LG DLG5966W, DLG5966G, DLE5955W, DLE5955G Owner’s Manual

To contact LG Electronics, 24 hours a day,

7 days a week:

1=800=243=0000

Or visit us on the Web at: us.lge.com

TROM TM

DRYE S

USER'SGUIDE&

INSTALLMiONINSTRUCTIONS

Before beginning Installation, read these

Instructions carefully. This wll simplify installation

and ensure that the dryer is installed correctly and

safely. Leave these instructions near the dryer

after installation for future reference.

TRO ,M

SECADORAS

GLIIADE[ LISUARIOE

INSTRUcCiONESDE INSTA[AclON

Pour contacter LG Electronics, 24 heures par jour, 7 jours par semaine :

1=800=243=0000

ou visitez notre site Web & I'adresse :

us./ge.com

Antes de comenzar la instalacion, lea atentamente

estas instrucciones. Esto simplificara la instalaciOn

y asegurara que la secadora esta instalada

en forma correcta y segura. Conserve estas

instrucciones cerca de la secadora luego de la

instalacion para futuras consultas.

M0dels/M0del0s

[-le¢[ri€/El(_€[rica

DLE5955W DLE5955G

C,as/C,as

DLGBg66w DLGBg66G

P/No. 3828EL3003S

INTRODUCTION

IMPORTANT SAFETY INSTRUCTIONS

Basic Safety Precautions ....................................... 3

What to Do if You Smell Gas .................................. 4

Grounding Instructions .......................................... 5

Safety Instructions for Installation ...................... 5, 6

Safety Instructions for Connecting Electricity ....... 7

PARTSAND FEATURES

Special Features ..................................................... 8

Key Parts and Components ................................... 9

THANKYOU!

Congratulations on your purchase

and welcome to the LG family. Your

INSTALLATION INSTRUCTIONS

Choose the Proper Location ................................ 10

Clearances ........................................................... 10

Installation With Optional

Pedestal Base or Stacking Kit .............................. 11

Leveling the Dryer ................................................ 12

Reversing the Door Swing .................................... 12

Changing the Dryer Vent Location ....................... 13

Venting the Dryer ............................................ 14, 15

Connecting Gas Dryers ................................... 16 17

Connecting Electric Dryers ................................... 18

Special Requirements for Manufactured

or Mobile Homes .................................................. 19

Final Installation Check ....................................... 19

Duct Condition Testing ......................................... 20

HOW TO USE

Sorting Loads ....................................................... 21

Loading the Dryer ................................................. 21

Check the Lint Filter Before Every Load ............... 21

Control Panel Features ......................................... 22

Cycle Guide .......................................................... 23

The Time and Status Display ............................... 24

The Duct Blockage Sensing System .................... 24

Operating the Dryer .............................................. 25

Cycle Setting Buttons .......................................... 26

Cycle Option Buttons .......................................... 27

Special Functions ................................................. 28

Custom Program .................................................. 28

new LG Dryer combines the most

advanced drying sensor technology

with simple operation and high

efficiency. By following the

operating and care instructions

in this manual, your dryer will

provide you with many years of

reliable service.

CARE AND CLEANING

Regular Cleaning .................................................. 29

TROUBLESHOOTING

Before Calling for Service ............................... 30-32

SPECIFICATIONS/OPTIONAL

ACCESSORIES

Optional Accessories ........................................... 32

Pedestal Installation ....................................... 33, 34

Stacking Kit installation .................................. 35, 36

Key Dimensions and Specifications ..................... 36

WARRANTY

Product Information Registration ......................... 37

! PORTANTSAFETYINSTRUCTIONS

READ ALL iNSTRUCTiONS BEFORE USE

WARNING Foryo.rsafeW,theinformationinthisman,alre,stbe

followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

YOur Safety and the safety of others is very important.

We have provided many important safety messages in this manual and on your appliance. Always read and obey all safety messages.

This iSthe safety alert symbol.

This symbol alerts you to potential hazards that can kill or hurt you and others.

All safety messages will follow the safety alert symbol and either the word DANGER or WARNING. These words mean:

kDANGER: Youcanbe killed or seriously injured if you don't immediately follow instructions.

_h_WARN|NG-" You can be killed or seriously injured if you don't follow instructions. All safety messages will tell you what the potential hazard is, tell you how the reduce the chance of

injury, and tell you what can happen if the instructions are not followed.

BASIC SAFETY PRECAUTIONS

&WARNING; To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Read all instructions before using the dryer.

• Before use, the dryer must be properly installed as described in this manual.

Do not place items exposed to cooking oils in your dryer. Items contaminated with cooking

oils may contribute to a chemical reaction that could cause a load to catch fire.

Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted

with gasoline, dry-cleaning solvents, other flammable or explosive substances as they give

off vapors that could ignite or explode. Do not reach into the dryer if the drum or any

other part is moving. Do not repair or replace any part of the dryer

or attempt any servicing unless specifically recommended in this Use and Care Guide or

in published user-repair instructions that you understand and have the skills to carry out.

Do not tamper with controls. Before the dryer is removed from service or

discarded, remove the door to the drying compartment.

Do not allow children to play on or in the dryer. Close supervision of children is necessary when

the dryer is used near children.

• Do not use fabric softeners or products to eliminate static unless recommended by the

manufacturer of the fabric softener or product. Do not use heat to dry articles containing

foam rubber or similarly textured rubber-like materials.

Keep area around the exhaust opening and adjacent surrounding areas free from the accumulation of lint, dust, and dirt.

The interior of the dryer and exhaust vent should be cleaned periodically by qualified

service personnel. Do not install or store the dryer where it will be

exposed to the weather. Always check the inside of the dryer for foreign

objects Clean lint screen before or after each load.

