Page 1
OWNER’S MANUAL
Blu-ray Disc™/DVD Player
Please read this manual carefully before operating
your set and retain it for future reference.
BD610
Rev. 00
Page 2
Getting Started2
Safety Information
1
Getting Started
CAUTION: TO REDUCE THE RISK OF ELECTRIC
SHOCK DO NOT REMOVE COVER (OR BACK) NO
USER-SERVICEABLE PARTS INSIDE REFER SERVICING
TO QUALIFIED SERVICE PERSONNEL.
enclosure that may be of sucient magnitude to
constitute a risk of electric shock to persons.
instructions in the literature accompanying the
product.
WARNING: TO PREVENT FIRE OR ELECTRIC SHOCK
HAZARD, DO NOT EXPOSE THIS PRODUCT TO RAIN
OR MOISTURE.
WARNING: Do not install this equipment in a
conned space such as a book case or similar unit.
CAUTION: Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
Slots and openings in the cabinet are provided for
ventilation and to ensure reliable operation of the
product and to protect it from over heating. The
openings shall be never be blocked by placing
the product on a bed, sofa, rug or other similar
surface. This product shall not be placed in a builtin installation such as a bookcase or rack unless
proper ventilation is provided or the manufacturer’s
instruction has been adhered to.
CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
This lightning ash with arrowhead
symbol within an equilateral triangle
is intended to alert the user to the
presence of uninsulated dangerous
voltage within the product’s
The exclamation point within an
equilateral triangle is intended
to alert the user to the presence
of important operating and
maintenance (servicing)
CAUTION: This product employs a Laser System.
To ensure proper use of this product, please read
this owner’s manual carefully and retain it for future
reference. Shall the unit require maintenance,
contact an authorized service center.
Use of controls, adjustments or the performance of
procedures other than those specied herein may
result in hazardous radiation exposure.
To prevent direct exposure to laser beam, do not try
to open the enclosure. Visible laser radiation when
open. DO NOT STARE INTO BEAM.
CAUTION concerning the Power Cord
Most appliances recommend they be placed upon
a dedicated circuit;
That is, a single outlet circuit which powers only
that appliance and has no additional outlets or
branch circuits. Check the specication page of this
owner’s manual to be certain. Do not overload wall
outlets. Overloaded wall outlets, loose or damaged
wall outlets, extension cords, frayed power cords, or
damaged or cracked wire insulation are dangerous.
Any of these conditions could result in electric
shock or re. Periodically examine the cord of your
appliance, and if its appearance indicates damage
or deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized service
center. Protect the power cord from physical or
mechanical abuse, such as being twisted, kinked,
pinched, closed in a door, or walked upon. Pay
particular attention to plugs, wall outlets, and
the point where the cord exits the appliance. To
disconnect power from the mains, pull out the
mains cord plug. When installing the product,
ensure that the plug is easily accessible.
Page 3
Getting Started 3
This device is equipped with a portable battery or
accumulator.
Safety way to remove the battery or the
battery from the equipment: Remove the
old battery or battery pack, follow the steps
in reverse order than the assembly. To prevent
contamination of the environment and bring on
possible threat to human and animal health, the
old battery or the battery put it in the appropriate
container at designated collection points. Do
not dispose of batteries or battery together with
other waste. It is recommended that you use
local, free reimbursement systems batteries and
accumulators. The battery shall not be exposed to
excessive heat such as sunshine, re or the like.
CAUTION: The apparatus shall not be exposed to
water (dripping or splashing) and no objects lled
with liquids, such as vases, shall be placed on the
apparatus.
FCC Compliance Statement
This device complies with part 15 of the FCC
rules. Operation is subject to the following two
conditions:
(1) This device may not cause harmful interference,
and
(2) This device must accept any interference
received, including interference that may cause
undesired operation.
NOTE: This equipment has been tested and found
to comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses, and can radiate radio
frequency energy and, if not installed and used
in accordance with the instructions, may cause
harmful interference to radio communications.
However, there is no guarantee that interference
will not occur in a particular installation.
If this equipment does cause harmful interference
to radio or television reception, which can be
determined by turning the equipment o and
on, the user is encouraged to try to correct the
interference by one or more of the following
measures:
yReorient or relocate the receiving antenna.
yIncrease the separation between the equipment
and receiver.
yConnect the equipment into an outlet on a
circuit dierent from that to which the receiver is
connected.
yConsult the dealer or an experienced radio/TV
technician for help.
CAUTION: Any changes or modications not
expressly approved by the party responsible for
compliance could void the user’s authority to
operate this equipment.
1
Getting Started
Page 4
Getting Started4
Notes on Copyrights
yBecause AACS (Advanced Access Content
System) is approved as content protection
1
Getting Started
system for Blu-ray Disc format, similar to use of
CSS (Content Scramble System) for DVD format,
certain restrictions are imposed on playback,
analogue signal output, etc., of AACS protected
contents. The operation of this product and
restrictions on this product may vary depending
on your time of purchase as those restrictions
may be adopted and/or changed by AACS after
the production of this product.
yFurthermore, BD-ROM Mark and BD+ are
additionally used as content protection systems
for Blu-ray Disc format, which imposes certain
restrictions including playback restrictions for
BD-ROM Mark and/or BD+ protected contents.
To obtain additional information on AACS, BDROM Mark, BD+, or this product, please contact
an authorized Customer Service Center.
yMany BD-ROM/DVD discs are encoded with
copy protection. Because of this, you should only
connect your player directly to your TV, not to a
VCR. Connecting to a VCR results in a distorted
picture from copy-protected discs.
yThis product incorporates copyright protection
technology that is protected by U.S. patents
and other intellectual property rights. Use of
this copyright protection technology must be
authorized by Rovi, and is intended for home and
other limited viewing uses only unless otherwise
authorized by Rovi. Reverse engineering or
disassembly is prohibited.
yUnder the U.S. Copyright laws and Copyright
laws of other countries, unauthorized recording,
use, display, distribution, or revision of television
programs, videotapes, BD-ROM discs, DVDs, CDs
and other materials may subject you to civil and/
or criminal liability.
IMPORTANT SAFETY
INSTRUCTIONS
1. Read these instructions.
2. Keep these instructions.
3. Heed all warnings.
4. Follow all instructions.
5. Do not use this apparatus near water.
6. Clean only with dry cloth.
7. Do not block any ventilation openings.
Install in accordance with the manufacturer’s
instructions.
8. Do not install near any heat sources such
as radiators, heat registers, stoves, or other
apparatus (including ampliers) that produce
heat.
9. Do not defeat the safety purpose of the
polarized or grounding-type plug. A polarized
plug has two blades with one wider than the
other. A grounding type plug has two blades
and a third grounding prong. The wide blade or
the third prong are provided for your safety. If
the provided plug does not t into your outlet,
consult an electrician for replacement of the
obsolete outlet.
10. Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.
11. Only use attachments/accessories specied by
the manufacturer.
12. Use only with the cart, stand,
tripod, bracket, or table
specied by the manufacturer,
or sold with the apparatus.
When a cart is used, use
caution when moving the cart/
apparatus combination to avoid injury from tipover.
13. Unplug this apparatus during lightning storms
or when unused for long periods of time.
14. Refer all servicing to qualied service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as powersupply cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has been exposed to rain or
moisture, does not operate normally, or has
been dropped.
Page 5
Table of Contents 5
Table of Contents
1 Getting Started
2 Safety Information
6 Introduction
11 Remote control
12 Front panel
12 Rear panel
2 Connecting
13 Connecting to Your TV
13 – HDMI Connection
14 – Video/Audio (Left/Right) Connection
15 – Resolution Setting
15 Connecting to an Amplifier
16 USB device connection
16 – Playback content in the USB device
3 System Setting
18 Settings
18 – Adjust the Setup Settings
18 – [DISPLAY] Menu
19 – [LANGUAGE] Menu
20 – [AUDIO] Menu
21 – [LOCK] Menu
22 – [OTHERS] Menu
4 Operating
23 General Playback
23 – Using [HOME] menu
23 – Playing a Disc
23 – Playing a file on a disc/USB device
24 – Basic operations for video and audio
content
24 – Basic operations for photo content
24 – Using the disc menu
25 – Resume playback
25 Advanced Playback
25 – Repeat Playback
26 – Repeating a specific portion
26 – Enlarge the playback image
26 – Marker Search
27 – Using the search menu
27 – Changing content list view
28 – Viewing content information
28 – Selecting a subtitle file
28 – Last Scene Memory
29 – Options while viewing a photo
29 – Listening to music while slide show
30 On-Screen display
30 – Displaying content information on-
screen
30 – Playing from selected time
31 – Hearing a different audio
31 – Selecting a subtitle language
31 – Watching from a different angle
31 – Changing the TV Aspect Ratio
32 – Changing the Picture Mode
32 – Changing subtitle code page
5 Troubleshooting
33 Troubleshooting
33 – General
34 – Picture
34 – Sound
34 – Customer Support
34 – Open source software notice
6 Appendix
35 Area Code List
36 Language Code List
37 Audio Output Specifications
38 Trademarks and Licenses
39 Specifications
40 Maintenance
7 Warranty
41 Limited Warranty
1
2
3
4
5
6
7
Page 6
Getting Started6
Introduction
1
Playable Discs and symbols used in this manual
Getting Started
Media/Term Logo Symbol Description
yDiscs such as movies that can be purchased or
rented.
