LG BH7240B-DT, BH7540T User Manual

OWNER’S MANUAL

3D Blu-ray™ /

DVD Home

Cinema System

Please read this manual carefully before operating your set and retain it for future reference.

BH7240B (BH7240B, S74B1-F/S, S74T1-C, S73T1-W) BH7440P (BH7440P, S74T1-S/C, S74B1-S, S73T1-W) BH7540T (BH7540T, S74T1-S/C, S73T1-W)

P/NO : SAC35955101

1 GettingStarted

2 Getting Started

Safety Information

CAUTION

RISK OF ELECTRIC SHOCK

DO NOT OPEN

CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL.

This lightning flash with arrowhead symbol within an equilateral triangle

is intended to alert the user to the presence of uninsulated dangerous voltage within the product’s

enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.

The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing)

instructions in the literature accompanying the product.

WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING: Do not install this equipment in a confined space such as a book case or similar unit.

CAUTION: Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions.

Slots and openings in the cabinet are provided for ventilation and to ensure reliable operation of the product and to protect it from over heating. The openings shall be never be blocked by placing the product on a bed, sofa, rug or other similar surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless

proper ventilation is provided or the manufacturer’s instruction has been adhered to.

Use of controls, adjustments or the performance of procedures other than those specified herein may result in hazardous radiation exposure.

CAUTION concerning the Power Cord

Most appliances recommend they be placed upon a dedicated circuit;

That is, a single outlet circuit which powers only that appliance and has no additional outlets or branch circuits. Check the specification page of this owner’s manual to be certain. Do not overload wall outlets. Overloaded wall outlets, loose or damaged wall outlets, extension cords, frayed power cords, or damaged or cracked wire insulation are dangerous. Any of these conditions could result in electric shock or fire. Periodically examine the cord of your appliance, and if its appearance indicates damage or deterioration, unplug it, discontinue use of the appliance, and have the cord replaced with an exact replacement part by an authorized service center. Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and

the point where the cord exits the appliance. To disconnect power from the mains, pull out the mains cord plug. When installing the product, ensure that the plug is easily accessible.

		Getting Started 3
	This device is equipped with a portable battery or	Disposal of waste batteries/accumulators
	accumulator.	1. When this crossed-out wheeled
	Safety way to remove the battery or the
		bin symbol is attached to batteries/
	battery from the equipment: Remove the	accumulators of Your product it means
	old battery or battery pack, follow the steps	they are covered by European Directive
	in reverse order than the assembly. To prevent	2006/66/EC.
	contamination of the environment and bring on	2. This symbol may be combined with
	possible threat to human and animal health, the
		chemical symbols for mercury(Hg),
	old battery or the battery put it in the appropriate
		cadmium(Cd) or lead(Pb) if the battery
	container at designated collection points. Do
		Contains more that 0.0005% of
	not dispose of batteries or battery together with
		mercury,0.002% of cadmium or 0.004%
	other waste. It is recommended that you use
		of lead.
	local, free reimbursement systems batteries and
		3. All batteries/accumulators should be
	accumulators. The battery shall not be exposed to
		disposed separately from the municipal
	excessive heat such as sunshine, fire or the like.
		waste stream via designated collection
	CAUTION: The apparatus shall not be exposed to
		facilities appointed by the government
	water (dripping or splashing) and no objects filled
		or the local authorities.
	with liquids, such as vases, shall be placed on the
		4. The correct disposal of Your old
	apparatus.
		batteries/accumulators will help
	Disposal of your old appliance
		to prevent potential negative
	1. When this crossed-out wheeled bin	consequences for the environment,
	symbol is attached to a product it	animal and human health.
	means the product is covered by the	5. For more detailed information
	European Directive 2002/96/EC.
		about disposal of Your old batteries/
	2. All electrical and electronic products	accumulators, please contact Your
	should be disposed of separately	city office, waste disposal service or
	from the municipal waste stream	the shop where You purchased the
	via designated collection facilities	product.
	appointed by the government or the
	local authorities.

3.The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4.For more detailed information about disposal of your old appliance, please contact your city office, waste disposal service or the shop where you purchased the product.