The dryer must not be installed or stored in an area where it will be exposed to water.

I PORTANTSAFETY INST UcTIONS

READ ALL iNSTRUCTiONS BEFORB USE

_WARNING Foryoursafe_,theinformationinthismanualmustbe

followed to minimize the risk of fire or explosion, electric shock, or to prevent

property damage, personal injury, or loss of life.

• Do not store or use gasoline or other flammable vapors and liquids in the

vicinity of this appliance or any other

appliances.

• Installation and service must be performed by a qualified installer,

service agency, or the gas supplier.

WHAT TO DO iF YOU SMELL GAS:

1. Do not try to light a match or cigarette, or turn on any gas or electrical

appliance.

2. Do not touch any electrical switches. Do not use any phone in your building.

3. Clear the room, building, or area of all occupants.

CALIFORNIA SAFE DRINKING WATER AND TOXIC ENFORCEMENT ACT

This act requires the governor of California to publish a list of substances known to the state to cause

cancer, birth defects, or other reproductive harm and requires businesses to warn customers of potential exposure to such substances.

Gas appliances can cause minor exposure to four of these substances, namely benzene, carbon monoxide,

formaldehyde, and soot, caused primarily by the incomplete combustion of natural gas or LP fuels.

4. immediately call your gas supplier from

a neighbor's phone. Follow the gas supplier's instructions carefully.

5. if you cannot reach your gas

supplier, call the fire department.

Properly adjusted dryers will minimize incomplete combustion. Exposure to these substances can be minimized further by properly venting the dryer to the outdoors.

! PORTANTSAFETY INSTRUCTIONS

READ ALL iNSTRUCTiONS BEFORE USE

WARNING Foryo.rsafe ',theinformationinthisman.alre,stbe

followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

GROUNDING INSTRUCTIONS

This appliance must be grounded. In the event of malfunction or breakdown, grounding will

reduce the risk of electric shock by providing a path of least resistance for electric current.

This appliance must be equipped with a cord having an equipment-grounding conductor and

a grounding plug. The plug must be plugged into an appropriate outlet that is properly installed and

grounded in accordance with all local codes and ordinances.

WARNING --,mproper

connection of the equipment-grounding conductor can resultina riskofelectricshock.

Check with a qualified electrician or service

person if you are in doubt as to whether the appliance is properly grounded.

Do not modify the plug provided with the appliance. If it will not fit the outlet, have a proper

outlet installed by a qualified electrician. This appliance must be connected to a grounded

metal, permanent wiring system or an equipment- grounding conductor must be run with the circuit

conductors and connected to the equipment- grounding terminal or lead on the appliance.

Electrical shock can result if the dryer is not properly grounded.

SAFETY INSTRUCTIONS FOR INSTALLATION

,WARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Properly ground dryer to conform with all

governing codes and ordinances. Follow details in the installation instructions. Electrical

shock can result ifthe dryer is not properly grounded.

• Before use, the dryer must be properly

installed as described in this manual.

Electrical shock can result if the dryer is not properly grounded.

• install and store the dryer where it will not be

exposed to temperatures below freezing or

exposed to the weather.

• All repairs and servicing must be performed

by an authorized servicer unless specifically recommended in this Owner's Guide. Use

only authorized factory parts. Failure to follow this warning can cause serious injury,fire,

electrical shock or death.

• To reduce the risk of electric shock, do not install the dryer in humid spaces. Failure to

follow this warning can cause serious injury, fire, electrical shock or death.

• Connect to a properly rated, protected, and sized power circuit to avoid electrical

overload. Improper power circuit can melt, creating electrical shock and/or fire hazard.

• Remove all packing items and dispose of all shipping materials properly. Failure to do so

can result in death, explosion, fire or burns.

• Place dryer at least 18 in. above the floor for a garage installation. Failure to do so can

result in death, explosion, fire or burns.

• Keep all packaging from children. Packaging material can be dangerous for children. There is

a risk of suffocation.

I PORTANTSAFETY INST UcTIONS

READ ALL iNSTRUCTiONS BEFORE USE

WARNING Foryo.rsafew,theinformationinthisman.alre.stbe

followed to minimize the risk of fire or explosion, electric shock, or to prevent property damage, personal injury, or loss of life.

SAFETY INSTRUCTIONS FOR INSTALLATION

Exhaust/Ducting:

• Gas dryers MUST be exhausted to the outside. Failure to follow these instructions

can result in fire or death.

• The dryer exhaust system must be exhausted to the outside of the dwelling, if the dryer is

not exhausted outdoors, some fine lint and large amounts of moisture will be expelled

into the laundry area. An accumulation of

lint in any area of the home can create a health and fire hazard.

,,Use only rigid metal or flexible metal 4-in.

diameter ductwork inside the dryer cabinet or for exhausting to the outside. Use of

plastic or other combustible ductwork can

cause a fire. Punctured ductwork can cause a fire if itcollapses or becomes otherwise

restricted in use or during installation.

• Ductwork is not provided with the dryer, and you should obtain the necessary ductwork

locally. The end cap should have hinged dampers to prevent backdraft when the dryer

is not in use. Failure to follow these instructions can result infire or death.

• The exhaust duct must be 4 in. (10 cm) in diameter with no obstructions. The exhaust

duct should be kept as short as possible.

Make sure to clean any old ducts before installing your new dryer. Failure to follow

these instructions can result in fire or death.

',Rigid or semi rigid metal ducting is

recommended for use between the dryer and the wall. in special installations

when it is impossible to make a connection with the above recommendations, a UL=

listed flexible metal transition duct may be

used between the dryer and wall connection only. The use of this ducting will affect drying

time. Failure to follow these instructions can result infire or death.

