LG DLEC885W Owner’s Manual

MFL67731090

RELEASING THIS DRAWING WITHOUT PERMISSION LG Electronics SHOULD BE ACCUSED ACCORDING TO THE LAWS AND COMPANY RULES.

이 도면은 LG전자의 자산으로 불법 유출시 관계법과 회사규정에 의해 처벌됨.

SEC.

WORK

적용모델

RC9066A3F

재 질 인쇄방법

모조지 80g OFFSET 인쇄

OFFSET 인쇄

인 쇄 도 수

표 지 내 지

PAGE

REMARK

ECI향

1도 1도

<< 주기 >>

1. 재질, 인쇄방법, 인쇄도수, 외곽치수등은 작업표에 준한다.

2. 인쇄내용, 문자크기 및 형상, 선의 굵기 등은 설계에서 제시된 FILM에 준함.

3. 외곽치수는 절단후 치수임.

4. 양산전에 설계 한도를 득할 것.

68, A5

Enlish French

REV. NO.

기호

210

150

신모델 모델명 추가 EAGI700539 2018.07.23

북미 중재강제조항 적용 관련 문구 추가

지적재산권 보호 문구 삽입

REVISION DESCRIPTION

변경 사항

EAGI100901

EAGH300991

REF. NO.

시방 번호

2018.01.30

2017.03.24

DATE

년/월/일

윤혜진 정영석

최장안

윤혜진

APPROVED

PREPARED

시방자

정영석

승인자

5. 본 부품에 금지물질이 포함되지 않도록 하고, 상세내용은 LG(63)-A-5501-34 를 만족할 것.

<< NOTES >>

1. Material, printing and exterier size are refer to work tables.

2. Printing, text size and line are based on LG design film.

3. Exterier size on the drawing is cutting line.

4. Before product controlled by criteria sample.

5. The part should not contain prohibited substances(Pb,Cd,Hg,Cr+6,PBB, PBDE) and details should comply with LG standard of LG(63)-A-5501-34

DR COMPLETED

도면 DR 완료

완료일 :

TRIG.

MODELING

LG 전자 (주)

LG Electronics Inc.

UNIT SCALE

REVIEWEDDESIGNED

윤 혜 진 윤 혜 진 한 일 탁

16.07.21 16.07.21 16.07.21

CHECKED APPROVED

RELATED DWG.

I T L E

DWG. No.

PDF

ILLUSTRATOR

MANUAL,OWNER’S

PRIME PLUS(D) ECI향

MFL67731090

1/1

OWNER’S MANUAL

DRYER

Read this owner’s manual thoroughly before operating the appliance and keep it handy for reference at all times.

DLEC888W DLEC888R DLEC885W

www.lg.com

MFL67731090

Rev.03_072318

eatures

Ultra Big Capacity Drum

The LG Dryer has a large capacity.

Reduced drying time

Drying time is reduced by the use of an efficient air flow system and an optimized heater.

Innovative Noise Reduction

The optimized design of the air flow system and the vibration reduction technology helps to reduce noise.

Ease of Use

The electronic control has a large, easy to read LED display.

What are Sensor Dry and Manual Dry?

Your dryer provides sensor drying and manual drying programs. Sensor Dry Dryer electronically senses laundry moisture level and automatically determines operation time based on the dryness of the load and the selected program. The control will change the estimated time remaining if it senses a large change in the time needed to complete the cycle. These large increases or decreases in the time display are normal, and do not indicate a product malfunction. Manual Dry Manual Dry allows you to set the desired dry time manually. Certain types of loads, such as large and/or bulky loads, may not dry properly using Sensor Dry. These loads should be dried using the Manual Dry feature to ensure complete drying.

ontents

Safety Instructions .................................................................................. 3

Installation Instructions ............................................................................ 7

Electrical Requirement .......................................................................... 11

Appearance And Design ....................................................................... 14

Operating Your Dryer ............................................................................ 15

Additional Functions............................................................................... 18

Caring For Your Dryer ........................................................................... 22

Additional Tips For Smart Use .............................................................. 25

Troubleshooting Guide .......................................................................... 27

Technical Data ....................................................................................... 32

Warranty ................................................................................................ 33

afety Instructions

READ ALL INSTRUCTIONS BEFORE USE

WARNING

For your safety, the information in this manual must be followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

Your Safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This is the safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others. All safety messages will follow the safety alert symbol and either the word DANGER or WARNING. These words mean:

DANGER: WARNING:

All safety messages will tell you what the potential hazard is, tell you how to reduce the chance of injury, and tell you what can happen if the instructions are not followed.

