LG ARNU093TUD4 INSTALLATION MANUAL

http://www.lghvac.com

www.lg.com

INSTALLATION MANUAL

AIR CONDITIONER

Ceiling Cassette - 1Way

Please read this installation manual completely before installing the product. Installation work must be performed in accordance with the national wiring standards by authorized personnel only. Please retain this installation manual for future reference after reading it thoroughly.

P/NO : MFL68686505 Rev.03_040318

ENGLISH FRANÇAIS

ESPAÑOL

2 Indoor Unit

IMPORTANT!

Please read this instruction sheet completely before installing the product.

This air conditioning system meets strict safety and operating standards. As the installer or service person, it is an important part of your job to install or service the system so it operates safely and efficiently.

Caution: Improper installation, adjustment, alteration, service or maintenance can void the warranty.The

weight of the condensing unit requires caution and proper handling procedures when lifting or moving to avoid personal injury. Use care to avoid contact with sharp or pointed edges.

Safety Precautions

• Always wear safety eye wear and work gloves when installing equipment.

• Never assume electrical power is disconnected. Check with meter and equipment.

• Keep hands out of fan areas when power is connected to equipment.

• R-410A causes frostbite burns.

• R-410A is toxic when burned.

Note to installing dealer: The Owners Instructions and Warranty are to be given to the owner or prominently displayed near the indoor Furnace/Air Handler Unit.

When wiring: Electrical shock can cause severe personal injury or death. Only a qualified, experienced electrician should attempt to wire this system.

• Do not supply power to the unit until all wiring and tubing are completed or reconnected and checked.

• Highly dangerous electrical voltages are used in this system. Carefully refer to the wiring diagram and these instructions when wiring. Improper connections and inadequate grounding can cause accidental injury or death.

• Ground the unit following local electrical codes.

• Connect all wiring tightly. Loose wiring may cause overheating at connection points and a possible fire hazard.

When transporting:

Be careful when picking up and moving the indoor and outdoor units. Get a partner to help, and bend your knees when lifting to reduce strain on your back. Sharp edges or thin aluminum fins on the air conditioner can cut your finger.

When installing... ... in a wall: Make sure the wall is strong enough to hold the unit's weight. It may be necessary to construct a

strong wood or metal frame to provide added support.

... in a room: Properly insulate any tubing run inside a room to prevent "sweating" that can cause dripping and

water damage to wall and floors.

... in moist or uneven locatinons: Use a raised concrete pad or concrete blocks provide a solid, level foundation

for the outdoor unit. This prevents water damage and abnormal vibration.

... in an area with high winds: Securely anchor the outdoor unit down with bolts and a metal frame. Provide a

suitable air baffle.

... in a snowy area(for Heat Pump Model): Install the outdoor unit on a raised platform that is higher than drifting

snow. Provide snow vents.

When connecting refrigerant tubing:

• Keep all tubing runs as short as possible.

• Use the flare method for connecting tubing.

• Check carefully for leaks before starting the test run.

When servicing:

• Turn the power OFF at the main power box(mains) before opening the unit to check or repair electrical parts and wiring.

• Keep your fingers and clothing away from any moving parts.

• Clean up the site after you finish, remembering to check that no metal scraps or bits of wiring have been left inside the unit being serviced.

• The information contained in the manual is intended for use by a qualified service technician familiar with safety procedures and equipped with the proper tools and test instruments.

• Failure to carefully read and follow all instructions in this manual can result in equipment malfunction, property damage, personal injury and/or death.

WARNING

Installation Manual 3

4 INSTALLATION PARTS

5 SAFETY PRECAUTIONS

7 INSTALLATION

7 Selection of the best location

8 Ceiling dimension and hanging bolt location

9 Wiring Connection

10 Flaring work

11 Installation of Decoration Panel (Panel Type)

12 Installation of Decoration Panel (Grille Type)

13 Plumbing materials and storage methods

14 Drain Piping

15 DIP Switch Setting

16 Group Control Setting

20 Model Designation

20 Airborne Noise Emission

20 Limiting concentration

TABLE OF CONTENTS

Table of contents

ENGLISH

4 Indoor Unit

Installation Parts

Panel type Grille type

• Screws for fixing panels are attached to decoration panel.

Installation Tool

Outlet

Air Inlet

Outlet

Name

Quantity

Shape

Drain hose

Name

Quantity

Shape

1 EA

Inlet

Wired Remote Controller

Clamp metal

2 EA

Paper pattern for installation

(Accessory)

Washer for

hanging backet

1 EA

8 EA

Inlet

Plastic band

4 EA

Insulation for

fitting

1 SET

for gas pipe

for liquid pipe

Installation and Owner's manual

1 EA

Wired Remote Controller

(Accessory)

Conduit

mounting plate

1 EA

Installation Manual 5

Safety Precautions

ENGLISH

Safety Precautions

To prevent injury to the user or other people and property damage, the following instructions must be followed.

n Be sure to read before installing the air conditioner. n Be sure to observe the cautions specified here as they include important items related to safety. n Incorrect operation due to ignoring instruction will cause harm or damage. The seriousness is classified by the

following indications.

n Meanings of symbols used in this manual are as shown below.

This symbol indicates the possibility of death or serious injury.

This symbol indicates the possibility of injury or damage to properties only.

Be sure not to do.

Be sure to follow the instruction.

WARNING

Installation

• Do not use a defective or underrated circuit breaker. Use this appliance on a dedicated circuit.