OWNER’S MANUAL
Safety and Reference
LG Digital Signage
(MONITOR SIGNAGE)
Please read this manual carefully before operating your set and retain it for future reference.
www.lg.com
Copyright © 2018 LG Electronics Inc. All Rights Reserved.
<![endif]>ENGLISH
Warning! Safety Instructions
CAUTION
RISKOFELECTRICSHOCK
DONOTOPEN
CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER-SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.
This symbol is intended to alert the user to the presence of uninsulated “dangerous voltage” within the product’s
enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
This symbol is intended to alert the user to the presence of important operating and maintenance (servicing)
instructions in the literature accompanying the appliance.
WARNING : TO REDUCE THE RISK OF FIRE AND ELECTRIC SHOCK, DO NOT EXPOSE THIS PRODUCT TO RAIN OR MOISTURE.
•• TO PREVENT THE SPREAD OF FIRE, KEEP CANDLES OR OTHER ITEMS WITH OPEN FLAMES AWAY FROM THIS PRODUCT AT ALL TIMES.
•• Do not place the monitor and/or remote control in the following environments:
-- Keep the product away from direct sunlight.
-- An area with high humidity such as a bathroom.
-- Near any heat source such as stoves and other devices that produce heat.
-- Near kitchen counters or humidifiers where they can easily be exposed to steam or oil.
-- An area exposed to rain or wind.
-- Do not expose to dripping or splashing and do not place objects filled with liquids, such as vases, cups, etc. on or over the apparatus (e.g., on shelves above the unit).
-- Near flammable objects such as gasoline or candles, or expose the monitor to direct air conditioning.
-- Do not install in excessively dusty places.
Otherwise, this may result in fire, electric shock, combustion/ explosion, malfunction or product deformation.
•• Ventilation
-- Install your monitor where there is proper ventilation. Do not install in a confined space such as a bookcase.
-- Do not install the product on a carpet or cushion.
-- Do not block or cover the product with cloth or other materials while unit is plugged in.
•• Take care not to touch the ventilation openings. When watching the monitor for a long period, the ventilation openings may become hot.
•• Protect the power cord from physical or mechanical abuse, such as being twisted, kinked, pinched, closed in a door, or walked upon. Pay particular attention to plugs, wall outlets, and the point where the cord exits the device.
•• Do not move the monitor whilst the Power cord is plugged in.
•• Do not use a damaged or loosely fitting power cord.
•• Be sure to grasp the plug when unplugging the power cord. Do not pull on the power cord to unplug the monitor.
•• Do not connect too many devices to the same AC power outlet as this could result in fire or electric shock.
•• Disconnecting the Device from the Main Power
-- The power plug is the disconnecting device. In case of an emergency, the power plug must remain readily accessible.
•• Do not let your children climb or cling onto the monitor. Otherwise, the monitor may fall over, which may cause serious injury.
2
•• Make sure the power cord is connected securely to the monitor and wall socket if not secured damage to the Plug and socket may occur and in extreme cases a fire may break out.
•• Do not insert metallic or inflammable objects into the product. If a foreign object is dropped into the product, unplug the power cord and contact the customer service.
•• Do not touch the end of the power cord while it is plugged in. You may be electrocuted.
•• If any of the following occur, unplug the product immediately and contact your local customer service.
-- The product has been damaged.
-- If water or another substance enters the product (like an AC adapter, power cord, or monitor).
-- If you smell smoke or other odors coming from the monitor.
-- When lightning storms or when unused for long periods of time.
Even the monitor is turned off by remote control or button, AC power source is connected to the unit if not unplugged in.
•• Do not use high voltage electrical equipment near the monitor (e.g., a bug zapper). This may result in product malfunction.
•• Do not attempt to modify this product in any way without written authorization from LG Electronics. Accidental fire or electric shock can occur. Contact your local customer service for service or repair.
Unauthorized modification could void the user’s authority to operate this product.
