SA CableCARD™ Diag Screen G

SA CableCARD™/Host ID Screen

Exit

In order to start service for this device, please contact customer service at Ph#: 1-866-303-0422

CableCARD™(tm): 0-010-405-698-001 HOST ID: 0-080-000-000-226

EXIT

CableCARD™ Message

Exit

In order to start cable service for this device, please contact SuperVision Cable at 1-800-555-8888

POD ID: 7-561-034-449-009

Host ID: 0-100-331-784-018

EXIT

CableCARD™ Message

Please call your operator and report an invalid CableCARDTM.

* In this manual, the OSD (On Screen Display) may be different from your TV’s because it is just example to help

the TV operation.

As shown, the pairing number means your TV and CableCARDTMID. For further information regarding cable TV service, contact your local cable TV service provider(s).

Owner’s Manual 75

Operation

- If an emergency situation occur during watching the TV, you can receive a message from cable TV service provider(s).

- When receiving an emergency message, the message is displayed on the screen as shown below or the channel is changed automatically to a channel that maintains the emergency message. The message automatically disappeared.

Emergency Action Notification

Hurricane will be coming!!!

Cable Channel List

Emergency

Alert Message

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

CABLE

Prev.

EZ Scan

Manual Scan

Channel Edit G

DTV Signal

Channel Label

Main Input

Sub Input

Aux. Label

Selection ( Gor ) leads you

to the channel edit screen.

1. Begin the Cable channel search with EZ Scan .

2. If you enter the

Channel Edit after running the EZ Scan, you can see the cable channel list.

3. Inserting the CableCARDTM. Then, the TV receive a new cable channel list. At this time, it takes about 2~3 minutes.

(Occasionally more than that time).

Note:

• As data gathering of CableCARDTM, it may make a noise by fan in standby mode.

1. 2.

3. 4.

76 Plasma TV

Operation

WWatching PIP/POP/T

atching PIP/POP/T

win Picture

- PIP lets you view 2 different inputs (sources) on your TV screen at the same time. One source will be large, and the other source will show a smaller inset image.

- Twin Picture mode splits the screen into 2, allowing 2 picture sources to be shown on the TV screen at the same time. Each source is given half the screen.

- If you set the block/rating for Lock menu options in PIP/Twin Picture mode, “Rating Blocked” doesn’t display on screen.

Press the PIP button to access the sub picture. Each press of PIP changes the PIP options as shown below.

PIP Off

PIP Mode POP Mode Twin Picture Mode

TV Program selection for PIP

1. Press the PIP button.

2. Select the Antenna or Cable option on the Sub input menu or with the PIP INPUT button. Use the PIPCH+

PIPCH- button to select a channel for the sub picture.

(You can’t select DTV for main and sub picture simultaneously).

Swapping the PIP

Swapping the PIP/T/T

win Picture

Repeatedly, use the SWAP button to switch the main and sub pictures.

• Component 1, Component 2, RGB-PC (or RGB-DTV), HDMI/DVI input sources for the main picture can’t be used to

swap the main and sub pictures.

Selecting an Input Signal Source for PIP/T

win Picture

Use the PIP INPUT button to select the input source for the sub picture. Each press of PIP INPUT button changes the PIP source. You can also select sources for the Sub Input in the SETUP menu.

Main Picture Source

Available Sub Picture Sources

DTV Analog

Analog, Video, and Front Video DTV, Analog, Video, and Front Video

Main Picture Sub Picture

F TV 2-0

TV 4-0

TV 6-0

Remote Control

PIP

(Picture-In-Picture) / POP

/ T

win Picture

Owner’s Manual 77

Operation

Moving the PIP

sub picture

In PIP mode, press the

D / E

/ F / G button to move the sub picture to a different location on the

screen.

Adjusting Main and Sub Picture Sizes for

Adjusting Main and Sub Picture Sizes for TT

win Picture

Use the

D / E

/ F / G button to change main and sub picture sizes in Twin Picture mode.

1. Press the PIP button to activate the POP mode while in PIP mode.

• Channel selection: Use F button to enlarge the selected channel being searched on the PIP

screen to shift it for viewing on the Main screen.

• PIP selection: Use

D / E

button to select one of 3 PIP screen pictures in POP mode.

• When watching TV on Main picture, TV or DTV on Sub pictures are in channel scanning.

However, when watching DTV on Main picture, only TV on Sub picture is in channel scanning.

2. Press the EXIT button to cancel POP mode.

POP

(Picture-out-of-Picture: Channel Scan)

- Use POP to search the programs of all the memorized channels one-by-one on the 3 PIP screen display, (while the main picture source remains the current channel). The pictures of all the programmed channels are searched with the 3 POP screen.

- Note:

•Run EZ Scan channel search before using POP mode.

•When Sub pictures are changed from the TV/DTV to CATV/CADTV in POP mode, it may make a noise

from the Tuner switch.

F TV 2-0

TV 4-0

TV 6-0

If screen is adjusted to the maximal size, the large screen is filled with entire screen vertically as shown.

i.e)

78 Plasma TV

Operation

3:11AM

Sophie’s Choice

Tue, Oct 7, 2004

7:00PM

9:00PM

Caption

4 : 3

480i

TV-PG

D L S V

TV 6-0

CNBC

MONO

STEREO

4 : 3

16 : 9

Screen Ratio of Input Signal 4:3

Screen Ratio of Input Signal 16:9

Resolution of Input Signal 720x480i

Resolution of Input Signal 720x480p

Resolution of Input Signal 1280x720p

Resolution of Input Signal 1920x1080i

Multilingual : Input Signal have over two Audio infor-

mation. Press the SAP button to select wanted Audio.

Caption: Input Signal have over one Close service.