1 GettingStarted

1 GettingStarted

4 Getting Started

	For Wireless product European Union Notice		Notes on copyrights
			yy Because AACS (Advanced Access Content
			System) is approved as content protection
	LG Electronics hereby declares that this/these		system for Blu-ray Disc format, similar to use of
	product(s) is/are in compliance with the essential		CSS (Content Scramble System) for DVD format,
	requirements and other relevant provisions of		certain restrictions are imposed on playback,
	Directive 1999/5/EC, 2004/108/EC, 2006/95/EC,		analog signal output, etc., of AACS protected
	2009/125/EC and 2011/65/EU.		content. The operation of this product and
	Please contact to the following address for		restrictions on this product may vary depending
			on your time of purchase as those restrictions
	obtaining a copy of the DoC (Declaration of
			may be adopted and/or changed by AACS after
	Conformity).
			the production of this product.
	Contact office for compliance of this product:
			yy Furthermore, BD-ROM Mark and BD+ are
	LG Electronics Inc.
			additionally used as content protection systems
	EU Representative, Krijgsman 1,
			for Blu-ray Disc format, which imposes certain
	1186 DM Amstelveen, The Netherlands
			restrictions including playback restrictions for
	yy Please note that this is NOT a Customer Service
			BD-ROM Mark and/or BD+ protected content. To
	contact point. For Customer Service Information,		obtain additional information on AACS, BD-ROM
	see Warranty Card or contact the dealer that you		Mark, BD+, or this product, please contact an
	purchased this product.		authorized Customer Service Center.
	Indoor use only.		yy Many BD-ROM/DVD discs are encoded with
	RF Radiation Exposure Statement		copy protection. Because of this, you should only
			connect your player directly to your TV, not to a
	This equipment should be installed and operated		VCR. Connecting to a VCR results in a distorted
	with minimum distance 20 cm between the		picture from copy-protected discs.
	radiator and your body.		yy This product incorporates copyright protection
			technology that is protected by U.S. patents
			and other intellectual property rights. Use of
			this copyright protection technology must be
			authorized by Rovi Corporation, and is intended
			for home and other limited viewing uses only
			unless otherwise authorized by Rovi Corporation.
			Reverse engineering or disassembly is prohibited.
			yy Under the U.S. Copyright laws and Copyright
			laws of other countries, unauthorized recording,
			use, display, distribution, or revision of television
			programs, videotapes, BD-ROM discs, DVDs, CDs
			and other materials may subject you to civil and/
			or criminal liability.

Important Notice for TV colour system

The colour system of this player differs according to currently playing discs.

For example, when the player plays the disc recorded in the NTSC colour system, the image is output as an NTSC signal.

Only the multi system colour TV can receive all signals output from the player.

yy If you have a PAL colour system TV, you will see just distorted images when using discs or video contents recorded in NTSC.

yy The multi system colour TV changes the colour system automatically according to input signals. In case that the colour system is not changed automatically, turn it off and then on to see normal images on screen.

yy Even if the disc recorded in NTSC colour system are well displayed on your TV, these may not be recorded correctly on your recorder.

>>Caution

yy Watching a 3D content for a long period time may cause dizziness or tiredness.

yy It is not recommended to watch a movie in 3D mode for infirm, child and pregnant woman.

yy If you are experiencing headache, tiredness or dizziness while viewing contents in 3D, it is strongly recommended to stop the playback and rest until you feel normal.

Getting Started

5

1 GettingStarted

6 Table of Contents

	Table of Contents				3	System Setting
				24		Initial Setup
				25		Settings
	1		Getting Started	25		–  Adjust the setup settings
				26		–  [NETWORK] menu
	2		Safety Information	27		–  [DISPLAY] menu
				28		–  [LANGUAGE] menu
	8		Introduction
				29		–  [AUDIO] menu
	8	–  Playable discs and symbols used in
				30		–  [LOCK] menu
			this manual
				31		–  [OTHERS] menu
	9 –  About the “7” symbol display
	9		–  Regional code
	9		–  System Select	4		Operating
	10		Remote Control
				33		Sound Effect
	11		Front Panel
				33		3D Sound Effect
	11		Rear Panel
				34		Home Menu Display
	2		Connecting	34		–  Using [HOME] menu
				34		–  Using the SmartShare
	12		Positioning the system	35		Playing the Linked Devices
				35		–  Playing a disc
	13		Speaker Connection
				35		–  Playing Blu-ray 3D disc
	13	–  Attaching the speakers to the player
				36		–  Playing a file on disc/USB device
	14 Connecting to your TV
				37		–  Playing a file on Android device
	15	–  What is SIMPLINK?
				38		–  Playing a file on a network server
	15	–  ARC (Audio Return Channel) function
				39		Using Home Network Server for PC
	15		–  Resolution setting
				39		–  About SmartShare PC Software
	16		Antenna connection
						(DLNA)
	17 Connections with external device
				39		–  Installing SmartShare PC Software
	17		–  AUX Connection
						(DLNA)
	17	–  OPTICAL IN connection
				39		–  Sharing files and folders
	18	–  HDMI IN 1/2 connection
				40		–  System requirements
	19 Connecting to your Home Network
				41		General Playback
	19	–  Wired network connection
				41		–  Basic operations for video and audio
	20		–  Wired network setup
						content
	21	–  Wireless network connection
				41		–  Basic operations for photo content
	21	–  Wireless network setup
				41		–  Using the disc menu
				42		–  Resume playback
				42		–  Last scene memory
				43		On-Screen Display
				43		–  To control video playback
				44		–  To control photo view
				45		Advanced Playback
				45		–  Repeat playback
				45		–  Repeating a specific portion
				45		–  Playing from selected time
				46		–  Selecting a subtitle language