You can be killed or seriously injured if you don’t immediately follow instructions.

You can be killed or seriously injured if you don’t follow instructions.

BASIC SAFETY PRECAUTIONS

WARNING

Safety Instructions

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:

• Do not install a clothes dryer with flexible

plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers. Flexible venting materials are known to collapse, be easily crushed, and trap lint. These conditions will obstruct clothes dryer airflow and increase the risk of fire.

• Do not store or use gasoline or other flammable

vapors and liquids in the vicinity of this appliance or any other appliances.

• Installation and service must be performed by a qualified installer, service agency, or the gas supplier.

• Install the clothes dryer according to the manufacturer’s instructions and local codes.

• Save these instructions.

• Certain internal parts are intentionally not grounded

and may present a risk of electronic shock only during serving. Service personnel - do not contact the following parts while the appliance is energized: Motor

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will reduce the risk of electric shock by providing a path of least resistance for electric current. This appliance must be equipped with a cord having an equipment-grounding conductor and a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and grounded in accordance with all local codes and ordinances.

Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper outlet installed by a qualified electrician. This appliance must be connected to a grounded metal, permanent wiring system or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. Electrical shock can result if the dryer is not properly grounded.

afety Instructions

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:

• Read all instructions before using the dryer.

• Before use, the dryer must be properly installed as described in this manual.

• Do not place items exposed to cooking oils in

Safety Instructions

your dryer. Items contaminated with cooking oils may contribute to a chemical reaction that could cause a load to catch fire.

• Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances as they give off vapors that could ignite or explode.

• Do not reach into the dryer if the drum or any other part is moving.

• Do not repair or replace any part of the dryer or attempt any servicing unless specifically recommended in this Use and Care Guide or in published user-repair instructions that you understand and have the skills to carry out.

• Do not tamper with controls.

• Before the dryer is removed from service or discarded, remove the door to the drying compartment.

• Do not allow children to play on or in the dryer. Close supervision of children is necessary when the dryer is used near children.

• Do not use fabric softeners or products to eliminate static unless recommended by the manufacturer of the fabric softener or product.

• Do not use heat to dry articles containing foam rubber or similarly textured rubber-like materials.

• Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

BASIC SAFETY PRECAUTIONS

WARNING

• The interior of the dryer and exhaust vent should be cleaned periodically by qualified service personnel.

• Do not install or store the dryer where it will be exposed to the weather.

• Always check the inside of the dryer for foreign objects.

• Clean lint screen before or after each load.

• Do not spray dry cleaning detergent directly onto the product or use the product to dry clothes left with dry cleaning detergent. Doing so could result in explosion or fire.

• Do not dry clothes stained with combustible materials such as thinners, benzene, solvent, or flammable materials. Doing so could result in explosion or fire. (e.g. flammable cleaning solutions, acetone, alcohol, benzene, gasoline, stain-removing turpentine, wax, wax removers, hair gel, hair spray, edible oils, oil, creams, cosmetic products and lotions, oil stains)

• Do not dry clothes stained with oil substances. Oil substances (including edible oils) stained on clothes cannot be completely removed even after washing with water, and could result in fire.

• Remove clothes from the product immediately when drying is complete or the power is turned off during the drying process.

• Leaving clothes that has been dried in the product unattended could result in fire.

• Clothes removed from the product after drying could result in fire. Remove clothes immediately after drying, and then hang or lay the clothes flat to cool.

