LG 65LM6200, 42LT760H Owner’s Manual

OWNER’S MANUAL

LED LCD TV

Please read this manual carefully before operating your set and retain it for future reference.

LT64** LT65**

LT76** LS34** LS64**

www.lg.com

ENGLISH

TABLE OF CONTENTS

3 LICENSES

3 OPEN SOURCE SOFTWARE

4 INSTALLATION PROCEDURE

4 ASSEMBLING AND

4 Unpacking 8 Separate purchase 9 Parts and buttons 11 Lifting and moving the TV 12 Setting up the TV 12 - Attaching the stand 15 Mounting on a table 17 Mounting on a wall 19 Tidying cables

20 MAKING CONNECTIONS

20 Adapter connection 20 Antenna connection 21 HDMI connection 22 DVI to HDMI connection 23 Component connection 23 RGB-PC connection 24 Composite connection 24 Audio connection 24 - Digital optical audio connection 25 Speaker output setup 25 - Volume control port 25 External speaker out 26 Network Connection 26 - Connecting to a Wired Network 26 Headphone connection 27 USB connection

28 REMOTE CONTROL

NOTICE

PREPARING

32 MAINTENANCE

32 Cleaning your TV 32 - Screen, frame, cabinet and stand 32 - Power cord

32 TROUBLESHOOTING

33 CAUTION FOR USING

EZSIGN 2.0

34 SPECIFICATIONS

39 IR CODES

40 EXTERNAL CONTROL

DEVICE SETUP

40 RS-232C Setup 40 Type of connector;

D-Sub 9-Pin Male 40 RS-232C Configurations 41 Communication Parameters 41 Command reference list 42 Transmission / Receiving Protocol

WARNING

If you ignore the warning message, you may

be seriously injured or there is a possibility of accident or death.

CAUTION

If you ignore the caution message, you may

be slightly injured or the product may be damaged.

NOTE

The note helps you understand and use

the product safely. Please read the note carefully before using the product.

LICENSES / OPEN SOURCE SOFTWARE NOTICE

LICENSES

Supported licenses may differ by model. For more information about licenses, visit www.lg.com.

Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are trademarks of Dolby Laboratories.

The terms HDMI and HDMI High-Definition Multimedia interface, and the HDMI logo are trademarks or registered trademarks of HDMI Licensing LLC in the United States and other countries.

ABOUT DIVX VIDEO: DivX® is a digital video format created by DivX, LLC, a subsidiary of Rovi Corporation. This is an official DivX Certified® device that plays DivX video. Visit divx.com for more information and software tools to convert your files into DivX video.

ABOUT DIVX VIDEO-ON-DEMAND: This DivX Certified® device must be registered in order to play purchased DivX Video-on-Demand (VOD) movies. To obtain your registration code, locate the DivX VOD section in your device setup menu. Go to vod. divx.com for more information on how to complete your registration.

ENGLISH

ENGENGLISH

“DivX Certified® to play DivX® video up to HD 1080p, including premium content.”

“DivX®, DivX Certified® and associated logos are trademarks of Rovi Corporation or its subsidiaries and are used under license.”

Covered by one or more of the following U.S. patents : 7,295,673; 7,460,668; 7,515,710; 7,519,274

OPEN SOURCE SOFTWARE NOTICE

To obtain the source code under GPL, LGPL, MPL and other open source licenses, that is contained in this product, please visit http://opensource.lge.com. In addition to the source code, all referred license terms, warranty disclaimers and copyright notices are available for download. LG Electronics will also provide open source code to you on CD-ROM for a charge covering the cost of performing such distribution (such as the cost of media, shipping and handling) upon email request to opensource@lge.com. This offer is valid for three (3) years from the date on which you purchased the product.

ENGLISH

ENG

INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING

NOTE

Image shown may differ from your TV.

Your TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.

The available menus and options may differ from the input source or product model that you are

using. New features may be added to this TV in the future.

The TV can be placed in standby mode in order to reduce the power consumption. And the TV should

be turned off if it will not be watched for some time, as this will reduce energy consumption. The energy consumed during use can be significantly reduced if the level of brightness of the picture

is reduced, and this will reduce the overall running cost.

INSTALLATION PROCEDURE

Open the package and make sure all the accessories are included.

Attach the stand to the TV set.

Connect an external device to the TV set.

Make sure the network connection is available. You can use the TV network functions only when the

network connection is made. (Only LT74**, LT76**)

ASSEMBLING AND PREPARING

Unpacking

Check your product box for the following items. If there are any missing accessories, contact the local dealer where you purchased your product. The illustrations in this manual may differ from the actual product and item.

CAUTION

Do not use any unapproved items to ensure the safety and product life span.

Any damages or injuries by using unapproved items are not covered by the manufacturer’s warranty.

Some models have a thin film attached on to the screen and this must not be removed.

NOTE

The items supplied with your product may vary depending on the model.

Product specifications or contents of this manual may be changed without prior notice due to upgrade

of product functions. For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm thick

and 18 mm width. Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV’s USB port.