• DO NOT use sheet metal screws or other fasteners which extend into the duct that

could catch lint and reduce the efficiency of the exhaust system. Secure all joints with duct tape. For complete details, follow the Installation Instructions. Failure to follow these instructions can result in fire or death.

! PORTANTSAFETY INSTRUCTIONS

READ ALL iNSTRUCTiONS BEFORE USE

_WARNING Foryo.rsafe_',theinformationinthisman.alre,stbe

followed to minimize the risk of fire or e×plosion, electric shock, or to prevent property damage, personal injury, or loss of life.

SAFETY iNSTRUCTiONS FOR CONNECTING ELECTRiCiTY

&WARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Do not, under any circumstances, cut or remove the ground prong from the power

cord. To prevent personal injury or damage to the dryer, the electrical power cord must be

plugged into a properly grounded outlet.

• For personal safety, this dryer must be properly grounded. Failure to do so can result

in electrical shock or injury.

• Refer to the installation instructions in this manual for specific electrical requirements

for your model. Failure to follow these instructions can create an electrical shock

hazard and/or a fire hazard.

• This dryer must be plugged into a properly grounded outlet. Electrical shock can result if

the dryer is not properly grounded. Have the wall outlet and circuit checked by a qualified

electrician to make sure the outlet is properly grounded. Failure to follow these instructions

can create an electrical shock hazard and/or a fire hazard.

• The dryer should always be plugged into its own individual electrical outlet which

has a voltage rating that matches the rating plate. This provides the best performance

and also prevents overloading house wiring circuits which could cause a fire hazard from

overheated wires.

• Never unplug your dryer by pulling on the power cord. Always grip plug firmly and pull

straight out from the outlet. The power cord can be damaged, resulting in a risk of fire and

electrical shock.

• Repair or replace immediately all power cords that have become frayed or otherwise

damaged. Do not use a cord that shows cracks or abrasion damage along its length

or at either end. These power cord can melt, creating electrical shock and/or fire hazard.

= When installing or moving the dryer, be

careful not to pinch, crush, or damage the power cord. This will prevent injury and

prevent damage to the dryer from fire and electrical shock.

SAVE THESB iNSTRUCTiONS

PARTSAND FEATURES

SPECIAL FEATURES

O EASY-TO-USE CONTROL PANEL

Rotate the Cycle Selector Knob to select the

desired dry cycle. Adjust settings and add cycle options with the touch of a button.

EASY-ACCESS REVERSIBLE DOOR

Wide-opening door provides easy access for loading and unloading. Door swing can be

reversed to adjust for installation location.

ULTRA=CAPACITY STAINLESS STEEL DRUM

WITH DRUM LIGHT The ultra-large stainless steel drum offers

superior durability. The drum is equipped with a yellow light that illuminates when the dryer door

is open and turns off when the door is closed.

FLOWSENSE MDUCT/FILTER BLOCKAGE

SENSING SYSTEM

The FlowSense TMduct/filter blockage sensing system detects and alerts you to blockages in the

filter and ductwork that reduce exhaust flow from the dryer. This not only helps prevent fires and

save lives, it can improve operating efficiency and help minimize service calls, saving you money.

PARTSAND FEATURES

KEY PARTSAND COMPONENTS

In addition to the special features and components outlined in the Special Features

section, there are several other important components that are referenced in this manual.

O FRONT=MOUNT LiNT FILTER

Front-mounted lint filter allows for easy access

and cleaning after every load.

LEVELING FEET

Four leveling feet (two in the front, and two in

the back) adjust to improve dryer stability on uneven floors.

DRYING RACK

Use the drying rack with the RACK DRY cycle

option. The drying rack allows items, such as sweaters, delicates, and gym shoes, to be placed

in a flat position for drying. Terminal Block

Access Panel (Electric Models)

Included Accessories

O Drying Rack

Gas Connection Location

(Gas Models)

Power Cord Location

(Gas Models)

Exhaust Duct Outlet

Rear of Dryer (Electric Model

Shown)

INSTAL[ATION INST UCTIONS

iMPORTANT: Read all installation instructions completely before

installing and operating your dryer!

It is important that you review this entire manual before installing and using your dryer. Detailed instructions

concerning electrical connections, gas connections, and exhaust requirements are provided on the following pages.

CHOOSE THE PROPER LOCATION

• Store and install the dryer where it will not be exposed to temperatures below freezing or

exposed to outdoor weather conditions. Choose a location with a solid, level floor.

If the dryer is being installed in a garage, place the dryer at least 18 in. (46 cm) above

the floor.

CLEARANCES

o20c Ti 45;7g

4"_ 1_30"_ 1_-4"

(10 cm) (76.1 cm) (10 cm)

• Most installations require a minimum 5V2in. (14 cm) clearance behind the dryer for the

exhaust ducting. Allow minimum clearances of at least 1 in. (2.5 cm) on the sides and back to minimize

vibration and noise. Allowing additional clearance for installation and

servicing is recommended. Be sure to allow for wall, door, or floor moldings

that may increase the required clearances. Allow at least 24 in. (61 cm) in front of the dryer

to open the door.

18"

1"_11_ 27-_11_1"

(2.54 cm) (68,6 cm) (2.54 cm)

50"_

(127 cm)

Properly ground dryer to conform with all governing codes and ordinances.

To reduce the risk of electric shock, do not install the dryer in damp or wet locations.

If you are installing your dryer in a manufactured or mobile home, please refer to the section

Special Requirements for Manufactured or Mobile Homes.