•• Use only an authorized attachments / accessories approved by LG Electronics. Otherwise, this may result in fire, electric shock, malfunction, or product damage.
•• Never disassemble the AC adapter or power cord. This may result in fire or electric shock.
•• Handle the adapter carefully to avoid dropping or striking it. An impact could damage the adapter.
•• To reduce the risk of fire or electrical shock, do not touch the monitor with wet hands. If the power cord prongs are wet or covered with dust, dry the power plug completely or wipe dust off.
•• Batteries
-- Store the accessories (battery, etc.) in a safe location out of the reach of children.
-- Do not short circuit, disassemble, or allow the batteries to overheat. Do not dispose of batteries in a fire. Batteries should not be exposed to excessive heat.
•• Moving
-- When moving, make sure the product is turned off, unplugged, and all cables have been removed. It may take 2 or more people to carry larger monitors. Do not press or put stress on the front panel of the monitor. Otherwise, this may result in product damage, fire hazard or injury.
•• Keep the packing anti-moisture material or vinyl packing out of the reach of children.
•• Do not allow an impact shock, any objects to fall into the product, and do not drop anything onto the screen.
•• Do not press strongly upon the panel with a hand or a sharp object such as a nail, pencil, or pen, or make a scratch on it. It may cause damage to screen.
•• Cleaning
-- When cleaning, unplug the power cord and wipe gently with a soft/dry cloth. Do not spray water or other liquids directly on the monitor. Do not clean your monitor with chemicals including glass cleaner, any type of air freshener, insecticide, lubricants, wax (car, industrial), abrasive, thinner, benzene, alcohol etc., which can damage the product and/or its panel. Otherwise, this may result in electric shock or product damage.
<![endif]>ENGLISH
3
<![endif]>ENGLISH
Preparing
•• If the monitor is turned on for the first time after it was shipped from the factory, initialization of the monitor may take a few minutes.
•• Image shown may differ from your monitor.
•• Your monitor’s OSD (On Screen Display) may differ slightly from that shown in this manual.
•• The available menus and options may differ from the input source or product model that you are using.
•• New features may be added to this monitor in the future.
•• The device must be easily accessed to a location outlet near the access. Some devices are not made by turning on / off button, turning off the device and unplugging the power cord.
•• The items supplied with your product may vary depending on the model.
•• Product specifications or contents of this manual may be changed without prior notice due to upgrade of product functions.
•• For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick and 18 mm width. Use an extension cable that supports USBif the USB cable or USB memory stick does not fit into your monitor’s USB port.
B |
B |
* A < |
10 mm |
|
|
= |
|
A |
A |
* B =< 18 mm |
•• Use a certified cable with the HDMI logo attached.
•• If you do not use a certified HDMI cable, the screen may not display or a connection error may occur. (Recommended HDMI Cable Types)
-- High-Speed HDMI®/TM Cable (3 m or less)
-- High-Speed HDMI®/TM Cable with Ethernet (3 m or less)
•• SuperSign Software & Manual
-- Downloading from the LG Electronics website.
-- Visit the LG Electronics website (http://partner.lge.com) and download the latest software for your model.
Wall Mounting Bracket
(Depending on model)
Make sure to use screws and wall mount bracket that meet the VESA standard. Standard dimensions for the wall mount kits are described in the following table.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Model |
65UL3E |
|
75UL3E |
|||
|
86UL3E |
|||||
|
|
|
|
|
|
|
VESA (A x B) (mm) |
300 x 300 |
|
600 x 400 |
|||
Standard screw |
M6 |
|
M8 |
|||
Number of screws |
4 |
|
|
|
|
4 |
Wall mount bracket |
OLW480B |
|
LSW640B |
4
Lifting and moving the monitor
Please note the following advice to prevent the monitor from being scratched or damaged and for safe transportation regardless of its type and size.