WARNING

Improper connection of the equipment-grounding conductor can result in a risk of electric shock. Check with a qualified electrician or service person if you are in doubt as to whether the appliance is properly grounded.

afety Instructions

SAFETY INSTRUCTIONS FOR INSTALLATION

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:

Safety Instructions

• Properly ground dryer to conform with all governing codes and ordinances. Follow

details in the installation instructions. Electrical shock can result if the dryer is not properly grounded.

• Before use, the dryer must be properly

installed as described in this manual.

Electrical shock can result if the dryer is not properly grounded.

• Install and store the dryer where it will not

be exposed to temperatures below freezing or exposed to the weather.

• All repairs and servicing must be performed by an authorized servicer unless specifically recommended in this Owner’s Guide. Use only authorized factory parts.

Failure to follow this warning can cause serious injury, fire, electrical shock, or death.

• To reduce the risk of electric shock, do not

install the dryer in humid spaces. Failure to follow this warning can cause serious injury, fire, electrical shock, or death.

• Connect to a properly rated, protected, and

sized power circuit to avoid electrical overload. Improper power circuit can melt,

creating electrical shock and/or fire hazard.

• Remove all packing items and dispose of all shipping materials properly. Failure to do so can result in death, explosion, fire, or burns.

• Place dryer at least 18 in. above the floor for a garage or basement installation. Failure to do so can result in death, explosion, fire, or burns.

• Keep all packaging from children. Packaging material can be dangerous for children. There is a risk of suffocation.

• Do not install nearby heat item. Such as stove, cooking oven. Failure to do so can cause damage, smoke, and fire.

• Do not place candle and cigarettes on top of the product. Failure to do so can cause damage, smoke, and fire.

• Remove all protective vinyl film from the product. Failure to do so can cause damage, smoke, and fire.

• Certain internal parts are intentionally not grounded and may present a risk of electronic shock only during serving. Service personnel - do not contact the following parts while the appliance is energized: Motor

READ ALL INSTRUCTIONS BEFORE USE

afety Instructions

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:

SAFETY INSTRUCTIONS FOR INSTALLATION

• Do not, under any circumstances, cut or remove the ground prong from the power cord. To prevent personal injury or damage to the

Safety Instructions

dryer, the electrical power cord must be plugged into a properly grounded outlet.

• For personal safety, this dryer must be properly grounded. Failure to do so can result in electrical shock or injury.

• Refer to the installation instructions in this manual for specific electrical requirements for your model. Failure to follow these instructions can create an electrical shock hazard and/or a fire hazard.

• This dryer must be plugged into a properly grounded outlet. Electrical shock can result if the dryer is not properly grounded. Have the wall outlet and circuit checked by a qualified electrician to make sure the outlet is properly grounded. Failure to follow these instructions can create an electrical shock hazard and/or a fire hazard.

• The dryer should always be plugged into its own individual electrical outlet which has a voltage rating that matches the rating plate. This provides the best performance and also prevents overloading house wiring circuits which could cause a fire hazard from overheated wires.

• Never unplug your dryer by pulling on the power cord. Always grip plug firmly and pull straight out from the outlet. The power cord can be damaged, resulting in a risk of fire and electrical shock.

• Repair or replace immediately all power cords that have become frayed or otherwise damaged. Do not use a cord that shows cracks or abrasion damage along its length or at either end. The power cord can melt, creating electrical shock and/or fire hazard.

• When installing or moving the dryer, be careful not to pinch, crush, or damage the power cord. This will prevent injury and prevent damage to the dryer from fire and electrical shock.

SAVE THESE INSTRUCTIONS

nstallation Instructions

The following instructions will help guide you through the initial steps of setting up your dryer for use.

Please note that every section of this manual provides important information regarding the preparation and use of your dryer, and it is important that you review this entire manual before proceeding with any installation or use. More detailed instructions concerning electrical connections, gas connections, and exhaust requirements are provided in other parts of this manual.

Positioning the Dryer.

Choose a location with a solid floor for your dryer. Place the dryer at least eighteen inches above the floor for a garage installation. After placing the dryer in the desired location, make sure that it has the required clearances shown.

