rights reserved. LG and the LG logo are
registered trademarks of LG Group and its
related entities. All other trademarks are
the property of their respective owners.
Contents
Contents ..........................2
Safety ............................5
Your Phone .......................24
Phone Components ......................24
Rear view .............................26
Getting Started ....................27
Installing the SIM card and battery. . . . . . . . . . 27
TIA(Telecommunications
Industry Association) Safety
Information
The following is the complete TIA Safety
Information for wireless handheld phones.
Exposure to Radio Frequency Signal
Your wireless handheld portable phone is
a low power radio transmitter and receiver.
When it is ON, it receives and also sends
out Radio Frequency (RF) signals. In
August, 1996, the Federal Communications
Commissions (FCC) adopted RF exposure
guidelines with safety levels for handheld
wireless phones. Those guidelines are
consistent with the safety standards
previously set by both U.S. and international
standards bodies:
Ź
ANSI C95.1 (1992) *
Ź
NCRP Report 86 (1986)
Ź
ICNIRP (1996)
Ź
Health Canada, Safety Code 6, 1999.
Those standards were based on
comprehensive and periodic evaluations
of the relevant scientific literature. For
example, over 120 scientists, engineers, and
physicians from universities, government
health agencies, and industry reviewed the
available body of research to develop the
ANSI Standard (C95.1). The design of your
phone complies with the FCC guidelines, IC
Regulations (and those standards).
Antenna Care
Use only the supplied or an approved
replacement antenna.
Unauthorised antennas, modifications, or
attachments could damage the phone and
may violate FCC regulations.
Phone Operation
NORMAL POSITION: Hold the phone as you
would any other telephone with the antenna
pointed up and over your shoulder.
5
Safety
Tips on Efficient Operation
For your phone to operate most efficiently:
Do not touch the antenna unnecessarily
when the phone is in use.
Contact with the antenna affects call quality
and may cause the phone to operate at a
higher power level than otherwise needed.
Driving
Check the laws and regulations on the use
of wireless phones in the areas where you
drive and always obey them. Also, if using
your phone while driving, please observe the
following:
Ź
Give full attention to driving -- driving
safely is your first responsibility;
Ź
Use hands-free operation.
Electronic Devices
Most modern electronic equipment is
shielded from RF signals. However, certain
electronic equipment may not be shielded
against the RF signals from your wireless
phone.
6
Pacemakers
The Health Industry Manufacturers
Association recommends that a minimum
separation of six (6”) inches be maintained
between a handheld wireless phone and a
pacemaker to avoid potential interference
with the pacemaker. These recommendations
are consistent with the independent research
by and recommendations of Wireless
Technology Research.
Persons with Pacemakers
Ź
Should ALWAYS keep the phone more
than six inches from their pacemaker
when the phone is turned ON;
Ź
Should not carry the phone in a breast
pocket;
Ź
Should use the ear opposite the
pacemaker to minimize the potential for
interference;
Ź
Should turn the phone OFF immediately
if there is any reason to suspect that
interference is taking place.
Hearing Aids
Some digital wireless phones may interfere
with some hearing aids. In the event of such
interference, you may want to consult your
service provider (or call the customer service
line to discuss alternatives.) Optional for
each phone manufacturer.
Other Medical Devices
If you use any other personal medical device,
consult the manufacturer of your device
to determine if it is adequately shielded
from external RF energy. Your physician
may be able to assist you in obtaining this
information.
Health Care Facilities
Turn your phone OFF in health care facilities
when any regulations posted in these areas
instruct you to do so. Hospitals or health
care facilities may use equipment that could
be sensitive to external RF energy.
Vehicles
RF signals may affect improperly installed or
inadequately shielded electronic systems in
motor vehicles. Check with the manufacturer
or its representative regarding your vehicle.
You should also consult the manufacturer
of any equipment that has been added to
your vehicle.
Posted Facilities
Turn your phone OFF in any facility where
posted notices so require.
Aircraft
FCC and Transport Canada regulations
prohibit using your phone while in the air.
Switch OFF your phone before boarding an
aircraft.
Blasting Areas
To avoid interfering with blasting operations,
turn your phone OFF when in a “blasting
area” or in areas posted: “Turn off two-way
radio”. Obey all signs and instructions.
7
Safety
Potentially Explosive
Atmosphere
Turn your phone OFF when in any area
with a potentially explosive atmosphere and
obey all signs and instructions. Sparks in
such areas could cause an explosion or fire
resulting in bodily injury or even death.
