LG BD430 User Manual

LCD Projector

Model

BD430 BD450 BD460 BD470

Owner's Manual

P/N: 4100411501 Rev. B www.lg.com

Safety Instructions

Please take note of the safety instructions to prevent any potential accident or misuse of the projector.

WARNING/CAUTION

AVERTISSEMENGT

Warning:The lightning ash

with arrowhead symbol, within an equilateral triangle,is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s enclosure that may be

of sufcient magnitude to constitute a

risk of electric shock to persons.

Caution: The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the appliance.

WARNING/CAUTION

- TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.

WARNING: This product contains chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.

Wash hands after handling.

Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions.

Indoor Installation

WARNING

• Do not place the projector in direct

sunlight or near heat sources such as

radiators, res, stoves, etc.

- This may cause a re.

• Do not place ammable materials such

as aerosols near the projector.

- This may cause a re.

• Do not allow your children to cling to or

climb up to the projector.

- The projector may fall down and cause personal injury or death.

• Do not place the projector directly on a

carpet, rug or place where ventilation is restricted such as a book shelf or closet.

- This may cause the projector's internal

temperature to rise and cause a re.

• Do not place the projector close

to sources of steam or oil such as a

humidier or kitchen counter.

- This may cause a re hazard or an

electric shock

• Do not place the projector where it might

be exposed to excessive dust.

- This may cause a re.

• Do not use the projector in a damp place

such as a bathroom where it is likely to get wet.

- This may cause a re or an electric

shock.

• Do not allow a tablecloth or curtain to

block the vents.

- This may cause the internal temperature

of the projector to rise and cause a re.

• The distance between the projector and

the wall should be more than 30 cm for ventilation purposes.

- Otherwise, this may cause the internal temperature of the projector to rise and

cause a re.

CAUTION

• When installing the projector on a table,

be careful not to place it near the edge.

- The projector may fall causing injury to persons or damage to the projector. Make sure that you use a stand suitable

for the size of projector.

• Turn off the projector, disconnect the

power supply and remove all connec tions before moving the projector.

- A damaged cord may cause a re or an

electric shock.

• Do not install the projector on an

unstable or vibrating surface such as a vibrating shelf or tilted surface.

- It may fall and cause injury.

• Be careful not to tip the projector over

when connecting external devices to the projector.

- This may cause injury to persons or damage to the projector

Safety Instructions

POWER

WARNING

• The earth wire should be connected.

- Inappropriate earth grounding may cause damage to the projector or an electric shock when there is an electrical surge.If the projector must be installed at a place where earth grounding is not possible, purchase a circuit breaker and connect the projector to its wall outlet.Do not ground the projector to the gas pipe, water pipe, lightning rod, or telephone line, etc.

• The power plug should be fully inserted

into the wall outlet.

- Unstable connection may cause a re.

• Do not place heavy objects on the

power cord or place the cord underneath

the projector.- This may cause a re or

an electric shock.

• Never touch the power plug with a wet

hand.

- This may cause an electric shock.

• Do not connect too many devices to the

same power extension.

- Overheating may cause a re.

• Remove dust or contaminants around

power plug pins or wall outlets.

- This may cause a re.

• To turn off the main power, remove the

power plug, which should be positioned so it is easy to access for operation.

Safety Instructions

CAUTION

• Hold the plug rmly when unplugging.

- A broken wire in the cord may cause a

re.

• Ensure the power cord or plug is not damaged, modied, severely bent,

twisted, pulled, sandwiched or heated. Do not use a loose wall outlet.

- This may cause a re or an electric

shock.

• Keep the power cord away from any

heating devices.

- The cord coating may melt and cause an electric shock.

• Place the projector where people will

not trip over or tread on the power cord or plug to protect the power cord and plug from any damage.

- This may cause a re hazard or an

electric shock.

• Do not turn the projector on or off by

plugging in the power plug or unplugging it from the wall outlet. (Do not use the power plug as a switch.)

- This may cause an electric shock or damage to the projector.

• Do not insert a conductor into the other

side of the wall outlet while the power plug is inserted into the wall outlet. In addition, do not touch the power plug immediately after it is disconnected from the wall outlet.