					Table of Contents 7
	46	–  Hearing a different audio	5		Troubleshooting
	46	–  Watching from a different angle
			59		Troubleshooting
	46	–  Changing the TV Aspect Ratio
			59		–  General
	47	–  Changing subtitle Code Page
			60		–  Network
	47	–  Changing the Picture Mode
			61		–  Picture
	48	–  Viewing content information
			61		–  Sound
	48	–  Changing content list view
			61		–  Customer Support
	48	–  Selecting a subtitle file
			61		–  Open Source Software Notice
	49	–  Listening to music during slide show
	49	–  Converting 2D content to 3D
	50	Advanced Features	6		Appendix
	50	–  Wi-Fi Direct™
			62		Controlling a TV with the Supplied
	51	–  Enjoying Miracast™
	51	–  Enjoying BD-Live™			Remote Control
	52	–  Enjoying web browsing	62		–  Setting up the remote to control your
	52	–  LG AV Remote			TV
	52	–  Private Sound Mode	63		Network Software Update
	52	–  Using an USB keyboard or mouse	63		–  Network update notification
	53	Radio Operations	63		–  Software update
	53	–  Listening to the radio	65		Additional Information
	53	–  Presetting the Radio Stations	65		–  File requirement
	53	–  Deleting a saved station	66		–  AVCHD (Advanced Video Codec High
	53	–  Deleting all the saved stations			Definition)
	53	–  Improving poor FM reception	67		–  About DLNA
	53	–  See information about a radio station	67		–  Certain system requirements
	54	Using the Premium	67		–  Compatibility notes
	54	Using the LG Smart World	68		Audio Output Specifications
	55	–  Signing in	69		Area Code List
	55	–  Searching online content	70		Language Code List
	56	Using the My Apps Menu	71		Trademarks and Licenses
	57	Using Bluetooth technology	73		Specifications
	57	–  Listening to music stored on the	77		Maintenance
		Bluetooth devices	77		–  Handling the unit
			77		–  Notes on discs
			78		Important Information relating to Network
					Services

1

2

3

4

5

6

Some of the content in this manual may differ from your player depending on the software of the player or your service provider.

1 GettingStarted

8 Getting Started

Introduction

Playable discs and symbols used in this manual

	Media/Term	Logo		Symbol	Description
					yy Discs such as movies that can be purchased or
				e	rented.
					yy “Blu-ray 3D” discs and “Blu-ray 3D ONLY” discs.
	Blu-ray				yy BD-R/RE discs that are recorded in BDAV format.
				y	yy BD-R/RE discs that contain Movie, Music or
				u	Photo files.
				i	yy ISO 9660+JOLIET, UDF and UDF Bridge format
					yy Discs such as movies that can be purchased or
				r	rented.
	DVD-ROM				yy Movie mode and finalized only
					yy Supports the dual layer disc also
	DVD-R
	DVD-RW			o	Finalized AVCHD format
	DVD+R
	DVD+RW			y	yy DVD±R/RW discs that contain Movie, Music or
	(8 cm, 12cm)			u	Photo files.
					yy ISO 9660+JOLIET, UDF and UDF Bridge format
				i
	DVD-RW (VR)			r	VR mode and finalized only
	(8 cm, 12cm)
	Audio CD			t	Audio CD
	(8 cm, 12cm)
				y	yy CD-R/RW discs that contain Movie, Music or
	CD-R/RW			u	Photo files.
	(8 cm, 12cm)				yy ISO 9660+JOLIET, UDF and UDF Bridge format
				i
	Note	–		,	Indicates special notes and operating features.
	Caution	–		>	Indicates cautions for preventing possible damages
					from abuse.