Areas with a potentially explosive
atmosphere are often, but not always
marked clearly. Potential areas may include:
fueling areas (such as gasoline stations);
below deck on boats; fuel or chemical
transfer or storage facilities; vehicles using
liquefied petroleum gas (such as propane
or butane); areas where the air contains
chemicals or particles (such as grain, dust,
or metal powders); and any other area where
you would normally be advised to turn off
your vehicle engine.
8
For Vehicles Equipped with an
Air Bag
An air bag inflates with great force. DO NOT
place objects, including either installed or
portable wireless equipment, in the area
over the air bag or in the air bag deployment
area. If in-vehicle wireless equipment is
improperly installed and the air bag inflates,
serious injury could result.
Charger and Adapter Safety
Ź
The charger and adapter are intended for
indoor use only.
Ź
Do not expose the battery charger or
adapter to direct sunlight or use it in
places with high humidity, such as a
bathroom.
Battery Information and Care
Ź
Please dispose of your battery properly
or take it to your local wireless carrier for
recycling.
Ź
Do not dispose of your battery by fire or
with hazardous or flammable materials.
Ź
Never use an unapproved battery since
this could damage the phone and/or
battery and could cause the battery to
explode.
Ź
The battery does not need to be fully
discharged before recharging.
Ź
Use only LG-approved chargers specific
to your phone model since they are
designed to maximize battery life.
Ź
Do not disassemble or short-circuit the
battery.
Ź
Keep the battery’s metal contacts clean.
Ź
Replace the battery when it no longer
provides acceptable performance. The
battery can be recharged several hundred
times before replacement.
Ź
Recharge the battery after long periods of
non-use to maximize battery life.
Ź
Battery life will vary due to usage patterns
and environmental conditions.
Ź
Use of extended backlighting,
MiniBrowser, and data connectivity kits
affect battery life and talk/standby times.
Safety Information
Please read and observe the following
information for safe and proper use of your
phone and to prevent damage. Also, keep
the user’s guide in an accessible place at all
the times after reading it.
Explosion, Shock, and Fire
Hazards
Ź
Unplug the power cord and charger
during lightning storms to avoid electric
shock or fire.
Ź
Make sure that no sharp-edged items
such as animal’s teeth, nails, come into
contact with the battery. There is a risk of
this causing a fire.
Ź
Do not use harsh chemicals(such as
alcohol, benzene, thinners, etc.) or
detergents to clean your phone. There is
a risk of this causing a fire.
Ź
Do not handle the phone with wet hands
while it is being charged. It may cause
an electric shock or seriously damage
your phone.
9
Safety
Ź
Do not drop, strike, or shake your phone
severely. Such actions may harm the
internal circuit boards of the phone.
Ź
Do not put your phone in a place subject
to excessive dust and keep the minimum
required distance between the power
cord and heat sources.
Ź
Unplug the power cord prior to cleaning
your phone, and clean the power plug pin
when it is dirty.
Ź
Do not damage the power cord by
bending, twisting, pulling, or heating. Do
not use the plug if it is loose as it may
cause a fire or electric shock.
Ź
When using the power plug, ensure that
it is firmly connected. If it is not, it may
cause excessive heat or fire.
Ź
Do not place any heavy items on the
power cord. Do not allow the power cord
to be crimped as it may cause fire or
electric shock.
Ź
Do not disassemble the phone.
10
Ź
Do not place or answer calls while
charging the phone as it may short-circuit
the phone and/or cause electric shock
or fire.
Ź
If you put your phone in a pocket or bag
without covering the receptacle of the
phone (power plug pin), metallic articles
(such as a coin, paperclip or pen) may
short-circuit the phone. Always cover the
receptacle when not in use.
Ź
Do not short-circuit the battery. Metallic
articles such as a coin, paperclip or pen
in your pocket or bag may short-circuit
the + and – terminals of the battery
(metal strips on the battery) upon
moving. Short-circuiting of the terminal
may damage the battery and cause an
explosion.
Ź
Never place your phone in a microwave
oven as it will cause the battery to
explode.
General Warnings and Cau tions
Ź
Only use the batteries, antennas, and
chargers provided by LG. The warranty
will not be applied to products provided
by other suppliers.
Ź
Store the battery in a place out of reach
of children.
Ź
Using a damaged battery or placing a
battery in your mouth may cause serious
injury.