(7.6_m)

48 in.2

(310 cm 2)

24 in.2

(155 cm _)

(7.6cm)

Closet Door Vent

Requirements

Additional Instructions for closet installations:

The closet door must allow for sufficient airflow. Refer to the diagram above for minimum vent

opening requirements. A Iouvered door is also acceptable.

Make sure that there is at least 18 in. (46 cm) of clearance above the dryer.

....J

INSTALLATIONINSTRUCTIONS

INSTALLATIONS WITH OPTIONAL PEDESTAL BASE OR STACKING KIT

iMPORTANT: If you are installing your dryer using an optional pedestal base or stacking

kit, please refer to Optional Accessories in this manual or to the instructions for your pedestal

or stacking kit before proceeding with the

installation.

Required Dimensions for installation

With Pedestal

Required Dimensions for Installation

With Stacking Kit

77V2"

[190.5 cm)

I_ 30,,_1 -_4,,

(76.1 cm) (10 cm)

1"_--II_ 27-_11_1"

(2.54 cm) (68.6 cm) (2.54 cm)

OPTIONAL ACCESSORIES

For these and other LG products, contact your local LG dealer, or visit our Web site at us.lge.com.

Pedestal (sold separately) Stacking Kit (sold separately)

iNSTALLATIONINST UCTIONS

LEVELING THE DRYER

To ensure that the dryer provides optimal drying performance, it must be level. To minimize

vibration, noise, and unwanted movement, the floor must be a perfectly level, solid surface.

NOTE: Adjust the leveling feet only as far as necessary to level the dryer. Extending the

leveling feet more than necessary can cause the dryer to vibrate.

g Feet

Position the dryer in the final location. Place

a level across the top of the dryer.

• All four leveling feet must rest solidly on the floor. Gently push on the top corners of the

dryer to make sure that the dryer does not rock from corner to corner.

If you are installing the dryer on the optional pedestal, you must use the leveling feet on the

pedestal to level the dryer. The dryer leveling feet should be fully retracted.

Use an adjustable wrench to turn the leveling

feet. Turn clockwise to raise the dryer or counterclockwise to lower it. Raise or lower

the leveling feet until dryer is level from side to side and front to back.

Make sure that all 4 leveling feet are in firm

contact with the floor.

REVERSING THE DOOR SWING

The swing of the dryer door can be reversed to fit your installation location.

Door Latch

Hinge

........................ ,/

Open the dryer door. Using a Phillips screw- driver, remove the 2 screws that secure

the door hinge to the dryer door opening.

Remove the 4screws from the latch side of the

dryer door opening, and remove the door latch.

Latch Screws ---'-'_% Screws

Turn the door around so the hinge is reversed, and reattach the door using the

2 screws previously removed. Reinstall the door latch and the 4 screws.

Test the door swing to make sure the door moves freely and latches securely.

"_-. /

\x _x

xx x

_ Hinge

_f Screws

Latch Screws

INSTALLATIONINSTRUCTIONS

CHANGING THE DRYER VENT LOCATION

Your new dryer is shipped to vent to the rear.

It can also be configured to vent to the bottom

or side (right-side venting is not available on gas models).

An adapter kit, part number 383EEL9001 B, may be purchased from your LG retailer. This

kit contains the necessary duct components to change the dryer vent location.

OPTION 1: Side Venting

Rear Exhaust Duct

Remove the rear exhaust duct retaining

screw. Pull out the exhaust duct.

OPTION 2: Bottom Venting

f"_ Adapter

Duct

Bracket

Retaining Screw

Press the tabs on the knockout and carefully

remove the knockout for the desired vent opening (right-side venting is not available on

gas models). Press the adapter duct onto the blower housing and secure to the base of the

dryer as shown.

Cover Plate

Elbow <38 om)

Preassemble a 4-in. (10cm) elbow to the next

4-in. (10 cm) duct section, and secure alljoints with duct tape. Be sure that the male end of

the elbow faces AWAY from the dryer.

Insert the elbow/duct assembly through the

side opening and press it onto the adapter duct. Secure in place with duct tape.

Be sure that the male end of the duct

protrudes 1V2in. (3.8 cm) to connect the remaining ductwork.

Attach cover plate to the back of the dryer with included screw.

Press the adapter duct onto the blower

housing and secure to the base of the dryer as shown.

Cover Plate

Elbow

__J

Insert the 4-in. (10 cm) elbow through the

rear opening and press it onto the adapter duct. Be sure that the male end of the elbow

faces down through hole in the bottom of the dryer. Secure in place with duct tape.

Attach the cover plate to the back of the dryer with included screw.

INSTALLATIONINST UCTIONS

VENTING THE DRYER

&WARN|NG: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Do not crush or collapse ductwork. Failure to follow these instructions can result in fire or

death.

• Do not allow ductwork to rest on or contact sharp objects. Failure to follow these

instructions can result in fire or death.

• if connecting to existing ductwork, make sure it is suitable and clean before installing

the dryer. Failure to follow these instructions can result in fire or death.

• Venting must conform to local building codes. Failure to follow these instructions can

result infire or death.

• Gas dryers MUST exhaust to the outdoors.

Failure to follow these instructions can result in

fire or death.

= Use only 4-in. (10 cm} rigid or flexible metal

ductwork inside the dryer cabinet and for venting outside. Failure to follow these

instructions can result in fire or death.

• To reduce the risk of fire, combustion, or

accumulation of combustible gases, DO

NOT exhaust dryer air into an enclosed and

unventilated area, such as an attic, wall, ceiling, crawl space, chimney, gas vent, or concealed space of a building. Failure to

follow these instructions can result in fire or death.

• To reduce the risk of fire, DO NOT exhaust the dryer with plastic or thin foil ducting.

Failure to follow these instructions can result in

fire or death.