- This may cause an electric shock.

• Use only the ofcial power cord which

is provided by LG Electronics, Inc. Do not use other power cords.

- This may cause a re or an electric

shock.

USING

WARNING

• Do not place anything containing liquid, such as a vase, owerpot, cup,

cosmetics, chemicals, decorations or candles, etc., on top of the projector.

- Possible re, electric shock, or falling

may cause physical injury.

• In the event that there is a big impact to

the projector or the cabinet is damaged, switch it off, unplug it from the wall outlet

and contact an authorized service

center.

- Otherwise, this may cause a re or an

electric shock.

• Do not insert pieces of metal such

as coins, hairpins or metal debris, nor

ammable materials such as paper or

matches into the projector.

- This may cause a re or an electric

shock.

• In the event that liquid or a foreign

object falls into the projector, please switch it off and unplug it from the wall outlet and contact an LG Electronics Service Center.

- Otherwise, this may cause a re or an

electric shock.

• When replacing a battery of the remote

control, make sure a child does not swallow the battery. Keep the battery out of reach of children.

- In the case of a battery being swallowed by a child, please consult a doctor immediately.

• Do not remove any covers except for

the lens cap. There is a high risk of electric shock.

• Do not look directly into the lens when

the projector is in use.

Safety InstructionsSafety Instructions

• When the lamp is on or has just been

turned off, avoid touching the air vent or lamp because these will be very hot.

• If there is a gas leak, do not touch

the wall outlet. Open the window for ventilation.

- A spark may cause a re or burn.

• Always open the lens door and remove

the lens cap when the projector lamp is on.

• Never touch the projector or power cord

during thunder or lightning.

- This may cause an electric shock.

• Do not use the projector near an

electronic device which generates a

strong magnetic eld.

• Store the vinyl envelope used to pack

the projector in a safe place away from children.

- It could cause suffocation if used improperly.

• Do not keep your hand on the projector

for a long time when it is running.

• When you play a game by connecting

a game console to a projector, it is recommended that you maintain a distance of more than four times the diagonal length of the screen.

• Make sure that the length of connecting

cable is long enough. Otherwise, the product may fall causing personal injury or damage to the product.

CAUTION

• Do not place a heavy object on the

projector.

- It may fall down and cause physical injury.

• Be careful to prevent the lens from

heavy impact during transportation.

• Do not touch the lens. The lens may be

damaged.

• Do not use any sharp tools on the

projector such as a knife or hammer, because this may damage the casing.

• In the event that no image appears

on the screen, switch the projector off, unplug it from the wall outlet and contact

an authorized service center.

- Otherwise, this may cause a re or an

electric shock.

• Do not drop an object onto the projector

or apply heavy pressure to it.

- This may cause injury to persons or damage to the projector.

• The distance between your eyes and

the screen must be around 5 - 7 times the diagonal length of the screen.

- If you watch the screen at a close distance for a long time, your eye sight may become worse.

Safety Instructions

Cleaning Others

WARNING WARNING

• Do not spray the projector with water

when cleaning. Do not allow water to go into the projector or do not allow it to get wet.

- This may cause a re or an electric

shock.

• When there is smoke or a strange smell

coming out from the projector or a foreign object falls into the projector, please switch it off and unplug it from the power outlet and contact an LG Electronics Service Center.

- If not, this may cause a re or an electric

shock.

• Use an air spray or soft cloth or cotton

swab moistened with a lens cleaning chemical or alcohol to remove dust or stains on the front projection lens.

CAUTION

• Contact your seller or the Service

Center once a year to clean the internal parts of the projector.

- If you do not clean the contaminated interior of the projector for a long time,

there may be a re or damage to the

projector.

• When cleaning plastic parts such as

the projector case, unplug the power

rst and wipe with a soft cloth. Do not

spray with water or wipe with a wet cloth. When cleaning the plastic parts, such as the projector case, do not use cleanser, automobile or industrial shiner,

abrasive or wax, benzene, alcohol, etc.,

which can damage the product.

- This can cause re, electric shock or

product damage (deformation, corrosion and damage).

• Only a qualied technician can

disassemble or modify the projector. For inspection, adjustment, or repair, contact your seller or the Service Center.