Ź
Do not place items containing magnetic
components such as a credit card, phone
card, bank book or subway ticket near
your phone. The magnetism of the phone
may damage the data stored in the
magnetic strip.
Ź
Do not hold or let the antenna come in
contact with your body during a call.
Ź
Talking on your phone for a long period of
time may reduce call quality due to heat
generated during use.
Ź
When the phone is not used for a long
period time, store it in a safe place with
the power cord unplugged.
Ź
Using the phone in proximity to receiving
equipment (i.e., TV or radio) may cause
interference to the phone.
Ź
Only authorized personnel should service
the phone and its accessories. Faulty
installation or service may result in
accidents and consequently invalidate the
warranty.
Ź
Do not use the phone if the antenna is
damaged. If a damaged antenna contacts
skin, it may cause a slight burn. Please
contact an LG Authorized Service Center
to replace the damaged antenna.
Ź
Do not use the phone in areas where its
use is prohibited. (For example: aircraft)
Ź
Do not immerse your phone in water. If
this happens, turn it off immediately and
remove the battery. If the phone does not
work, take it to an LG Authorized Service
Center.
Ź
Use accessories, such as earphones and
headsets, with caution. Ensure that cables
are tucked away safely and do not touch
the antenna unnecessarily.
11
Safety
Warning! Important Safety
Information
Avoiding hearing damage
Ź
Permanent hearing loss may occur if
you use your phone and/or headset at
a high volume. Set the volume to a safe
level. You can adapt over time to a higher
volume of sound that may sound normal
but can be damaging to your hearing. If
you experience ringing in your ears or
muffled speech, stop listening and have
your hearing checked. The louder the
volume, the less time is required before
your hearing could be affected. Hearing
experts suggest that to protect your
hearing:
Ź
Limit the amount of time you use your
phone and/or headset at high volume.
Ź
Avoid turning up the volume to block out
noisy surroundings.
12
Ź
Turn the volume down if you can’t hear
people speaking near you. For information
about how to set a maximum volume limit
on your phone, see the features guide for
your phone.
Using your phone safely
Use of your phone while operating a vehicle
is not recommended and is illegal in some
areas. Be careful and attentive while driving.
Stop using your phone if you find it disruptive
or distracting while operating any type of
vehicle or performing any other activity that
requires your full attention.
FDA Consumer Update
The U.S. Food and Drug Administration’s
Center for Devices and Radiological Health
Consumer Update on Mobile Phones:
1. Do wireless phones pose a health
hazard?
The available scientific evidence does
not show that any health problems are
associated with using wireless phones. There
is no proof, however, that wireless phones
are absolutely safe. Wireless phones emit
low levels of radiofrequency energy (RF)
in the microwave range while being used.
They also emit very low levels of RF when
in the Main Menu Screen. Whereas high
levels of RF can produce health effects
(by heating tissue), exposure to low level
RF that does not produce heating effects
causes no known adverse health effects.
Many studies of low level RF exposures
have not found any biological effects. Some
studies have suggested that some biological
effects may occur, but such findings have
not been confirmed by additional research.
In some cases, other researchers have had
difficulty in reproducing those studies, or
in determining the reasons for inconsistent
results.
2. What is the FDA's role concerning the
safety of wireless phones?
Under the law, the FDA does not review
the safety of radiationemitting consumer
products such as wireless phones before
they can be sold, as it does with new drugs
or medical devices. However, the agency has
authority to take action if wireless phones
are shown to emit radiofrequency energy
(RF) at a level that is hazardous to the user.
In such a case, the FDA could require the
manufacturers of wireless phones to notify
users of the health hazard and to repair,
replace or recall the phones so that the
hazard no longer exists.
Although the existing scientific data does not
justify FDA regulatory actions, the FDA has
urged the wireless phone industry to take a
number of steps, including the following:
Ź
Support needed research into possible
biological effects of RF of the type emitted
by wireless phones.
Ź
Design wireless phones in a way that
minimizes any RF exposure to the user
that is not necessary for device function;
and cooperate in providing users of
wireless phones with the best possible
information on possible effects of wireless
phone use on human health.
The FDA belongs to an interagency working
group of the federal agencies that have
responsibility for different aspects of RF
13
Safety
safety to ensure coordinated efforts at the
federal level. The following agencies belong
to this working group:
Ź
National Institute for Occupational Safety
and Health.