yBD-R/RE discs that are recorded in BDAV format.
yBD-R/RE discs that contain Video, Audio or
Photo les.
yISO 9660+JOLIET, UDF and UDF Bridge format
yDiscs such as movies that can be purchased or
rented.
yVideo mode and nalized only
ySupports the dual layer disc also
Finalized AVCHD format
yDVD±R/RW discs that contain Video, Audio or
Photo les.
yISO 9660+JOLIET, UDF and UDF Bridge format
Blu-ray
DVD-ROM
DVD-R
DVD-RW
DVD+R
DVD+RW
(8 cm / 12
cm disc)
e
y
u
i
r
o
y
u
i
DVD-RW
(VR)
(8 cm / 12
cm disc)
Audio CD
(8 cm / 12
cm disc)
CD-R/RW
(8 cm / 12
cm disc)
Note –
Caution –
r
t
y
u
i
,
>
VR mode and nalized only
Audio CD
yCD-R/RW discs that contain Video, Audio or
Photo les.
yISO 9660+JOLIET, UDF and UDF Bridge format
Indicates special notes and operating features.
Indicates cautions for preventing possible
damages from abuse.
Page 7
Note
,
yDepending on the conditions of the
recording equipment or the CD-R/RW (or
DVD±R/RW) disc itself, some CD-R/RW (or
DVD±R/RW) discs cannot be played on the
unit.
yDepending on the recording software & the
nalization, some recorded discs (CD-R/RW,
DVD±R/RW, BD-R/RE) may not be playable.
yBD-R/RE, DVD±R/RW and CD-R/RW discs
recorded using a personal computer or a
DVD or CD Recorder may not play if the
disc is damaged or dirty, or if there is dirt or
condensation on the player’s lens.
yIf you record a disc using a personal
computer, even if it is recorded in a
compatible format, there are cases in which
it may not play because of the settings of
the application software used to create the
disc. (Check with the software publisher for
more detailed information.)
yThis player requires discs and recordings to
meet certain technical standards in order to
achieve optimal playback quality.
yPre-recorded DVDs are automatically set to
these standards. There are many dierent
types of recordable disc formats (including
CD-R containing MP3 or WMA les) and
these require certain pre-existing conditions
to ensure compatible playback.
yCustomers should note that permission
is required in order to download MP3 /
WMA les and music from the Internet.
Our company has no right to grant such
permission. Permission should always be
sought from the copyright owner.
yYou have to set the disc format option
to [Mastered] in order to make the discs
compatible with the LG players when
formatting rewritable discs. When setting
the option to Live System, you cannot use
it on LG player. (Mastered/Live File System :
Disc format system for windows Vista)
Getting Started 7
About the “7” Symbol Display
“7” may appear on your TV display during
operation and indicates that the function explained
in this owner’s manual is not available on that
specic media.
Supplied Accessories
Audio / Video Cable (1) Remote control (1)
Battery (1)
1
Getting Started
Page 8
Getting Started8
File compatibility
Video files
1
Getting Started
File
Location
Disc, USB
Audio files
File
Extension
“.avi”, “.mpg”,
“.mpeg”, “.mkv ”,
“.mp4”, “.asf”
Codec Format Audio Format Subtitle
XVID, MPEG1 SS,
H.264/MPEG-4 AVC,
MPEG2 PS, MPEG2 TS
Dolby Digital,
DTS, MP3,
WMA, AAC,
AC3
SubRip (.srt / .txt), SAMI (.smi),
SubStation Alpha (.ssa/.txt),
MicroDVD (.sub/.txt), VobSub
(.sub), SubViewer 1.0 (.sub),
SubViewer 2.0 (.sub/.txt), TMPlayer
(.txt), DVD Subtitle System (.txt)
File
Location
Disc, USB
Photo files
File
Location
Disc, USB
File
Extension
“mp3”, “.wma”,
“.wav”, “.m4a”
(DRM free)
File
Extension
“.jpg”, “.jpeg”,
“.png”, “.gif ”
Sampling Frequency Bitrate Note
within 32 - 48 kHz
(WMA),
within 11 - 48 kHz (MP3)
Recommanded Size Note
Less than 4,000 x 3,000 x 24 bit/pixel
Less than 3,000 x 3,000 x 32 bit/pixel
within 32 - 192
kbps (WMA),
within 8 - 320 kbps
(MP3),
Progressive and lossless
compression photo image les
are not supported.
Some wav les are
not supported on this
player.
Page 9
Note
,
yThe le name is limited to 180 characters.
yA “avi” le which is encoded “WMV 9 codec”
is not supported.
yDepending on the size and number of the
les, it may take several minutes to read the
contents on the media.
yThis unit cannot support the ID3 Tag
embedded MP3 le.
yThe total playback time of music le
indicated on the screen may not correct for
VBR les.
yHD video les contained on the CD or USB
1.0/1.1 may not play properly. Blu-ray Disc,
DVD or USB 2.0 are recommended to play
back HD video les.
yThis player supports H.264/MPEG-4 AVC
prole Main, High at Level 4.1. For a le
with higher level, the warning message will
appear on the screen.
yThis player does not support les that are
recorded with GMC
*1 GMC – Global Motion Compensation
*2 Qpel – Quarter pixel
yThis player supports UTF-8 les even it
contains Unicode subtitle contents. This
player can not support the pure Unicode
subtitle les.
yDepending on the types of le or ways of
recording, it may not play back.
yA disc which was recorded by multi-session
on normal PC is not supported on this
player.
yTo be play back a movie le, movie le
name and Subtitle le name must be the
same.
yIf video codec is MPEG2 TS or MPEG2 PS,
subtitle does not play back.
1
or Qpel
*
2
.
*
Getting Started 9
AVCHD (Advanced Video
Codec High Definition)
yThis player can playback AVCHD format discs.
These discs are normally recorded and used in
camcorders.
yThe AVCHD format is a high denition digital
video camera format.
yThe MPEG-4 AVC/H.264 format is capable of
compressing images at higher eciency than
that of the conventional image compressing
format.
yThis player can playback AVCHD discs using
“x.v.Color” format.
ySome AVCHD format discs may not play
depending on the recording condition.
yAVCHD format discs need to be nalized.
y“x.v.Color” oers a wider color range than normal
DVD camcorder discs.
1
Getting Started
Page 10
Getting Started10
Certain System Requirements
For high denition video playback:
yHigh denition display that has HDMI input jack.
1
yBD-ROM disc with high denition content.
Getting Started
yHDMI or HDCP capable DVI input on your display
device is required for some content (as specied
by disc authors).
For Dolby® Digital Plus, Dolby TrueHD and DTS-HD
multi-channel audio playback:
yAn amplier/receiver with a built-in (Dolby
Digital, Dolby Digital Plus, Dolby TrueHD, DTS or
DTS-HD) decoder.
yMain, center, surround speakers and subwoofer
as necessary for chosen format.
About Digital Multi-channel
sound
A digital multi-channel connection provides the
best sound quality. For this, you need a multichannel Audio/Video Receiver that supports one
or more of the audio formats supported by your
player. Check the logos on the front of the Audio/
Video receiver and the manual. (PCM Stereo, PCM
Multi-Ch, Dolby Digital, Dolby Digital Plus, Dolby
TrueHD, DTS and/or DTS-HD)
Compatibility Notes
yBecause BD-ROM is a new format, certain disc,
digital connection and other compatibility issues
are possible. If you experience compatibility
problems, please contact an authorized
Customer Service Center.
yThis unit allows you to enjoy functions such
as picture-in-picture, secondary audio and
Virtual packages, etc., with BD-ROM supporting
BONUSVIEW (BD-ROM version 2 Prole 1 version
1.1). Secondary video and audio can be played
from a disc compatible with the picture-inpicture function. For the playback method, refer
to the instructions in the disc.
yViewing high-denition content and up-
converting standard DVD content may require a
HDMI-capable input or HDCP-capable DVI input
on your display device.
ySome BD-ROM and DVD discs may restrict the
use of some operation commands or features.
yDolby TrueHD, Dolby Digital Plus and DTS-HD are
supported with maximum 7.1 channels if you
use HDMI connection for the audio output of the
unit.