Installation Instructions

33 1/2"

(850 mm)

/4"

(640 mm)

/8"

(600 mm)

Note

Leveling legs should be secured.

All four legs should be on a solid, even floor and properly leveled as shown in this manual.

If dryer is not level, laundry may not be able to accurately detect the moisture level in the clothes.

When leveling, please be cautious to avoid injury.

nstallation Instructions

Electrical Connections

Preparation of the Dryer

Following are several warnings and instructions concerning making the electrical connection for electric dryers. More detailed information concerning the electrical connection is provided at the manual section entitled Electrical Requirements For Electric Dryer and it is important that you thoroughly review that section, and the remainder of this manual, before taking any steps to install or use this dryer.

1. Use only a new U.L. listed No. 10 (copper wire only) conductor power supply cord kit rated 230 Volts (minimum) 30 Amperes and labeled as suitable for use in a clothes dryer.

2. 4-wire cord is required for manufactured (mobile) home installations and use and where local codes

Installation Instructions

do not allow grounding of this appliance through neutral. As well as all new construction after January 1, 1996.

3. For additional instruction on connecting the dryer to an electrical power source, please refer to this manual’s section on Electrical Requirements for Electric Dryer.

WARNING

• Use a new UL approved 30 amp power supply cord or 10 gauge solid copper wire.

• Use a UL approved strain relief.

• Disconnect power before making electrical connections.

• Connect neutral wire (white or center) to center terminal.

• Ground wire (green or bare) must be connected to green ground connector.

• Securely tighten all electrical connections

• See installation instructions for complete instructions.

• A 4-wire connection is required for all mobile and manufactured home installations, as well as all new construction after January 1, 1996.

• Failure to do so can result in fire or electrical shock.

Prior to the first use of this appliance, use all-purpose cleaning products or a solution of detergent and water, with a damp cloth to remove from the inside of the dryer drum/drying compartment any dust or dirt that may have accumulated in the inside of the dryer. Plug in your dryer after reviewing the following parts on your dryer’s Electrical Requirements.

Confirming Heat Source Operation

Close the door to the dryer drum/drying compartment and, after completing all steps in this manual for proper installation of this dryer, start the dryer on a heat setting, as described more fully in the operating instructions that accompany the dryer.

Additional Instructions for Installation of Your Dryer in a Manufactured or Mobile Home

The following instructions are applicable to installations of the dryer in a manufactured or mobile home. Any installation in a manufactured or mobile home must comply with the Manufactured Home Construction and Safety Standards Title 24 CFR, Part 32-80 or Standard CAN/CSA Z240 MH and local codes and ordinances. If you are uncertain whether your proposed installation will comply with these standards, please contact a service and installation professional for assistance.

1) The electrical connection for an electric dryer must be a 4-wire connection. More detailed information concerning the electrical connection is provided at the manual section entitled Electrical Requirements for Electric Dryer

nstallation Instructions

Stacking Kit

In order to stack this dryer an LG stacking kit is required.

Dryer

Washer

WARNING

• Incorrect installation can cause serious accidents.

• The weight of the dryer and the height of installation makes the stacking procedure too risky for one person. This procedure should be performed by 2 or more experienced service personnel.

• The dryer is not suitable for a built-in installation. Please do not install as a builtin appliance.

• Do not operate if the dryer is disassembled.

Installation Instructions

This dryer may only be stacked on top of an LG washer. DO NOT attempt to stack this dryer on any other washer, as damage, injury or property damage could result.

Washer Top plate size

21 7/8 inch

(550mm)

23 5/8 inch

(600mm)

Shape

and

assembly

direction

Installation Procedure

1. Place the LG dryer on the LG washing machine.

2. Remove the two screws from the bottom of the rear cover on each side as illustrated below.

3. Align the stacking kit holes and the rear cover holes.

3-1) 23

3-2) 21 7/8 inch(550mm)

• Fasten the 2 screws that were removed earlier

from the dryer to the stacking kit.

• Use 4 screws in accessory box [0.6inch(16mm)]

to assemble washer rear cover and stacking kit.

