LG DLEX2801L User Manual [en, es, fr]

Before beginning installation, read these

instructions carefully. This will simplify installation

and ensure that the dryer is installed correctly and

safely. Leave these instructions near the dryer

after installation for future reference.

Antes de comenzar la instalación, lea atentamente estas instrucciones. Esto simpliﬁcará la instalación

y asegurará que la secadora está instalada

en forma correcta y segura. Conserve estas

instrucciones cerca de la secadora luego de la

instalación para futuras consultas.

To contact LG Electronics, 24 hours a day, 7 days a week:

1-800-243-0000

Or visit us on the Web at: us.lge.com Número telefónico de LG Electronics, las 24

horas del día, 7 días a la semana:

1-800-243-0000

O visítenos en la Web en: us.lge.com To contact LG Electronics, 24 hours a day,

7 days a week :

1-888-LGCANADA

Or visit us on the Web at : ca.lge.com Pour contacter LG Electronics, 24 heures

Par jour, 7 jours par semaine :

1-888-LGCANADA

Ou visitez notre site Web a l’addresse : ca.lge.com

Avant de commencer à installer votre sécheuse, lisez

attentivement ces instructions. Cela simpliﬁera votre

installation et assurera que la sécheuse est installée

correctement et en toute sécurité. Conservez ces

instructions à proximité de la sécheuse après son

installation, pour référence future.

DLEX2801W DLEX2801R DLEX2801L

DLGX2802W DLGX2802R DLGX2802L

Protocol P154 Sanitization Performance of Residential

Clothes dryer

Ejecucion de Saneamiento en la zona residencial Secadoras Niveau de sanitisation des séche-linge

P/No. 3828EL3010T

résidentiels

IMPORTANT SAFETY INSTRUCTIONS

Basic Safety Precautions .......................................3

What to Do if You Smell Gas .................................. 4

California safe drinking water and toxic

enforcement act .................................................... 4

Grounding Instructions ...........................................5

Safety Instructions for Installation ...................... 5, 6

Safety Instructions for Steam Functions ................6

Safety Instructions for Connecting Electricity .......7

THANK YOU!

Congratulations on your purchase

and welcome to the LG family. Your

PARTS AND FEATURES

Special Features ..................................................... 8

Key Parts and Components ................................... 9

INSTALLATION INSTRUCTIONS

IMPORTANT: Read all installation instructions completely before installing and operating your

dryer! ................................................................... 10

Choose the Proper Location ................................ 10

Clearances ........................................................... 10

Installation With Optional

Pedestal Base or Stacking Kit .............................. 11

Optional Accessories ......................................... 11

Leveling the Dryer ................................................ 12

Reversing the Door Swing .................................... 12

Changing the Dryer Vent Location ....................... 13

Venting the Dryer ............................................ 14, 15

Connecting Gas Dryers .................................. 16, 17

Connecting Electric Dryers ............................. 18–22

Special Requirements for Manufactured

or Mobile Homes .................................................. 23

Final Installation Check .......................................23

Flow Check (Duct condition test) ......................... 24

HOW TO USE

Sorting Loads ....................................................... 25

Loading the Dryer ................................................. 25

Check the Lint Filter Before Every Load ............... 25

Control Panel Features ......................................... 26

Cycle Guide .......................................................... 27

The Display ........................................................... 28

Operating the Dryer .............................................. 29

Cycle Setting Buttons .......................................... 29

Cycle Option Buttons .......................................... 30

Special Functions ................................................. 31

Custom Program .................................................. 32

Steam Functions ............................................ 32–34

Steam Cycle Guide .............................................. 34

new LG Dryer combines the most

advanced drying sensor technology

with simple operation and high

efficiency. By following the

operating and care instructions

in this manual, your dryer will

provide you with many years of

reliable service.

OPTIONAL ACCESSORIES

Optional Accessories ........................................... 39

Pedestal Installation ....................................... 40, 41

Stacking Kit Installation .................................. 42, 43

Key Dimensions and Speciﬁ cations ..................... 43

WARRANTY ................................................... 44

USER MAINTENANCE INSTRUCTIONS

Regular Cleaning .................................................. 35

TROUBLESHOOTING

Before Calling for Service ............................... 36–38

READ ALL INSTRUCTIONS BEFORE USE wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

Your Safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word DANGER or WARNING. These words mean:

wDANGER: You can be killed or seriously injured if you don’t immediately follow instructions. wWARNING: You can be killed or seriously injured if you don’t follow instructions.

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

BASIC SAFETY PRECAUTIONS

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Read all instructions before using the dryer.

• Before use, the dryer must be properly installed as described in this manual.

• Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch ﬁre.

• Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other ﬂammable or explosive substances as they give off vapors that could ignite or explode.

• Do not reach into the dryer if the drum or any other part is moving.

• Do not repair or replace any part of the dryer or attempt any servicing unless speciﬁcally recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out.

• Do not tamper with controls.

• Before the dryer is removed from service or discarded, remove the door to the drying compartment.

• Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children.

• Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

• Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

• Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

• The interior of the dryer and exhaust vent should be cleaned periodically by qualiﬁed service personnel.

• Do not install or store the dryer where it will be exposed to the weather.

• Always check the inside of the dryer for foreign objects.

• Clean lint screen before or after each load.

READ ALL INSTRUCTIONS BEFORE USE wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁ re or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

• Do not store or use gasoline or other ﬂ ammable vapors and liquids in the vicinity of this appliance or any other appliances.

• Installation and service must be performed by a qualiﬁ ed installer, service agency, or the gas supplier.

WHAT TO DO IF YOU SMELL GAS:

1. Do not try to light a match or cigarette, or turn on any gas or electrical appliance.

2. Do not touch any electrical switches. Do not use any phone in your building.

3. Clear the room, building, or area of all occupants.

CALIFORNIA SAFE DRINKING WATER AND TOXIC ENFORCEMENT ACT

This act requires the governor of California to publish a list of substances known to the state to cause cancer, birth defects, or other reproductive harm and requires businesses to warn customers of potential exposure to such substances.

Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide, formaldehyde, and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.

4. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions carefully.

5. If you cannot reach your gas supplier, call the ﬁ re department.

Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be minimized further by properly venting the dryer to the outdoors.

READ ALL INSTRUCTIONS BEFORE USE

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance must be equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided with the appliance. If it will not ﬁt the outlet, have a proper outlet installed by a qualiﬁed electrician.

This appliance must be connected to a grounded metal, permanent wiring system or an equipmentgrounding conductor must be run with the circuit conductors and connected to the equipmentgrounding terminal or lead on the appliance.

Electrical shock can result if the dryer is not properly grounded.

wWARNING — Improper

connection of the equipment-grounding conductor can result in a risk of electric shock.

Check with a qualiﬁed electrician or service person if you are in doubt as to whether the appliance is properly grounded.