Regional Code
This unit has a regional code printed on the rear of
the unit. This unit can play only BD-ROM or DVD
discs labeled same as the rear of the unit or “ALL”.
Page 11
Remote control
Getting Started 11
• • • • • • a • • • • • •
(POWER): Switches the player
1
ON or OFF.
(OPEN/CLOSE): Opens and
B
closes the disc tray.
TV Control Buttons: Control the
sound volume, channel, sources,
and power On/O on TV.
0-9 numerical buttons: Selects
numbered options in a menu.
CLEAR: Removes a mark on the
search menu or a number when
setting the password.
• • • • • • b • • • • •
c/v
backward or forward.
C/V
next or previous chapter / track /
le.
M
d
Z
(SCAN): Searches
(SKIP): Goes to the
(PAUSE): Pauses playback.
(PLAY): Starts playback.
(STOP): Stops playback.
• • • • • • c • • • • •
HOME (n): Displays or exits the
[Home Menu].
INFO/DISPLAY (m): Displays or
exits On-Screen Display.
Direction buttons: Selects an
option in the menu.
ENTER (b): Acknowledges menu
selection.
BACK (x): Exits the menu or
resumes playback. The resume
play function may not work
depending on the BD-ROM disc.
DISC MENU: Accesses menu on a
disc.
• • • • • • d • • • • •
ZOOM: Displays or exits the
[Zoom] menu.
MARKER: Marks any point during
playback.
SEARCH: Displays or exits the
search menu.
TITLE/POP-UP: Displays the DVD
title menu or BD-ROM’s pop-up
menu, if available.
Colored (R, G, Y, B) buttons: Use
to navigate BD-ROM menus. They
are also used for [MOVIE], [PHOTO]
or [MUSIC].
REPEAT (h): Repeats a desired
section or sequence.
AUDIO ([): Selects an audio
language.
SUBTITLE (]): Selects a subtitle
language.
TV MUTE: Turn the TV’s volume
on or o.
Battery Installation
Remove the battery cover on the
rear of the Remote Control, and
insert R03 (size AAA) battery with
and 5 matched correctly.
4
Code number to control
TVs
1. While holding down 1
(TV POWER), and press the
manufacturer code for your
TV with the numerical buttons
(see the table below).
Maker Code Number
LG 1(Default), 2
Zenith 1, 3, 4
GoldStar 1, 2
Samsung 6, 7
Sony 8, 9
Hitachi 4
2. Release the 1 (TV POWER)
button to complete setting.
1
Getting Started
Page 12
Getting Started12
Front panel
1
Getting Started
Disc Tray
a
Display Window
b
Remote Sensor
c
(OPEN/CLOSE)
d B
Rear panel
AC power cord
a
VIDEO OUT
b
(PLAY / PAUSE)
e N
(STOP)
f Z
(POWER)
g 1
USB Port
h
AUDIO OUT (Left/Right)
c
HDMI OUT
d
Page 13
Connecting 13
Connecting to Your TV
Make one of the following connections, depending
on the capabilities of your existing equipment.
yHDMI connection (page 13)
yVideo/Audio connection (page 14)
Note
,
yDepending on your TV and other
equipment you wish to connect, there are
various ways you could connect the player.
Use only one of the connections described
in this manual.
yPlease refer to the manuals of your TV,
Stereo System or other devices as necessary
to make the best connections.
yDo not connect the player’s AUDIO OUT
jack to the phono in jack (record player) of
your audio system.
yDo not connect your player via your VCR.
The image could be distorted by the copy
protection system.
HDMI Connection
If you have a HDMI TV or monitor, you can connect
it to this player using a HDMI cable (Type A, High
Speed HDMI
the player to the HDMI jack on a HDMI compatible
TV or monitor.
Set the TV’s source to HDMI (refer to TV’s Owner’s
manual).
TM
Cable). Connect the HDMI jack on
Rear of the unit
HDMI
cable
TV
2
Connecting
Additional Information for HDMI
yWhen you connect a HDMI or DVI compatible
device make sure of the following:
-Try switching o the HDMI/DVI device and
this player. Next, switch on the HDMI/DVI
device and leave it for around 30 seconds,
then switch on this player.
-The connected device’s video input is set
correctly for this unit.
-The connected device is compatible with
720x480p, 1280x720p, 1920x1080i or
1920x1080p video input.
yNot all HDCP-compatible HDMI or DVI devices
will work with this player.
-The picture will not be displayed properly
with non-HDCP device.
-This player does not playback and TV screen
is changed to black screen.
Page 14
2
Connecting
14
Connecting
Note
,
yIf a connected HDMI device does not accept
the audio output of the player, the HDMI
device’s audio sound may be distorted or
may not output.
yWhen you use HDMI connection, you can
change the resolution for the HDMI output.
(Refer to “Resolution Setting” on page 15)
ySelect the type of video output from the
HDMI OUT jack using [HDMI Color Setting]
option on the [Setup] menu (see page 19).
yChanging the resolution when the
connection has already been established
may result in malfunctions. To solve the
problem, turn o the player and then turn it
on again.
yWhen the HDMI connection with HDCP
is not veried, TV screen is changed to
black screen. In this case, check the HDMI
connection, or disconnect the HDMI cable.
yIf there are noises or lines on the screen,
please check the HDMI cable (length is
generally limited to 4.5 m(15 ft.)).
Video/Audio (Left/Right) Connection
Connect the VIDEO OUT jack on the player to the
video in jack on the TV using a video cable. Connect
the left and right AUDIO OUT jacks of the player to
the audio left and right IN jacks on the TV using the
audio cables.
Rear of the unit
Audio / Video cable
What is SIMPLINK?
Some functions of this unit are controlled by the
TV’s remote control when this unit and LG TV’s with
SIMPLINK are connected through HDMI connection.
Controllable functions by LG TV’s remote control;
Play, Pause, Scan, Skip, Stop, Power O, etc.
Refer to the TV owner’s manual for the details of
SIMPLINK function.
LG TV’s with SIMPLINK function has the logo as
shown above.
Note
,
Depending on the disc type or playing status,
some SIMPLINK operation may dier from your
purpose or not work.
TV
Page 15
Resolution Setting
The player provides several output resolutions for
HDMI OUT. You can change the resolution using
[Setup] menu.
1. Press HOME (n).
2. Use
ENTER (b). The [Setup] menu appears.
3. Use
d
4. Use
press ENTER (b) to move to the third level.
5. Use
press ENTER (b) to conrm your selection.
to select the [Setup] and press
a/d
to select [DISPLAY] option then press
w/s
to move to the second level.
to select the [Resolution] option then
w/s
to select the desired resolution then
w/s
Connecting 15
Note
,
yIf your TV does not accept the resolution
you have set on the player, you can set
resolution to 480p as follows:
1. Press B to open the disc tray.
2 Press Z (STOP) for more than 5 seconds.
yWhen you set the HDMI Resolution, over
720p is not outputted to Composite Video.
yIf you select a resolution manually and then
connect the HDMI jack to TV and your TV
does not accept it, the resolution setting is
set to [Auto].
yIf you select a resolution that your TV
does not accept, the warning message
will appear. After resolution change,
if you cannot see the screen, please
wait 20 seconds and the resolution will
automatically revert back to the previous
resolution.
yThe 1080p video output frame rate may
be automatically set to either 24 Hz or
60 Hz depending both on the capability
and preference of the connected TV and
based on the native video frame rate of the
content on the BD-ROM disc.
yThe resolution of the VIDEO OUT jack is
always outputted at 480i resolution.
2
Connecting
Page 16
Connecting16
Connecting to an
Amplifier
Make one of the following connections, depending
on the capabilities of your existing equipment.
yHDMI Audio connection
y2CH Analog Audio connection
Since many factors aect the type of audio output,
2
Connecting
see “Audio Output Specications” for details (page
37).
Connecting to an Amplifier via
HDMI Output
Connect the player’s HDMI OUT jack to the
corresponding in jack on your amplier using a
HDMI cable.
Connect the amplier’s HDMI output jack to HDMI
input jack on your TV using a HDMI cable if your
amplier has HDMI output jack.
You will need to activate the player’s digital output.
(See “[AUDIO] Menu” on page 20.)