Getting Started	9

,,Note

yy Depending on the conditions of the recording equipment or the CD-R/RW (or DVD±R/RW) disc itself, some CD-R/RW (or DVD±R/RW) discs cannot be played on the unit.

yy Depending on the recording software & the finalization, some recorded discs (CD-R/RW, DVD±R/RW, BD-R/RE) may not be playable.

yy BD-R/RE, DVD±R/RW and CD-R/RW discs recorded using a personal computer or a DVD or CD Recorder may not play if the disc is damaged or dirty, or if there is dirt or condensation on the player’s lens.

yy If you record a disc using a personal computer, even if it is recorded in a compatible format, there are cases in which it may not play because of the settings of the application software used to create the disc. (Check with the software publisher for more detailed information.)

yy This player requires discs and recordings to meet certain technical standards in order to achieve optimal playback quality.

yy Pre-recorded DVDs are automatically set to these standards. There are many different types of recordable disc formats (including CD-R containing MP3 or WMA files) and these require certain pre-existing conditions to ensure compatible playback.

yy Customers should note that permission is required in order to download MP3 / WMA files and music from the Internet. Our company has no right to grant such permission. Permission should always be sought from the copyright owner.

yy You have to set the disc format option to [Mastered] in order to make the discs compatible with the LG players when formatting rewritable discs. When setting

the option to Live System, you cannot use it on LG player. (Mastered/Live File System : Disc format system for windows Vista)

About the “7” symbol display

“7” may appear on your TV display during operation and indicates that the function explained in this owner’s manual is not available on that specific media.

Regional code

This unit has a regional code printed on the rear of the unit. This unit can play only BD-ROM or DVD discs labeled same as the rear of the unit or “ALL”.

System Select

Open the disc tray using the B(OPEN/CLOSE) button and then, press and hold M(PAUSE) for more than five seconds to change the color system (PAL /NTSC /AUTO).

1 GettingStarted

1 GettingStarted

10 Getting Started

Remote Control

Battery Installation

Remove the battery cover on the rear of the Remote Control, and insert two R03 (size AAA) batteries with 4and 5matched correctly.

	• • • • • • A• • •	•	TUNING +/-: Tunes in the desired
	1(POWER): Switches the player		radio station.
			ENTER (b): Acknowledges menu
	ON or OFF.
	B(OPEN/CLOSE): Opens and		selection.
			BACK (	): Exits the menu or
	closes the disc tray.
	FUNCTION: Changes input mode.		returns to the previous screen.
			TITLE/POPUP: Displays the DVD
	0-9 numerical buttons: Selects
			title menu or BD-ROM’s popup
	numbered options in a menu.
			menu, if available.
	CLEAR: Removes a number when
			DISC MENU: Accesses menu on a
	setting the password or network
			disc.
	connection.
	REPEAT (h): Repeats a desired		• • • •	• • D• • • •
	section or sequence.		Colored (R, G, Y, B) buttons:
	• • • • • • B• • •	•	- Use to navigate BD-ROM menus.
			They are also used as shortcut
	c/v(SCAN): Searches
			buttons for specific menus.
	backward or forward.
			- B button: Selects mono/ stereo
	C/V(SKIP): Goes to the
			in FM mode.
	next or previous chapter / track /		RDS: Radio Data System.
	file.
			PTY: Views the programme type
	Z(STOP): Stops playback.
			of the RDS.
	z(PLAY): Starts playback.
			PTY SEARCH:
	M(PAUSE): Pauses playback.
			Searches programme type.
	SPEAKER LEVEL: Sets the sound		SUBTITLE: Selects a subtitle
	level of desired speaker.		language.
	SOUND EFFECT: Selects a sound		AUDIO: Selects an audio language
	effect mode.		or audio channel.
	VOL +/-: Adjusts speaker volume.		SLEEP: Sets a certain period of
	OPTICAL/TV SOUND: Changes		time after which the unit will
	input mode to optical directly.		switch to off.
	MUTE: Mute the unit.		?: This button is not available.
	• • • • • • C• • •	•	TV Control Buttons: See page 62.

HOME (): Displays or exits the [Home].

3D SOUND: Selects a 3D sound effect mode.

INFO/MENU (m): Displays or exits On-Screen Display.

Direction buttons (W/S/ A/D): Selects an option in the menu.

PRESET +/-: Selects programme of Radio.

Getting Started 11

Front Panel

ADisc Tray

BOperation buttons R(OPEN/CLOSE) T(PLAY / PAUSE) I(STOP)

F (Function)

Changes the input source or function.

-/+ (Volume) 1/I (POWER)

CUSB Port

DDisplay Window

ERemote Sensor

1 GettingStarted

>>Caution

Precautions in using the touch buttons

yy Use the touch buttons with clean and dry hands.

- In a humid environment, wipe out any moisture on the touch buttons before using.

yy Do not press the touch buttons hard to make it work.

- If you apply too much strength, it can damage the sensor of the touch buttons.

yy Touch the button that you want to work in order to operate the function correctly.

yy Be careful not to have any conductive material such as metallic object on the touch buttons. It can cause malfunctions.