• The exhaust duct must be 4 in. {10 cm) in

diameter with no obstructions. The exhaust duct should be kept as short as possible.

Make sure to clean any old ducts before installing your new dryer. Failure to follow

these instructions can result in fire or death.

• Rigid or semirigid metal ducting is recommended for use between the dryer

and the wall. in special installations when it is impossible to make a connection with the

above recommendations, a UL-listed flexible metal transition duct may be used between

the dryer and wall connection only. The use

of this ducting will affect drying time. Failure

to follow these instructions can result in fire or

death.

= DO NOT use sheet metal screws or other

fasteners which extend into the duct that

could catch lint and reduce the efficiency of

the exhaust system. Secure all joints with

duct tape. Failure to follow these instructions can result in fire or death.

• To maximize operating results, please observe the duct length limitations noted

in the chart above. Failure to follow these instructions can result in fire or death.

• Ductwork is not provided with the dryer.

You should obtain the necessary ductwork

locally. The end cap should have hinged dampers to prevent backdraft when the

dryer is not in use. Failure to follow these instructions can result in fire or death.

INSTALLATIONINSTRUCTIONS

VENTING THE DRYER (cont.)

Ductwork

0 65 ft. (19.8 m) 45 ft. (13.7 m)

Recommended 1 55 ft. (16.8 m) 35 ft. (10.7 m)

2 47 ft. (13.7 m) 30 ft. (9.1 m) 3 36 ft. (11.0 m) 25 ft. (7.6 m)

/_02o,nl /_02oml 4 28 ft. (8.5 m) 20 ft. (6.1 m)

Use Only for Short 0 55 ft. (16.8 m) 35 ft. (10.7 m)

Run Installations 1 47 ft. (13.7 m) 27 ft. (8.1 m)

2 41 ft. (12.5 m) 21 ft. (6.4 m) 3 30ft. (9.1 m) 17ft. (5.2 m)

/........, 4 22 ft. (6.7 m) _../

NOTE: Deduct 6 ft. (1.8 m) for each additional elbow. It is not recommended to use more than four 90 ° elbows.

Routing and Connecting Ductwork

Follow the guidelines below to maximize drying

performance and reduce lint buildup and condensation in the ductwork.

NOTE: Ductwork and fittings are NOT included and must be purchased separately.

• Use 4-in. (10 cm) diameter rigid or semirigid metal ductwork.

• The exhaust duct run should be as short as possible.

• Use as few elbow joints as possible. The male end of each section of exhaust duct must point away from the dryer.

Use duct tape on all duct joints.

Insulate ductwork that runs through unheated areas in order to reduce condensation and lint

buildup on duct surfaces.

iMPORTANT: Failure to exhaust the dryer

correctly will void the dryer's warranty.

Correct Venting

incorrect Venting

INSTALLATIONINST UCTIONS

CONNECTING GAS DRYERS

4_I_WARNING -! To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:

• Gas supply requirements: As shipped from the factory, this dryer

is configured for use with natural gas. It can be converted for use with LP (Liquefied Propane) gas. Gas pressure

must not exceed 13 in. water column.

• A qualified service or gas company technician

must connect the dryer to the gas service. Failure to do so can result in fire, explosion, or

death.

• Isolate the dryer from the gas supply system

by closing its individual manual shutoff valve during any pressure testing of the gas supply.

Failure to do so can result in fire, explosion, or death.

• Supply line requirements:

Your laundry room must have a rigid gas

supply line to your dryer, in the United States, an individual manual shutoff valve MUST be

installed within at least 6 ft. (1.8 m) of the dryer, in accordance with the National Fuel Gas Code ANSI Z223.1. A 1/8=in. NPT pipe plug must be installed. Failure to do so can

result in fire, explosion, or death.

= If using a rigid pipe, the rigid pipe should be

1/2=in. IPS. If acceptable under local codes and ordinances and when acceptable to your gas supplier, 3/8=in. approved tubing may be

used where lengths are less than 20 ft. (6.1 m). Larger tubing should be used for lengths

in excess of 20 ft. (6.1 m). Failure to do so can result in fire, explosion, or death.

• Connect the dryer to the type of gas shown on the nameplate. Failure to do so can result in

fire, explosion, or death.

• To prevent contamination of the gas valve, purge the gas supply of air and sediment before connecting the gas supply to the dryer. Before tightening the connection between the gas supply and the dryer, purge remaining air until the odor of gas is detected. Failure to do so can result infire, explosion, or death.

DO NOT use an open flame to inspect for

gas leaks. Use a noncorrosive leak-detection

fluid. Failure to do so can result infire, explosion,

or death.

• Use only a new AGA- or CSA-certified gas supply line with flexible stainless steel connectors. Failure to do so can result in fire, explosion, or death.

• Securely tighten all gas connections. Failure to do so can result infire, explosion, or death.

Use Teflon® tape or a pipe=joint compound that is insoluble in Liquefied Petroleum (LP)

gas on all pipe threads. Failure to do so can result in fire, explosion, or death.

DO NOT attempt any disassembly of the

dryer; any disassembly requires the attention and tools of an authorized and qualified service person or company. Failure to do so can result infire, explosion, or death.

Electrical Requirements for Gas Models Only

• Do not, under any circumstances, cut or remove the third (ground) prong from the power cord. Failure to follow this warning can result infire, explosion, or death.

For personal safety, this dryer must be properly grounded. Failure to follow this warning can result in fire, explosion, or death.

• The power cord of this dryer is equipped with a 3=prong (grounding) plug which mates with a standard 3=prong (grounding) wall outlet to minimize the possibility of electric shock hazard from this appliance. Failure to follow this warning can result in fire, explosion,

or death.