Connecting to an Amplifier via
2 Channel Audio Output
Connect the Left and Right 2CH AUDIO OUT jacks
on the player to the audio left and right in jacks
on your amplier, receiver, or stereo system using
audio cables.
Rear of the unit
Rear of the unit
Audio cable
TV
HDMI cable
Receiver/Amplier
HDMI
cable
Receiver/Amplier
Page 17
USB device connection
This player can play Video, Audio and photo les
contained in the USB device.
Playback content in the USB device
1. Insert a USB device to the USB port until it ts
into place.
When you connect the USB device on the HOME
menu, the player plays a music le contained in the
USB storage device automatically. If the USB storage
device is containing various types of les, a menu
for the le type selection will appear.
File loading may takes few minutes depending on
the number of content stored in the USB storage
device. Press ENTER (b) while [Cancel] is selected
to stop loading.
2. Press HOME (n).
3. Select [Movie], [Photo] or [Music] using
and press ENTER (b).
4. Select the [USB] option using
ENTER (b).
w/s
, and press
a/d
,
Connecting 17
Note
,
yThis player supports USB ash drive/external
HDD formatted in FAT16, FAT32 and NTFS
when accessing les (music, photo, movie).
However, for Blu-ray contents, only FAT16
and FAT32 formats are supported. Use the
USB ash drive/external HDD formatted in
either FAT16 or FAT32 when enjoying Blu-ray
contents.
yThe USB device can be used for the local
storage for enjoying Blu-ray contents.
yThis unit can support up to 4 partitions of
the USB device.
yDo not extract the USB device during
operation (play, etc.).
yA USB device which requires additional
program installation when you have
connected it to a computer, is not
supported.
yUSB device: USB device that supports
USB1.1 and USB2.0.
yVideo, Audio and photo les can be played.
For details of operations on each le, refer to
relevant pages.
yRegular back up is recommended to
prevent data loss.
yIf you use a USB extension cable, USB HUB
or USB Multi-reader, the USB device may not
be recognized.
ySome USB device may not work with this
unit.
yDigital camera and mobile phone are not
supported.
yUSB Port of the unit cannot be connected
to PC. The unit cannot be used as a storage
device.
2
Connecting
5. Select a le using
PLAY (d) or ENTER (b) to play the le.
6. Withdraw the USB device carefully.
w/s/a/d
, and press
Page 18
System Setting18
Settings
Adjust the Setup Settings
You can change the settings of the player in the
[Setup] menu.
1. Press HOME (n).
3
System Setting
2. Use
ENTER (b). The [Setup] menu appears.
3. Use
press d to move to the second level.
to select the [Setup] and press
a/d
to select the rst setup option, and
w/s
[DISPLAY] Menu
TV Aspect Ratio
Select a TV aspect ratio option according to your TV
type.
[4:3 Letter Box]
Select when a standard 4:3 TV is connected.
Displays theatrical images with masking bars
above and below the picture.
[4:3 Pan Scan]
Select when a standard 4:3 TV is connected.
Displays pictures cropped to ll your TV screen.
Both sides of the picture are cut o.
[16:9 Original]
Select when a 16:9 wide TV is connected. The
4:3 picture is displayed with an original 4:3
aspect ratio, with black bars appearing at the
left and right sides.
[16:9 Full]
Select when a 16:9 wide TV is connected. The
4:3 picture is adjusted horizontally (in a linear
proportion) to ll the entire screen.
Note
,
You cannot select [4:3 Letter Box] and
[4:3 Pan Scan] option when the resolution is
set to higher than 720p.
4. Use
press ENTER (b) to move to the third level.
5. Use
ENTER (b) to conrm your selection.
to select a second setup option, and
w/s
to select a desired setting, and press
w/s
Page 19
System Setting 19
Resolution
Sets the output resolution of HDMI video signal.
Refer to page 15 for details about the resolution
setting.
[Auto]
If the HDMI OUT jack is connected to
TVs providing display information (EDID),
automatically selects the resolution best suited
to the connected TV.
[1080p]
Outputs 1080 lines of progressive video.
[1080i]
Outputs 1080 lines of interlaced video.
[720p]
Outputs 720 lines of progressive video.
[480p]
Outputs 480 lines of progressive video.
[480i]
Outputs 480 lines of interlaced video.
1080p Display Mode
When the resolution is set to 1080p, select
[24 Hz] for smooth presentation of lm material
(1080p/24 Hz) with a HDMI-equipped display
compatible with 1080p/24 Hz input.
Note
,
yWhen you select [24 Hz], you may
experience some picture disturbance when
the video switches video and lm material.
In this case, select [60 Hz].
yEven when [1080p Display Mode] is set to
[24 Hz], if your TV is not compatible with
1080p/24 Hz, the actual frame frequency of
the video output will be 60 Hz to match the
video source format.
HDMI Color Setting
Select the type of output from the HDMI OUT jack.
For this setting, please refer to the manuals of your
display device.
[YCbCr]
Select when connecting to a HDMI display
device.
[RGB]
Select when connecting to a DVI display
device.
Wallpaper
Changes the background of the initial screen.
[LANGUAGE] Menu
Display Menu
Select a language for the [Setup] menu and onscreen display.
Disc Menu/Disc Audio/
Disc Subtitle
Select the language you prefer for the audio track
(disc audio), subtitles, and the disc menu.
[Original]
Refers to the original language in which the
disc was recorded.
[Other]
Press ENTER (b) to select another language.
Use number buttons then press ENTER (b)
to enter the corresponding 4-digit number
according to the language code list on page
36.
[O] (Disc Subtitle only)
Turn o Subtitle.
3
System Setting
Note
,
Depending on the disc, your language setting
may not work.
Page 20
System Setting20
[AUDIO] Menu
Each disc has a variety of audio output options. Set
the player’s Audio options according to the type of
audio system you use.
Note
,
Since many factors aect the type of audio
output, see “Audio Output Specications” on
page 37 for details.
HDMI
[PCM Stereo]
Select if you connect this unit’s HDMI OUT jack
3
System Setting
to a device with two-channel digital stereo
decoder.
[PCM Multi-Ch]
Select if you connect this unit’s HDMI OUT jack
to a device with multi-channel digital decoder.
[DTS Re-Encode]
Select if you connect this unit’s HDMI OUT jack
to a device with DTS decoder.
[Primary Pass-Thru]
Select if you connect this unit’s HDMI OUT jack
to a device with LPCM, Dolby Digital, Dolby
Digital Plus, Dolby TrueHD, DTS and DTS-HD
decoder.
Sampling Freq.
(Digital Audio Output)
[48 kHz]
Select this if your A/V Receiver or Amplier is
not capable of handling 192 kHz and 96 kHz
signal. When this choice is made, this unit
automatically converts any 192 kHz and 96 kHz
signals to 48 kHz so your system can decode
them.
[96 kHz]
Select this if your A/V Receiver or Amplier is
not capable of handling 192 kHz signals. When
this choice is made, this unit
automatically converts any 192 kHz signals to
96 kHz so your system can decode them.
[192 kHz]
Select this if your A/V Receiver or Amplier is
capable of handling 192 kHz signals.
Check the documentation for your A/V Receiver or
Amplier to verify its capabilities.
Note
,
yWhen [HDMI] option is set to [PCM Multi-
Ch], the audio may output as PCM Stereo
if the PCM Multi-Ch information is not
detected from HDMI device with EDID.
yIf the [HDMI] option is set to [DTS Re-
Encode], the DTS Re-Encode audio is
outputted for BD-ROM discs with secondary
audio and the original audio is outputted
for the other discs (like [Primary Pass-Thru]).
Page 21
System Setting
21
DRC (Dynamic Range Control)
This function allows you to listen to a movie at a
lower volume without losing clarity of sound.
[Auto]
The dynamic range of the Dolby TrueHD audio
output is specied by itself.
And the dynamic range of the Dolby Digital
and Dolby Digital Plus are operated as same as
the [On] mode.
[On]
Compress the dynamic range of the Dolby
Digital, Dolby Digital Plus or Dolby TrueHD
audio output.
[O]
Turns o this function.
Note
,
The DRC setting can be changed only when a
disc is not inserted or the unit is in complete
stop mode.
[LOCK] Menu
The [LOCK] settings aect only Blu-ray Disc and
DVD playback.
To access the any features in [LOCK] settings, you
must enter the 4-digit security code you have
created.
If you have not entered a password yet, you are
prompted to do so. Enter a 4-digit password twice,
and press ENTER (b) to create a new password.
Password
You can create or change the password.
[None]
Enter a 4-digit password twice, and press
ENTER (b) to create a new password.