Ź
Environmental Protection Agency.
Ź
Occupational Safety and Health
Administration.
Ź
National Telecommunications and
Information Administration.
The National Institutes of Health participates
in some interagency working group
activities, as well. The FDA shares regulatory
responsibilities for wireless phones with the
Federal Communications Commission (FCC).
All phones that are sold in the United States
must comply with FCC safety guidelines that
limit RF exposure. The FCC relies on the
FDA and other health agencies for safety
questions about wireless phones. The FCC
also regulates the base stations that the
wireless phone networks rely upon. While
these base stations operate at higher power
than the wireless phones themselves do,
the RF exposures that people get from these
14
base stations are typically thousands of
times lower than those they can get from
wireless phones. Base stations are thus not
the subject of the safety questions discussed
in this document.
3. What kinds of phones are the subject
of this update?
The term “wireless phone” refers here to
handheld wireless phones with built-in
antennas, often called “cell”, “mobile”, or
“PCS” phones. These types of wireless
phones can expose the user to measurable
radiofrequency energy (RF) because of
the short distance between the phone and
the user’s head. These RF exposures are
limited by FCC safety guidelines that were
developed with the advice of the FDA and
other federal health and safety agencies.
When the phone is located at greater
distances from the user, the exposure to RF
is drastically lower because a person's RF
exposure decreases rapidly with increasing
distance from the source. The so called
“cordless phones,” which have a base unit
connected to the telephone wiring in a
house, typically operate at far lower power
levels, and thus produce RF exposures far
below the FCC safety limits.
4. What are the results of the research
done already?
The research done thus far has produced
conflicting results, and many studies
have suffered from flaws in their research
methods.
Animal experiments investigating the effects
of radiofrequency energy (RF) exposures
characteristic of wireless phones have
yielded conflicting results that often cannot
be repeated in other laboratories. A few
animal studies, however, have suggested
that low levels of RF could accelerate the
development of cancer in laboratory animals.
However, many of the studies that showed
increased tumor development used animals
that had been genetically engineered or
treated with cancer-causing chemicals so
as to be pre-disposed to develop cancer
in the absence of RF exposure. Other
studies exposed the animals to RF for up
to 22 hours per day. These conditions are
not similar to the conditions under which
people use wireless phones, so we don’t
know with certainty what the results of such
studies mean for human health. Three large
epidemiology studies have been published
since December 2000. Between them, the
studies investigated any possible association
between the use of wireless phones and
primary brain cancer, glioma, meningioma,
or acoustic neuroma, tumors of the brain or
salivary gland, leukemia, or other cancers.
None of the studies demonstrated the
existence of any harmful health effects from
wireless phone RF exposures.
However, none of the studies can answer
questions about long-term exposures, since
the average period of phone use in these
studies was around three years.
5. What research is needed to decide
whether RF exposure from wireless
phones poses a health risk?
A combination of laboratory studies and
epidemiological studies of people actually
using wireless phones would provide some
of the data that is needed. Lifetime animal
15
Safety
exposure studies could be completed in a
few years. However, very large numbers of
animals would be needed to provide reliable
proof of a cancer promoting effect, if one
exists. Epidemiological studies can provide
data that is directly applicable to human
populations, but 10 or more years follow-up
may be needed to provide answers about
some health effects, such as cancer. This
is because the interval between the time of
exposure to a cancer-causing agent and the
time tumors develop — if they do — may
be many, many years. The interpretation
of epidemiological studies is hampered by
difficulties in measuring actual RF exposure
during day-to-day use of wireless phones.
Many factors affect this measurement, such
as the angle at which the phone is held, or
which model of phone is used.
6. What is the FDA doing to find out
more about the possible health
effects of wireless phone RF?
The FDA is working with the U.S. National
Toxicology Program and with groups of
investigators around the world to ensure that
16
high priority animal studies are conducted
to address important questions about the
effects of exposure to radio frequency energy
(RF). The FDA has been a leading participant
in the World Health Organization International
Electromagnetic Fields (EMF) Project since
its inception in 1996. An influential result
of this work has been the development of a
detailed agenda of research needs that has
driven the establishment of new research
programs around the world. The project
has also helped develop a series of public
information documents on EMF issues. The
FDA and the Cellular Telecommunications
& Internet Association (CTIA) have a formal
Cooperative Research and Development
Agreement (CRADA) to do research on
wireless phone safety. The FDA provides
the scientific oversight, obtaining input
from experts in government, industry, and
academic organizations. CTIA-funded
research is conducted through contracts
with independent investigators. The initial
research will include both laboratory studies
and studies of wireless phone users. The
CRADA will also include a broad assessment
of additional research needs in the context
of the latest research developments around
the world.