Rear Panel

A AC power cord

G USB Port (for connecting an USB keyboard or

B Speakers connectors

mouse)

H HDMI IN 1/2

C Cooling Fan

I HDMI OUT TO TV

D AUX (L/R) INPUT

J LAN port

E OPTICAL IN

F Antenna Connector

2

Connecting

12 Connecting

Positioning the system

The following illustration shows an example of positioning the system. Note that the illustrations in these instructions differ from the actual unit for explanation purposes.

For the best possible surround sound, all the speakers other than the subwoofer should be placed at the same distance from the listening position (A).

B

C

A G

F

A A

A

A E

>>Caution

yy Be careful to make sure children not to put their hands or any objects into the *speaker duct.

*Speaker duct: A hole for plentiful bass sound on speaker cabinet (enclosure).

yy Place the center speaker at a safe distance from the child’s reach.

Otherwise it may result in the speaker falling down and causing personal injury and/or property damage.

yy The speakers contain magnetic parts, so colour irregularity may occur on the CRT TV screen or PC monitor screen. Please use the speakers away from the TV screen or PC monitor screen.

yy Before using the subwoofer, remove the protective vinyl.

D A

AFront left speaker (L)/ BFront right speaker (R):

Place the front speakers to the sides of the monitor or screen and as flush with the screen surface as possible.

CCenter speaker:

Place the center speaker above or below the monitor or screen.

DSurround left speaker (L)/ ESurround right speaker (R):

Place these speakers behind your listening position, facing slightly inwards.

FSubwoofer:

The position of the subwoofer is not so critical, because low bass sounds are not highly directional. But it is better to place the subwoofer near the front speakers. Turn it slightly toward the center of the room to reduce the wall reflections.

GUnit

Speaker Connection

Attaching the speakers to the player

1.Connect speaker wires to the player.

Each speaker wire is color-coded. Use matching color wires for corresponding speakers.

Make sure the wire marked black goes in to the terminal marked “–” (minus) and the other wire goes in to the terminal marked “+” (plus).

Connect a woofer cord to the player. When connecting a woofer cord to the player, insert the connector until it clicks.

	Color	Speaker	Position
	Grey	Rear	Rear right
	Blue	Rear	Rear left
	Green	Center	Center
	Orange	Sub	Any front position
		woofer
	Red	Front	Front right
	White	Front	Front left

2.Connect the speaker wire to the terminal on the speaker.

Make sure the wire marked black goes in to the terminal marked “–” (minus) and the other wire goes in to the terminal marked “+” (plus).

Connecting 13

2

Connecting

2

Connecting

14 Connecting

Connecting to your TV

If you have a HDMI TV or monitor, you can connect it to this player using a HDMI cable (Type A, High Speed HDMI™ Cable). Connect the HDMI jack on the player to the HDMI jack on a HDMI compatible TV or monitor.

Rear of the unit

HDMI cable

TV

Set the TV’s source to HDMI (refer to TV’s owner’s manual).

,,Note

Please refer to the manuals of your TV, Stereo System or other devices as necessary to make the best connections.

Additional information for HDMI

yy When you connect a HDMI or DVI compatible device make sure of the following:

-- Try switching off the HDMI/DVI device and this player. Next, switch on the HDMI/DVI device and leave it for around 30 seconds, then switch on this player.

-- The connected device’s video input is set correctly for this unit.

-- The connected device is compatible with 720x576p, 1280x720p, 1920x1080i or 1920x1080p video input.

yy Not all HDCP-compatible HDMI or DVI devices will work with this player.

-- The picture will not be displayed properly with non-HDCP device.

,,Note

yy If a connected HDMI device does not accept the audio output of the player, the HDMI device’s audio sound may be distorted or may not output.

yy When you use HDMI connection, you can change the resolution for the HDMI output. (Refer to “Resolution setting” on page 15)

yy Select the type of video output from the HDMI OUT jack using [HDMI Color Setting] option on the [Settings] menu (page 28).

yy Changing the resolution when the connection has already been established may result in malfunctions. To solve the problem, turn off the player and then turn it on again.

yy When the HDMI connection with HDCP is not verified, TV screen is changed to black screen. In this case, check the HDMI

connection, or disconnect the HDMI cable.

yy If there are noises or lines on the screen, please check the HDMI cable (length is generally limited to 4.5 m (15 ft.)).

Connecting 15

What is SIMPLINK?

Some functions of this unit are controlled by the TV’s remote control when this unit and LG TV’s with SIMPLINK are connected through HDMI connection.

Controllable functions by LG TV’s remote control; Play, Pause, Scan, Skip, Stop, Power Off, etc.

Refer to the TV owner’s manual for the details of SIMPLINK function.

LG TV’s with SIMPLINK function has the logo as shown above.

,,Note

yy Depending on the disc type or playing status, some SIMPLINK operation may differ from your purpose or not work.

yy The SIMPLINK function is not supported for the device with SIMPLINK is connected to HDMI IN jack.