SAFETY INSTRUCTIONS FOR INSTALLATION

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Properly ground dryer to conform with all governing codes and ordinances. Follow details in the installation instructions. Electrical shock can result if the dryer is not properly grounded.

• Before use, the dryer must be properly

installed as described in this manual.

Electrical shock can result if the dryer is not properly grounded.

• Install and store the dryer where it will not be

exposed to temperatures below freezing or exposed to the weather.

• All repairs and servicing must be performed by an authorized servicer unless speciﬁcally recommended in this Owner’s Guide. Use only authorized factory parts. Failure to follow

this warning can cause serious injury, ﬁre, electrical shock, or death.

• To reduce the risk of electric shock, do not install the dryer in humid spaces. Failure to follow this warning can cause serious injury, ﬁre, electrical shock, or death.

•

Connect to a properly rated, protected, and sized power circuit to avoid electrical overload. Improper power circuit can melt,

creating electrical shock and/or ﬁre hazard.

• Remove all packing items and dispose of all shipping materials properly. Failure to do so can result in death, explosion, ﬁre, or burns.

• Place dryer at least 18 in. above the ﬂoor for a garage installation. Failure to do so can result in death, explosion, ﬁre, or burns.

• Keep all packaging from children. Packaging material can be dangerous for children. There is a risk of suffocation.

• Do not install nearby heat item. Such as stove, cooking oven. Failure to do so can cause deform, smoke and ﬁre.

• Do not place candle and cigarettes on top of the product. Failure to do so can cause deform, smoke and ﬁre.

• Remove all protective vinyl ﬁlm from the product. Failure to do so can cause deform, smoke and ﬁre.

READ ALL INSTRUCTIONS BEFORE USE

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁ re or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

SAFETY INSTRUCTIONS FOR INSTALLATION

Exhaust/Ducting:

• Gas dryers MUST be exhausted to the outside. Failure to follow these instructions

can result in ﬁ re or death.

• The dryer exhaust system must be exhausted

to the outside of the dwelling. If the dryer is not exhausted outdoors, some ﬁ ne lint and large amounts of moisture will be expelled into the laundry area. An accumulation of

lint in any area of the home can create a health and ﬁ re hazard.

• Use only rigid metal or ﬂ exible metal 4-in.

diameter ductwork inside the dryer cabinet or for exhausting to the outside. Use of plastic or other combustible ductwork can cause a ﬁ re. Punctured ductwork can cause

a ﬁ re if it collapses or becomes otherwise restricted in use or during installation.

• Ductwork is not provided with the dryer, and

you should obtain the necessary ductwork locally. The end cap should have hinged dampers to prevent backdraft when the dryer is not in use. Failure to follow these instructions

can result in ﬁ re or death.

• The exhaust duct must be 4 in. (10 cm) in

diameter with no obstructions. The exhaust duct should be kept as short as possible. Make sure to clean any old ducts before installing your new dryer. Failure to follow

these instructions can result in ﬁ re or death.

• Rigid or semi rigid metal ducting is

recommended for use between the dryer and the wall. In special installations when it is impossible to make a connection with the above recommendations, a ULlisted ﬂ exible metal transition duct may be used between the dryer and wall connection only. The use of this ducting will affect drying time. Failure to follow these instructions can

result in ﬁ re or death.

• DO NOT use sheet metal screws or other

fasteners which extend into the duct that could catch lint and reduce the efﬁ ciency of the exhaust system. Secure all joints with

duct tape. For complete details, follow the Installation Instructions. Failure to follow these instructions can result in ﬁ re or death.

SAFETY INSTRUCTIONS FOR STEAM FUNCTIONS

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Do not open the dryer door during steam cycles. Failure to follow these instructions can result in a burn hazard.

• Do not dry articles that have been previously

cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other ﬂ ammable or explosive substances as they give off vapors that could ignite or explode.

Failure to follow these instructions can result in ﬁ re or death.

• Do not ﬁ ll the steam feeder with gasoline, dry-cleaning solvents, or other ﬂ ammable or explosive substances. Failure to follow these

instructions can result in ﬁ re or death.

• Do not touch the steam nozzle in the drum during or after the steam cycle. Failure to follow these instructions can result in a burn hazard.

• Do not ﬁ ll the steam feeder with hot water (over 86°F/30°C). Failure to follow these instructions can result in a burn hazard.

READ ALL INSTRUCTIONS BEFORE USE

wWARNING For your safety, the information in this manual must be

followed to minimize the risk of ﬁre or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

SAFETY INSTRUCTIONS FOR CONNECTING ELECTRICITY

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Do not, under any circumstances, cut or

remove the ground prong from the power cord. To prevent personal injury or damage to

the dryer, the electrical power cord must be plugged into a properly grounded outlet.

• For personal safety, this dryer must be properly grounded. Failure to do so can result in electrical shock or injury.

• Refer to the installation instructions in this

manual for speciﬁc electrical requirements for your model. Failure to follow these

instructions can create an electrical shock hazard and/or a ﬁre hazard.

• This dryer must be plugged into a properly

grounded outlet. Electrical shock can result if the dryer is not properly grounded. Have the wall outlet and circuit checked by a qualiﬁed electrician to make sure the outlet is properly grounded. Failure to follow these instructions

can create an electrical shock hazard and/or a ﬁre hazard.

• The dryer should always be plugged into

its own individual electrical outlet which has a voltage rating that matches the rating plate. This provides the best performance

and also prevents overloading house wiring circuits which could cause a ﬁre hazard from overheated wires.

• Never unplug your dryer by pulling on the

power cord. Always grip plug ﬁrmly and pull straight out from the outlet. The power cord

can be damaged, resulting in a risk of ﬁre and electrical shock.

• Repair or replace immediately all power

cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. The power cord can melt,

creating electrical shock and/or ﬁre hazard.

• When installing or moving the dryer, be

careful not to pinch, crush, or damage the power cord. This will prevent injury and

prevent damage to the dryer from ﬁre and electrical shock.

SAVE THESE INSTRUCTIONS

SPECIAL FEATURES

EASY-TO-USE CONTROL PANEL

Rotate the Cycle Selector Knob to select the desired dry cycle. Add cycle options or adjust settings with the touch of a button.

EASY-ACCESS REVERSIBLE DOOR

Wide-opening door provides easy access for loading and unloading. Door swing can be reversed to adjust for installation location.

ULTRA-CAPACITY STAINLESS STEEL DRUM

WITH DRUM LIGHT

The ultra-large stainless steel drum offers superior durability. The drum is equipped with a yellow light that illuminates when the dryer door is open and turns off when the door is closed.

HELPFUL STEAM FUNCTIONS

LG’s new steam technology allows you to inject fabrics with a swirling jet of hot steam to refresh clothes, reduce static, and make ironing easier. Simply select the STEAMFRESH™ cycle, or you can add a Steam option to selected cycles.