[Change]
Enter the current password and press
ENTER (b). Enter a 4-digit password twice, and
press ENTER (b) to create a new password.
If you forget your password
If you forget your password, you can clear it using
the following steps:
1. Remove any disc that might be in the player.
2. Select [Password] option in the [Setup] menu.
3. Use Number buttons to enter “210499”. The
password is cleared.
Note
,
If you make a mistake before pressing ENTER (b),
press CLEAR. Then input the correct password.
3
System Setting
Page 22
System Setting22
DVD Rating
Blocks playback of rated DVD based on their
content. (Not all discs are rated.)
[Rating 1-8]
Rating one (1) has the most restrictions and
rating eight (8) is the least restrictive.
[Unlock]
If you select [Unlock], parental control is not
active and the disc plays in full.
Blu-ray Disc Rating
Set an age limit of BD-ROM play. Use number
buttons to input an age limit for BD-ROM viewing.
3
System Setting
[255]
All BD-ROM can be played.
[0-254]
Prohibits play of BD-ROM with corresponding
ratings recorded on them.
Note
,
yThe [Blu-ray Disc Rating] will be applied
only for the Blu-ray Disc that containing the
Advanced Rating Control.
yFor the region using MPAA rating level, refer
to the table below as an example.
[OTHERS] Menu
Auto Power Off
The screen saver appears when you leave the player
in Stop mode for about ve minutes. If you set this
option to [On], the unit automatically turns itself o
after the Screen Saver is displayed for 20 minutes.
Set this option to [O ] to leave the screen saver
until the unit is operated by the user.
Initialize
[Factory Set]
You can reset the player to its original factory
settings.
[Blu-ray Storage Clear]
Initializes the Blu-ray contents from the
connected USB storage.
Software
[Information]
Displays the current software version.
Blu-ray Disc Rating MPAA Rating
0 G
8 PG
13 PG-13
17 R
18 NC-17
255 Not restricted
Area Code
Enter the code of the area whose standards were
used to rate the DVD video disc, based on the list
on page 35.
Page 23
General Playback
Using [HOME] menu
The home menu appears when you press HOME (n).
Use
a
b
c
d
Playing a Disc
ert
1. Press B (OPEN/CLOSE), and place a disc on the
2. Press B (OPEN/CLOSE) to close the disc tray.
3. Press HOME (n).
4. Select [Movie] or [Music] using
5. Select [Blu-ray Disc], [DVD], [VR] or [Audio]
to select a category and press ENTER (b).
a/d
[Movie] - Plays video contents.
[Photo] - Plays photo contents.
[Music] - Plays audio contents.
[Setup] - Adjusts the system settings.
disc tray.
For the most Audio CD, BD-ROM and
DVD-ROM discs, playback starts automatically.
, and press
ENTER (b).
option using
, and press ENTER (b).
w/s
a/d
Note
,
yPlayback functions described in this manual
are not always available in every le and
media. Some functions can be restricted
depending on many factors.
yDepending on the BD-ROM titles, a USB
device connection may be needed for the
proper playback.
yUnnalized DVD VR format discs may not be
played in this player.
ySome DVD-VR discs are made with CPRM
data by DVD RECORDER. This unit cannot
support these kinds of discs.
Playing a file on a disc/USB
device
yui
This player can play video, audio and photo les
contained in the disc or USB device.
1. Insert a data disc on the tray or connect a USB
device. ( When you insert the USB device, the
USB option menu will be appeared to select for
[Movie], [Photo] or [Music]. )
2. Select [Movie], [Photo] or [Music] using
and press ENTER (b).
3. Select [Data] or [USB] option using
press ENTER (b).
4. Select a le using
(PLAY) or ENTER (b) to play the le.
d
w/s/a/d
Operating 23
a/d
, and
w/s
, and press
4
Operating
,
Page 24
24
Operating
Basic operations for video and audio content
To stop playback
Press Z (STOP) while playback.
To pause playback
Press M (PAUSE) while playback.
Press d (PLAY) to resume playback.
To play frame-by-frame (Video)
Press M (PAUSE) while movie playback.
Press M (PAUSE) repeatedly to play Frame-by-Frame
playback.
To scan forward or backward
Press c or v to play fast forward or fast reverse
during playback.
You can change the various playback speeds by
4
pressing c or v repeatedly.
Operating
To slow down the playing speed
While the playback is paused, press v repeatedly
to play various speeds of slow motion.
To skip to the next/previous
chapter/track/file
During playback, press C or V to go to the
next chapter/track/le or to return to the beginning
of the current chapter/track/le.
Press C twice briey to step back to the previous
chapter/track/le.
Basic operations for photo content
To play a slide show
Press d (PLAY) to start slide show.
To stop a slide show
Press Z (STOP) while slide show.
To pause a slide show
Press M (PAUSE) while slide show.
Press d (PLAY) to re-start the slide show.
To skip to the next/previous photo
While viewing a photo in full screen, press a or d
to go to the previous or next photo.
Using the disc menu
ero
To display the disc menu
The menu screen may be displayed rst after
loading a disc which contains a menu. If you want
to display the disc menu while playback, press DISC
MENU.
Use
w/s/a/d
menu items.
To display the Pop-up menu
Some BD-ROM discs contain Pop-up menu that
appears while playback.
Press TITLE/POP-UP while playback, and use
w/s/a/d
items.
buttons to navigate through
buttons to navigate through menu
Page 25
Operating 25
Resume playback
eroyt
u
The unit records the point where you pressed the
(STOP) depending on the disc.
Z
If “MZ (Resume Stop)” appears on the screen briey,
press d (PLAY) to resume playback (from the scene
point).
If you press Z (STOP) twice or unload the disc,
“Z(Complete Stop)” appears on the screen. The unit
will clear the stopped point.
Note
,
yThe resume point may be cleared when a
button is pressed (for example; 1 (POWER),
(OPEN/CLOSE), etc).
B
yOn BD-ROM discs with BD-J, the resume
playback function does not work.
yIf you press Z (STOP) once during BD-ROM
interactive title playback, the unit will be in
Complete Stop mode.
Advanced Playback
Repeat Playback
erotu
y
During playback, press REPEAT (h) repeatedly to
select a desired repeat mode.
Blu-ray discs/DVDs/ Video
A- – Selected portion will be repeated continually.
j
Chapter – The current chapter will be played
j
back repeatedly.
Title – The current title will be played back
j
repeatedly.
All – All the tracks or les will be played back
j
repeatedly.
To return to normal playback, press REPEAT (h)
repeatedly to select [O ].
Audio CDs/Audio les
A-B – Selected portion will be repeated
k
continually. (Audio CD only)
Track – The current track or le will be played
;
back repeatedly.
All – All the tracks or les will be played back
:
repeatedly.
All – All the tracks or les will be played
l:
back repeatedly in random order.
– The tracks or les will be played back in
l
random order.
To return to normal playback, press CLEAR.
Note
,
yIf you press V once during Repeat
Chapter/Track playback, the repeat playback
cancels.
yThis function may not work on some disc or
title.
4
Operating
Page 26
Operating26
Repeating a specific portion
eroty
This player can repeat a portion you have selected.
1. While playback, press REPEAT (h) to select
[A-] at the beginning of the portion you wish to
repeat.
2. Press ENTER (b) at the end of the portion. Your
selected portion will be repeated continually.
3.
To return to normal playback, press REPEAT (h)
repeatedly to select [O ].
Note
,
yYou cannot select a portion less than 3
seconds.
yThis function may not work on some discs
or titles.
Enlarge the playback image
4
Operating
eroyi
1. During playback or pause mode, press ZOOM to
display the [Zoom] menu.
2. Use red (R) or green (G) colored button to zoom
out or in the picture. You can move through the
zoomed picture using
3. To return to the normal picture size, press yellow
(Y ) colored button.
4. Press BACK (x) to exit the [Zoom] menu.
Note
,
On BD-ROM discs with BD-J, zoom function
does not work.
w/s/a/d
buttons.
Marker Search
eroy
You can start playback from up to nine memorized
points.
To enter a marker
1. While playback, press MARKER at the desired
point. The Marker icon appears on the TV screen
briey.
2. Repeat step 1 to add up to nine markers.
To recall a marked scene
1. Press SEARCH and the search menu appears on
the screen.
2. Press a number button to select a marker
number that you want to recall. Playback starts
from the marked scene.
To delete a Marker
1. Press SEARCH and the search menu appears on
the screen.
2. Press s to highlight a marker number.
Use
want to delete.