Resolution setting

The player provides several output resolutions for HDMI OUT jack. You can change the resolution using [Settings] menu.

1.Press HOME ().

2.Use A/Dto select the [Settings] and press ENTER (b). The [Settings] menu appears.

3.Use W/Sto select [DISPLAY] option then press Dto move to the second level.

4.Use W/Sto select the [Resolution] option then press ENTER (b) to move to the third level.

5.Use W/Sto select the desired resolution then press ENTER (b) to confirm your selection.

ARC (Audio Return Channel) function

The ARC function enables an HDMI capable TV to send the audio stream to HDMI OUT of this player.

To use this function:

-- Your TV must support the HDMI-CEC and ARC function and the HDMI-CEC and ARC must be set to On.

-- The setting method of HDMI-CEC and ARC may differ depending on the TV. For details about ARC function, refer to your TV manual.

-- You must use the HDMI cable (Type A, High Speed HDMI™ cable with Ethernet).

-- You must connect with the HDMI IN that supports the ARC function using the HDMI OUT on this player.

-- You can connect only one Home Theater to TV compatible with ARC.

,,Note

2

Connecting

To activate [SIMPLINK / ARC] function, set this option to [On]. (page 32)

2

Connecting

16 Connecting

,,Note

yy If your TV does not accept the resolution you have set on the player, you can set resolution to 576p as follows:

1.Press Bto open the disc tray.

2.Press Z(STOP) for more than 5 seconds.

yy If you select a resolution manually and then connect the HDMI jack to TV and your TV does not accept it, the resolution setting is set to [Auto].

yy If you select a resolution that your TV does not accept, the warning message will appear. After resolution change,

if you cannot see the screen, please wait 20 seconds and the resolution will automatically revert back to the previous resolution.

yy The 1080p video output frame rate may be automatically set to either 24 Hz or 50 Hz depending both on the capability and preference of the connected TV and

based on the native video frame rate of the content on the BD-ROM disc.

Antenna connection

Connect the supplied antenna for listening to the radio.

Rear of the unit

,,Note

After connecting the FM wire antenna, be sure to fully extend it.

Connecting 17

Connections with external device

AUX Connection

You can enjoy the sound from an external component through the speakers of this system.

Connect the analog audio output jacks of your component into the AUX L/R (INPUT) on this unit. And then select the [AUX] option by pressing FUNCTION.

You can also use the F (Function) button on the front panel to select the input mode.

Rear of the unit

White

Red

To the audio output jacks of your component (TV, VCR, etc.)

OPTICAL IN connection

You can enjoy the sound from your component with a digital optical connection through the speakers of this system.

Connect the optical output jack of your component into the OPTICAL IN jack on the unit. And then select the [OPTICAL] option by pressing FUNCTION. Or press OPTICAL/TV SOUND to select directly.

You can also use the F (Function) button on the front panel to select the input mode.

Rear of the unit

To the digital optical output jack of your component

2

Connecting

2

Connecting

18 Connecting

HDMI IN 1/2 connection

You can enjoy the pictures and sound from your component through this connection.

Connect the HDMI OUT jack of your component into the HDMI IN 1 or 2 jack on this unit. And then select the [HDMI IN 1/2] option by pressing FUNCTION.

You can also use the F (Function) button on the front panel to select the input mode.

Rear of the unit

To the HDMI OUT jack of your component

(set-top box, digital satellite receiver, video game machine, etc.)

,,Note

yy You cannot change the video resolution in the HDMI IN 1/2 mode. Change the video resolution of the connected component.

yy If the video output signal is abnormal when your personal computer is connected to HDMI IN 1/2 jack, change the resolution

of your personal computer to 576p, 720p, 1080i or 1080p.

yy The player sends audio from the HDMI inputs to both the HDMI output and to the unit’s speakers.

Connecting 19

Connecting to your Home Network

This player can be connected to a local area network (LAN) via the LAN port on the rear panel or the internal wireless module.

By connecting the unit to a broadband home network, you have access to services such as software updates, BD-Live interactivity and online content services.

Wired network connection

Using a wired network provides the best performance, because the attached devices connect directly to the network and are not subject to radio frequency interference.

Please refer to the documentation for your network device for further instructions.

Connect the player’s LAN port to the corresponding port on your Modem or Router using a commercially available LAN or Ethernet cable.