FLOW SENSE™ DUCT BLOCKAGE SENSING SYSTEM INDICATOR

The FLOW SENSE™ duct blockage sensing system detects and alerts you to blockages in the ductwork that reduce exhaust flow from the dryer. This improve operating efficiency and help minimize service calls, saving you money.

KEY PARTS AND COMPONENTS

In addition to the special features and components outlined in the Special Features section, there are several other important components that are referenced in this manual.

FRONT-MOUNT LINT FILTER

Front-mounted lint filter allows for easy access and cleaning after every load.

LEVELING FEET

Four leveling feet (two in the front, and two in the back) adjust to improve dryer stability on uneven floors.

DRYING RACK

Use the drying rack with the RACK DRY cycle option. The drying rack allows items, such as sweaters, delicates, and gym shoes, to be placed in a flat position for drying.

Power Cord Location (Gas Models)

Gas Connection Location (Gas Models)

Terminal Block Access Panel (Electric Models)

Exhaust Duct Outlet

Rear of Dryer

Included Accessories

Drying Rack

(129.7mm)

(56.8 mm)

22.4

IMPORTANT: Read all installation instructions completely before installing and operating your dryer!

It is important that you review this entire manual before installing and using your dryer. Detailed instructions concerning electrical connections, gas connections, and exhaust requirements are provided on the following pages.

CHOOSE THE PROPER LOCATION

• Store and install the dryer where it will not be exposed to temperatures below freezing or exposed to outdoor weather conditions.

• Choose a location with a solid, level ﬂ oor.

• If the dryer is being installed in a garage, place the dryer at least 18 in. (46 cm) above the ﬂ oor.

CLEARANCES

• Properly ground dryer to conform with all governing codes and ordinances.

• To reduce the risk of electric shock, do not install the dryer in damp or wet locations.

• If you are installing your dryer in a manufactured or mobile home, please refer to the section

Special Requirements for Manufactured or Mobile Homes.

Closet Door Vent Requirements

• Most installations require a minimum 5½ in. (14 cm) clearance behind the dryer for the exhaust ducting.

• Allow minimum clearances of at least 1 in. (2.5 cm) on the sides and back to minimize vibration and noise.

• Allowing additional clearance for installation and servicing is recommended.

• Be sure to allow for wall, door, or ﬂ oor moldings that may increase the required clearances.

• Allow at least 24 in. (61 cm) in front of the dryer to open the door.

Additional Instructions for closet installations:

• The closet door must allow for sufﬁ cient airﬂ ow. Refer to the diagram above for minimum vent opening requirements. A louvered door is also acceptable.

• Make sure that there is at least 18 in. (46 cm) of clearance above the dryer.

INSTALLATION WITH OPTIONAL PEDESTAL BASE OR STACKING KIT

IMPORTANT: If you are installing your dryer using an optional pedestal base or stacking kit, please refer to Optional Accessories in this manual or to the instructions for your pedestal

or stacking kit before proceeding with the installation.

Required Dimensions for Installation

With Pedestal

Required Dimensions for Installation

With Stacking Kit

OPTIONAL ACCESSORIES

For these and other LG products, contact your local LG dealer, or visit our Web site at us.lge.com.

Pedestal (sold separately)

Stacking Kit (sold separately)

LEVELING THE DRYER

WARNING

• Wear gloves during installation.

• Failure to follow these instructions can result in injury.

To ensure that the dryer provides optimal drying performance, it must be level. To minimize vibration, noise, and unwanted movement, the floor must be a perfectly level, solid surface.

NOTE: Adjust the leveling feet only as far as necessary to level the dryer. Extending the leveling feet more than necessary can cause the dryer to vibrate.

Level

Leveling Feet

Position the dryer in the final location. Place a level across the top of the dryer.

• All four leveling feet must rest solidly on the floor. Gently push on the top corners of the dryer to make sure that the dryer does not rock from corner to corner.

If you are installing the dryer on the optional pedestal, you must use the leveling feet on the pedestal to level the dryer. The dryer leveling feet should be fully retracted.

Use an adjustable wrench to turn the leveling feet. Turn clockwise to raise the dryer or counterclockwise to lower it. Raise or lower the leveling feet until dryer is level from side to side and front to back.

Make sure that all 4 leveling feet are in firm contact with the floor.

REVERSING THE DOOR SWING

The swing of the dryer door can be reversed to fit your installation location.

Door Latch

Hinge

Latch Screws

Open the dryer door. Using a Phillips

1 2

screwdriver, remove the 4 screws that secure the door hinge to the dryer door opening. Remove the 6 screws from the latch side of the dryer door opening, and remove the door latch.

Screws

Turn the door around so the hinge is reversed, and reattach the door using the 4 screws previously removed. Reinstall the door latch and the 6 screws.

Test the door swing to make sure the door moves freely and latches securely.

Latch Screws

Hinge Screws

CHANGING THE DRYER VENT LOCATION

11/2"

(3.8 cm)

WARNING

• Use a heavy metal vent.

• Do not use plastic or thin foil duct.

• Clean old ducts before installing this dryer.

• Wear gloves during installation.

• Failure to follow these instructions can result in death or ﬁre.

Your new dryer is shipped to vent to the rear. It can also be configured to vent to the bottom or side (right-side venting is not available on gas models).

An adapter kit, part number 383EEL9001B, may be purchased from your LG retailer. This kit contains the necessary duct components to change the dryer vent location.

OPTION 1: Side Venting

Adapter Duct

Rear Exhaust Duct

Remove the rear exhaust duct retaining

screw. Pull out the exhaust duct.

OPTION 2: Bottom Venting

Adapter Duct

Retaining Screw

Bracket

Knockout

Press the tabs on the knockout and carefully remove the knockout for the desired vent opening (right-side venting is not available on gas models). Press the adapter duct onto the blower housing and secure to the base of the dryer as shown.

Cover Plate

Elbow

Preassemble a 4-in. (10 cm) elbow to the next 4-in. (10 cm) duct section, and secure all joints with duct tape. Be sure that the male end of the elbow faces AWAY from the dryer. Insert the elbow/duct assembly through the side opening and press it onto the adapter duct. Secure in place with duct tape.

Be sure that the male end of the duct protrudes 1½ in. (3.8 cm) to connect the remaining ductwork. Attach cover plate to the back of the dryer with included screw.

Bracket

Press the adapter duct onto the blower housing and secure to the base of the dryer as shown.

Cover Plate

Elbow

Insert the 4-in. (10 cm) elbow through the rear opening and press it onto the adapter duct. Be sure that the male end of the elbow faces down through hole in the bottom of the dryer. Secure in place with duct tape.

Attach the cover plate to the back of the dryer with included screw.

VENTING THE DRYER

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Do not crush or collapse ductwork. Failure

to follow these instructions can result in ﬁ re or death.