Press the CC button to select wanted Closed caption.

Input Signal have rating information . Refer to the

<Lock Menu>.

D (Dialogue), L (Language), S (Sex), V (Violence), FV

(Fantasy Violence)

480i 480p 720p

1080i

Operation: • Watching TV/DTV/CATV/CADTV

• Watching Video, Front Video

• Watching IEEE 1394

• In Component1, Component2, RGB,

HDMI/DVI modes, INFO button is not working.

Function: • Show the present screen information.

• On Watching with the upper Input signal,

press the INFO button.

• Press the INFO button or EXIT button to

exit.

A: Banner information, Refer to the

<Channel Banner>. B: Program title C: Day, Month, Year D: Program start time E: Program finish time F: Show the prosessing rate G: Present time H: Added information. Refer to the icon

explanation.

Information

Owner’s Manual 79

Operation

- Nothing to do with Caption on/Off using Mute button, the mode selected Caption/Text is to be displayed.

- When you repeatedly press the Mute button, the screen is displayed in turn. (Refer to the lower picture)

Note:

• EZ Mute only operates in DTV/Analog/Video/Front Video/IEEE1394.

EZ Mute

Mute

EZ Mute

80 Plasma TV

External Control Device Setup

No. Pin Name 1 No connection 2 RXD (Receive data) 3 TXD (Transmit data) 4 DTR (DTE side ready) 5 GND 6 DSR (DCE side ready) 7 RTS (Ready to send) 8 CTS (Clear to send) 9 No Connection

2 3 5 4 6 7 8

RXD

TXD

GND

DTR DSR

RTS CTS

TXD RXD

GND

DSR DTR CTS RTS

7-Wire Configurations

(Standard RS-232C cable)

D-Sub 9

3 2 5 6 4 8 7

PDP

D-Sub 9

2 3 5 4 6 7 8

RXD TXD

GND

DTR DSR RTS CTS

TXD RXD

GND

DTR DSR RTS CTS

3-Wire Configurations

(Not standard)

D-Sub 9

3 2 5 4 6 7 8

PDP

D-Sub 9

- Connect the RS-232C input jack to an external control device (such as a computer or an A/V control system) and control the Monitor’s functions externally.

- Connect the serial port of the control device to the RS-232C jack on the Monitor back panel.

- RS-232C connection cables are not supplied with the Monitor.

TType of Connector; D-Sub 9-Pin Male

ype of Connector; D-Sub 9-Pin Male

RS-232C Configurations

External Control Device Setup

RS-232C Setup

DVI

COMPONENT2

DIGITAL AUDIO(OPTICAL)

VIDEO INPUT

AUDIO INPUT

CABLE

HDMI / DVI(VIDEO)

Cable

ANTENNA

AC INPUT

Owner’s Manual 81

External Control Device Setup

Set ID

Use this function to specify a monitor ID number. Refer to ‘Real Data Mapping’. See page 82.

• Baud rate : 9600 bps (UART)

• Data length : 8 bits

• Parity : None

* Use a crossed (reverse) cable.

• Stop bit : 1 bit

• Communication code : ASCII code

Communication Parameters

1. Press the MENU button and then use

D / E

button to select the SETUP menu.

2. Press the G button and then use

D / E

button to select SET ID.

3. Press the G button and then use

D / E

button to adjust SET ID to choose the

desired monitor ID number. The adjustment range of SET ID is 1 ~ 99.

4. Press EXIT button to return to TV viewing or press MENU button to return to the

previous menu.

ransmission

[Command 1]: First command to control the set. (j or k)

[Command 2]: Second command to control the set.

[Set ID]: You can adjust the set ID to choose desired monitor

ID number in Setup menu. Adjustment range is 1 ~ 99. When selecting Set ID ‘0’, every connected the TV is controlled. Set ID is indicated as decimal (1~99) on menu and as Hexa decimal (0x0~0x63) on transmission/receiving protocol.

[DATA]: To transmit command data.

Transmit ‘FF’ data to read status of command.

[Cr]: Carriage Return

ASCII code ‘0x0D’

[ ]: ASCII code ‘space (0x20)’

[Command1][Command2][ ][Set ID][ ][Data][Cr]

TTransmission / Receiving Protocol

ransmission / Receiving Protocol

Acknowledgement

* The Monitor transmits ACK (acknowledgement) based on

this format when receiving normal data. At this time, if the data is data read mode, it indicates present status data. If the data is data write mode, it returns the data of the PC computer.

[Command2][ ][Set ID][ ][OK][Data][x]

Error

Acknowledgement

* The Monitor transmits ACK (acknowledgement) based on

this format when receiving abnormal data from non-viable functions or communication errors.

[Command2][ ][Set ID][ ][NG][Data][x]

Data 1: Illegal Code

2: Not supported function 3: Wait more time

01. Power k a 0 ~ 1

02. Input Select k b 0 ~ 8

03. Aspect Ratio k c 0 ~ 15

04. Screen Mute k d 0 ~ 1

05. Volume Mute k e 0 ~ 1

06. Volume Control k f 0 ~ 64

07. Contrast k g 0 ~ 64

08. Brightness k h 0 ~ 64

09. Color k i 0 ~ 64

10. Tint k j 0 ~ 64

11. Sharpness k k 0 ~ 64

12. OSD Select k l 0 ~ 1

13.