,,Note

yy When plugging or unplugging the LAN cable, hold the plug portion of the cable. When unplugging, do not pull on the LAN cable but unplug while pressing down on the lock.

yy Do not connect a modular phone cable to the LAN port.

yy Since there are various connection configurations, please follow the specifications of your telecommunication carrier or internet service provider.

yy If you want to access content from DLNA servers, this player must be connected to the same local area network with them via a router.

yy To set your PC as a DLNA server, install the SmartShare PC software on your PC. (page 39)

Broadband service

Router

DLNA certified servers

Rear of the unit

2

Connecting

2

Connecting

20 Connecting

Wired network setup

If there is a DHCP server on the local area network (LAN) via wired connection, this player will automatically be allocated an IP address. After making the physical connection, a small number of home networks may require the player’s network setting to be adjusted. Adjust the [NETWORK] setting as follow.

Preparation

Before setting the wired network, you need to connect the broadband internet to your home network.

1.Select [Connection Setting] option in the [Settings] menu then press ENTER (b).

2.Read the preparations for the network settings and then press ENTER (b) while [Start] is highlighted.

Network will automatically be connected to the unit.

Advanced Setting

If you want to set the network settings manually, use W/Sto select [Advanced Setting] on the

[Network Setting] menu and press ENTER (b).

1.Use W/Sto select [Wired] and press ENTER (b).

2.Use W/S/A/Dto select the IP mode between [Dynamic] and [Static].

Normally, select [Dynamic] to allocate an IP address automatically.

,,Note

If there is no DHCP server on the network and you want to set the IP address manually, select [Static] then set [IP Address], [Subnet Mask], [Gateway] and [DNS Server] using W/S/ A/Dand numerical buttons. If you make a mistake while entering a number, press CLEAR to clear the highlighted part.

3.Select [Next] and press ENTER (b) to apply network settings.

Network connection status is displayed on the screen.

4.Press ENTER (b) while [OK] is highlighted to finish the wired network settings.

Connecting 21

	Wireless network connection	Preparation
	Another connection option is to use an Access Point
		Before setting the wireless network, you need
	or a wireless router. The network configuration and
		to:
	connection method may vary depending on the
		-- connect the broadband internet to the
	equipment in use and the network environment.
		wireless home network.
		-- set the access point or wireless router.
		-- note the SSID and security code of the
		network.
	Wireless	1. Select [Connection Setting] option in the
		[Settings] menu then press ENTER (b).
	Communication	2. Read the preparations for the network settings
		and then press ENTER (b) while [Start] is
	DLNA certified servers	highlighted.
	Access Point or
	Wireless Router
		If wired network is not connected to the unit, all
	Broadband	available networks are displayed on the screen.
	service	3. Use W/Sto select a desired SSID of wireless
		network and press ENTER (b).
	Refer to the setup instructions supplied with
	your access point or wireless router for detailed
	connection steps and network settings.
	For best performance, a direct wired connection
	from this player to your home network’s router or
	cable/DSL modem is always the best option.
	If you do chose to use the wireless option, note that	If you have security on your access point, you
	performance can sometimes be affected by other
		need to input the security code as necessary.
	electronic devices in the home.
		,,Note
	Wireless network setup
		If you use other characters than the english
	For the wireless network connection, the player	alphabet or digits for the SSID name of your
		access point or wireless router, it may be
	needs to be set up for network communication.
		displayed differently.
	This adjustment can be done from the [Settings]
	menu. Adjust the [NETWORK] setting as follow.
	Setting up the access point or the wireless router
	is required before connecting the player to the
	network.

2

Connecting

2

Connecting

22 Connecting

,,Note

yy WEP security mode generally have 4 keys available on an access point setting. If your access point or wireless router use WEP security, enter the security code of the key “No.1” to connect on your home network.

yy An Access Point is a device that allows you to connect to your home network wirelessly.

4.Use W/S/A/Dto select the IP mode between [Dynamic] and [Static].

Normally, select [Dynamic] to allocate an IP address automatically.

,,Note

If there is no DHCP server on the network and you want to set the IP address manually, select [Static] then set [IP Address], [Subnet Mask], [Gateway] and [DNS Server] using W/S/ A/Dand numerical buttons. If you make a mistake while entering a number, press CLEAR to clear the highlighted part.

Advanced Setting

If you want to set the network settings manually, use W/Sto select [Advanced Setting] on the

[Network Setting] menu and press ENTER (b).

1.Use W/Sto select [Wireless] and press ENTER (b).

[AP List] - Scans all available access points or wireless routers within range and display them as a list.

[Network name (SSID)] – Your access point may not be broadcasting its network name (SSID). Check your access point settings through your computer and either set your access

point to broadcast SSID, or manually enter the network name in [Network name(SSID)].

[PBC] – If your access point or wireless router that supports the PBC (Push Button Configuration) method, select this option and press the Push Button on your access point

within 120 counts. You do not need to know the network name (SSID) and security code of your access point.

5.Select [Next] and press ENTER (b) to apply network settings.