• The procedure for the opposite side will be the

same.

/8 inch(600mm)

Level the dryer

Installation Instructions

nstallation Instructions

1. Level the dryer is to prevent undesirable noise

and vibration.

Locate your dryer on a solid, level floor. Make sure it is not subjected to splashing water or freezing temperatures. Do not store flammable materials near the dryer.

Adjustable feet

Raise Lower

Adjustable feetAdjustable feet

2. If the dryer is not properly level, adjust the front

leveling legs up and down as necessary.

Turn the legs clockwise to raise the dryer and counterclockwise to lower the dryer. Check the dryer diagonally to make sure it does not rock either way. Readjust the legs if necessary.

Diagonal Check

❊

When pushing down corners of the dryer, the machine should not move at all. (Check in either direction.) If machine rocks when pushing the machine top plate diagonally, adjust the feet again.

lectrical Requirement

CONNECTING ELECTRIC DRYERS

WARNING

To help prevent fire, electric shock, serious injury, or death, the wiring and grounding must conform to the latest edition of the National Electrical Code, ANSI/NFPA 70 and all applicable local regulations. Please contact a qualified electrician to check your home’s wiring and fuses to ensure that your home has adequate electrical power to operate the dryer.

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:

• This dryer must be connected to a grounded metal,

permanent wiring system, or an equipmentgrounding conductor must be run with the circuit conductors and connected to the equipmentgrounding terminal or lead on the dryer. Failure to do

so can result in fire, explosion, or death.

• The dryer has its own terminal block that must be

connected to a separate 230 VAC, 60-Hertz, single-phase circuit, fused at 30 amperes (the circuit must be fused on both sides of the line.) ELECTRICAL SERVICE FOR THE DRYER SHOULD BE OF THE MAXIMUM RATE VOLTAGE LISTED ON THE NAMEPLATE. DO NOT CONNECT DRYER TO 110-, 115-, OR 120-VOLT CIRCUIT. Heating elements are available for field installation in dryers which are to be connected to an electrical service of a different voltage than that listed on the rating plate. Failure to

follow these instructions can result in fire, explosion, or death.

• If branch circuit to dryer is 15 ft. (4.5 m) or less in

length, use UL (Underwriters Laboratories) listed No.10 AWG wire (copper wire only), or as required by local codes. If over 15 ft. (4.50 m), use UL-listed AWG wire (copper wire only), or as required by local codes. Allow sufficient slack in wiring so dryer can be moved from its normal location when necessary.

Failure to do so can result in fire, explosion, or death.

No.-8

• The power cord (pigtail) connection between wall receptacle and dryer terminal block IS NOT supplied with dryer. Type of pigtail and gauge of wire must conform to local codes and with instructions on the following pages. Failure to follow these instructions can

result in fire, explosion, or death.

• A 4-wire connection is required for all mobile and

manufactured home installations, as well as all new construction after January 1, 1996. A 4-wire connection must be used where local codes do not permit grounding through the neutral wire. Failure to

do so can result in fire, explosion, or death.

• Do not modify the plug and internal wire provided with the dryer.

• If it does not fit the outlet, a proper outlet will need to be installed by a qualified electrician.

Special Electrical Requirements for Mobile or Manufactured Homes

WARNING

To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:

• Any installation in a manufactured or mobile home must comply with the Manufactured Home Construction and Safety Standards Title 24 CFR, Part 32-80 or Standard CAN/ CSA Z240 MH and local codes and ordinances.

• A 4-wire connection is required for all mobile and

manufactured home installations, as well as all new construction after January 1, 1996.

Failure to do so can result in fire, explosion, or death.

Electrical Requirement For Electric Dryers

lectrical Requirement

4-Prong plug

Review the following options to determine the appropriate electrical connection for your home:

4-wire receptacle (NEMA type14-30R)

Use the instructions in this section if your home has a 4-wire receptacle (NEMA type 14-30R) and you will be using a UL listed, 115/230 volt minimum, 30 amp, dryer power supply cord.