Remote Control Lock Mode

k m 0 ~ 1

14. PIP/Twin k n 0 ~ 3

15. PIP Position k q 0 ~ 3

16. Treble k r 0 ~ 64

17. Bass k s 0 ~ 64

18. Balance k t 0 ~ 64

19. Color Temperature k u 0 ~ 2

20. PIP Input Source k y 0 ~ 3

21. ISM Method j p 0 ~ 2

22. White Wash j q 0 ~ 1

23. Orbiter Time Setting j r 1 ~ FE

24. Orbiter Pixel Setting j s 1 ~A

COMMAND 1 COMMAND 2 DATA

(Hexadecimal)

25. Channel Tuning m a 01 ~ 87 01 ~ 87 00 ~ FE 00 ~ FF

26. Channel Add/Del m b 00 ~ 01

27. Key m c

COMMAND 2

COMMAND 1

DATA 0

(Hexadecimal)

DATA 1

(Hexadecimal)

DATA 2

(Hexadecimal)

DATA 3

(Hexadecimal)

Command Reference List

SETUP

VIDEO

AUDIO

TIME

OPTION

LOCK

EZ Scan

Manual Scan

Channel Edit

DTV Signal

Channel Label

Main Input

Sub Input

Aux. Label

SET ID G

82 Plasma TV

External Control Device Setup

02. Input Select (Command2:b) (Main Picture Input)

G To select input source for the Monitor.

ransmission

Data 0: Antenna

1: Cable 2: Video 3: Front Video 4: Component 1

5: Component 2 6: RGB-DTV 7: RGB-PC 8: HDMI/DVI

Data 0: Set by program

1: 4:3 2: 16:9 3: Horizon 4: Zoom 1

5: Zoom 2 6: Cinema Zoom (1)

15: Cinema Zoom (16)

[k][b][ ][Set ID][ ][Data][Cr]

Acknowledgement

[b][ ][Set ID][ ][OK][Data][x]

01. Power (Command2:a)

G To control Power On/Off of the Monitor.

Transmission

Data 0 : Power Off 1 : Power On

[k][a][ ][Set ID][ ][Data][Cr]

Acknowledgement

[a][ ][Set ID][ ][OK][Data][x]

* In a like manner, if other functions transmit ‘FF’ data

based on this format, Acknowledgement data feedback presents status about each function.

Real data mapping

0 : Step 0

A : Step 10 (SET ID 10)

F : Step 15 (SET ID 15)

10 : Step 16 (SET ID 16)

63 : Step 99 (SET ID 99) 64 : Step 100

05. Volume Mute (Command2:e)

G To control volume mute on/off.

You can also adjust mute using the MUTE button on remote control.

ransmission

Data 0 : Volume mute off (Volume on)

1 : Volume mute on (Volume off)

[k][e][ ][Set ID][ ][Data][Cr]

Acknowledgement

[e][ ][Set ID][ ][OK][Data][x]

03. Aspect Ratio (Command2:c) (Main picture format)

G To adjust the screen format.

You can also adjust the screen format using the RATIO button on remote control or in the Option menu.

ransmission

[k][c][ ][Set ID][ ][Data][Cr]

Acknowledgement

[c][ ][Set ID][ ][OK][Data][x]

04. Screen Mute (Command2:d)

G To select screen mute on/off.

Transmission

Data 0 : Screen mute off (Picture on)

1 : Screen mute on (Picture off)

[k][d][ ][Set ID][ ][Data][Cr]

Acknowledgement

[d][ ][Set ID][ ][OK][Data][x]

06. Volume Control (Command2:f)

G To adjust volume.

You can also adjust volume with the volume buttons on remote control.

ransmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping’ as shown below.

[k][f][ ][Set ID][ ][Data][Cr]

Acknowledgement

[f][ ][Set ID][ ][OK][Data][x]

07. Contrast (Command2:g)

G To adjust screen contrast.

You can also adjust contrast in the Video menu.

ransmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping’ as shown below.

[k][g][ ][Set ID][ ][Data][Cr]

Acknowledgement

[g][ ][Set ID][ ][OK][Data][x]

08. Brightness (Command2:h)

G To adjust screen brightness.

You can also adjust brightness in the Video menu.

Transmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping’ as shown below.

[k][h][ ][Set ID][ ][Data][Cr]

Acknowledgement

[h][ ][Set ID][ ][OK][Data][x]

Owner’s Manual 83

External Control Device Setup

09. Color (Command2:i)

G To adjust the screen color.

You can also adjust color in the Video menu.

Transmission

Data Min : 0 ~ Max : 64

• Refer to ‘Real data mapping’. See page 82.

[k][i][ ][Set ID][ ][Data][Cr]

Acknowledgement

[i][ ][Set ID][ ][OK][Data][x]

10. Tint (Command2:j)

G To adjust the screen tint.

You can also adjust tint in the Video menu.

ransmission

Data Red : 0 ~ Green : 64

• Refer to ‘Real data mapping’. See page 82.

[k][j][ ][Set ID][ ][Data][Cr]

Acknowledgement

[ j ][ ][Set ID][ ][OK][Data][x]

13. Remote Control Lock Mode (Command2:m)

G To lock the remote control and the front panel controls on

the set.

ransmission

[k][m][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: Lock off 1: Lock on

[m][ ][Set ID][ ][OK][Data][x]

14. PIP / POP / Twin Picture (Command2:n)

G To control the PIP (Picture-in-Picture)/POP/Twin picture.

You can also control the PIP/POP/Twin picture using the PIP button on the remote control.

ransmission

Data 0: PIP off

1: PIP

2: POP 3: Twin Picture

[k][n][ ][Set ID][ ][Data][Cr]

Acknowledgement

[n][ ][Set ID][ ][OK][Data][x]

G To adjust the screen sharpness.

You can also adjust sharpness in the Video menu.

Transmission

11. Sharpness (Command2:k)

Data Min: 0 ~ Max: 64

•

Refer to ‘Real data mapping’. See page 82.