- Otherwise, this may cause a re or an

electric shock.

• Dispose of the used battery properly.

- Otherwise, this may result in explosion

or re.

• The correct method of disposal may

vary depending on your country or region. Dispose of the battery pack according to the appropriate instructions.

• Do not throw or disassemble the battery.

- Otherwise, this may result in re or

explosion due to damage to the battery.

• Always use batteries approved and certied by LG Electronics.

- Otherwise, this may result in re or

explosion.

• Store the battery away from metallic

objects, such as keys and paper clips.

• Excess current may cause a rapid increase in temperature, resulting in re

or burns.

• Do not store the battery near any heat

source, such as a heater.

- This may result in re or damage the

product.

• Do not store it at temperatures higher

than 60°C or in high humidity.

Safety Instructions

• Keep the battery out of reach of

children.

- This may result in personal injury or damage to the product.

• Make sure that the battery is installed

correctly.

• Incorrect battery replacement may cause re.

CAUTION

• Do not mix new batteries with old

batteries.

- This may cause a re or an electric

shock caused by overheating and leakage.

• Unplug the power cord if the projector

is not used for a long period.

- Accumulated dust may cause overheating, an electric shock from

corroded insulation and a re from an

electrical surge.

• Only use the specied type of battery.

- Otherwise, this may cause an electric shock caused by overheating and leakage.

FCC NOTICE

• Warning - Class B (b) For a Class B Digital device or peripheral, the instructions furnished the user shall include the following or

similar statement, placed in a prominent

location in the text of the manual:

NOTE: This equipment has been tested and found to comply with the limits for

a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can

radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment and receiver.

- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.

- Consult the dealer or an experienced radio/TV technician for help.

Safety Instructions

Disposal of your old appliance

1. When this crossed-out wheeled bin symbol is attached to a product it means the product is covered by the European Directive 2002/96/EC.

2. All electrical and electronic products should be disposed of separately from the municipal waste stream through designated collection facilities appointed by your government or your local authorities.

3. The correct disposal of your old appliance will help prevent potential negative consequences for the environment and human health.

4. For more detailed information about disposal of your old appliance, please

contact your city ofce, waste disposal

service or the shop where you purchased the product.

Disposal of waste batteries/accumulators

1. When this crossed-out wheeled bin symbol is attached to batteries/ accumulators of Your product it means they are covered by European Directive 2006/66/EC.

2. This symbol may be combined with chemical symbols for mercury(Hg), cadmium(Cd) or lead(Pb) if the battery Contains more that 0.0005% of mercury,

0.002% of cadmium or 0.004% of lead.

3. All batteries/accumulators should be disposed separately from the municipal waste stream via designated collection facilities appointed by the government or the local authorities.

4. The correct disposal of Your old batteries/accumulators will help to prevent potential negative consequences for the environment, animal and human health.

5. For more detailed information about disposal of Your old batteries/ accumulators, please contact Your city

ofce, waste disposal service or the

shop where You purchased the product.

Licenses

Supported licenses may differ by model. For more information about licenses, visit www.lg.com.

HDMI, the HDMI logo and High-Denition Multimedia

Interface are trademarks or registered trademarks of HDMI Licensing LLC.

NOTE

• Image shown may differ from your projector.

• Your projector’s OSD (On Screen Display) may differ slightly from that

shown in this manual.

Safety Instructions 2 Licenses 9 Table of Contents 10 Statement 11 Part names and functions 12

Front 12 Back 12 Bottom 12 Rear terminal 13 Top control and indicators 14 Remote control 15 Remote control battery installation

17 Operation range 17 Adjustable foot 17

Installation 18

Positioning the projector 18 Connect to computer (Digital and analog RGB) 19 Connect to video equipment (Video, S-Video,Component,HDMI) 20 Connecting to Audio equipment 21 Connecting to the AC power cord 22

Basic operation 23

Turning on the projector 23 Turning off the projector 24 How to operate the On Screen Menu

25 Menu bar 26 Zoom and focus adjustment 27 Auto setup function 27 Keystone 27 Audio adjustment 28 Remote control operation 29