• Do not allow ductwork to rest on or contact sharp objects. Failure to follow these instructions can result in ﬁ re or death.

• If connecting to existing ductwork, make

sure it is suitable and clean before installing the dryer. Failure to follow these instructions

can result in ﬁ re or death.

• Venting must conform to local building codes. Failure to follow these instructions can result in ﬁ re or death.

• Gas dryers MUST exhaust to the outdoors. Failure to follow these instructions can result in ﬁ re or death.

• Use only 4-in. (10 cm) rigid or ﬂ exible metal

ductwork inside the dryer cabinet and for venting outside. Failure to follow these

instructions can result in ﬁ re or death.

• To reduce the risk of ﬁ re, combustion, or

accumulation of combustible gases, DO NOT exhaust dryer air into an enclosed and unventilated area, such as an attic, wall, ceiling, crawl space, chimney, gas vent, or concealed space of a building. Failure to

follow these instructions can result in ﬁ re or death.

• To reduce the risk of ﬁ re, DO NOT exhaust the dryer with plastic or thin foil ducting. Failure to follow these instructions can result in ﬁ re or death.

• The exhaust duct must be 4 in. (10 cm) in

diameter with no obstructions. The exhaust duct should be kept as short as possible. Make sure to clean any old ducts before installing your new dryer. Failure to follow

these instructions can result in ﬁ re or death.

• Rigid or semirigid metal ducting is

recommended for use between the dryer and the wall. In special installations when it is impossible to make a connection with the above recommendations, a UL-listed ﬂ exible metal transition duct may be used between the dryer and wall connection only. The use of this ducting will affect drying time. Failure to follow these instructions can

result in ﬁ re or death.

• DO NOT use sheet metal screws or other

fasteners which extend into the duct that could catch lint and reduce the efﬁ ciency of the exhaust system. Secure all joints with duct tape. Failure to follow these

instructions can result in ﬁ re or death.

• To maximize operating results, please

observe the duct length limitations noted in the chart on page 15. Failure to follow these

instructions can result in ﬁ re or death.

• Ductwork is not provided with the dryer.

You should obtain the necessary ductwork locally. The end cap should have hinged dampers to prevent backdraft when the dryer is not in use. Failure to follow these

instructions can result in ﬁ re or death.

VENTING THE DRYER (cont.)

(10.2 cm)

21/2"

(6.35 cm)

(10.2 cm)

Ductwork

Number of Max. Length of 4-In. Dia. Max. Length of 4-In. Dia. Wall Cap Type 90° Elbows Rigid Metal Duct Flexible Metal Duct

0 65 ft. (19.8 m) 45 ft. (13.7 m)

Recommended

1 55 ft. (16.8 m) 35 ft. (10.7 m) 2 47 ft. (13.7 m) 30 ft. (9.1 m) 3 36 ft. (11.0 m) 25 ft. (7.6 m) 4 28 ft. (8.5 m) 20 ft. (6.1 m) 0 55 ft. (16.8 m) 35 ft. (10.7 m)

Use Only for Short

2 41 ft. (12.5 m) 21 ft. (6.4 m) 3 30 ft. (9.1 m) 17 ft. (5.2 m) 4 22 ft. (6.7 m) 15 ft. (4.5 m)

NOTE: Deduct 6 ft. (1.8 m) for each additional elbow. It is not recommended to use more than four 90° elbows.

Run Installations

1 47 ft. (13.7 m) 27 ft. (8.1 m)

Routing and Connecting Ductwork

Follow the guidelines below to maximize drying performance and reduce lint buildup and condensation in the ductwork.

NOTE: Ductwork and fittings are NOT included and must be purchased separately.

• Use 4-in. (10 cm) diameter rigid or semirigid metal ductwork.

• The exhaust duct run should be as short as possible.

• Use as few elbow joints as possible.

• The male end of each section of exhaust duct must point away from the dryer.

• Use duct tape on all duct joints.

• Insulate ductwork that runs through unheated areas in order to reduce condensation and lint buildup on duct surfaces.

IMPORTANT: Failure to exhaust the dryer correctly will void the dryer’s warranty.

Correct Venting

Incorrect Venting

CONNECTING GAS DRYERS

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Gas supply requirements:

As shipped from the factory, this dryer is conﬁ gured for use with natural gas. It can be converted for use with LP (Liqueﬁ ed Propane) gas. Gas pressure must not exceed 13 in. water column.

• A qualiﬁ ed service or gas company technician must connect the dryer to the gas service.

Failure to do so can result in ﬁ re, explosion, or death.

• Isolate the dryer from the gas supply system

by closing its individual manual shutoff valve during any pressure testing of the gas supply.

Failure to do so can result in ﬁ re, explosion, or death.

• Supply line requirements:

Your laundry room must have a rigid gas supply line to your dryer. In the United States, an individual manual shutoff valve MUST be installed within at least 6 ft. (1.8 m) of the dryer, in accordance with the National Fuel Gas Code ANSI Z223.1 or Canadian gas installation code CSA B149.1. A 1/8-in. NPT pipe plug must be installed. Failure to do so can result in ﬁ re,

explosion, or death.

• If using a rigid pipe, the rigid pipe should be

1/2-in. IPS. If acceptable under local codes and ordinances and when acceptable to your gas supplier, 3/8-in. approved tubing may be used where lengths are less than 20 ft. (6.1 m). Larger tubing should be used for lengths in excess of 20 ft. (6.1 m). Failure to do so can

result in ﬁ re, explosion, or death.

• Connect the dryer to the type of gas shown on the nameplate. Failure to do so can result in ﬁ re, explosion, or death.

• To prevent contamination of the gas valve,

purge the gas supply of air and sediment before connecting the gas supply to the dryer. Before tightening the connection between the gas supply and the dryer, purge remaining air until the odor of gas is detected. Failure to do

so can result in ﬁ re, explosion, or death.

• DO NOT use an open ﬂ ame to inspect for gas

leaks. Use a noncorrosive leak-detection ﬂ uid.

Failure to do so can result in ﬁ re, explosion, or death.

• Use only a new AGA- or CSA-certiﬁ ed gas

supply line with ﬂ exible stainless steel connectors. Failure to do so can result in ﬁ re,

explosion, or death.

• Securely tighten all gas connections. Failure to do so can result in ﬁ re, explosion, or death.

• Use Teﬂ on® tape or a pipe-joint compound that

is insoluble in Liqueﬁ ed Petroleum (LP) gas on all pipe threads. Failure to do so can result in ﬁ re,

explosion, or death.

• DO NOT attempt any disassembly of the dryer;

any disassembly requires the attention and tools of an authorized and qualiﬁ ed service person or company. Failure to do so can result

in ﬁ re, explosion, or death.