7. How can I find out how much radio
frequency energy exposure I can get
by using my wireless phone?
All phones sold in the United States must
comply with Federal Communications
Commission (FCC) guidelines that limit
radio frequency energy (RF) exposures.
The FCC established these guidelines in
consultation with the FDA and the other
federal health and safety agencies. The
FCC limit for RF exposure from wireless
telephones is set at a Specific Absorption
Rate (SAR) of 1.6 watts per kilogram (1.6
W/kg). The FCC limit is consistent with the
safety standards developed by the Institute
of Electrical and Electronic Engineering
(IEEE) and the National Council on Radiation
Protection and Measurement. The exposure
limit takes into consideration the body’s
ability to remove heat from the tissues that
absorb energy from the wireless phone
and is set well below levels known to have
effects. Manufacturers of wireless phones
must report the RF exposure level for each
model of phone to the FCC. The FCC website
(http://www.fcc.gov/oet/rfsafety) gives
directions for locating the FCC identification
number on your phone so you can find your
phone’s RF exposure level in the online
listing.
8. What has the FDA done to measure
the radio frequency energy coming
from wireless phones?
The Institute of Electrical and Electronic
Engineers (IEEE) is developing a technical
standard for measuring the radio frequency
energy (RF) exposure from wireless
phones and other wireless handsets with
the participation and leadership of FDA
scientists and engineers. The standard,
“Recommended Practice for Determining
the Spatial-Peak Specific Absorption Rate
(SAR) in the Human Body Due to Wireless
Communications Devices: Experimental
Techniques,” sets forth the first consistent
test methodology for measuring the rate
at which RF is deposited in the heads of
wireless phone users.
17
Safety
The test method uses a tissue-simulating
model of the human head. Standardized
SAR test methodology is expected to greatly
improve the consistency of measurements
made at different laboratories on the
same phone. SAR is the measurement of
the amount of energy absorbed in tissue,
either by the whole body or a small part
of the body. It is measured in watts/kg (or
milliwatts/g) of matter. This measurement is
used to determine whether a wireless phone
complies with safety guidelines.
9. What steps can I take to reduce my
exposure to radio frequency energy
from my wireless phone?
If there is a risk from these products — and
at this point we do not know that there
is — it is probably very small. But if you are
concerned about avoiding even potential
risks, you can take a few simple steps to
minimize your exposure to radio frequency
energy (RF). Since time is a key factor in
how much exposure a person receives,
reducing the amount of time spent using a
wireless phone will reduce RF exposure. If
18
you must conduct extended conversations
by wireless phone every day, you could place
more distance between your body and the
source of the RF, since the exposure level
drops off dramatically with distance. For
example, you could use a headset and carry
the wireless phone away from your body or
use a wireless phone connected to a remote
antenna. Again, the scientific data does
not demonstrate that wireless phones are
harmful. But if you are concerned about the
RF exposure from these products, you can
use measures like those described above
to reduce your RF exposure from wireless
phone use.
10. What about children using wireless
phones?
The scientific evidence does not show
a danger to users of wireless phones,
including children and teenagers. If you
want to take steps to lower exposure to
radio frequency energy (RF), the measures
described above would apply to children
and teenagers using wireless phones.
Reducing the time of wireless phone use
and increasing the distance between the
user and the RF source will reduce RF
exposure. Some groups sponsored by other
national governments have advised that
children be discouraged from using wireless
phones at all. For example, the government
in the United Kingdom distributed leaflets
containing such a recommendation in
December 2000. They noted that no
evidence exists that using a wireless phone
causes brain tumors or other ill effects. Their
recommendation to limit wireless phone use
by children was strictly precautionary; it was
not based on scientific evidence that any
health hazard exists.
11. What about wireless phone
interference with medical
equipment?
Radio frequency energy (RF) from wireless
phones can interact with some electronic
devices. For this reason, the FDA helped
develop a detailed test method to measure
electromagnetic interference (EMI) of
implanted cardiac pacemakers and
defibrillators from wireless telephones.