• This dryer must be plugged into a 120=VAC, 60=Hz. grounded outlet protected by a 15=ampere fuse or circuit breaker. Failure to follow this warning can result infire, explosion, or

death. Where a standard 2=prong wall outlet is

encountered, it is your personal responsibility and obligation to have it replaced with a properly grounded 3-prong wall ouUet. Failure

to follow this warning can result in fire, explosion, or death.

INSTALLATIONINSTRUCTIONS

CONNECTING GAS DRYERS (cont.)

_!_WARNING: To reduce the risk of fire, electric shock, or injury to persons when using this appliance, follow basic precautions, including the following:

• installation and service must be performed by a qualified installer, service agency, or the

gas supplier. Failure to do so can result in fire, explosion, or death.

• Use only a new stainless steel flexible connector and a new AGA-certified

connector. Failure to do so can result in fire,

explosion, or death.

• A gas shutoff valve must be installed within 6 ft. (1.8 m) of the dryer. Failure to do so can

result in fire, explosion, or death.

• The dryer is configured for Natural Gas when shipped from the factory. Make sure that the

dryer is equipped with the correct burner nozzle for the type of gas being used (Natural

Gas or Liquefied Petroleum). Failure to do so can result in fire, explosion, or death.

• If necessary, the correct nozzle (for the LP

nozzle kit order part number 4948EL4002B} should be installed by a qualified technician

and the change should be noted on the dryer. Failure to do so can result in fire, explosion,

or death.

• All connections must be in accordance with local codes and regulations. Failure to do so

can result in fire, explosion, or death.

• Gas dryers MUST exhaust to the outdoors. Failure to do so can result in fire, explosion, or

death.

Connecting the Gas Supply

O Make sure that the gas supply to the laundry

room is turned OFR Confirm that the type of gas available in your laundry room is

appropriate for the dryer. The dryer is prepared for Natural Gas with a 3/8-in. NPT

gas connection.

O Remove the shipping cap from the gas

connection at the back of the dryer. Be careful not to damage the threads of the gas

connector when removing the shipping cap.

O Connect the dryer to your laundry room's gas

supply using a new flexible stainless steel connector with a 3/8-in. NPT fitting.

O Securely all connections between the

dryer and your laundry room's gas supply.

Turn on your laundry room's gas supply and

check all pipe connections (both internal and external) for gas leaks with a noncorrosive

leak-detection fluid.

tighten

Electrical Connection

Plug dryer into a 120-VAC, 60-Hz.

grounded 3-prong outlet.

Flexible Connector

High-Altitude Installations

The BTU rating of this dryer is AGA-certified for elevations below 10,000 feet.

If your gas dryer is being installed at an elevation above 10,000 feet, it must be derated by a

qualified technician or gas supplier.

INSTALLATIONINST UCTIONS

CONNECTING ELECTRICDRYERS

&WAI:ININ6: To help prevent fire, electric shock, serious injury or death, the wiring and

grounding must conform to the latest edition of the National Electrical Code, ANSl/NFPA 70 and all applicable local regulations. Please contact a qualified electrician to check your home's wiring and

fuses to ensure that your home has adequate electrical power to operate the dryer.

Electrical Requirements for Electric Models Only

WARI ilI iG" Toreducetheriskoffire,electricshock,orinjurytopersonswhenusingthis

appliance, follow basic precautions, including the following:

This dryer must be connected to a grounded metal, permanent wiring system, or an equipment= rounding conductor must be run

with the circuit conductors and connected to the equipment=grounding terminal or lead

on the dryer. Failure to do so can result in fire, explosion, or death.

The dryer has its own terminal block that must be connected to a separate 240 VAC,

60-Hertz, single=phase circuit, fused at 30 amperes (the circuit must be fused on both

sides of the line). ELECTRICAL SERVICE FOR THE DRYER SHOULD BE OF THE

MAXIMUM RATE VOLTAGE LISTED ON THE NAMEPLATE. DO NOT CONNECT DRYER TO

110-, 115-, OR 120-VOLT CIRCUIT. Heating elements are available for field installation

in dryers which are to be connected to an electrical service of a different voltage than

that listed on the rating plate. Failure to follow these instructions can result in fire, explosion,

or death.

• If branch circuit to dryer is 15 ft. (4.5 m) or less in length, use UL (Underwriters Laboratories) listed No.-10 AWG wire

(copper wire only), or as required by local codes, if over 15 ft. (4.50 m), use UL=listed

No.=8 AWG wire (copper wire only), or as

required by local codes. Allow sufficient slack in wiring so dryer can be moved from

its normal location when necessary. Failure

to do so can result in fire, explosion, or death.

= The power cord (pigtail) connection between

wall receptacle and dryer terminal block IS NOT supplied with dryer. Type of pigtail

and gauge of wire must conform to local codes and with instructions on the following

pages. Failure to follow these instructions can result in fire, explosion, or death.

• A 4-wire connection is required for all mobile and manufactured home installations, as

well as all new construction after January 1, 1996. A 4=wire connection must be used

where local codes do not permit grounding through the neutral wire. Failure to do so can

result in fire, explosion, or death.

Special Electrical Requirements for Mobile or Manufactured Homes

&WARN|NG; To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Any installation in a manufactured or mobile • A 4=wire connection is required for all mobile home must comply with the Manufactured and manufactured home installations, as well

Home Construction and Safety Standards as all new construction after January 1, 1996. Title 24 CFR, Part 32-80 or Standard CAN/ Failure to do so can result in fire, explosion, or

CSA0Z240 MH and local codes and ordinances, death.