Electrical Requirements for Gas Models Only

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Do not, under any circumstances, cut or

remove the third (ground) prong from the power cord. Failure to follow this warning can result in

ﬁ re, explosion, or death.

• For personal safety, this dryer must be properly grounded. Failure to follow this warning can result in ﬁ re, explosion, or death.

• The power cord of this dryer is equipped with

a 3-prong (grounding) plug which mates with a standard 3-prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance. Failure to follow this

warning can result in ﬁ re, explosion, or death.

• This dryer must be plugged into a

120-VAC, 60-Hz. grounded outlet protected by a 15-ampere fuse or circuit breaker. Failure to

follow this warning can result in ﬁ re, explosion, or death.

• Where a standard 2-prong wall outlet is

encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall outlet. Failure

to follow this warning can result in ﬁ re, explosion, or death.

CONNECTING GAS DRYERS (cont.)

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Installation and service must be performed

by a qualiﬁed installer, service agency, or the gas supplier. Failure to do so can result in ﬁre,

explosion, or death.

• Use only a new stainless steel ﬂexible

connector and a new AGA-certiﬁed connector. Failure to do so can result in ﬁre,

explosion, or death.

• A gas shutoff valve must be installed within 6 ft. (1.8 m) of the dryer. Failure to do so can result in ﬁre, explosion, or death.

• The dryer is conﬁgured for Natural Gas when

shipped from the factory. Make sure that the dryer is equipped with the correct burner nozzle for the type of gas being used (Natural Gas or Liqueﬁed Petroleum). Failure to do so

can result in ﬁre, explosion, or death.

• If necessary, the correct nozzle (for the LP

nozzle kit order part number 4948EL4002B) should be installed by a qualiﬁed technician and the change should be noted on the dryer.

Failure to do so can result in ﬁre, explosion, or death.

• All connections must be in accordance with local codes and regulations. Failure to do so can result in ﬁre, explosion, or death.

• Gas dryers MUST exhaust to the outdoors. Failure to do so can result in ﬁre, explosion, or death.

Connecting the Gas Supply

Make sure that the gas supply to the laundry

room is turned OFF. Confirm that the type of gas available in your laundry room is appropriate for the dryer. The dryer is prepared for Natural Gas with a 3/8-in. NPT gas connection.

Remove the shipping cap from the gas

connection at the back of the dryer. Be careful not to damage the threads of the gas connector when removing the shipping cap.

Connect the dryer to your laundry room’s gas

supply using a new flexible stainless steel connector with a 3/8-in. NPT fitting.

Securely tighten all connections between the

dryer and your laundry room’s gas supply. Turn on your laundry room’s gas supply and check all pipe connections (both internal and external) for gas leaks with a noncorrosive leak-detection fluid.

Electrical Connection

Plug dryer into a

120-VAC, 60-Hz.

grounded 3-prong outlet.

1/8" NPT Pipe

3/8" NPT Gas Connection

AGA/CSA-Certified Stainless Steel Flexible Connector

Plug Gas Supply

Shutoff Valve

High-Altitude Installations

The BTU rating of this dryer is AGA-certified for elevations below 10,000 feet.

If your gas dryer is being installed at an elevation above 10,000 feet, it must be derated by a qualified technician or gas supplier.

CONNECTING ELECTRIC DRYERS

wWARNING: To help prevent fire, electric shock, serious injury, or death, the wiring and

grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all applicable local regulations. Please contact a qualified electrician to check your home’s wiring and fuses to ensure that your home has adequate electrical power to operate the dryer.

Electrical Requirements for Electric Models Only

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• This dryer must be connected to a grounded

metal, permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the dryer. Failure to do

so can result in ﬁ re, explosion, or death.

• The dryer has its own terminal block that

must be connected to a separate 240 VAC, 60-Hertz, single-phase circuit, fused at 30 amperes (the circuit must be fused on both sides of the line). ELECTRICAL SERVICE FOR THE DRYER SHOULD BE OF THE MAXIMUM RATE VOLTAGE LISTED ON THE NAMEPLATE. DO NOT CONNECT DRYER TO 110-, 115-, OR 120-VOLT CIRCUIT. Heating elements are available for ﬁ eld installation in dryers which are to be connected to an electrical service of a different voltage than that listed on the rating plate. Failure to follow

these instructions can result in ﬁ re, explosion, or death.

• If branch circuit to dryer is 15 ft. (4.5 m)

or less in length, use UL (Underwriters Laboratories) listed No.-10 AWG wire (copper wire only), or as required by local codes. If over 15 ft. (4.50 m), use UL-listed No.-8 AWG wire (copper wire only), or as required by local codes. Allow sufﬁ cient slack in wiring so dryer can be moved from its normal location when necessary. Failure

to do so can result in ﬁ re, explosion, or death.

• The power cord (pigtail) connection between

wall receptacle and dryer terminal block IS NOT supplied with dryer. Type of pigtail and gauge of wire must conform to local codes and with instructions on the following pages. Failure to follow these instructions can

result in ﬁ re, explosion, or death.

• A 4-wire connection is required for all mobile

and manufactured home installations, as well as all new construction after January 1, 1996. A 4-wire connection must be used where local codes do not permit grounding through the neutral wire. Failure to do so can

result in ﬁ re, explosion, or death.

wWARNING:

appliance, follow basic precautions, including the following:

• Do not modify the plug and internal wire provided with the dryer.

• The dryer should be connected to 4-hole outlet.

To reduce the risk of fire, electric shock, or injury to persons when using this

• If it does not ﬁ t the outlet, a proper outlet will need to be installed by a qualiﬁ ed electrician.

Special Electrical Requirements for Mobile or Manufactured Homes

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Any installation in a manufactured or mobile home must comply with the Manufactured Home Construction and Safety Standards Title 24 CFR, Part 32-80 or Standard CAN/ CSA0Z240 MH and local codes and ordinances.

• A 4-wire connection is required for all mobile

and manufactured home installations, as well as all new construction after January 1, 1996.

Failure to do so can result in ﬁ re, explosion, or death.

CONNECTING ELECTRIC DRYERS (cont.)

USA ONLY

wWARNING:

• Connect the power cord to the terminal block. Each colored wire should be connected to same color screw. Wire color indicated on manual is connected to the same color screw in block. Failure to follow these instructions may result in a short or overload.

Grounding through the neutral conductor is prohibited for: (1) new branch-circuit

• installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor.

Four-Wire Connection for Electric Dryers: Power Cord

• A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.

• A UL-listed strain relief is required.

Terminal Block

UL-Listed Strain Relief

UL-Listed 4-Wire Power Cord

Remove the terminal block access cover on the upper back of the dryer. Install a UL-listed strain relief into the power cord through-hole; then thread a UL-listed, 30A,

240V, 4-wire, #10 AWG-minimum copper

conductor power cord through the strain relief.