• lf your local codes or ordinances do not allow the use of a 3 wire connection, or you are installing your dryer in a mobile home, you must use a 4wire connection.

: 4-wire connection with

a Power supply cord.

3-wire receptacle (NEMA type10-30R)

Use the instructions in this section if your home has a 3-wire receptacle (NEMA type 10-30R) and you will be using a UL listed, 115/230 volt minimum, 30 amp, dryer power supply cord.

Note

Electrical Requirement For Electric Dryers

• Be sure the screws of the terminal block are tightened firmly. Failure to properly tighten the screws can result in fire, or property damage.

• If you are not sure of the power supply wires or cannot tell which are hot and neutral, consult a qualified electrician.

• If you are not sure if your electric outlet is wired properly, consult a qualified electrician. Connecting the power supply incorrectly can result in product damage, fire, injury or death.

• Direct wiring is not permitted by code in most locations. It is the customer's responsibility to ensure that the installation meets all local codes.

1. Connect neutral wire (white) of power cord to center terminal block screw.

2. Connect red and black wire to the left and right terminal block screws.

3. Connect ground wire (green) of power cord to external ground screw and move neutral ground wire of appliance and connect it to center screw.

4. Make sure that the strain relief screw is tightened and be sure that all terminal block nuts are on tight and power cord is in right position.

lectrical Requirement

: 3-Wire Connection with

a Power Supply Cord

: Optional 3-wire

connection.

lf your local codes or ordinances permit the connection of a frame-grounding conductor to the neutral wire, use these instructions. If your local codes or ordinances do not allow the connection of a frame-grounding conductor to the neutral wire, use the instructions under

Section 3: Optional 3-wire connection.

• If your local codes or ordinances do not allow the connection of a frame-grounding conductor to the neutral wire, use the instructions under this section.

Electrical Requirement For Electric Dryers

1. Connect neutral wire (white) of power cord to

center terminal block screw.

2. Connect ground wire of appliance and neutral

wire of power cord to center terminal block screw.

3. Connect red and black wire to the left and right

terminal block screws.

4. Make sure that the strain relief screw is tightened.

and be sure that all terminal block nuts are on tight and power cord is in right position.

ppearance And Design

Water Container

Condenser Cover

Control Panel

Door

Appearance And Design

Air Ventilation Grill

Control Panel

Cycle Selector Knob

LED Display

• Time Display

• Indicator Lamps

Power

Start/Pause

Additional Function Buttons

• More Time • Time Delay

• Less Time • Custom PGM

• Option • Wrinkle Care

• Signal • Drum Light

perating Your Dryer

Cycle Selection Table

Cotton

Mixed Fabrics

Easy Care

Bulky Items

Jeans

Soft Care

Quick Dry

Sports Wear

Delicates

Wool

Gentle Air

Cool Air

Warm Air

SENSOR DRY CYCLES

Quilts, small comforters and blankets

Terry towels, tea towels, towels, bed linen

Bath towels, tea towels, underwear, cotton socks

Sheets, pillowcase, towels For fabrics which do not need to be ironed Bed linen, table linen, towels,

T-shirts, polo shirts, and work clothes

Bed linen, table linen, tracksuits, parka, blankets

Shirts, blouses For fabrics which do not need to be ironed Trousers, dresses, skirts,

blouses Shirts, T-shirts, trousers,

under-wear and socks Shirts, T-shirts, under-wear,

anoraks and socks Bed clothes, sheets For bulky items

Jeans and colour fading garments.

T-shirts, pillowcase, and towels

A kind of linen and towel except for the special fabrics

Athletic uniform, training wear Silk, Women's thin clothes,

lingerie Wool

Silk, wool, delicate lingerie

All fabrics that need to be fluffed without heat Bath towels, bath robes,

dishclothes, quilted fabrics made of acrylic

For thick and quilted fabrics

For thick and quilted fabrics which do not need to be ironed

For fabrics which do not need to be ironed

For fabrics which do need to be ironed

For thick and quilted fabrics which do not need to be ironed

For fabrics which do need to be ironed

For polyamide, acrylic, and polyester that do not need to be ironed

For polyamide, acrylic, polyester that do need to be ironed

For jeans which do not need to be ironed

For cotton fabrics which do not need to be ironed

For the small loads of qualified fabrics with short drying times

For polyester material

For fabrics which are heat-sensitive like synthetic fabrics

For wool fabrics

MANUAL DRY CYCLES

Refreshes clothes without tumble drying (It can use the dryer rack.)