[k][k][ ][Set ID][ ][Data][Cr]

Acknowledgement

[k][ ][Set ID][ ][OK][Data][x]

12. OSD Select (Command2:l)

G To select OSD (On Screen Display) on/off.

ransmission

[k][l][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: OSD off 1: OSD on

[l][ ][Set ID][ ][OK][Data][x]

15. PIP Position (Command2:q)

G To select sub picture position for PIP.

Transmission

[k][q][ ][Set ID][ ][Data][Cr]

Acknowledgement

Data 0: Right down on screen

1: Left down on screen 2: Left up on screen 3: Right up on screen

[q][ ][Set ID][ ][OK][Data][x]

16. Treble (Command2:r)

G To adjust treble.

You can also adjust treble in the Audio menu.

ransmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping’. See page 82.

[k][r][ ][Set ID][ ][Data][Cr]

Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

18. Balance (Command2:t)

G To adjust balance.

You can also adjust balance in the Audio menu.

ransmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping’. See page 82.

[k][t][ ][Set ID][ ][Data][Cr]

Acknowledgement

[t][ ][Set ID][ ][OK][Data][x]

17. Bass (Command2:s)

G To adjust bass.

You can also adjust bass in the Audio menu.

ransmission

Data Min: 0 ~ Max: 64

• Refer to ‘Real data mapping’. See page 82.

[k][s][ ][Set ID][ ][Data][Cr]

Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

84 Plasma TV

External Control Device Setup

19. Color Temperature (Command2:u)

G To adjust color temperature.

You can also adjust color temperature in the Video menu.

ransmission

Data 0: Cool 1: Medium 2: Warm

[k][u][ ][Set ID][ ][Data][Cr]

Acknowledgement

[u][ ][Set ID][ ][OK][Data][x]

23. Orbiter Time Setting (Command2:r)

G To adjust orbiter operation time term.

Transmission

Data Min: 1 ~ Max: FE

[ j ][r][ ][Set ID][ ][Data][Cr]

Acknowledgement

[r][ ][Set ID][ ][OK][Data][x]

24. Orbiter Pixel Setting (Command2:s)

G To adjust pixel number in orbiter function.

Transmission

Data Min: 1 ~ Max: A

[ j ][s][ ][Set ID][ ][Data][Cr]

Acknowledgement

[s][ ][Set ID][ ][OK][Data][x]

25. Tune Command (Command: m a)

G To tune channel to following physical/major/minor number

ransmission

Data 0:

Physical channel number Min: 1~ Max: 0x87

Data 1, Data 2:

Major Channel Number (two part)/ Channel Number (One part) (Data 1: High, Data 2: Low)

Data 3, Data 4:

Minor Channel Number (Data3: High, Data4: Low)

Data 5:

*All data are transmitted by Hexadecimal code Example) If you want PIP channel tuned to ATSC air (standard)

30-5, the command sequence is ma 00 1e 00 1e 00 05 82.

[m][a][ ][Set ID][ ][Data0][ ][Data1][ ][Data2][ ][Data3][ ][Data4][ ][Data5][Cr]

[a][ ][Set ID][ ][OK][Data0][Data1][Data2][Data3][Data4][x] [a][ ][Set ID][ ][NG][Data0][x]

Acknowledgement

26. Channel Add/Del (Command: m b)

G To add and delete the channels

Transmission

Data 0: Channel Delete

1: Channel Add

[m][b][ ][Set ID][ ][Data][Cr]

[b][ ][Set ID][ ][OK][Data][x] [b][ ][Set ID][ ][NG][Data][x]

Acknowledgement

27. Key (Command: m c)

G To send IR remote key code

ransmission

Data Key code: Refer to page 86.

* It’s impossible to command the IR Code 0x08 and 0xC4

with RS-232C.

[m][c][ ][Set ID][ ][Data][ ][Cr]

[c][ ][Set ID][ ][OK][Data][x]

Acknowledgement

20. PIP Input Select (Command2:y)

G To select input source for sub picture in PIP/Twin pic-

ture mode.

ransmission

Data 0: Antenna

1: Cable 2: Video 3: Front Video

[k][y][ ][Set ID][ ][Data][Cr]

Acknowledgement

[y][ ][Set ID][ ][OK][Data][x]

21. ISM Method (Command2:p)

G To avoid having a fixed image remain on screen.

Transmission

Data 0: Normal

1: Orbiter 2: Inversion

[ j ][p][ ][Set ID][ ][Data][Cr]

Acknowledgement

[p][ ][Set ID][ ][OK][Data][x]

22. White Wash (Command2:q)

G To control the white wash function on/off.

You can also adjust white wash in Option menu.

ransmission

Data 0: White Wash off

1: White Wash on

[ j ][q][ ][Set ID][ ][Data][Cr]

Acknowledgement

[q][ ][Set ID][ ][OK][Data][x]

Main/Sub Picture

Two/One

Part

Channel

Reserved4Reserved

Step

01Main

Sub

Two

One

NTSC Air

ATSC cable

ATSC

Cable_irc

ATSC

Cable_hrc

ATSC

Cable_std

NTSC Cable

ATSC Air

Reserved

...

Reserved

Owner’s Manual 85

IR Codes

G Connect your wired remote control to the Remote Control port on the TV.

G Output waveform

Single pulse, modulated with 37.917KHz signal at 455KHz

G Configuration of frame

G Repeat code

G Lead code

• 1st frame

Low custom code

Lead

code

High custom code

Data code

Carrier frequency

CAR = 1/TC = fOSC/12

Duty ratio = T1/TC = 1/3

• Repeat frame

C1 C2 C3 C4 C5 C6 C7 C0 C1 C2 C3 C4 C5 C6 C7 D0 D1 D2 D3 D4 D5 D6 D7 D0 D1 D2 D3 D4 D5 D6 D7

Repeat code

9 ms 4.5 ms

0.55 ms

9 ms

2.25 ms

G Bit description

G Frame interval : Tf

The waveform is transmitted as long as a key is depressed.