• Use a 30-amp, 240V, UL-listed power cord with #10 AWG-minimum copper conductor and closed loop or forked terminals with upturned ends.

Hot (Black)

Ground Screw

Power Cord Ground Wire

Transfer the dryer’s ground wire from behind

Neutral (White)

Hot (Red)

the green ground screw to the center screw of the terminal block. Attach the two hot leads of the power cord to the outer terminal block screws. Attach the white neutral wire to the center terminal block screw. Attach the power cord ground wire to the green ground screw. TIGHTEN ALL SCREWS SECURELY. Reinstall the terminal block access cover.

CONNECTING ELECTRIC DRYERS (cont.)

USA ONLY

wWARNING:

• Grounding through the neutral conductor is prohibited for: (1) new branch-circuit installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor.

Four-Wire Connection for Electric Dryers: Direct Wire

• A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.

• A UL-listed strain relief is required.

1" (2.5 cm)

Ground Wire

• Use UL-listed 4-wire #10 AWG-minimum copper conductor cable.

• Allow at least 5 ft (1.5 m) length to allow for removal and reinstallation of the dryer.

Terminal Block

UL-Listed Strain Relief

(12.7 cm)

Remove 5 inches (12.7 cm) of the outer covering from the wire. Remove 5 inches of insulation from the ground wire. Cut off approximately 11⁄2 inches (3.8 cm) from the other three wires and strip 1 inch (2.5 cm) insulation from each wire. Bend the ends of the three shorter wires into a hook shape.

Hot (Black)

Ground Screw

Ground Wire

Transfer the dryer’s ground wire from behind

Neutral (White)

Hot (Red)

the green ground screw to the center screw of the terminal block. Attach the two hot leads of the power cable to the outer terminal block screws. Attach the white neutral wire to the center terminal block screw. Attach the power cable ground wire to the green ground screw. TIGHTEN ALL SCREWS SECURELY. Reinstall the terminal block access cover.

UL-Listed 4-Wire Power Cord

Remove the terminal block access cover on the upper back of the dryer. Install a UL-listed strain relief into the power cord through-hole; then thread the power cable prepared in Step 1 through the strain relief.

CONNECTING ELECTRIC DRYERS (cont.)

USA ONLY

wWARNING:

Grounding through the neutral conductor is prohibited for: (1) new branch-circuit

• installations, (2) mobile homes, (3) recreational vehicles, and (4) areas where local codes prohibit grounding through the neutral conductor.

Three-Wire Connection for Electric Dryers: Power Cord

• A 3-wire connection is NOT permitted on new construction after January 1, 1996.

• A UL-listed strain relief is required.

Terminal Block

UL-Listed Strain Relief

UL-Listed 3-Wire Power Cord

Remove the terminal block access cover on the upper back of the dryer. Install a UL-listed strain relief into the power cord through-hole; then thread a UL-listed, 30A,

240V, 3-wire, #10 AWG-minimum copper

conductor power cord through the strain relief.

• Use a 30-amp, 240V, UL-listed power cord with #10 AWG-minimum copper conductor and closed loop or forked terminal s with upturned ends.

Hot (Black)

Ground Screw

Ground Wire

Attach the two hot leads of the power cord

Neutral (White)

Hot (Red)

to the outer terminal block screws. Attach the neutral wire to the center terminal block screw. Connect the external ground (if required by local codes) to the green ground screw. TIGHTEN ALL SCREWS SECURELY. Reinstall the terminal block access cover.

CONNECTING ELECTRIC DRYERS (cont.)

USA ONLY

wWARNING:

Three-Wire Connection for Electric Dryers: Direct Wire

• A 3-wire connection is NOT permitted on new construction after January 1, 1996.

• A UL-listed strain relief is required.

1" (2.5 cm)

Remove 31⁄2 inches (8.9 cm) of the outer covering from the wire. Strip 1 inch (2.5 cm) insulation from each wire. Bend the ends of the three wires into a hook shape.

Hot Black)

Neutral (White)

Hot (Red)

• Use UL-listed 3-wire #10 AWG-minimum copper conductor cable.

• Allow at least 5 ft (1.5 m) length to allow for removal and reinstallation of the dryer.

Terminal Block

UL-Listed Strain Relief

UL-Listed 3-Wire Power Cord

Ground Screw

Ground Wire

Attach the two hot leads of the power cord to the outer terminal block screws. Attach the neutral wire to the center terminal block screw. Connect the external ground (if required by local codes) to the green ground screw. TIGHTEN ALL SCREWS SECURELY. Reinstall the terminal block access cover.

SPECIAL REQUIREMENTS FOR MANUFACTURED OR MOBILE HOMES

Any installation in a manufactured or mobile home must comply with the Manufactured Home Construction and Safety Standards Title 24 CFR, Part 32-80 or Standard CAN/CSA0Z240 MH and local codes and ordinances. If you are uncertain whether your proposed installation will comply with these standards, please contact a service and installation professional for assistance.

• A gas dryer must be permanently attached to the ﬂoor.

• The electrical connection for an electric dryer must be a 4-wire connection. More detailed information concerning the electrical connection is provided in the section Connecting Electric Dryers.

• To reduce the risk of combustion and ﬁre, the dryer must be vented to the outside.

• DO NOT vent the dryer under a manufactured home or mobile home.

• Electric dryers may be vented to the outside using the back, left, right, or bottom panel.

• Gas dryers may be vented to the outside using the back, left, or bottom panel. Gas dryers may not be vented to the outside using the right side panel because of the burner housing.

• The dryer exhaust duct must be afﬁxed securely to the manufactured or mobile home structure, and the exhaust duct must be made of a material that will resist ﬁre and combustion. It is recommended that you use a rigid or ﬂexible metal duct.

• DO NOT connect the dryer exhaust duct to any other duct, vent, chimney, or other exhaust duct.

• Make sure the dryer has adequate access to outside fresh air to ensure proper operation. The opening for outside fresh air must be at least 25 in2 (163 cm2).

• It is important that the clearance of the duct from any combustible construction be at least 2 in. (5 cm), and when venting the dryer to the outdoors, the dryer can be installed with a clearance of 1 in. (2.5 cm) at the sides and back of the dryer.

• Please be aware that venting materials are not supplied with the dryer. You should obtain the venting materials necessary for proper installation.

FINAL INSTALLATION CHECK

Once you have completed the installation of the dryer and it is in its final location, confirm proper operation with the following tests and Duct Condition Testing on the following page.

Testing Dryer Heating

GAS MODELS

Close the dryer door, press the ON/OFF switch to turn the dryer on, and start the dryer on a heat setting. When the dryer starts, the igniter should ignite the main burner.

NOTE: If all air is not purged from the gas line, the gas igniter may turn off before the main burner ignites. If this happens, the igniter will reattempt gas ignition after approximately two minutes.