3. Press CLEAR and the marked scene is erased
from the search menu.
yThis function may not work depending on
yAll marked points are cleared if the title
yIf the total length of the title is less than 10
to select a marked scene that you
a/d
Note
,
discs, titles and le type.
is in complete stop (Z) mode, the title is
changed or if you unload the disc.
seconds, this function is not available.
Page 27
Operating 27
Using the search menu
eroy
Using search menu, you can easily to nd the point
where you want to start playback.
To search a point
1. During playback, press SEARCH to display the
search menu.
2. Press
forward or backward. You can select a point that
you want to skip by pressing and holding
a/d
To start playback from a marked
scene
1. Press SEARCH and the search menu appears on
the screen.
2. Press s to highlight a marker number.
Use
want to start playback.
3. Press ENTER (b) to start playback from the
marked scene.
This function may not work depending on
discs, titles and le type.
to skip the playback 15 seconds
a/d
button.
to select a marked scene that you
a/d
Note
,
Changing content list view
yui
On the [Movie], [Music] or [Photo] menu, you can
change the content list view.
Method 1
Press red (R) colored button repeatedly.
4
Operating
Method 2
1. On the content list, press INFO/DISPLAY (m) to
display the option menu.
2. Use
3. Press ENTER (b) to change the content list
view.
to select the [View Change] option.
w/s
Page 28
Operating28
Viewing content information
y
The player can display the content information.
1. Select a le using
2. Press INFO/DISPLAY (m) to display the option
menu.
3. Select the [Information] option using
press ENTER (b).
The le information appears on the screen.
While movie playback, you can display the le
information by pressing TITLE/POP-UP.
Note
,
The information displayed on the screen
may not correct comparing actual content
information.
Selecting a subtitle file
4
Operating
y
If the subtitle le name is dierent from the video
le name, you need to select the subtitle le on the
[Movie] menu before playing the Video.
1. Use
w/s/a/d
wish to play in the [Movie] menu.
2. Press ENTER (b).
w/s/a/d
to select the subtitle le you
Last Scene Memory
er
This unit memorizes the last scene from the last disc
.
, and
w/s
that is viewed. The last scene remains in memory
even if you remove the disc from the unit or switch
o the unit. If you load a disc that has the scene
memorized, the scene is automatically recalled.
Note
,
yLast Scene Memory function for a previous
disc is erased once a dierent disc is played.
yThis function may not work depending on
the disc.
yOn BD-ROM discs with BD-J, the last scene
memory function does not work.
yThis unit does not memorize settings of
a disc if you switch o the unit before
commencing to play it.
Press ENTER (b) again to deselect the subtitle
le. Selected subtitle le will be displayed when
you play the Video le.
Note
,
If you press Z (STOP) while playback, the
subtitle selection is cancelled.
Page 29
Operating 29
Options while viewing a photo
i
You can use various options during viewing a
photo in full screen.
1. While viewing a photo in full screen, press
INFO/DISPLAY (m) to display the option menu.
2. Select an option using
a Current photo/Total number of photos
– Use
b Slide Show – Press ENTER (b) to start or
pause slide show.
c Music Select – Select the background
music for the slide show (page 29).
d Music –Press ENTER (b) to start or pause
background music.
e Rotate – Press ENTER (b) to rotate the
photo clockwise.
f Zoom – Press ENTER (b) to display the
[Zoom] menu.
g Eect – Use
eect between photos in a slide show.
h Speed – Use
speed between photos in a slide show.
3. Press BACK(x) to exit the option menu.
to view previous/next photo.
a/d
a/d
a/d
.
w/s
to select a transition
to select a delaying
Listening to music while slide show
i
You can display photo les while listening to audio
les.
1. While viewing a photo in full screen, press
INFO/DISPLAY (m) to display the option menu.
2. Use
press ENTER (b) to display the [Music Select]
menu.
3. Use
ENTER (b).
4. Use
play.
Select g and press ENTER (b) to display the
upper directory.
When selecting music le from a folder
selection is not available. Only le selection is
available.
5. Use d to select [OK], and press ENTER (b) to
complete music selection.
to select [Music Select] option, and
w/s
to select a device, and press
w/s
to select a le or a folder you wish to
w/s
Note
,
4
Operating
Page 30
Operating30
On-Screen display
You can display and adjust various information and
settings about the content.
Displaying content information on-screen
eroy
1. While playback, press INFO/DISPLAY (m) to
show various playback information.
4
Operating
a Title – current title number/total number of
titles
b Chapter – current chapter number/total
number of chapters
c Time – elapsed playing time/total playback
time
d Audio – selected audio language or channel
e Subtitle – selected subtitle.
f Angle – selected angle/total number of
angles
g TV Aspect Ratio – selected TV aspect Ratio
h Picture Mode – selected picture mode
2. Select an option using
3. Use
4. Press BACK (x) to exit the On-Screen display.
yIf no button is pressed for a few seconds,
yA title number cannot be selected on some
yAvailable items may dier depending on
yIf an interactive Blu-ray Disc is playing back,
to adjust the selected option value.
a/d
Note
,
the on-screen display disappears.
discs.
discs or titles.
some setting information is displayed on
the screen but prohibited to be changed.
w/s
.
Playing from selected time
eroy
1. Press INFO/DISPLAY (m) during playback. The
time search box shows the elapsed playing
time.
2. Select the [Time] option and then input the
required start time in hours, minutes, and
seconds from left to right.
For example, to nd a scene at 2 hours, 10
minutes, and 20 seconds, enter “21020”.
Press
forward or backward.
3. Press ENTER (b) to start playback from selected
time.
This function may not work on some disc or
titles.
to skip the playback 60 seconds
a/d
Note
,
Page 31
Operating 31
Hearing a different audio
eroy
1. During playback, press INFO/DISPLAY (m) to
display the On-Screen display.
2. Use
3. Use
audio track or audio channel.
yDuring playback, you can also switch
ySome discs allow you to change audio
yImmediately after you have switched sound,
yOn BD-ROM disc, the multi audio format
to select the [Audio] option.
w/s
to select desired audio language,
a/d
Note
,
between the available audio language by
pressing AUDIO([) repeatedly.
selections only via the disc menu. In this
case, press TITLE/POP-UP or DISC MENU
button and choose the appropriate audio
from the selections on the disc menu.
there may be a temporary discrepancy
between the display and actual sound.
(5.1CH or 7.1CH) is displayed with [MultiCH]
in the on-screen display.
Selecting a subtitle language
eroy
1. During playback, press INFO/DISPLAY (m) to
display the On-Screen display.
2. Use
3. Use
4. Press BACK (x) to exit the On-Screen display.
yDuring playback, you can also select a
ySome discs allow you to change subtitle
to select the [Subtitle] option.
w/s
to select desired subtitle language.
a/d
Note
,
desired subtitle languge by pressing
SUBTITLE(]) repeatedly.
selections only via the disc menu. If this is
the case, press TITLE/POP-UP or DISC MENU
button and choose the appropriate subtitle
from the selections on the disc menu.
Watching from a different angle
er
If the disc contains scenes recorded at dierent
camera angles, you can change to a dierent
camera angle during playback.
1. During playback, press INFO/DISPLAY (m) to
display the On-Screen display.
2. Use
3. Use
4. Press BACK (x) to exit the On-Screen display.
to select the [Angle] option.
w/s
to select desired angle.
a/d
Changing the TV Aspect Ratio
eroy
You can change the TV aspect ratio setting while
playback.
1. During playback, press INFO/DISPLAY (m) to
display the On-Screen display.
2. Use
option.
3. Use
4. Press BACK (x) to exit the On-Screen display.
Even if you change the value of the [TV Aspect
Ratio] option in On-Screen display, the [TV
Aspect Ratio] option in the [Setup] menu is
not changed.
to select the [TV Aspect Ratio]
w/s
to select desired option.
a/d
Note
,
4
Operating
Page 32
Operating32
Changing the Picture Mode
eroy
You can change the [Picture mode] option while
playback.
1. During playback, press INFO/DISPLAY (m) to
display the On-Screen display.
2. Use
3. Use
4. Press BACK(x) to exit the On-Screen display.
Setting the [User setting] option
1. During playback, press INFO/DISPLAY (m) to
display the On-Screen display.
2. Use
3. Use
and press ENTER (b).
4
Operating
4. Use
options.
Select [Default] option then press ENTER (b) to
reset the all video adjustments.
5. Use
and press ENTER (b) to nish setting.
to select the [Picture Mode] option.
w/s
to select desired option.
a/d
to select the [Picture Mode] option.
w/s
to select the [User setting] option,
a/d
w/s/a/d
w/s/a/d
to adjust the [Picture Mode]
to select the [Close] option,
Changing subtitle code page
y
If the subtitle is displayed in broken letter, you can
change the subtitle code page to view the subtitle
le properly.