This test method is now part of a standard
sponsored by the Association for the
Advancement of Medical instrumentation
(AAMI). The final draft, a joint effort by the
FDA, medical device manufacturers, and
many other groups, was completed in late
2000. This standard will allow manufacturers
to ensure that cardiac pacemakers and
defibrillators are safe from wireless phone
EMI. The FDA has tested hearing aids for
interference from handheld wireless phones
and helped develop a voluntary standard
sponsored by the Institute of Electrical and
Electronic Engineers (IEEE). This standard
specifies test methods and performance
requirements for hearing aids and wireless
phones so that no interference occurs when
a person uses a “compatible” phone and a
“compatible” hearing aid at the same time.
This standard was approved by the IEEE in
2000. The FDA continues to monitor the use
of wireless phones for possible interactions
with other medical devices. Should harmful
interference be found to occur, the FDA will
conduct testing to assess the interference
and work to resolve the problem.
19
Safety
12. Where can I find additional
information?
For additional information, please refer to
the following resources: FDA web page
on wireless phones (http://www.fda.gov/)
Federal Communications Commission (FCC)
RF Safety Program (http://www.fcc.gov/
oet/rfsafety) International Commission on
Non-lonizing Radiation Protection (http://
www.icnirp.de) World Health Organization
(WHO) International EMF Project (http://www.
who.int/peh-emf/en/) National Radiological
Protection Board (UK) (http://www.hpa.org.
uk/radiation/)
Consumer Information on SAR
(Specific Absorption Rate)
This Model Phone Meets the Government’s
Requirements for Exposure to Radio
Waves. Your wireless phone is a radio
transmitter and receiver. It is designed and
manufactured not to exceed the emission
limits for exposure to radio frequency (RF)
energy set by the Federal Communications
Commission of the U.S. Government. These
20
limits are part of comprehensive guidelines
and establish permitted levels of RF energy
for the general population. The guidelines
are based on standards that were developed
by independent scientific organizations
through periodic and thorough evaluation of
scientific studies. The standards include a
substantial safety margin designed to assure
the safety of all persons, regardless of age
and health.
The exposure standard for wireless mobile
phones employs a unit of measurement
known as the Specific Absorption Rate, or
SAR. The SAR limit set by the FCC/IC is
1.6 W/kg*. Tests for SAR are conducted
using standard operating positions specified
by the FCC with the phone transmitting
at its highest certified power level in all
tested frequency bands. Although SAR is
determined at the highest certified power
level, the actual SAR level of the phone while
operating can be well below the maximum
value. Because the phone is designed to
operate at multiple power levels to use only
the power required to reach the network,
in general, the closer you are to a wireless
base station antenna, the lower the power
output.
Before a phone model is available for sale
to the public, it must be tested and certified
to the FCC that it does not exceed the limit
established by the government-adopted
requirement for safe exposure. The tests are
performed in positions and locations (e.g., at
the ear and worn on the body) as required
by the FCC for each model.
The highest SAR value for this model
phone when tested for use at the ear is
0.77 W/kg and when worn on the body,
as described in this user guide, is 0.58 W/
kg (body-worn measurements differ among
phone models, depending upon available
accessories and FCC/IC requirements).
While there may be differences between
SAR levels of various phones and at various
positions, they all meet the government
requirement for safe exposure. The FCC has
granted an Equipment Authorization for this
model phone with all reported SAR levels
evaluated as in compliance with the FCC
RF emission guidelines. SAR information
on this model phone is on file with the FCC
and can be found under the Display Grant
section of http://www. fcc.gov/oet/ea/fccid
after searching on FCC ID: ZNFLG440G
Additional information on Specific Absorption
Rates (SAR) can be found on the Cellular
Telecommunications Industry Association
(CTIA) website at http://www.ctia.org/
* In the United States and Canada, the
SAR limit for mobile phones used by the
public is 1.6 watts/kg (W/kg) averaged
over one gram of tissue. The standard
incorporates a substantial margin of
safety to give additional protection for the
public and to account for any variations in
measurements.
* Product meets current FCC & IC Radio
Frequency Exposure Guidelines.
FCC ID: ZNFLG440G
IC ID: 2703C-C440
21
Safety
Body-worn Operation
This device was tested for typical body-worn
operations with the back of the phone kept
1.5 cm (0.59 inches) between the user’s
body and the back of the phone. To comply
with FCC RF exposure requirements, a
minimum separation distance of 1.5 cm
(0.59 inches) must be maintained between
the user's body and the back of the phone.