Computer input 31

Select input source (RBG 1/RGB 2) 31 Computer system select 32 Auto PC adjustment 33

Manual adjustment via PC 34 Image select 35 Image adjust 36

Screen size adjust 37

Video Input 38

Select input source

(HDMI/Component/S-video/Video) 38 Video system select 39 Image select 40 Image adjust 41

Screen size adjust 42

Option 43

Information 51 Maintenance 52

POWER/TEMP indicator 52

Cleaning the lter 53

Attaching the Lens Cap 54 Cleaning the lens 54 Cleaning the projector’s cabinet 54 Replacing the lamp 55

Appendix 57

Troubleshooting 57 Indicator and projector state 59 Compatible Signal 60

Conguration of terminals 61 Technical Specications 62

Accessories 63

Content of hazardous substances and

elements 63 Dimensions 64 PIN code memorandum 64 RS232 Control Method 65

Statement

Note:



• The on screen menu and pictures in the manual may slightly differ from the real product.

• The manual is subject to change without prior notice.

Part names and functions

Front

Back

① ②

⑫ ⑩

③④

⑪

Air lter cover

①

Remote receiver

②

Zoom ring

⑦

⑤

⑥

⑥⑧ ⑨

③

Projector lens

④

Lens cap (with string)

⑤

Speaker

⑥

Focus ring

⑦

Power cord connector

⑧

Safety lock

⑨

Terminals and connectors

⑩

Top control and indicators

⑪

Lamp cover

⑫

Bottom

⑭

⑬

Adjustable foot

⑬

Foot adjusting Button

⑭

Rear terminal

Part names and functions

① ② ③ ④ ⑤

S-VIDEO

AUDIO OUT

AUDIO IN

MONO

Pb/Cb

Pr/Cr

VIDEO/Y

⑧ ⑨

AUDIO OUT

①

- Connect to external audio amplier.

- Connect the output audio signals from ②, ⑦ and ⑧to this port.

Note: The resistance of the external audio amplier should be over 47kΩ, or an earphone with lower resistance may cause audio distortion.

AUDIO IN(Video Mono L/R)

②

- Connect the audio output signal from video equipment connected to ③or

For a mono audio signal (a single audio jack),

④

to this port.

connect it to L(MONO) jack.

VIDEO/Y, Pb/Cb, Pr/Cr

③

- Connect the component signals to these jacks.

- Connect the composite signals to the VIDEO/ Y jack.

⑥ ⑦

RGB IN 1

RGB IN 2

RGB OUT

⑤

RGB IN 1

RS-232 C

HDMI

Used to connect a computer output.

RS-232C

⑥

When using RS-232C to control the projector, please connect the serial control line to this terminal.

HDMI

⑦

Used to connect the HDMI digital output.

AUDIO IN (PC)

⑧

Connect the audio output signal from computer connected to ⑤ or ⑨ to this jack.

RGB IN 2/RGB OUT

⑨

- Used to connect the computer output.

- Used to output the analog signals from ⑤(RGB IN 1) to the other monitor.

S-VIDEO

④

Used to connect the S-video output of video equipment.

Part names and functions

AUTO

INPUT

Top control and indicators

Top control Indicator (Top panel)

①

②

④

MENU button

①

To open or close the on screen menu.

AUTO button

②

To perform various settings congured

automatically, including the input source search function, auto keystone function and auto PC adjust function.

OK button

③

- Enter on screen menu.

- Execute the selected item.

- Expand or compress the image in the Digital Zoom Mode.

▲▼◄► (VOLUME +/-) buttons

④

- Select an item or adjust the value in the on screen menu.

- Adjust the volume level (◄►buttons).

- Move the image in the Digital Zoom +/- mode.

③

⑥

To select an input source.

⑦

- Lights red when the projector is in stand-by mode.

- Lights green during operations.

- Blinks green in the Power management mode.

- Blinks orange while projector is cooling down after powered off.

- Lights orange when the internal temperature of projector is too high during operations.

⑧

- Turns red when the life of the projection lamp draws to an end.

- Blinks red when lamp turning-on error.