1. During playback, press INFO/DISPLAY (m) to
display the playback menu.
2. Use
3. Use
4. Press BACK (x) to exit the On-Screen display.
to select the [Code Page] option.
w/s
to select desired code option.
a/d
Page 33
Troubleshooting 33
Troubleshooting
General
Symptom Cause & Solution
The Power does not turn on. yPlug the power cord into the wall outlet securely.
The unit does not start
playback.
The angle cannot be changed. yMulti-angles are not recorded on the DVD Video being played.
Cannot play movie, photo or
music les.
The remote control does not
work properly.
The unit is plugged in, but the
power will not turn on or o.
The unit is not operating
normally.
yInsert a playable disc. (Check the disc type, colour system, and
regional code.)
yPlace the disc with the playback side down.
yPlace the disc on the disc tray correctly inside the guide.
yClean the disc.
yCancel the Rating function or change the rating level.
yThe les are not recorded in a format that the unit can play.
yThe unit does not support the codec of the movie le.
yThe remote control is not pointed at the remote sensor of the unit.
yThe remote control is too far from the unit.
yThere is an obstacle in the path of the remote control and the unit.
yThe batteries in the remote control are exhausted.
You can reset the unit as follows.
yUnplug the power cord, wait at least ve seconds, and then plug it in
again.
5
Troubleshooting
Page 34
5
Troubleshooting
Troubleshooting34
Picture
Symptom Cause & Solution
There is no picture. ySelect the appropriate video input mode on the TV so the picture
Picture noise appears yYou are playing a disc recorded in a color system that is dierent from
from the unit appears on the TV screen.
yConnect the video connection securely.
yCheck the [HDMI Color Setting] in the [Setup] menu is set to the
appropriate item that conforms to your video connection.
yYour TV may not suppot the resolution you have set on the player.
Change the resolution that your TV accepts.
yThe player’s HDMI OUT jack is connected to a DVI device that does
not support copyright protection.
your TV.
ySet the resolution which your TV accepts.
Sound
Symptom Cause & Solution
There is no sound or the sound
is distorted.
yConnect the audio connection securely.
yThe input source setting on the amplier or the connection to the
amplier is incorrect.
yThe unit is in scan, slow motion, or pause mode.
yThe sound volume is low.
yCheck that the connected amplier is compatible with audio format
output from the unit.
yThe unit’s HDMI OUT jack is connected to a DVI device. The DVI jack
does not accept audio signal.
yCheck the device connected to unit’s HDMI OUT jack is compatible
with audio format output from the unit.
Customer Support
You can update the Player using the latest software to enhance the products operation and/or add new
features. To obtain the latest software for this player (if updates have been made), please visit
http://www.lg.com/global/support or contact LG Electronics customer care center.
Open source software notice
To obtain the corresponding source code under GPL, LGPL, MPL and other open source licenses, please
visit http://opensource.lge.com. All referred license terms, warranty disclaimers and copyright notices are
available to download with the source code.
Page 35
Appendix 35
Troubleshooting
Area Code List
Choose an area code from this list.
Area Code Area Code Area Code Area Code
Afghanistan AF
Argentina AR
Australia AU
Austria AT
Belgium BE
Bhutan BT
Bolivia BO
Brazil BR
Cambodia KH
Canada CA
Chile CL
China CN
Colombia CO
Congo CG
Costa Rica CR
Croatia HR
Czech Republic CZ
Denmark DK
Ecuador EC
Egypt EG
El Salvador SV
Ethiopia ET
Fiji FJ
Finland FI
France FR
Germany DE
Great Britain GB
Greece GR
Greenland GL
Hong Kong HK
Hungary HU
India IN
Indonesia ID
Israel IL
Italy IT
Jamaica JM
Japan JP
Kenya KE
Kuwait KW
Libya LY
Luxembourg LU
Malaysia MY
Maldives MV
Mexico MX
Monaco MC
Mongolia MN
Morocco MA
Nepal NP
Netherlands NL
Antilles AN
New Zealand NZ
Nigeria NG
Norway NO
Oman OM
Pakistan PK
Panama PA
Paraguay PY
Philippines PH
Poland PL
Portugal PT
Romania RO
Russian
Federation RU
Saudi Arabia SA
Senegal SN
Singapore SG
Slovak Republic SK
Slovenia SI
South Africa ZA
South Korea KR
Spain ES
Sri Lanka LK
Sweden SE
Switzerland CH
Taiwan T W
Thailand TH
Turkey TR
Uganda UG
Ukraine UA
United States US
Uruguay UY
Uzbekistan UZ
Vietnam VN
Zimbabwe ZW
6
Appendix
Page 36
Appendix36
Language Code List
Use this list to input your desired language for the following initial settings: [Disc Audio],
[Disc Subtitle] and [Disc Menu].
Language Code Language Code Language Code Language Code
Lithuanian 7684
Macedonian 7775
Malagasy 7771
Malay 7783
Malayalam 7776
Maori 7773
Marathi 7782
Moldavian 7779
Mongolian 7778
Nauru 7865
Nepali 7869
Norwegian 7879
Oriya 7982
Panjabi 8065
Pashto, Pushto 8083
Persian 7065
Polish 8076
Portuguese 8084
Quechua 8185
Rhaeto-Romance 8277
Rumanian 8279
Russian 8285
Samoan 8377
Sanskrit 8365
Scots Gaelic 7168
Serbian 8382
Serbo-Croatian 8372
Shona 8378
6
Appendix
Afar 6565
Afrikaans 6570
Albanian 8381
Ameharic 6577
Arabic 6582
Armenian 7289
Assamese 6583
Aymara 6588
Azerbaijani 6590
Bashkir 6665
Basque 6985
Bengali; Bangla 6678
Bhutani 6890
Bihari 6672
Breton 6682
Bulgarian 6671
Burmese 7789
Byelorussian 6669
Chinese 9072
Croatian 7282
Czech 6783
Danish 6865
Dutch 7876
English 6978
Esperanto 6979
Estonian 6984
Faroese 7079
Fiji 7074
Finnish 7073
French 7082
Frisian 7089
Galician 7176
Georgian 7565
German 6869
Greek 6976
Greenlandic 7576
Guarani 7178
Gujarati 7185
Hausa 7265
Hebrew 7387
Hindi 7273
Hungarian 7285
Icelandic 7383
Indonesian 7378
Interlingua 7365
Irish 7165
Italian 7384
Japanese 7465
Kannada 7578
Kashmiri 7583
Kazakh 7575
Kirghiz 7589
Korean 7579
Kurdish 7585
Laothian 7679
Latin 7665
Latvian, Lettish 7686
Lingala 7678
Sindhi 8368
Singhalese 8373
Slovak 8375
Slovenian 8376
Spanish 6983
Sudanese 8385
Swahili 8387
Swedish 8386
Tagalog 8476
Tajik 8471
Tamil 8465
Telugu 8469
Thai 8472
Tonga 8479
Turkish 8482
Turkmen 8475
Twi 8487
Ukrainian 8575
Urdu 8582
Uzbek 8590
Vietnamese 8673
Volapük 8679
Welsh 6789
Wolof 8779
Xhosa 8872
Yiddish 7473
Yoruba 8979
Zulu 9085
Page 37
Audio Output Specifications
Appendix 37
Jack/Setting
Source
Dolby Digital
Dolby Digital Plus
Dolby TrueHD
DTS
DTS-HD
Linear PCM 2ch
Linear PCM 5.1ch
Linear PCM 7.1ch
*1 The secondary and interactive audio may not
be included in the output bitstream if [HDMI]
option is set to [Primary Pass-Thru]. (Except
LPCM Codec : the output always includes
interactive and secondary audio.)
*2 This player automatically selects the HDMI audio
according to the decoding capability of the
connected HDMI device even though [HDMI]
option is set to [Primary Pass-Thru].
*3 If the [HDMI] option is set to [DTS re-encode],
the audio output is limited to 48 kHz and 5.1Ch.
If the [HDMI] option is set to [DTS re-encode],
the DTS Re-encode audio is outputted for BDROM discs, and the original audio is outputted
for the other discs (like [Primary Pass-Thru]).