INSTALLATIONINSTRUCTIONS

SPECIAL REOUIREMENTS FOR MANUFACTURED OR MOBILE HOMES

Any installation in a manufactured or mobile home must comply with the Manufactured Home

Construction and Safety Standards Title 24 CFR,

Part 32-80 or Standard CAN/CSAOZ240 MH and

local codes and ordinances. If you are uncertain whether your proposed installation will comply

with these standards, please contact a service and installation professional for assistance.

• A gas dryer must be permanently attached to the floor.

The electrical connection for an electric dryer must be a 4-wire connection. More detailed

information concerning the electrical connection is provided in the section Connecting Electric

Dryers.

To reduce the risk of combustion and fire, the dryer must be vented to the outside.

DO NOT vent the dryer under a manufactured home or mobile home.

Electric dryers may be vented to the outside using the back, left, right, or bottom panel.

Gas dryers may be vented to the outside using the back, left, or bottom panel. Gas dryers may

not be vented to the outside using the right side panel because of the burner housing.

The dryer exhaust duct must be affixed securely to the manufactured or mobile home structure,

and the exhaust duct must be made of a material that will resist fire and combustion.

It is recommended that you use a rigid or flexible metal duct.

DO NOT connect the dryer exhaust duct to any other duct, vent, chimney, or other

exhaust duct. Make sure the dryer has adequate access to

outside fresh air to ensure proper operation. The opening for outside fresh air must be at

least 25 in2(163 cm2). It is important that the clearance of the duct

from any combustible construction be at least 2 in. (5cm), and when venting the dryer to

the outdoors, the dryer can be installed with a clearance of 1 in. (2.5 cm) at the sides and back

of the dryer. Please be aware that venting materials are

not supplied with the dryer. You should obtain the venting materials necessary for proper

installation.

FINAL iNSTALLATiON CHECK

Once you have completed the installation of the dryer and it is in its final location, confirm

proper operation with the following tests.

Testing Dryer Heating

GAS MODELS Close the dryer door, press the ON/OFF switch

to turn the dryer on, and start the dryer on a heat setting. When the dryer starts, the igniter should

ignite the main burner. NOTE: If all air is not purged from the gas line,

the gas igniter may turn off before the main burner ignites. Ifthis happens, the igniter will

reattempt gas ignition after approximately two minutes.

ELECTRIC MODELS

Close the dryer door, press the ON/OFF switch to turn the dryer on, and start the dryer on a heat

setting. The exhaust air should be warm after the dryer has been operating for 3 minutes.

Checking Airflow

Effective dryer operation requires proper airflow. The adequacy of the airflow can be measured

by evaluating the static pressure. Static pressure in the exhaust duct can be measured with

a manometer, placed on the exhaust duct approximately 2 ft. (60.9 cm) from the dryer.

Static pressure in the exhaust duct should not exceed 0.6 in. (1.5 cm). The dryer should be

checked while the dryer is running with no load.

Checking Levelness

Once the dryer is in its final location, recheck the dryer to be sure it is level. Make sure it is level front to back and side to side, and that

all 4 leveling feet are firmly on the floor.

iNSTALLATIONINST UCTIONS

DUCT CONDITION TESTING

Your dryer features FIowSense TM, an innovative sensor system that automatically detects

blockages and restrictions in dryer ductwork.

Keeping ductwork clean of lint build-up and free

of restrictions allows clothes to dry faster, reduces energy use, and helps prevent fires.

When the dryer is first installed, the duct condition test must be performed. This alerts you to any

existing problems before the dryer is used. The dryer also saves this information to compare and measure future changes.

To activate the duct condition test cycle: O Press and hold the DAMP DRY BEEP and

TEMP CONTROL buttons at the same time. While holding these buttons, press POWER

ON/OFR

O The dryer will show InS in the number display

to indicate that it is in duct condition testing mode.

O Press START/PAUSE. The dryer win run for

approximately 2 minutes to test for blockages or restrictions to air

flow in the ductwork.

Correct Venting

:TcJ

Restricted or Blocked Airflow

Avoid long runs or runs with multiple elbows

or bends.

If no bars are shown in the display, the ductwork is free from blockages or

restrictions.

If all bars are Nt,the dryer ductwork

has a blockage that needs to be removed immediately.

0 %...................................................................................................................................................................................................................................................................................................................................................................._J

Check for blockages and lint buildup.

Make sure the ductwork is not crushed or restricted.

SORTING LOADS

OWTO USE

Fabric care Labels

Most articles of clothing feature fabric care labels

that include instructions for proper care.

Grouping Similar Items

For best results, sort clothes into loads that can be dried with the same drying cycle.

Different fabrics have different care requirements,

and some fabrics will dry

more quickly than others.

f careLa els

Tumble

dry

Heat (_) (_ Q O setting

Dry Normal Permanent Press/

Gentle/ DonottumNedry (usedwith

delicate do notwash}

wrinkle resistant

Donot dry

LOADING THE DRYER

WARNING: To reduce the risk of fire, electric shock, or injury to persons when using this

appliance, follow basic precautions, including the following:

• Check all pockets to make sure that they are empty. Items such as clips, pens, coins, and

keys can damage both your dryer and your clothes. Flammable objects such as lighters

or matches could ignite, causing a fire. Failure to do so can result in fire, explosion, or

death.

• Never dry clothes that have been exposed to oil, gasoline, or other flammable substances.

washing clothes will not completely remove oil residues. Failure to obey this warning can

result in fire, explosion, or death.

• Combine large and small items in a load.

• Damp clothes will expand as they dry. Do not

overload the dryer; clothes require room to tumble to dry properly.

• Close zippers, hooks, and drawstrings to prevent these items from snagging or tangling

on other clothes.