ELECTRIC MODELS

Close the dryer door, press the ON/OFF switch to turn the dryer on, and start the dryer on a heat setting. The exhaust air should be warm after the dryer has been operating for 3 minutes.

Checking Airflow

Effective dryer operation requires proper airflow. The adequacy of the airflow can be measured by evaluating the static pressure. Static pressure in the exhaust duct can be measured with a manometer, placed on the exhaust duct approximately 2 ft. (60.9 cm) from the dryer. Static pressure in the exhaust duct should not exceed 0.6 in. (1.5 cm). The dryer should be checked while the dryer is running with no load.

Checking Levelness

Once the dryer is in its final location, recheck the dryer to be sure it is level. Make sure it is level front to back and side to side, and that all 4 leveling feet are firmly on the floor.

FLOW CHECK (DUCT CONDITION TEST)

Your dryer features FlowSense sensing system that automatically detects blockages and restrictions in dryer ductwork. Keeping ductwork clean of lint buildup and free of restrictions allows clothes to dry faster and reduces energy use.

NOTE: When the dryer is first installed, this test should be performed to alert you to any existing problems with the exhaust duct in your home. However, since the test performed during normal operation provides more accurate information on the condition of the exhaust duct than does the installation test, the number of bars displayed during the two tests may not be the same.

, an innovative

To activate the ﬂ ow check (Duct condition test) :

NOTE: Dryer heating test must be performed before

proceeding. Then perform the duct condition test below:

Press and hold the DAMP DRY BEEP and

TEMP. CONTROL buttons at the same time. While holding these buttons, press POWER ON/OFF.

Correct Venting

Restricted or Blocked Airflow

Avoid long runs or runs with multiple elbows or bends.

The dryer will show lnS in the number display to indicate that it is in duct condition testing mode.

IMPORTANT: Do NOT interrrupt the test cycle!

Press START/PAUSE. The dryer will run for approximately 2 minutes to test for blockages or restrictions to air ﬂ ow in the ductwork.

If “YES” is shown in the display, the ductwork is free from blockages or restrictions.

If “no” is shown in the display, the dryer ductwork has a blockage that needs to be removed

immediately.

Check for blockages and lint buildup.

Make sure the ductwork is not crushed or restricted.

Tumble dry

Dry

Normal

Permanent Press

wrinkle resistant

Gentle/

delicate

Do not tumble dry

Do not dry (used with

do not wash)

Heat setting

High

Medium

Low

No heat/air

Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for more detailed information. Important Warning: To reduce the risk of fire, electric shock,

or injury to persons, read this entire manual, including the Important Safety Instructions, before operating this dryer.

SORTING LOADS

Fabric Care Labels

Most articles of clothing feature fabric care labels that include instructions for proper care.

Grouping Similar Items

For best results, sort clothes into loads that can be dried with the same drying cycle.

Different fabrics have different care requirements, and some fabrics will dry more quickly than others.

LOADING THE DRYER

wWARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Check all pockets to make sure that they are

empty. Items such as clips, pens, coins, and keys can damage both your dryer and your clothes. Flammable objects such as lighters or matches could ignite, causing a ﬁre.

Failure to do so can result in ﬁre, explosion, or death.

• Never dry clothes that have been exposed to

oil, gasoline, or other ﬂammable substances. Washing clothes will not completely remove oil residues. Failure to obey this warning can

result in ﬁre, explosion, or death.

• Combine large and small items in a load.

• Damp clothes will expand as they dry. Do not overload the dryer; clothes require room to tumble dry properly.

• Close zippers, hooks, and drawstrings to prevent these items from snagging or tangling on other clothes.

CHECK THE LINT FILTER BEFORE EVERY LOAD

Always make sure the lint filter is clean before starting a new load; a clogged lint filter will increase drying times.

To clean, pull the lint filter straight up and roll any lint off the filter with your fingers. Do not rinse or wash the filter to remove lint. Push the lint filter firmly back into place. See “Care and Cleaning” for more information.

Always ensure the lint filter is properly installed before running the dryer. Running the dryer with a loose or missing lint filter may damage the dryer and articles in the dryer.

Lint Filter

CONTROL PANEL FEATURES

Following are instructions for starting and using your new dryer. Please refer to specific sections of this manual for more detailed information. Important Warning: To reduce the risk of fire,

electric shock, or injury to persons, read this entire manual, including the Important Safety Instructions, before operating this dryer.

POWER ON/OFF BUTTON

Press to turn the dryer ON. Press again to turn the dryer OFF.

NOTE: Pressing the ON/OFF button during a cycle will cancel that cycle and any load settings will be lost.

CYCLE SELECTOR KNOB

Turn this knob to select the desired cycle. Once the desired cycle has been selected, the standard presets will be shown in the display. On MANUAL DRY cycles, these settings can be adjusted using the cycle settings buttons anytime before starting the cycle.

START/PAUSE BUTTON

Press this button to START the selected cycle. If the dryer is running, use this button to PAUSE the cycle without losing the current settings.

NOTE: If you do not press the START/PAUSE button to resume a cycle within 4 minutes, the dryer automatically turns off.

MORE TIME/LESS TIME BUTTONS

To adjust the drying time, use these buttons with MANUAL DRY, TIME DRY, and STEAMFRESH™ cycles, as well as the REDUCE STATIC and EASY IRON options. Press the MORE TIME button to increase the selected manual cycle time by a minute; press LESS TIME to decrease the cycle time by a minute.

CYCLE SETTING BUTTONS

Use these buttons to select the desired cycle settings for the selected cycle. The current settings are shown in the display. Press the button for that option to view and select other settings.

TIME AND STATUS DISPLAY

The display shows the settings, estimated time remaining, options, and status messages for your dryer.

OPTION BUTTONS

The OPTION buttons allow you to select additional cycle options. Certain buttons feature a special function (see the following pages for details) that can be activated by pressing and holding that option button.

HELPFUL STEAM FUNCTIONS

For detailed information about the individual options, please see the following pages.

CYCLE GUIDE

The cycle guide below shows the options and recommended fabric types for each cycle.

Type

Cycle

STEAM

FRESH

STEAM SANITARY

HEAVY DUTY

COTTON/ TOWELS

NORMAL

PERM. PRESS

DELICATES

SPEED DRY

AIR DRY

TIME DRY

RACK DRY

Fabric Type

Comforter, Shirts, Trousers

(

except

especially delicate fabrics)

Comforter, Bedding, children’s clothing

Jeans, heavyweight items

Denims, towels, heavy cottons

Work clothes, corduroys, etc.