•• It is recommended to move the monitor in the box or packing material that the monitor originally came in.
•• Before moving or lifting the monitor, disconnect the power cord and all cables.
•• When holding the monitor, the screen should face away from you to avoid damage.
•• Hold the top and bottom of the monitor frame firmly. Make sure not to hold the transparent part, speaker, or speaker grill area.
•• When transporting a large monitor, there should be at least 2 people.
•• When transporting the monitor by hand, hold the monitor as shown in the following illustration.
•• When transporting the monitor, do not expose the monitor to jolts or excessive vibration.
•• When transporting the monitor, keep the monitor upright, never turn the monitor on its side or tilt towards the left or right.
•• Do not apply excessive pressure to cause flexing / bending of frame chassis as it may damage screen.
•• When handling the monitor, be careful not to damage the protruding buttons.
•• Avoid touching the screen at all times, as this may result in damage to the screen.
•• Do not move the monitor by holding the cable holders, as the cable holders may break, and injuries and damage to the monitor may occur.
•• When attaching the stand to the monitor set, place the screen facing down on a cushioned table or flat surface to protect the screen from scratches.
<![endif]>ENGLISH
5
<![endif]>ENGLISH
Mounting on a Table
1Lift and tilt the monitor into its upright position on a table.
•Leave a 10 cm (minimum) space from the wall for proper ventilation.
Using the Kensington security system
The Kensington security system connector is located at the rear of the monitor. For more information of installation and using, refer to the manual provided with the Kensington security system or
visit http://www.kensington.com. Connect the Kensington security system cable between the monitor and a table.
10 cm
|
cm |
|
10 cm |
10 |
|
10 cm |
||
|
||
|
10 cm |
(Depending on model) |
(Depending on model) |
|
|
2 Connect the power cord to a wall outlet. |
|
•• Do not apply foreign substances (oils, lubricants, etc.) to the |
|
screw parts when assembling the product. |
|
(Doing so may damage the product.) |
|
•• If you install the monitor on a stand, you need to take actions |
|
to prevent the product from overturning. Otherwise, the |
|
product may fall over, which may cause injury. |
|
•• Do not use any unapproved items to ensure the safety and |
|
product life span. |
|
•• Any damage or injuries caused by using unapproved items |
|
are not covered by the manufacturer’s warranty. |
|
•• Make sure that the screws are inserted correctly and fastened |
|
securely. (If they are not fastened securely enough, the |
|
monitor may tilt forward after being installed.) Do not use |
|
too much force and over tighten the screws; otherwise screw |
|
may be damaged and not tighten correctly. |
|
6
Mounting to the Wall
Attach an optional wall mount bracket at the rear of the monitor carefully and install the wall mount bracket on a solid wall perpendicular to the floor. When you attach the monitor to other building materials, please contact qualified personnel. LG recommends that wall mounting be performed by a qualified professional installer. We recommend the use of LG’s wall mount bracket. LG’s wall mount bracket is easy to move with cables connected. When you do not use LG’s wall mount bracket, please use a wall mount bracket where the device is adequately secured to the wall with enough space to allow connectivity to external devices. It is advised to connect all the cables before installing fixed wall mounts.
|
10 cm |
|
|
cm |
|
10 cm |
10 |
|
10 cm |
||
|
||
|
10 cm |
(Depending on model)
•• Remove the stand before installing the monitor on a wall mount by performing the stand attachment in reverse.
•• For more information of screws and wall mount bracket, refer to the Separate purchase.
•• If you intend to mount the product to a wall, attach VESA standard mounting interface (optional parts) to the back of the product. When you install the set to use the wall mounting bracket (optional parts), fix it carefully so as not to drop.
•• When mounting a monitor on the wall, make sure not to install the monitor by hanging the power and signal cables on the back of the monitor.
•• Do not install this product on a wall if it could be exposed to oil or oil mist. This may damage the product and cause it to fall.