• Bit “0”

Tf Tf

Tf=108ms @455KHz

0.56 ms 0.56 ms

1.12 ms

• Bit “1”

2.24 ms

How to Connect

Remote Control IR Codes

IR Codes

86 Plasma TV

IR Codes

08 C4 C5 98 79 0E 10 ~ 19 4C 1A 09 02 03 00 01 1E AA 39 40 41 07 06 44 43 52 4D 5B 60 72 71 61 63 65 7B 0A CB D6 5A D0 BF D4 D5 D7 C6 76 77 AF 70 96 87 B0 BA B1 BD 8F 8E B2 B3 A9

R/C Button R/C Button R/C Button (Power On/Off) Discrete IR Code (Only Power On) Discrete IR Code (Only Power Off) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button Discrete IR Code (TV Input Selection) Discrete IR Code (Video Input Selection) Discrete IR Code (Front Video Input Selection) Discrete IR Code (Component1 Input Selection) Discrete IR Code (Component2 Input Selection) Discrete IR Code (RGB-PC Input Selection) Discrete IR Code (RGB-DTV Input Selection) Discrete IR Code (HDMI/DVI Input Selection) Discrete IR Code (Only 4:3 Mode) Discrete IR Code (Only 16:9 Mode) Discrete IR Code (Only Zoom1 Mode) Discrete IR Code (Channel Search) R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button R/C Button

Code (Hexa) Function Note

TV/VIDEO MODE POWER POWER ON POWER OFF COMP/RGB RATIO TIMER Number Key 0~ 9

- (Dash) FLASHBK MUTE VOL + VOL CH + CH SURF INFO CC

D E F G

ENTER MENU SOUND VIDEO EXIT PIP PIPCH PIPCH + PIP INPUT SWAP FREEZE ZOOM SAP ADJUST TV VIDEO Front Video COMPONENT 1 COMPONENT 2 RGB-PC RGB-DTV HDMI/DVI Ratio 4:3 Ratio 16:9 Ratio Zoom POP SIGNAL 1394 PLAY PAUSE STOP REC REW FF GOTOPREV GOTONEXT TV GUIDE

Owner’s Manual 87

Programming the Remote

G The remote control is a multi-brand or universal remote control. It can be programmed to operate most remote-controllable

devices of other manufacturers. Note that the remote control may not control all models of other brands.

Programming a code into a remote mode

Programming the Remote

1. Test your remote control. To find out whether your remote control can operate the component without programming, turn on the component such as a VCR and press the corresponding MODE button (VCR) on the remote control, while pointing at the component. Test the POWER and CH +/- buttons to see if the component responds properly. If not, the remote requires programming to operate the device.

2. Turn on the component to be programmed, then press the corresponding MODE button on the remote control.

3. Press the MENU and MUTE buttons simultaneously, the remote control is ready to be programmed for the code.

4. There are two ways to find the right code for the component. A. If you press the CH +/- buttons repeatedly, the codes will change one at-a-time. Press the POWER button after each code

change. If the right code is found, the device will turn off.

B. Enter a code number using the number buttons on the remote. Programming code numbers for the corresponding component

can be found on the following pages. Again, if the code is correct, the device will turn off.

5. Press the MENU button to store the code.

6. Test the remote control functions to see if the component responds properly. If not, repeat from step 2.

88 Plasma TV

Programming Codes

VCRs

CACATV

AIWA 034 AKAI 016 043 046 124

125 146 AMPRO 072 ANAM 031 033 103 AUDIO DYNAMICS

012 023 039 043 BROKSONIC 035 037 129 CANON 028 031 033 CAPEHART 108 CRAIG 003 040 135 CURTIS MATHES 031 033 041 DAEWOO 005 007 010 064