Permanent press, synthetic items

Lingerie, sheets, blouses

For small loads with short drying times

For irems that require heat-free drying such as plastics or rubber

For general drying; time, temperature, and options can be set manually

Wool sweaters, silk, lingerie

Dry

Level

Off

Normal

Adjustable

Normal

Adjustable

Normal

Adjustable

Normal

Adjustable

Normal

Adjustable

Off

Temperature

MID HIGH

HIGH

MID HIGH

MEDIUM

LOW

HIGH

Adjustable

No Heat

HIGH

Adjustable

Off

ULTRA LOW

LOW

Time

in Min.

Adjustable

More Time/

Less Time

Wrinkle

Care

Anti-

Bacterial

Damp

Dry

Reduce

Static

Easy

Iron

Sensor Dry Cycles

Sensor Dry cycles utilize LG’s unique dual sensor system to detect and compare the moisture level in clothes and in the air and adjust the drying time as needed to ensure superior results. The dryer automatically sets the dryness level and temperature at the recommended setting for each cycle. The estimated time remaining will

Manual Dry Cycles

Use Manual Dry cycles to select a specific amount of drying time and a drying temperature. When a Manual Dry cycle is selected, the ESTIMATED TIME REMAINING display shows the actual time remaining in your cycle. You can change the actual time in the cycle by pressing MORE TIME or LESS TIME.

be shown in the display. NOTE: To protect your garments, not every dry level, temperature, or option is available

with every cycle.

THE DISPLAY

The display shows the settings, estimated time remaining, options, and status messages for your dryer. When the dryer is turned on, the light in the display will illuminate.

ESTIMATED TIME REMAINING

When the START/PAUSE button is pressed, the dryer will display the estimated (SENSOR DRY) or set time (TIME DRY) remaining, and begin tumbling.

NOTE: The cycle time on SENSOR DRY cycles may fluctuate as the dryer recalculates drying time for optimal results.

CYCLE COMPLETION INDICATOR WITH CHECK FILTER REMINDER

This portion of the display shows which stage of the drying cycle is currently underway (CHECK FILTER, DRYING, COOLING, or WRINKLE CARE).

CHILD LOCK INDICATOR

When CHILD LOCK is set, the Child Lock indicator will appear and all buttons are disabled except the ON/OFF button. This prevents children from changing settings while the dryer is operating.

7 5

CHECK FILTER REMINDER

The display will show CHECK FILTER when the dryer is turned on as a reminder to check the filter. It turns off when the START/PAUSE button is pressed.

CUSTOM PROGRAM

If you have a special combination of settings that you use frequently, you can save these settings as a CUSTOM PROGRAM.

FLOW SENSE™ DUCT BLOCKAGE SENSING SYSTEM INDICATOR

ADD WATER INDICATOR

If the steam feeder is lack for water, this error may be displayed. Fill the feeder and restart the cycle.

OPERATING THE DRYER

CYCLE SETTING BUTTONS

Once you have loaded the dryer:

Press the ON/OFF button to turn on the

dryer. The lights around the cycle selector knob will illuminate.

Turn the cycle selector knob to the desired

cycle. The display will show the preset Dry Level, Temperature, Time, and Option settings for that cycle.

If you would like to change the settings

for that cycle, press the option button(s) to display additional settings for that option. Press the button again to cycle through the settings until the desired setting is highlighted.

NOTE: To protect your garments, not every dry level, temperature, or option is available with every cycle.

Select any additional cycle options, such as ANTI BACTERIAL, DAMP DRY BEEP, WRINKLE CARE or RACK DRY by pressing the button for that option.

SENSOR DRY cycles have preset settings that are selected automatically. MANUAL DRY cycles have default settings, but you may also customize the settings using the cycle setting buttons. Press the button for that option to view and select other settings.

NOTE: To protect your garments, not every dryness level, temperature, or option is available with every cycle. See the Cycle Guide for details.

DRY LEVEL

Selects the level of dryness for the cycle. Press the DRY LEVEL button repeatedly to scroll through available settings.

• This option is only available with SENSOR DRY cycles.

• The dryer will automatically adjust the cycle time. Selecting VERY DRY or MORE DRY will increase the cycle time, while LESS DRY or DAMP DRY will decrease the cycle time.

• Use a LESS DRY or DAMP DRY setting for items that you wish to iron.

Press the START/PAUSE button to begin the

cycle. The display will change, and the dryer will display the estimated (SENSOR DRY) or set

time (MANUAL DRY) remaining and start tumbling. To pause the cycle at any time, press PAUSE. To resume the cycle where it was stopped, press START/PAUSE again.

NOTE: If the dryer has been stopped for more than 8 minutes, the dryer will turn off automatically.

When the load is finished, the beeper (if

set) will sound. If you have set the WRINKLE CARE option, the dryer will tumble the load periodically for up to 3 hours.

To prevent wrinkling, remove items from the dryer immediately after the end of the cycle.

Always clean the lint filter after every cycle.

To clean, pull the lint filter straight up and roll any lint off the filter with your fingers. Do not rinse or wash the filter to remove lint. Push the lint filter firmly back into place.

TEMP. CONTROL

Adjusts the temperature setting from ULTRA LOW to HIGH. This allows precise care of your fabrics

and garments. Press the TEMP. CONTROL button repeatedly to scroll through available settings.

TIME DRY

Allows you to manually select the

drying time, from 20 to 60 minutes,

in 10-minute increments. Use

this for small loads or to remove wrinkles. Use the MORE TIME/LESS TIME buttons to add or reduce the drying time in 1minute increments.

BEEPER

Adjusts the volume of the end-

of-cycle beeper, or turns off the

beeper.

CYCLE OPTION BUTTONS

Your dryer features several additional cycle options to customize cycles to meet your individual needs. Certain option buttons also feature a special function (see the following page for details) that can be activated by pressing and holding that option button for 3 seconds.

To Add Cycle Options to a Cycle:

Turn on the dryer and turn the cycle selector

knob to select the desired cycle. Use the cycle settings buttons to adjust the

settings for that cycle. Press the cycle option button(s) for the

option you would like to add. A confirmation message will be shown in the display.

Press the START/PAUSE button to start the

cycle. The dryer will start automatically.

ANTI BACTERIAL

This option will add a high heat setting to reduce bacteria. It can only be used with the HEAVY DUTY, COTTON/

TOWELS, and NORMAL cycles. NOTE: Do not use this cycle with delicate fabrics.

Certiﬁ ed by NSF

NSF International (formerly the National Sanitation Foundation), certiﬁ es that ANTI BACTERIAL Option reduces 99.9% of bacteria on laundry, and none of bacteria will carry over onto the next laundry

load.

WRINKLE CARE

Selecting this option will tumble the load periodically for up to 3 hours after

the selected cycle, or until the door is opened. This is helpful in preventing wrinkles when you are unable to immediately remove items from the dryer.

DAMP DRY BEEP

With this option, the dryer will beep when the load is approximately 80%

dry. This allows you to remove faster-drying lightweight items or items that you would like to iron or hang while still slightly damp.

+ 102 hidden pages