Small clothes and pre-dried laundry normal fabrics using hot temperature

Drying

Level

Very

Normal

Less

Damp

Normal

Damp

Normal

Damp

Temp.

High

Medium

High

Medium

High

Medium

High High

Low

Medium

Ultra Low

Adjustable

Operating Your Dryer

CAUTION

If the load is less than 2.2lbs (1kg), please use Warm course in MANUAL DRY course. Your wool should be used in Wool program and heat-sensitive fabrics including silk, underwears, lingerie should be used in Delicates course. And also please comply with the recommended laundry load when you use the special fabric course. (Refer to page 25) Otherwise, these clothes may not dry properly.

perating Your Dryer

BEFORE YOU USE YOUR DRYER

1. When unpacking your dryer, make sure there is no visible damage to the machine.

2. Follow the installation instructions and use a level to ensure proper installation.

3. Check the water reservoir, condenser, door, gasket and drum for signs of damage.

4. Run the dryer for a few minutes to make sure it is heating properly.

Operating Your Dryer

1. Turn power on.

First, press the Power button. The indicator light above the button will become illuminated, indicating that the machine is ready set to run.

2. Open the door.

3. Check the lint filter, water container, and condenser.

The lint filter near the door, should be emptied before drying operation. Open and check if lint filter is cleaned. If not, clean it referring to page 22. Water container and condenser are also checked to be emptied and cleaned for better drying result.

4. Place laundry into the drum after sorting.

The clothes should be sorted by fabric type and dryness level and all the strings and belts of clothes should be secured before being put into the drum. Push the laundry all the way back to keep it away from the door seal. If not, the door seal and clothes may be damaged.

Turn the dryer on.

Open the door.

Check the lint filter.

5. Close the Door.

perating Your Dryer

Before you close the door, make sure fabrics are properly loaded and not caught in the door opening.

Select the Drying Cycle you want.

You can choose a cycle by turning the Cycle Selector Knob until the required program reaches to its indicator. If you press Start/Pause button without choosing any cycle, the dryer will proceed with the Cotton program. [Please refer to following Cycle Selection Table (page 15) for the detailed information]

Select the desired cycle.

7 . Press the

You can hear the drum turning.

After operation is completed, open the door and remove the laundry.

Be careful! Drum inside could be still hot. (Operation time varies depending on your cycle selection or options.)

9. Clean the lint filters and empty water container.

The lint filter should be cleaned after each load.

10. Turn off the Dryer.

Press the Power button.

SSttaarrtt//PPaauussee

button.

CAUTION

Take out the laundry.

Operating Your Dryer

Clean the door lint filter.

• Be careful the filter is not torn or damaged when using a vacuum cleaner. If there is a little residue buildup on filter, you can scrub lint screen with a brush to remove.

• If you want to open the door while dryer is operating, please press the Start/Pause button first, wait until drum completely stops and then open the door.

dditional Functions

Time Delay

The Time Delay feature allows you to have the dryer run at a time that is more convenient, for example when electricity rates are cheaper. The cycle can be delayed from 3 hours up to a maximum of 19 hours.

1. Load the dryer and close the door.

2. Press the Power button.

3. Select the desired cycle and options.

4. Press the Time Delay button until the

5. Press the Start/Pause button.

Additional Functions

Wrinkle Care ( )

Selecting this option will tumble the load periodically for a few seconds without heat. This will continue for up to 2 hours after the selected cycle, or until the door is opened. This prevents wrinkling of unremoved dry items until they can be removed.

desired delay time is displayed.

Note

If the door is opened during the drying portion of a cycle before Wrinkle Care has started, the cycle will not be cancelled and Wrinkle Care will begin as soon as the normal drying portion of the cycle is completed.