Third-party belt-clips, holsters, and similar
accessories containing metallic components
may not be used. Body-worn accessories
that cannot maintain 1.5 cm (0.59 inches)
separation distance between the user's body
and the back of the phone, and have not
been tested for typical bodyworn operations
may not comply with FCC RF exposure limits
and should be avoided.
22
FCC Part 15.19 statemnet
This device complies with part 15 of FCC
rules and ICES-003 Class B digital apparatus
requirements for Industry Canada. Operation
is subject to the following two conditions:(1)
This device may not cause harmful
interference, and (2) this device must
accept any interference received, including
interference that may cause undesired
operation.
Part 15.21 statement
Change or Modifications that are not
expressly approved by the manufacturer
could void the user's authority to operate the
equipment.
Part 15.105 statement
This equipment has been tested and found
to comply with the limits for a class B digital
device, pursuant to Part 15 of the FCC
Rules.
These limits are designed to provide
reasonable protection against harmful
interference in a residential installation.
This equipment generates uses and can
radiate radio frequency energy and, if not
installed and used in accordance with the
instructions, may cause harmful interference
to radio communications. However, there
is no guarantee that interference will not
occur in a particular installation. If this
equipment does cause harmful interference
to radio or television reception, which can
be determined by turning the equipment
off and on, the user is encouraged to try to
correct the interference by one or more of
the following measures:
Ź
Reorient or relocate the receiving
antenna.
Ź
Increase the separation between the
equipment and receiver.
Ź
Connect the equipment into an outlet on
a circuit different from that to which the
receiver is connected.
Ź
Consult the dealer or an experienced
radio/TV technician for help.
This device complies with Industry Canada
licence-exempt RSS standard(s). Operation
is subject to the following two conditions: (1)
this device may not cause interference, and
(2) this device must accept any interference,
including interference that may cause
undesired operation of the device.
Ambient temperatures
Max: +50°C (discharging),
+45°C (charging)
Min: -10°C
WCDMA 850/1900 MHz
GSM 850/900/1800/1900 MHz
23
Your Phone
Phone Components
1
2
3
4
5
6
7
Press and hold to activate/
deactivate Vibrating Mode.
24
8
9
10
11
12
13
1. Earpiece: Lets you hear the caller during
a call.
2. Main LCD: Displays phone status icons,
menu items, web items, web information,
pictures and more, in full colour.
3. Left Soft Key/Right Soft Key: Each of
these keys perform the functions indicated
by the text on the display immediately
above them.
4. Camera Key: Lets you activate the
Camera and take pictures.
5. Message Hot Key: Trigger this key to
directly go to Create Message.
6. Navigation Keys
Home screen functions:
Games & Apps
Contact List
Alarm Clock
Music
- In a menu: Navigates between menus.
7. Send Key: Press this key in standby
mode to quickly access the most recent
missed, dialed, and received calls. Also
dials a call when you enter a number.
8. Clear/Back Key: Allows you to return
to the previous screen. Press and hold to
activate the Voice Command function.
9. TTS Mode Key: Lets you turn the TTS
mode on/off.
10. OK Key: Select options and menus.
11. End/Power Key: Allows you to power
the phone on or off, end calls, or return
to standby mode.
12. Volume Keys: Allows you to control the
Master Volume while in standby mode
as well as the earpiece volume during
a call.
13. Charger/USB Port: Allows you to
connect a charger or other supported
accessories.
25
Your Phone
Rear view
Back Cover
SIM Card Slot
26
Battery
Getting Started
Installing the SIM card and
battery
1. Remove the back cover
Place your thumb at the top part of the
back cover and slide it downwards to
remove it.
2. Remove the battery
Hold the top edge of the phone and use
the fingernail cutout near the bottom of
the battery to lift the battery from the
phone.
Warning
Do not remove the battery when the
phone is turned on; this can damage the
phone.
27
Getting Started
3. Install the SIM card
Slide the SIM card into the SIM card slot
(as shown below). Make sure that the
gold contact area on the card is facing
downwards. To remove the SIM card, pull
it gently in the opposite direction.
28
4. Install the battery
Insert the top of the battery first into the
top edge of the battery compartment.
Ensure that the battery contacts align with
the terminals on the phone. Press the
bottom of the battery down until it snaps
into place.
5. Install the back cover
Align the back cover on the battery
compartment and slide it upwards until it
locks into place.
Loading...
+ 137 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.