*A 10 mm

*B 18 mm

ENERGY

SAVING

1 2 3

4 5 6

7 809

LIST

BACK

ASSEMBLING AND PREPARING

ENGLISH

AV MODE

INPUT

FLASHBK

MARK

FAV

P A G

CHVOL

MUTE

INFO

Q.MENU

ENTER

EXIT

L/R SELECT

FREEZE

RATIO

Remote control, Batteries (AAA)

Owner’s manual

(See p.28, 29, 30, 31)

Cable holder

(Depending on model) (See p.19)

Power cord

(Depending on model)

Stand Screws

8 EA, M4 x 14

Stand Screws

8 EA, M4 x 12 (Only 26LT64**, 26LT65**) (See p.12)

(Only 32/37/42/47LT64

32/37/42/47LT65**, 32/37/42/47LT74**,

32/37/42/47LT76**) (See p.13)

**,

ENGENGLISH

Stand Screws

2EA, P4 x 16 4EA, M4 x 20 (Only 32LS34**)

(See p.13)

Stand Screws

8 EA, M4 x 20 (Only 55LS64**) (See p.14)

Wall mount Screws

4 EA, M6 x 51 (Only 47LT**** models)

Power Cord holder

(Only 32/37/42/47LT64**,

32/37/42/47LT65**, 32/37/42/47LT74**,

32/37/42/47LT76**) (See p.19)

Stand Screws

4EA, P4 x 16 4EA, M4 x 14 (Only 42LS34**)

(See p.14)

Desk-mount Screw

1 EA (Only 32/37/42/47LT64**,

32/37/42/47LT65**, 32/37/42/47LT74**,

32/37/42/47LT76**,

32/42LS34**)

(See p.15)

Stand Screws

4EA, M4 x 12 2EA, P4 x 16

(Only 22LT65**) (See p.12)

Protection cover

(Only 32/37/42/47LT64**,

32/37/42/47LT65**, 32/37/42/47LT74**,

32/37/42/47LT76**) (See p.18)

DC Adapter

Protection cover

(Only 32LS34**) (See p.18)

(Only 26LT64**,

22/26LT65**)

(See p.20)

ENGLISH

ENG

ASSEMBLING AND PREPARING

Stand body / Stand base

(Only 26LT64**,

22/26LT65**)

(See p.12)

Stand body / Stand base

(Only 32/37/42/47LT64**,

32/37/42/47LT65**, 32/37/42/47LT74**,

32/37/42/47LT76**) (See p.13)

Stand body / Stand base

(Only 32LS34**)

(See p.13)

Stand body / Stand base

(Only 55LS64**)

(See p.14)

Isolator

(Depending on model) (See p.7)

Stand body / Stand base

(Only 42LS34**)

(See p.14)

EzSign 2.0 Editor CD

(Only LT640E)

Wall mount inner spacers

4EA

(Only 55LS64**)

(See p.18)

ASSEMBLING AND PREPARING

NOTE

Antenna Isolator Installation Guide

- Use this to install TV in a place where there is a voltage difference between TV Set and GND of antenna signal.

»If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact

might be heated and excessive heat might cause an accident.

- You can improve the safety when watching TV by efficiently removing power voltage from TV antenna. It is recommended to mount the isolator to the wall. If it cannot be mounted to the wall, mount it on the TV. Avoid disconnecting the antenna Isolator after installation.

- Before starting, be sure that the TV antenna is connected.

1. Connect to TV.

Wall

ANTENNA/

CABLE IN

ENGLISH

ENGENGLISH

Cable / Antenna

Isolator

2. Connect to Set-Top box.

Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.

“Equipment connected to the protective earthing of the building installation through the mains connection or through other equipment with a connection to protective earthing - and to a cable

distribution system using coaxial cable, may in some circumstances create a re hazard. Connection

to a cable distribution system has therefore to be provided through a device providing electrical isolation below a certain frequency range (galvanic isolator, see EN 60728-11)”

When applying the RF Isolator, a slight loss of signal sensitivity can occur.

ENGLISH

ENG

ASSEMBLING AND PREPARING

CAUTION

Power Cord Installation Guide

- If the power cord provided with TV looks like the below picture, please ensure that it is inserted in the right direction.

Power Cord

Correct

Wrong

Separate purchase

Separate purchase items can be changed or modified for quality improvement without any notification. Contact your dealer to buying these items. These devices only work with certain models.

AN-WF100

Wireless Dongle (Only LT640E)

Compatibility

AN-WF100

Wireless Dongle

LT640E

•

LT640H, LT650H, LT740H,

LT760H, LS345H, LS645H

ASSEMBLING AND PREPARING

Parts and buttons

(Only LT64**, LT65**, LT74**, LT76**)

Buttons

(Only 32/37/42/47LT64**,

32/37/42/47LT65**, 32/37/42/47LT74**,

32/37/42/47LT76**)

Screen

Buttons

(Only 26LT64**,

22/26LT65**)

ENGLISH

ENGENGLISH

Remote control sensor

Power Indicator

(Can be adjusted using

the Power Indicator

in the OPTION -menu.)