⑤

⑥ ⑦ ⑧

INPUT button

POWER/TEMP indicator

LAMP REPLACE indicator

POWER button

⑤

To turn on/off the projector.

Remote control

2930058502

①

Part names and functions

HDMI button

①

②

③

Select HDMI input source.

RGB2 IN button

②

Select RGB2 as RGB input.

④

⑥ ⑧

⑩

⑫

⑭

⑤

⑦ ⑨

⑪

⑬ ⑮

POWER button

③

Turn the projector on or off .

RGB1 button

④

Select RGB1 input source.

RGB2 OUT button

⑤

Enable RGB2 as monitor out.

VIDEO button

⑥

Select VIDEO input source.

MENU button

⑦

Open or close the on screen menu.

S-VIDEO button

⑧

Select S-Video input source.

COMPONENT button

⑨

Select the component input source.

▲▼◄► button

⑩

- Select an item or adjust the value in the on screen menu.

- Move the image in Digital zoom + mode.

OK button

⑪

Access the menu or select an item in the menu.

KEYSTONE button

⑫

Calibrate keystone distortion.

To ensure safe operation, observe the following precautions:

- Do not bend, drop or expose the remote control to moisture or heat.

- For cleaning, use a soft dry cloth. Do not

apply benzene, thinner, splay, or any

other chemicals.

BLANK button

⑬

Hide the on screen menu.

AUTO button

⑭

Enter the AUTO setup mode.

STILL button

⑮

Still the projected image.

Please refer to next page for other buttons.

2930058502

Part names and functions

MUTE button

⑯

Mute the sound.

TIMER button

⑰

Enable the timer function.

DZOOM + button

⑱

Select the digital zoom + mode.

VOLUME + button

⑲

Increase the volume.

DZOOM - button

⑳

Select the digital zoom - mode.

⑯ ⑰

⑱ ⑲ ⑳

VOLUME - button

Decrease the volume.

LAMP button Select a lamp mode.

SLEEP button

Turn off the projector in a specied time.

16:9 button

Select 16:9 on screen display.

PICTURE button Select image mode.

4:3 button

Select 4:3 on screen display.

PATTERN button Select a test pattern picture.

INFO button Operate the information function.

RATIO button

Select your required screen mode.

Part names and functions

AUTO

INPUT

POWER

16.4' (5 m)

30°

Remote control

30°

Remote control battery installation

1. Open the battery compartment lid.

To ensure safe operation, please observe the following precautions:

● Use two (2) AAA or LR03 type alkaline batteries.

● Always replace batteries in sets.

● Do not use a new battery with a used battery.

● Avoid contacting with water or liquid matter.

● Do not expose the remote control to moisture or heat.

● Do not drop the remote control.

● If the battery has leaked on the remote control, carefully wipe the case clean and

install new batteries.

● Risk of explosion if a battery is replaced by an incorrect type.

● Dispose of used batteries according to the instructions.

Operation range

Point the remote control toward the projector when pressing any button. The maximum operating range for the remote control is about 5 meters and 60 degrees.

2. Install new batteries into the compartment.

For correct polarity ( + and – ) , be sure battery terminals are in contact with pins in the compartment

3. Re-cover the compartment lid.

Adjustable foot

Projection angle can be adjusted up to 10.0 degree with the Adjustable foot. Lift the fore body of the projector, and press the Foot adjusting Button on the front foot to release it. Rotate the Adjustable foot to adjust the height and tilt angle.

Adjustable foot

Keystone distortion of projected image can be corrected by auto settings or manually remote control or menu operation.

Installation

Positioning the projector

For projector positioning, see the gures below. The projector should be set perpendicularly to the plane

of the screen.

√ Note:

● The brightness in the room has a great inuence on picture quality. It is recommended to limit the ambient lighting in order to get the best image.

● All measurements are approximate and may vary from the actual sizes.