Network connection status is displayed on the screen.

6.Select [OK] and press ENTER (b) to complete the network connection.

[PIN] – If your access point supports the PIN Code configuration method based on WPS(WiFi Protected Setup), select this option and note the code number on the screen. And then, enter the PIN number on a setting menu of your access point to connect. Refer to the documentation for your network device.

2.Follow the instructions of each connection method on the screen.

,,Note

To use PBC and PIN network connection, security mode of your access point must be set to OPEN or AES.

		Connecting 23
	Notes on network connection	yy A DSL modem is required to use DSL service and
	yy Many network connection problems during	a cable modem is required to use cable modem
		service. Depending on the access method of and
	set up can often be fixed by re-setting the
		subscriber agreement with your ISP, you may not
	router or modem. After connecting the player
		be able to use the internet connection feature
	to the home network, quickly power off and/
		contained in this player or you may be limited
	or disconnect the power cable of the home
		to the number of devices you can connect at
	network router or cable modem. Then power on
		the same time. (If your ISP limits subscription to
	and/or connect the power cable again.
		one device, this player may not be allowed to
	yy Depending on the internet service provider (ISP),
		connect when a PC is already connected.)
	the number of devices that can receive internet	yy The use of a “Router” may not be allowed or its
	service may be limited by the applicable terms
		usage may be limited depending on the policies
	of service. For details, contact your ISP.
		and restrictions of your ISP. For details, contact
	yy Our company is not responsible for any
		your ISP directly.
	malfunction of the player and/or the internet	yy The wireless network operate at 2.4 GHz
	connection feature due to communication
		radio frequencies that are also used by other
	errors/malfunctions associated with your
		household devices such as cordless telephone,
	broadband internet connection, or other
		Bluetooth® devices, microwave oven, and can be
	connected equipment.
		affected by interference from them.
	yy The features of BD-ROM discs made available
		yy Turn off all unused network equipment in
	through the Internet Connection feature are not
		your local home network. Some devices may
	created or provided by our company, and our
		generate network traffic.
	company is not responsible for their functionality
		yy For the purpose of the better transmission,
	or continued availability. Some disc related
	material available by the Internet Connection	placing the player from the access point as close
	may not be compatible with this player. If you	as possible.
	have questions about such content, please	yy In some instances, placing the access point or
	contact the producer of the disc.	wireless router at least 0.45 m (1.5 ft.) above the
	yy Some internet content may require a higher	floor may improve the reception.
	bandwidth connection.	yy Move closer to the access point if possible or re-
	yy Even if the player is properly connected and	orient the player so there is nothing between it
	configured, some internet content may not	and the access point.
	operate properly because of internet congestion,	yy The reception quality over wireless depends on
	the quality or bandwidth of your internet service,	many factors such as type of the access point,
	or problems at the provider of the content.	distance between the player and access point,
	yy Some internet connection operations may not	and the location of the player.
	be possible due to certain restrictions set by the	yy Set your access point or wireless router to
	Internet service provider (ISP) supplying your	Infrastructure mode. Ad-hoc mode is not
	broadband Internet connection.	supported.
	yy Any fees charged by an ISP including, without
	limitation, connection charges are your
	responsibility.
	yy A 10 Base-T or 100 Base-TX LAN port is required
	for wired connection to this player. If your
	internet service does not allow for such a
	connection, you will not be able to connect the
	player.
	yy You must use a Router to use xDSL service.

2

Connecting

3

Setting System

24	System Setting
Initial Setup			5. Use W/S/A/Dto select the IP mode
			between [Dynamic] and [Static].
			Normally, select [Dynamic] to allocate an IP
When you turn on the unit for the first time, the			address automatically.
initial setup wizard appears on the screen. Set the
display language and network settings on the initial
setup wizard.
1.	Press 1(POWER).
	The initial setup wizard appears on the screen.

2. Use W/S/A/Dto select a display language

and press ENTER (b).

6. Select [Next] and press ENTER (b) to apply network settings.

3.Read and prepare the preparations for the network settings and then press ENTER (b)

while [Start] is highlighted.	Network connection status is displayed on the
	screen.
	For details on network settings, refer to
	“Connecting to your Home Network” on page
	19.
	7. Select [Next] and press ENTER (b).
	8. Press ENTER (b) to verify the test tone signals of
	the speakers.
If wired network is connected, the network
connection setting will automatically be
finished.

4.All available networks are displayed on the screen. Use W/Sto select [Wired Network] or desired SSID of wireless network and press ENTER (b).

After verifying the test tone signals, press ENTER (b) while [Stop] is highlighted. Select [Next] and press ENTER (b).

If you have security on your access point, you need to input the security code as necessary.