06 5 1 08 110 111

112 11 6 117 119 DAYTRON 108 DBX 012 023 039 043 DYNATECH 034 053 ELECTROHOME 059 EMERSON 006 017 025 027

029 031 034 035

036 037 046 101

129 131 138 153 FISHER 003 008 009 010 FUNAI 034 GE 031 033 063 072

107 109 144 147 GO VIDEO 132 136 HARMAN KARDON

012 045 HITACHI 004 018 026 034

043 063 137 150 INSTANTREPLAY 031 033 JCL 031 033 JCPENNY 012 013 015 033

040 066 101 JENSEN 043 JVC 012 031 033 043

048 050 055 060

130 150 152

KENWOOD 014 034 039 043

047 048

LG (GOLDSTAR) 001 012 013 020

101 106 114 123 LLOYD 034 LXI 003 009 013 014

017 034 101 106 MAGIN 040 MAGNAVOX 031 033 034 041

067 068 MARANTZ 012 031 033 067

069 MARTA 101 MATSUI 027 030 MEI 031 033 MEMOREX 003 010 014 031

033 034 053 072

101 102 134 139 MGA 045 046 059 MINOLTA 013 020 MITSUBISHI 013 020 045 046

049 051 059 061

151 MTC 034 040 MULTITECH 024 034 NEC 012 023 039 043

048 NORDMENDE 043 OPTONICA 053 054 PANASONIC 066 070 074 083

133 140 145 PENTAX 013 020 031 033

063 PHILCO 031 034 067 PHILIPS 031 033 034 054

067 071 101 PILOT 101 PIONEER 013 021 048

PORTLAND 108 PULSAR 072 QUARTZ 011 014 QUASAR 033 066 075 145 RCA 013 020 033 034

040 041 062 063 107 109 140 144 145 147

REALISTIC 003 008 010 014

031 033 034 040

053 054 101 RICO 058 RUNCO 148 SALORA 014 SAMSUNG 032 040 102 104

105 107 109 112

113 115 120 122

125 SANSUI 022 043 048 135 SANYO 003 007 010 014

102 134 SCOTT 017 037 112 129

131 SEARS 003 00 009 010 013 014 017 020

031 042 073 081

101 SHARP 031 054 149 SHINTOM 024 SONY 003 009 031 052

056 057 058 076

077 078 149 SOUNDESIGN 034 STS 013 SYLVANIA 031 033 034 059

067 SYMPHONIC 034 TANDY 010 034

TATUNG 039 043 TEAC 034 039 043 TECHNICS 031 033 070 TEKNIKA 019 031 033 034

101 THOMAS 034 TMK 006 TOSHIBA 008 013 042 047

059 082 112 131 TOTEVISION 040 101 UNITECH 040

VECTOR RESEARCH

012 VICTOR 048 VIDEO CONCEPTS

012 034 046 VIDEOSONIC 040 WARDS 003 013 017 024

031 033 034 040

053 054 131 YAMAHA 012 034 039 043 ZENITH 034 048 056

058 072 080 101

Brand Codes Brand Codes Brand Codes Brand Codes

ABC 003 004 039 042

046 052 053 AJIN 112 ANTRONIK 014 ARCHER 005 007 014 024 CABLE STAR 026 CENTURION 092 CENTURY 007 CITIZEN 007 COLOUR VOICE 065 090 COMBANO 080 081 COMTRONICS 019 030 DIAMOND 023 EAGLE 020 030 040 EASTERN 057 062 066 ELECTRICORD 032 GE 072 GEMINI 008 022 025 054 GI 052 074

GOLDEN CHANNEL

030 HAMLIN 049 050 055 HITACHI 052 055 HOSPITALITY 070 077 JERROLD 002 003 004 008

009 010 052 069

074 LG (GOLDSTAR) 001 106 101 005 M-NET 037 MACOM 033 MAGNAVOX 010 012 064 079 MEMOREX 100 MOVIE TIME 028 032 NSC 015 028 038 071

073 OAK 016 031 037 053 PANASONIC 044 047 PARAGON 100 PHILIPS 006 012 013 020

065 085 090

PIONEER 034 051 052 063

076

POST NEWS WEEK

016 PRUCER 059 PTS 011 048 071 072

073 074 PULSAR 100 RCA 047 REGAL 049 050 REGENCY 057 REMBRANT 025 RK 091 SAMSUNG 102 107 030 068

SCIENTIFIC ATLANTA

003 011 041 042

043 045 046 SHERITECH 022 SIGNAL 030 SIGNATURE 052

SL MARX 030 SPRUCER 047 078 STARCOM 002 004 008 009 STARGATE 008 030 SYLVANIA 067 TADIRAN 030 TAEKWANG 110 TAIHAN 105 TANDY 017 TEXSCAN 029 067 TOCOM 039 040 056 TOSHIBA 100 UNIKA 007 014 024 UNITED CABLE 004 053 UNIVERSAL 005 007 014 024

026 027 032 035

VIEWSTAR 012 015 018 086

087 088 089

ZENITH 100 114 060 093

Owner’s Manual 89

Programming Codes

Audio

APEX DIGITAL 022 DENON 020 014 GE 005 006 HARMAN KARDON 027 JVC 012 LG 001 010 016 025

MAGNAVOX 013 MARANTZ 024 MITSUBISHI 002 NAD 023 ONKYO 008 017 PANASONIC 003 009

PHILIPS 013 PIONEER 004 026 PROCEED 021 PROSCAN 005 006 RCA 005 006 SAMSUNG 011 015

SONY 007 THOMPSON 005 006 TOSHIBA 019 008 YAMAHA 009 018 ZENITH 010 016 025

DVD

ALPHASTAR DSR

123 AMPLICA 050 BIRDVIEW 051 126 129 BSR 053 CAPETRONICS 053 CHANNEL MASTER

013 014 015 018

036 055 CHAPARRAL 008 009 012 077 CITOH 054 CURTIS MATHES 050 145 DRAKE 005 006 007 010

011 052 112 116

141 DX ANTENNA 024 046 056 076 ECHOSTAR 038 040 057 058

093 094 095 096

097 098 099 100

122 ELECTRO HOME 089

EUROPLUS 114 FUJITSU 017 021 022 027

133 134

GENERAL INSTRUMENT

003 004 016 029 031 059 101

HITACHI 139 140

HOUSTON TRACKER

033 037 039 051

057 104 HUGHES 068 HYTEK 053 JANIEL 060 147 JERROLD 061 KATHREIN 108 LEGEND 057 LG 001 LUTRON 132 LUXOR 062 144 MACOM 010 059 063 064

065

MEMOREX 057 NEXTWAVE 028 124 125 NORSAT 069 070

PACE SKY SATELLITE 143

PANASONIC 060 142 PANSAT 121 PERSONAL CABLE 117 PHILIPS 071 PICO 105 PRESIDENT 019 102 PRIMESTAR 030 110 111 PROSAT 072 RCA 066 106 REALISTIC 043 074 SAMSUNG 123