CHECK THE LINT FILTER BEFORE EVERY LOAD

The CHECK FILTER indicator will light before

each load to remind you to make sure the lint filter is clean before starting a

new load. It will also come on during a load if the lint filter is clogged to let

you know that the lint filter needs to be cleaned; a clogged lint filter will increase drying times.

To clean, pull the lint filter straight up and roll any lint off the filter with your fingers. Do not rinse or

wash the filter to remove lint. Push the lint filter firmly back into place. See "Care and Cleaning"

for more information. Always ensure the lint filter is properly installed

before running the dryer. Running the dryer with a loose or missing lint filter may damage the

dryer and articles in the dryer.

f ........................................................................................................................................... %

Lint Filter

OWTO USE

CONTROL PANEL FEATURES

Following are instructions for starting and using your new dryer. Please refer to specific sections

of this manual for more detailed information. Important warning: TO reduce the risk of fire, electric shock, or injury to persons, read this entire manual, including the Important Safety

Instructions, before operating this dryer.

POWER ON/OFF BUTTON

Press to turn the dryer ON. Press again to

turn the dryer OFR

NOTE: Pressing the ON/OFF button during a cycle will cancel that cycle and any load

settings will be lost.

CYCLE SELECTOR KNOB

Turn this knob to select the desired cycle. Once the desired cycle has been selected,

the standard presets will be shown in the display. On MANUAL DRY cycles, these

settings can be adjusted using the cycle settings buttons anytime before starting

the cycle.

START/PAUSE BUTTON

Press this button to START the selected

cycle. If the dryer is running, use this button to PAUSE the cycle without losing the

current settings. NOTE: If you do not press the START/PAUSE

button to resume a cycle within 8 minutes, the dryer automatically turns off.

O CYCLE SETTING BUTTONS

Use these buttons to adjust the desired cycle

settings for the selected cycle.

TiME AND STATUS DISPLAY

The display shows the settings, estimated time remaining, options, and status messages

for your dryer.

OPTION BUTTONS

The option buttons allow you to select additional cycle options. Certain buttons

also allow you to activate special functions by pressing and holding the button for

3 seconds. For detailed information about the individual

options, please see the following pages.

MORE TIME/LESS TIME BUTTONS

Use these buttons with MANUAL DRY and

TIME DRY cycles to adjust the drying time.

Press the MORE TIME button to increase

the selected manual cycle time by a minute;

press LESS TIME to decrease the cycle time by a minute.

OWTO USE

CYCLE GUIDE

The cycle guide below shows the options and recommended fabric types for each cycle.

HeavyDub]

Co,on/ Towels

Normal

Perm,Press

Delicates

Ultra Delicate

Speed Dry

Jeans, heavyweightitems

Denims,towels, heavycottons

Workclothes, corduroys,etc.

Permanentpress, syntheticitems

Lingerie,sheets, blouses

Workoutwear, sheeror lacy

garments

Forsmallloads with short

dryingtimes

Normal

Adjustable

Normal

Adjustable

Normal

Adjustable

Normal

Adjustable

Normal

Adjustable

Normal

Adjustable

Off

High

Med.High

Medium

High

Low

UltraLow

High

Adjustable

FreshenUp

Air Dry

Time Dry

Forremoving lightwrinkles

fromclothing

Foritemsthat requireheat-free

dryingsuchas plasticsor rubber

Forgeneraldrying; time,temperature,

andoptionscan be setmanually

Off

High

Adjustable

NoHeat

High

Adjustable

Sensor Dry Cycles

Sensor Dry cycles utilize LG's unique dual sensor system to detect and compare the moisture level

in clothes and in the air and adjust the drying time as needed to ensure superior results. The

dryer automatically sets the dryness level and temperature at the recommended setting for each

cycle. The estimated time remaining will

Adjustable

Manual Dry Cycles

Use Manual Dry cycles to select a specific amount of drying time and a drying temperature.

When a Manual Dry cycle is selected, the ESTIMATED TIME REMAINING display shows

the actual time remaining in your cycle. You can

change the actual time in the cycle by pressing MORE TIME or LESS TIME.

be shown in the display. NOTE: To protect your garments, not every dry level, temperature, or option is available

with every cycle.

OWTO USE

THE TIME AND STATUS DISPLAY

The display shows the settings, estimated time remaining, options, and status messages for your dryer.

_]_ ESTIMATED TiME REMAiNiNG

When the START/PAUSE button is pressed, the display will indicate the estimated time

remaining for the selected drying cycle.

CYCLE COMPLETION INDICATOR WITH

CHECK RLTER REMINDER

This portion of the display shows which

stage of the drying cycle is currently underway (CHECK FILTER, DRYING,

COOLING, or WRINKLE CARE).

CHILD LOCK INDEATOR

When CHILD LOCK is set, the Child Lock indicator will appear and all buttons are

disabled except the ON/OFF button. This prevents children from changing settings while the dryer is operating.

LINT FETER INDICATOR

The dryer automatically detects reduced air

flow caused by a full lint filter. The CHECK FILTER indicator will light

before each load as a reminder to check the lint filter before starting

each load. If the lint filter becomes clogged during a load, the indicator will come on to

let you know that the filter should be cleaned immediately for maximum efficiency.

Always clean the lint filter before every cycle.

FLOW SENSE TM DUCT BLOCKAGE

SENSING SYSTEM INDICATOR

The FLOW SENSE TM duct blockage sensing system detects and alerts you to blockages

in the ductwork that reduce exhaust flow

from the dryer. This not only helps prevent fires and save lives, it can improve operating

efficiency and help minimize service calls, saving you money.

display, the ductwork is free from

lf no bars are shown in the

blockages.

greater the blockage. The more bars displayed, the

If all bars are lit, the dryer

ductwork has a blockage that

needs to be removed immediately.

+ 56 hidden pages