Analog
2CH Output
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM 2ch
PCM Stereo PCM
PCM 2ch PCM 2ch DTS Dolby Digital
PCM 2ch PCM 2ch DTS Dolby Digital Plus
PCM 2ch PCM 2ch DTS Dolby TrueHD
PCM 2ch PCM 2ch DTS DTS
PCM 2ch PCM 2ch DTS DTS-HD
PCM 2ch PCM 2ch DTS Linear PCM 2ch
PCM 2ch PCM 5.1ch DTS Linear PCM 5.1ch
PCM 2ch PCM 7.1ch DTS Linear PCM 7.1ch
HDMI OUT
Multi-Ch
DTS Re-encode
yThe audio is outputted as PCM 48 kHz/16 bit for
MP3/WMA le and PCM 44.1kHz/16 bit for Audio
CD while playback.
yYou must select an audio output and a maximum
sampling frequency that your Amplier (or AV
receiver) accepts using, [HDMI] and [Sampling
Freq.] options on the [Setup] menu (see page 20).
yWith digital audio connection (HDMI), Disc Menu
button sounds of BD-ROM may not be heard if
the [HDMI] option is set to [Primary Pass-Thru].
yIf the audio format of the digital output does
not match the capabilities of your receiver, the
receiver will produce a strong, distorted sound
or no sound at all.
yMulti-channel Digital Surround Sound via digital
connection can only be obtained if your receiver
is equipped with a Digital Multi-channel decoder.
Primary Pass-Thru
*3
*1 *
2
6
Appendix
Page 38
Appendix38
Trademarks and Licenses
Blu-ray Disc™, Blu-ray™, BONUSVIEW™ and
the logos are trademarks of the Blu-ray Disc
Association.
Java is a trademark of Oracle and/or its aliates.
HDMI, the HDMI logo and High-Denition
Multimedia Interface are trademarks or registered
trademarks of HDMI Licensing LLC in the United
States and other countries.
Manufactured under license under U.S. Patent
Nos: 5,956,674; 5,974,380; 6,487,535 & other U.S.
and worldwide patents issued & pending. DTS,
the Symbol, & DTS and the Symbol together are
registered trademarks & DTS 2.0+Digital Out is a
trademark of DTS, Inc. Product includes software.
© DTS, Inc. All Rights Reserved.
“DVD Logo” is a trademark of DVD Format/Logo
Licensing Corporation.
“AVCHD” and the “AVCHD” logo are trademarks of
Panasonic Corporation and Sony Corporation.
6
Appendix
Manufactured under license from Dolby
Laboratories. Dolby and the double-D symbol
are trademarks of Dolby Laboratories.
Page 39
Specifications
General
Power requirements Refer to main label on the rear panel.
Power consumption 13 W
Dimensions (W x H x D) Approx. 360 x 40 x 190 mm (14.2 x 1.6 x 7.5 inches)
Net Weight (Approx.) 1.3 kg (2.9 lbs)
Operating temperature 5 °C to 35 °C (41 °F to 95 °F)
Operating humidity 5 % to 90 %
Outputs
VIDEO OUT 1.0 V (p-p), 75 Ω, sync negative, RCA jack x 1
HDMI OUT (video/audio) 19 pin (Type A, HDMI™ Connector)
ANALOG AUDIO OUT 2.0 Vrms (1 kHz, 0 dB), 600 Ω, RCA jack (L, R) x 1
System
Laser Semiconductor laser
Wavelength 405 nm / 650 nm
Signal system Standard NTSC color TV system
Frequency response 20 Hz to 20 kHz (48 kHz, 96 kHz, 192 kHz sampling)
Signal-to-noise ratio More than 90 dB (ANALOG OUT connectors only)
Harmonic distortion Less than 0.02%
Dynamic range More than 95 dB
Bus Power Supply (USB) DC 5 V 0 500 mA
yDesign and specications are subject to change without notice.
Appendix 39
6
Appendix
Page 40
Appendix40
Maintenance
Handling the Unit
When shipping the unit
Please save the original shipping carton and
packing materials. If you need to ship the unit, for
maximum protection, re-pack the unit as it was
originally packed at the factory.
Cleaning the unit
To clean the player, use a soft, dry cloth. If the
surfaces are extremely dirty, use a soft cloth lightly
moistened with a mild detergent solution. Do not
use strong solvents such as alcohol, benzine, or
thinner, as these might damage the surface of the
unit.
Keeping the exterior surfaces clean
yDo not use volatile liquids such as insecticide
spray near the unit.
yWiping with strong pressure may damage the
surface.
yDo not leave rubber or plastic products in
contact with the unit for a long period of time.
Maintaining the Unit
The unit is a high-tech, precision device. If the
optical pick-up lens and disc drive parts are dirty
6
or worn, the picture quality could be diminished.
Appendix
For details, please contact your nearest authorized
service center.
Notes on Discs
Handling Discs
Do not touch the playback side of the disc. Hold
the disc by the edges so that ngerprints do not
get on the surface. Never stick paper or tape on the
disc.
Storing Discs
After playing, store the disc in its case. Do not
expose the disc to direct sunlight or sources of heat
and never leave it in a parked car exposed to direct
sunlight.
Cleaning Discs
Fingerprints and dust on the disc can cause poor
picture quality and sound distortion. Before playing,
clean the disc with a clean cloth. Wipe the disc from
the center to out.
Do not use strong solvents such as alcohol,
benzine, thinner, commercially available cleaners,
or anti-static spray intended for older vinyl records.
Page 41
Warranty 41
LG Electronics, Inc. Limited Warranty - USA
This LG Electronics product, will be repaired or replaced with refurnished units, at LG’s option, if it proves to
be defective in material or workmanship, under normal use, during the warranty period (“Warranty Period”)
listed below, eective from the date (“Date of Purchase”) of original consumer purchase of the product. This
warranty is good only to the original purchaser of the product and eective only when used in the United
States, excluding U.S. Territories.
WARRANTY PERIOD:
LABOR: 90 Days from the Date of
Purchase.
PARTS: One Year from the Date of
Purchase.
yParts replaced are warranted for the
remaining portion of the original
warranty period
THIS WARRANTY IS IN LIEU OF ANY OTHER WARRANTIES, EXPRESS OR IMPLIED, INCLUDING WITHOUT
LIMITATION, ANY WARRANTY OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. TO
THE EXTENT ANY IMPLIED WARRANTY IS REQUIRED BY LAW, IT IS LIMITED IN DURATION TO THE
EXPRESS WARRANTY PERIOD ABOVE. LG ELECTRONICS WILL NOT BE LIABLE FOR ANY INCIDENTAL,
CONSEQUENTIAL, INDIRECT, SPECIAL OR PUNITIVE DAMAGES OF ANY NATURE, EVEN IF ADVISED
OF THE POSSIBILITY OF SUCH DAMAGES, INCLUDING WITHOUT LIMITATION, LOST REVENUES OR
PROFITS, LOST OR CORRUPTED PROGRAMMING OR DATA, OR ANY OTHER DAMAGE WHETHER BASED
IN CONTRACT, TORT OR OTHERWISE. Some states do not allow the exclusion or limitation of incidental
or consequential damages or limitation on how long an implied warranty lasts, so the above exclusion or
limitation may not apply to you. This warranty gives you specic legal rights and you may also have other
rights that may vary from state to state.
THIS LIMITED WARRANTY DOES NOT APPLY TO:
yDamages or operating problems that result from shipping, installation, adjustment of user controls,
calibration, maintenance or failure to maintain, or separate system components; and
yDamages or operating problems that result from normal wear and tear, misuse, abuse, operation outside
environmental specications or contrary to the requirements or precautions in the Operating Guide,
accident, lightning strikes or other natural causes, unauthorized modication or alteration, incorrect
electrical current or voltage, reception problem caused by inadequate home antenna or faulty antenna
connections, computer software, institutional or commercial use, or other causes not arising out of defect
in material or workmanship.
Therefore, the cost of repair or replacement of such defective product shall be borne by the consumer.
CUSTOMER INTER-ACTIVE CENTER NUMBERS:
For nearest Authorized Service Center,
Where to buy, Product Assistance, or
Customer Assistance
HOW SERVICE IS HANDLED:
Call 1-800-243-0000 for instructions on getting the defective
unit repaired or replaced.
Please retain dated sales receipt and your box to return the
unit to LG for repair or replacement.
Shipping both ways will be paid by LG during the Warranty
Period. After the Warranty Period, you pay inbound shipping
charges and LG pays return shipping charges.
Visit our web site at: http://us.lgservice.com
Call 1-800-243-0000 (24 hours a day, 365 days per year) and
select appropriate options from the menu.
7
Warranty
LG ELECTRONICS U.S.A., INC.
1000 SYLVAN AVENUE
ENGLEWOOD CLIFFS, NJ
Page 42
Printed in China
LG Customer Information Center
1-800-243-0000 USA, Consumer
1-888-865-3026 USA, Commercial
Register your product Online!
www.lg.com
Loading...