SATELLITE SERVICE CO

028 035 047 057 085

SCIENTIFIC ATLANTA

032 138

SONY 103

STARCAST 041 SUPER GUIDE 020 124 125 TEECOM 023 026 075 087

088 090 107 130

137 TOSHIBA 002 127 UNIDEN 016 025 042 043

044 045 048 049

078 079 080 086

101 UNIDEN 135 136 VIEWSTAR 115 WINEGARD 128 146 ZENITH 081 082 083 084

091 120

HDSTB

Brand Codes Brand Codes Brand Codes Brand Codes

AIWA 014 028 070 096

125 129 139 229

230 AKAI 163 ANAM 003 014 017 023

059 106 189 216

217 235 236 BURMECTER 252 CARVER 086 CLARION 199 DAEWOO 027 053 060 084

102 148 198 221 DENON 015 075 130 143 FANTASIA 071 FINEARTS 022 FISHER 089 099 LG(GOLDSTAR) 001 021 024 029

087 107 108 110

190 191 192 210

211 212 239 HAITAI 034 035 188 222 HARMAN/KARDON 068 INKEL 037 058 062 069

078 079 095 121

122 149 150 151

152 153 154 155

157 158 159 160

189 207 222 224

225 226 227 243

247

JVC 004 013 141 KEC 185 186 187 KENWOOD 038 050 067 089

170 171 197 206

215 222 KOHEL 030 NAD 045 046 LOTTE 014 016 036 098

100 172 173 174

175 176 177 178

179 180 181 183

201 202 208 213

214 219 223 232

238 240 LXI 103 MAGNAVOX 111 MARANTZ 002 018 020 025

034 041 081 090

097 112 MCINTOSH 049 MCS 104 MEMOREX 107 NAD 046 ONKYO 013 040 041 047

048 056 057 132

133 140 OPTIMUS 158 PANASONIC 007 033 064 113

142 220 241 251 PENNEY 104

PHILIPS 026 112 143 253 PIONEER 039 042 043 063

065 091 093 094

115 123 127 250 QUASAR 113 RCA 080 RCX 092 REALISTIC 103 106 SAMSUNG 124 145 146 182

193 194 195 203

204 244 245 246 SANSUI 011 135 138 144 SANYO 019 083 234 SCOTT 106 186 SHARP 031 032 051 052

072 082 117 119

156 184 199 200

206 209 SHERWOOD 005 006 158 SONY 044 045 109 114

118 126 248 249 TAEKWANG 012 020 073 074

076 077 105 161

162 163 164 165

166 167 168 169

205 231 233 242

254 TEAC 010 085 106 136

185 187 237 TECHNICS 101 113 128 134

147 218 TOSHIBA 137 THE 061 VICTOR 088 131 WARDS 089 YAMAHA 054 055 066 092

199

Brand Codes Brand Codes Brand Codes Brand Codes

90 Plasma TV

Troubleshooting Checklist

No output from one of

the speakers

• Adjust Balance in the AUDIO menu. (Refer to p.63)

Unusual sound from

inside the TV

• A change in ambient humidity or temperature may result in an unusual noise when the plasma display is turned on or off and does not indicate a fault with the TV.

No picture &

No sound

• Check whether the TV is turned on.

• Is the power cord inserted into wall power outlet?

• Test the wall power outlet, plug another product’s power cord into the outlet where the TV’s power cord was plugged in.

No or poor color

or poor picture

• Select Color in the Video menu and press the VOLUME (G) button. (Refer to p.61)

• Keep a sufficient distance between the TV and the VCR.

• Activate any function to restore the brightness of the picture.

(If still picture is on the screen for more than 5 minutes, the screen gets dark.)

The remote control

doesn’t work

• Check to see if there is any object between the TV and the remote control causing obstruction.

• Are batteries installed with correct polarity (+ to +, - to -)? (Refer to p.10)

• Correct remote operating mode set: TV, VCR etc.?

• Install new batteries. (Refer to p.10)

Picture OK &

No sound

• Press the VOLUME (G) button.

• Sound muted? Press MUTE button.

Picture appears slowly

after switching on

• This is normal, the image is muted during the TV startup process. Please contact your service center, if the picture has not appeared after five minutes.

Horizontal/vertical bars

or picture shaking

• Check for local interference such as an electrical appliance or power tool.

TTroubleshooting Checklist

roubleshooting Checklist

Owner’s Manual 91

91 Plasma TV

Maintenance

1. Here’s a great way to keep the dust off your screen for a while. Wet a soft cloth in a mixture of lukewarm water and a little fabric softener or dish washing detergent. Wring the cloth until it’s almost dry, and then use it to wipe the screen.

2. Make sure the excess water is off the screen, and then let it air-dry before you turn on your TV.

To remove dirt or dust, wipe the cabinet with a soft, dry, lint-free cloth. Please be sure not to use a wet cloth.

If you expect to leave your TV dormant for a long time (such as a vacation), it’s a good idea to unplug the power cord to protect against possible damage from lightning or power surges.

- Early malfunctions can be prevented. Careful and regular cleaning can extend the amount of time you will have your new TV. Be sure to turn the power off and unplug the power cord before you begin any cleaning.

Cleaning the Screen

Cleaning the Cabinet

Extended

Absence

Maintenance

92 Plasma TV

Specification

• The specifications shown above may be changed without prior notice for quality improvement.

Product Specifications

MODELS

AC100-240V ~ 60Hz

NTSC-M, ATSC

VHF 2 ~ 13, UHF 14 ~ 69, CATV 1 ~ 135, CADTV 1 ~ 135. DTV 2 ~ 69

75 Ω

16,770,000 (256 steps of each R, G and B)

32 ~ 104°F (0 ~ 40°C)

Less than 80%

6561 feet (2000m)

55.2 / 1402

31.4 / 798.5

11.9 / 302.5

122 / 55.3

1024 x 768 (Dot)

67.24 / 1708

36.6 / 931

12.6 / 320.7

189.2 / 85.8

1366 x 768 (Dot)

Width (inches / mm)

Height (inches / mm)

Depth (inches / mm)

Weight (pounds / kg)

Resolution

Power requirement

Television System

Program Coverage

External Antenna Impedance

Color

Operating Temperature Range

Operating Humidity Range

Maximum Elevation

DU-50PY10

DU-60PY10

Owner’s Manual 93

Notes

94 Plasma TV

Notes

Your LG Plasma TV will be repaired or replaced in accordance with the terms of this warranty, at LGE’s option, if it proves to be defective in material or workmanship under normal use, during the warranty period (“Warranty Period”) listed below, effective from the date (“Date of Purchase”) of original consumer purchase of the product. This warranty is good only to the original purchaser of the product and effective only when used in the United States, including Alaska, Hawaii, and U.S. Territories.