•• When installing the wall mounting bracket, it is recommended to cover the stand hole using tape, in order to prevent the influx of dust and insects. (Depending on model)
<![if ! IE]> <![endif]>ENGLISH |
Stand hole |
•• This model does not support rotating installation of the monitor except the default installation.
<![if ! IE]> <![endif]>A |
A |
<![if ! IE]> <![endif]>A |
|
||
|
A |
|
7
<![endif]>ENGLISH
Connections
Connect various external devices to the monitor and switch input modes to select an external device. For more information of external device’s connection, refer to the manual provided with each device.
Other connections
Connect your monitor to external devices. For the best picture and audio quality, connect the external device and the monitor with the HDMI cable. Some separate cable is not provided.
HDMI
•• Supported HDMI Audio format (Depending on model): DTS (44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz),
DTS HD (44.1 kHz / 48 kHz / 88.2 kHz / 96 kHz / 176.4 kHz / 192 kHz), True HD (48 kHz),
Dolby Digital / Dolby Digital Plus (32 kHz / 44.1 kHz / 48 kHz), PCM (32 kHz / 44.1 kHz / 48 kHz / 96 kHz / 192 kHz)
(Only UHD models)
•• (SETTINGS)
(
)
[Picture]
[Additional
Settings][HDMI ULTRA HD Deep Colour]
-- On : Support 4K @ 50/60 Hz (4:4:4, 4:2:2, 4:2:0) -- Off : Support 4K @ 50/60 Hz 8 bit (4:2:0)
If the device connected to Input Port also supports ULTRA HD Deep Colour, your picture may be clearer. However, if the device doesn’t support it, it may not work properly. In that case, change the monitor’s [HDMI ULTRA HD Deep Colour] setting to [Off].
USB
Some USB Hubs may not work. If a USB device connected through a USB Hub is not detected, connect it directly to the USB port on the monitor.
External Devices
Available external devices are: Blu-ray player, HD receivers, DVD players, VCRs, audio systems, USB storage devices, PC, gaming devices, and other external devices.
•• The external device connection may differ from the model.
•• Connect external devices to the monitor regardless of the order of the monitor port.
•• Refer to the external equipment’s manual for operating instructions.
•• If you connect a gaming device to the monitor, use the cable supplied with the gaming device.
•• If ULTRA HD content is played on your PC, video or audio may become disrupted intermittently depending on your PC’s performance. (Depending on model)
•• When connecting via a wired LAN, it is recommended to use a CAT 7 cable. (Only whenport is provided.)
8
Network
Wired network connection
This monitor can be connected to a Pro:Centric server via the LAN port. After making the physical connection, the monitor needs to be set up for network communication.
Connect the LAN port of the Modem or Router from Pro:Centric server to the LAN port on the monitor.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Router |
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Broadband Modem |
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|||||||||||||
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Pro:Centric Server (Depending on model)
Broadband Modem
Pro:Centric Server (Depending on model)
1Connect the LAN port of the Modem or Router to the LAN port on the monitor.
2Connect the LAN port of the PC to the AUX LAN port on the monitor. (Depending on model)
•• Do not connect a modular phone cable to the LAN port.
•• Since there are various connection methods, please follow the specifications of your telecommunication carrier or internet service provider.
Using Button
You can simply operate the monitor functions, using the button.
Basic functions
Power On (Press the button When the monitor is turned off.)
Power Off1 (Press and Hold the button When the monitor is turned on.)
Menu Control (Press the button When the monitor is turned on.2)
Menu Selection (Press and Hold the button when you access menu control.3)
1All running apps will close.
2You can access and adjust the menu by pressing the button when monitor is on.
3You can use the function when you access menu control.
Adjusting the menu
When the monitor is turned on, press thebutton one time. You can adjust the Menu items using the button.
Turns the power off.
Changes the input source.
Adjusts the volume level.
<![endif]>ENGLISH
9