For XGA models

A:B=9:1

5.960m

4.464m

2.967m

1.172m 100”

40”

For WXGA models

A:B=49:1

6.363m

4.767m

3.171m

1.255m 100”

40”

8.943m

150”

9.556m

150”

10.737m

200”

11.478m

200”

300”

Zoom (max)

300”

Zoom (max)

Inch Diagonal

Zoom (min)

Inch Diagonal

Zoom (min)

Screen size

300”

(WxH)mm 4:3 aspect ratio

Maximum 1.172m 2.967m 4.464m 5.960m 8.943m

Minimum 1.411m 3.567m 5.363m 7.159m 10.737m

Center

Screen size

300”

(WxH)mm 16:10 aspect ratio

Maximum 1.255m 3.171m 4.767m 6.363m 9.556m

Minimum 1.511m 3.811m 5.728m 7.645m 11.478m

Center

40" 100" 150" 200" 300"

813x610 2032x1524 3048x2286 4064x3048 6096x4572

40" 100" 150" 200" 300"

862 x 538 2154x1346 3231x2019 4308x2692 6462x4039

Connect to computer (Digital and analog RGB)

HDMI

RGB OUT

VIDEO/Y

Pr/Cr

AUDIO IN

AUDIO OUT

Pb/Cb

S-VIDEO

RGB IN 2

RGB IN 1

RS-232C

MONO

Cables used for connection ( *Cables are not supplied with the projector.) RGB cable (1) Serial cable* HDMI cable*

Installation

RGB intput

RGB output

RGB cable RGB cable

RGB output RGB 1 input

Serial port

HDMI output

Serial cable HDMI cable

Control port

HDMI

Unplug the power cords of both the projector and external equipment from the AC outlet before connecting the cables.

Installation

HDM I

RGB OUT

VIDEO/Y

Pr/Cr

AUDIO IN

AUDIO OUT

Pb/Cb

S-VIDEO

RGB IN 2

RGB IN 1

RS-232 C

MONO

Connect to video equipment (Video, S-Video,Component,HDMI)

Cables used for connection (*Cables are not supplied with the projector.) Video cable (RCA*1 )* S-Video cable * HDMI cable * Component cable(RCA*3) *

Component video output

RCA cable

Y-Pb/Cb Pr/Cr

Video output S-video output

Video cable

Video

S-video cable

S-video

HDMI output

HDMI cable

HDMI

Unplug the power cords of both the projector and external equipment from the AC outlet before connecting the cables.

Connecting to Audio equipment

HDMI

RGB OUT

VIDEO/Y

Pr/Cr

AUDIO IN

AUDIO OUT

Pb/Cb

S-VIDEO

RGB IN 2

RGB IN 1

RS-232C

MONO

Cables used for connection ( *Cables are not supplied with the projector.) Audio cable*

External Audio Equipment

Audio input

(R) (L)

Installation

Audio cable (Stereo)

Audio output (Stereo)

Audio output

(R) (L)

AUDIO IN

Audio cable (Stereo)

Audio cable

Note: The left and right channels are combined when there is only the L (mono) is inserted.

Unplug the power cords of both the projector and external equipment from the AC outlet before connecting the cables.

Installation

Connecting to the AC power cord

This projector uses nominal input voltages of 100240 V AC and it automatically selects the correct input voltage. It is designed to work with a singlephase power system having a grounded neutral conductor. To reduce the risk of electrical shock, do not plug into any other type of power system. If you are not sure of the type of power being

supplied, consult your authorized dealer or service

center. Connect the projector with all peripheral equipment before turning it on.

The AC outlet should be near this equipment and must be easily accessible.

√ Note: Unplug the AC power cord when the projector is not in use. When the projector is connected to an outlet with AC power cord, it is in stand-by mode and consumes a little electric power.

Note on the power cord

AC power cord must meet the requirements of the country where you use the projector. Conrm the AC

plug type with the chart below and proper AC power cord must be used.

Projector side

For the U.S.A. and

Canada

Ground

Connect the AC power cord (supplied) to the projector.

AC outlet side

For Continental

Europe

For the U.K.

Ground

To power cord connector on your projector.

√ Note:

● Using incorrect power cord may inuence the product performance, or even cause hazards like an electric shock or re. To ensure the product performance and security, please apply the cable of the same model with the original one.

● Common connecting cables include the AC power cord, various RGB cables, video cable,and serial control cable.

To the AC outlet. (110 V AC)

To the AC outlet. (200 - 240 V AC)

+ 51 hidden pages