LG ELECTRONICS, INC.

PLASMA TV — U.S. LIMITED WARRANTY

CONCERNING PIXEL FUNCTIONALITY: Your Plasma TV contains about one million individual pixels. Plasma TV typically contain a small number of pixels that do not function normally. Your display has been inspected and is in compliance with manufacturer’s specifications, indicating that any pixel defects do not effect the operation or use of your display.

THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTY, EXPRESS OR IMPLIED, INCLUDING WITHOUT LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE EXPRESS WARRANTY PERIOD ABOVE. NEITHER THE MANUFACTURER NOR ITS U.S. DISTRIBUTOR SHALL BE LIABLE FOR ANY INCIDENTAL, CONSEQUENTIAL, INDIRECT, SPECIAL, OR PUNITIVE DAMAGES OF ANY NATURE, INCLUDING WITHOUT LIMITATION, LOST PROFITS, LOST OR CORRUPTED PROGRAMMING OR DATA, OR ANY OTHER DAMAGE WHETHER BASED IN CONTRACT, TORT, OR OTHERWISE. Some states do

not allow the exclusion or limitation of incidental or consequential damages or limitations on how long an implied warranty lasts, so the above exclusion or limitation may not apply to you. This warranty gives you specific legal rights and you may also have other rights that vary from state to state.

WARRANTY PERIOD:

LABOR and PARTS: 2 YEARS from the Date of Purchase.

Your unit will be repaired or replaced with a new, substitute model or factory reconditioned unit, at LGE’s option. If repaired, parts used in the repair may be new or remanufactured. Replacement Units and Repair Parts are warranted for the remaining portion of the original unit’s warranty period.

EFFECTIVE DATE OF WARRANTY: Your warranty period begins on the date of sale to the original consumer/end user. KEEP THE DEALER’S DATED BILL OF SALE OR PROOF OF DELIVERY as evidence of the purchase date. You will be required to submit a legible copy of your bill of sale or proof of delivery when requesting warranty service.

HOW SERVICE IS HANDLED:

In-Home Service: Please retain dealer’s

dated bill of sale or delivery ticket as evidence of the Date of Purchase for proof of warranty, and submit a copy of the bill of sale to the service person at the time warranty service is provided.

Please call 1-201-816-2000 to locate your nearest LGE Authorized Service Center.

Visit our website at:

http://www.lgservice.com

IMPORTANT: Please fill out and mail in your Product Registration Card or go to www.lgservice.com to register your

product online. This information will allow us to reach you promptly should we discover a safety or reliability problem that could affect you.

TO CONTACT THE LGE CUSTOMER SERVICE CENTER BY MAIL:

LGE Customer Interactive Center P.O. Box 240007 201 James Record Road Huntsville, Alabama 35824 http://www.lgservice.com

FOR SERVICE: Before you call for warranty service, check your operating guide – you may avoid a service call.

For warranty service information, please contact the LGE Customer Interactive Center telephone number.

When calling for service, please have your product model number, serial number and the date of pur-

chase or the date of original installation available.

If a replacement unit is required, under some circumstances you may be asked to provide a reserve deposit to the LGE Service Center against a credit card number as surety for advanced shipment. Your credit card will not be charged if you return the defective unit within 10 working days.

If a replacement unit is received, please use the carton and packaging from that unit in returning the defective unit to the LG

Brand Service Center.

Parts and service in accordance with the LGE warranty are LGE’s responsibility and will be provided without charge. Other service requirements will be at the owner’s expense. If you have problems in obtaining satisfactory warranty service, write or call the LGE Customer Interactive Center. Service may be provided by independently owned and operated service organizations.

To assure proper credit and avoid unnecessary charges, you must obtain an LGE Return Authorization before returning any product to the LGE Service Center. Contact the Customer Interactive Center for details.

CUSTOMER INTERACTIVE CENTER NUMBERS:

To obtain customer assistance, product information or Dealer or Service locations

Call 1-201-816-2000

24 hours a day, 365 days per year

THIS LIMITED WARRANTY DOES NOT APPLY TO:

The cost of repair or replacement under these excluded circumstances shall be borne by the consumer.

● damage caused in shipping or transit

● service required as a result of improper installation,

including incorrect or insufficient AC supply (please consult the owner’s manual for power supply requirements)

● installation or repair of antenna systems, cable con-

verters, cable company supplied equipment, or other components in a video system

● set-up or adjustment on consumer controls, or

damage caused by improper adjustments

● damage caused by other system components

● any panel that has been modified or incorporated

into any other product

● replacement of batteries on the remote control.

● damage (including cosmetic damage), failure, loss

or personal injury due to misuse, abuse, negli-

gence, improper maintenance or storage, or to acts of nature or other causes beyond our control. (Causes beyond our control include but are not limited to lightning strike, power surges, power outages and water damage.)

● image burn-in

● repair or replacement of warranted parts by other

than LGE authorized service centers.

● units purchased or serviced outside of the coverage

area.

● product where the original factory serial numbers

have been removed, defaced or changed in any way.

● product sold and labeled as “as is, where is” or sim-

ilar disclaimer.

P/NO : 3828VA0479F (3828VB0002L)

LG Electronics DU-50PY10 User Manual

Specifications and Main Features

Frequently Asked Questions

User Manual