Custom PGM

If you have a special combination of settings that you use frequently, you can save these settings as a Custom PGM.

To Save a Custom PGM

1. Turn on the dryer.

2. Select a cycle.

3. Use the cycle modifier buttons to adjust the settings for that cycle.

4. Set any other desired cycle options.

5. Press and hold the Custom PGM button for 3 seconds. You will hear two beeps to confirm the settings have been stored.

To Recall a Custom PGM

1. Press and release the Custom PGM button. The stored settings will be displayed.

2. Press and release the Cycle Selector Knob to start the cycle. The dryer will start automatically.

Note

You can only save one Custom PGM program at a time. If you press and hold the Custom PGM button for 3 seconds, you will overwrite any previously stored Custom PGM settings. Once Custom PGM has been recalled, any of the memorized modifiers or options can be adjusted. However, if the Cycle Selector Knob is rotated, Custom PGM will be cancelled.

dditional Functions

More Time / Less Time

The More Time and Less Time buttons can be used to increase or decrease the dry time when MANUAL DRY cycles are selected. These buttons are disabled once the cycle is started.

Temp.

Adjusts the temperature setting from Ultra Low to High. This allows precise care of your fabrics and garments.

• Press the Temp. button repeatedly to scroll

through available settings.

Note

These buttons are available only with MANUAL DRY, before you push Start/Pause button.

Drum Light

Press the Drum Light button to turn on the drum light during dryer operation. This will allow you to more easily observe the load. The drum light will come on any time the door is opened.

Options

Gentle

- This function keeps the garments more moist than the standard Iron dry level.

- Cotton, Mixed Fabircs and Easy Care cycles.

Damp Dry Signal

- This option causes the control to beep once the clothes have reached a "Damp Dry Signal" level. This can be used to alert you to remove articles that you don't want to over dry or that you want to have damp for easier ironing.

- Cotton, Mixed Fabircs and Easy Care cycles.

Additional Functions

Signal

Press the Signal button to adjust the volume of the signals from high to off.

Child Lock( )

Use this option to prevent cycle settings from being changed while the dryer is operating. Press and hold the Dry Level button for 3 seconds to activate or deactivate the Child Lock function.

The lock icon will be shown in the display, and all controls are disabled.

dditional Functions

• The Tag On function allows you to conveniently use the LG SmartDiagnosis™ and Cycle Download features to

communicate with your appliance right from your own smart phone.

•To use the Tag On function:

1. Download the LG Smart Laundry & DW App to your smart phone.

2. Turn on the NFC (Near Field Communication) function in your smart phone.

• The Tag On function can only be used with most smart phones equipped with the NFC function and based on the Android operating system (OS).

Turning on the NFC function of the smart phone

1. Enter the "Settings" menu of the smart phone and

select "Share & Connect" under "WIRELESS & NETWORKS".

Additional Functions

2. Set "NFC" and "Direct Android Beam" to ON and

select "NFC".

3. Check "Use Read and Write/P2P receive".

Note

• Depending on the smart phone manufacturer and Android OS version, the NFC activation process may differ.

• Refer to the manual of your smart phone for details.

dditional Functions

The Tag On guide

Tag On position

• Tag On: Look for the Tag On icon next to the LED screen on the control panel. This is where you position your smart phone when using the Tag On function with the LG SmartDiagnosis™ and Cycle Download features of the LG Smart Laundry & DW App.

• When you use the Tag On function, position your smart phone so that the NFC antenna on the back of your smart phone matches the position of the Tag On icon on the appliance. If you do not know the position of your NFC antenna, move your smart phone very slightly in a circular motion until the application verifies the connection.

Additional Functions

•

Because of the characteristics of NFC, if the transmission distance is too far, or if there is a metal sticker or a thick case on the phone, transmission will not be good. In some cases, NFC-equipped phones may be unable to transmit successfully.

•

Press in the LG Smart Laundry & DW app for a more detailed guide on how to use the Tag On function.

+ 51 hidden pages