Clock LED

(Only LT64**, LT74**)

Button Description

∧∨

+ -

Speakers

Scrolls through the saved programmes.

Adjusts the volume level.

Turns the power on or off.

ENGLISH

INPUT

SETTINGS

INPUT

ENGLISH

ENG

ASSEMBLING AND PREPARING

(A type : Only 32/42LS34**)

Screen

Speakers

Remote control sensor

Power indicator

Button

(B type : Only 55LS64**)

Screen

Speakers

Remote control sensor

Power Indicator (Can be adjusted

using the Power Indicator in the OPTION menu.)

SETTINGS INPUT

Touch buttton

A type B type

Button Touch button

∧∨ ∨∧

+ - - +

S SETTINGS

INPUT

/ I

Scrolls through the saved programmes.

Adjusts the volume level.

Selects the highlighted menu option or confirms an input.

Accesses the main menu, or saves your input and exits the menus.

Changes the input source.

Turns the power on or off.

Description

1 B type buttons are touch sensitive and can be operated through simple touch with your nger.

ASSEMBLING AND PREPARING

Lifting and moving the TV

When moving or lifting the TV, read the following to prevent the TV from being scratched or damaged and for safe transportation regardless of its type and size.

CAUTION

Avoid touching the screen at all times, as this

may result in damage to the screen.

It is recommended to move the TV in the box

or packing material that the TV originally came in. Before moving or lifting the TV, disconnect the

power cord and all cables. When holding the TV, the screen should face

away from you to avoid damage.

When transporting a large TV, there should be

at least 2 people. When transporting the TV by hand, hold the TV

as shown in the following illustration.

When transporting the TV, do not expose the

TV to jolts or excessive vibration. When transporting the TV, keep the TV upright,

never turn the TV on its side or tilt towards the left or right. Do not apply excessive pressure to cause

exing / bending of frame chassis as it may

damage screen.

ENGLISH

ENGENGLISH

Hold the top and bottom of the TV frame rmly.

Make sure not to hold the transparent part, speaker, or speaker grill area.

ASSEMBLING AND PREPARING

M4X20

ENGLISH

ENG

Setting up the TV

Put your TV on a pedestal stand and mount the TV on a table or wall.

Attaching the stand

(Only 26LT64**, 22/26LT65**)

Stand Body

Stand Base

M4 x 12

4 EA

Front

Top View

P4 x 16

2 EA

(Only 22LT65**)

M4 x 12

(Only 26LT64**, 26LT65**)

4 EA

ASSEMBLING AND PREPARING

M4X20

(Only 32/37/42/47LT64**, 32/37/42/47LT65**,

32/37/42/47LT74**, 32/37/42/47LT76**)

M4 x 14

Stand Body

Front

Stand Base

Top View

4 EA

(Only 32LS34**)

ENGLISH

ENGENGLISH

P4 x 16

2EA

Stand Body

Stand Base

Top View

M4 x 14

4 EA

M4 x 20

4EA

ENGLISH

ENG

ASSEMBLING AND PREPARING

(Only 42LS34**)

(Only 55LS64**)

Stand Body

Stand Base

P4 x 16

4EA

Top View

M4 x 20

4EA

Stand Base

Stand Body

Front

Top View

M4 x 14

4EA

M4 x 20

4EA

ASSEMBLING AND PREPARING

CAUTION

When attaching the stand to the TV

set, place the screen facing down on a

cushioned table or at surface to protect the

screen from scratches. Make sure that the screws are inserted

correctly and fastened securely. If they are not fastened securely enough, the TV may tilt forward after being installed. Do not use too much force and over tighten the screws; otherwise screw may be damaged and not tighten correctly.

NOTE

Remove the stand before installing the TV

on a wall mount by performing the stand attachment in reverse.

Mounting on a table

Lift and tilt the TV into its upright position on a

table.

- Leave a 10 cm (minimum) space from the wall for proper ventilation.

Attaching the TV to a table

Image shown may differ from your TV. The TV must be attached to desk so it cannot be

pulled in a forward/backward direction, potentially causing injury or damaging the product.

(Only 32/37/42/47LT64**, 32/37/42/47LT65**,

32/37/42/47LT74**, 32/37/42/47LT76**)

4-Screws (not provided as parts of the product)

Stand

Table

Screws: M5 x L (*L: Table depth + 8-10 mm) ex) Table depth: 15 mm, Screw: M5 x 25

ENGLISH

ENGENGLISH

10 cm

Connect the power cord to a wall outlet.

CAUTION

Do not place the TV near or on sources of

heat, as this may result in re or other damage.

10 cm

Securing the TV to a table

(Only 32/37/42/47LT64**, 32/37/42/47LT65**,

32/37/42/47LT74**, 32/37/42/47LT76**, 32/42LS34**)

Fix the TV to a table to prevent from tilting forward, damage, and potential injury. Mount the TV on a table, and then insert and tighten the supplied screw on the rear of the stand.

WARNING

To prevent TV from falling over, the TV

should be securely attached to the floor/ wall per installation instructions. Tipping, shaking, or rocking the TV may cause injury.

+ 32 hidden pages