LG 60PN6500-TC Owner's Manual
OWNER’S MANUAL
PLASMA TV
Please read this manual carefully before operating
your set and retain it for future reference.
PN45**
PN65**
P/NO : MFL67648604 (1304-REV01)
Printed in Korea
www.lg.com
2
TABLE OF CONTENTS
ENGLISH
ENG
TABLE OF CONTENTS
3 SAFETy INSTRUCTIONS
8 INSTALLATION PROCEdURE
8 ASSEMBLING ANd PREPARING
8 Unpacking
12 Separate purchase
13 Parts and buttons
14 Lifting and moving the TV
15 Setting up the TV
15 - Attaching the stand
16 - Detaching the stand
17 Mounting on a table
18 Mounting on a wall
19 Tidying cables
20 MAKING CONNECTIONS
20 Antenna Connection
21 HDMI Connection
21 DVI to HDMI connection
22 Component Connection
22 Audio Connection
22 - Digital optical audio connection
23 Composite Connection
24 USB Connection
32 LICENSES
32 OPEN SOURCE SOFTWARE NOTICE
32 ExTERNAL CONTROL dEvICE
SETUP
25 REMOTE CONTROL
27 USING THE USER GUIdE
28 MAINTENANCE
28 Cleaning your TV
28 - Screen, frame, cabinet and stand
28 - Power cord
28 TROUBLESHOOTING
29 SPECIFICATIONS
WARNING
yIf you ignore the warning message, you may
be seriously injured or there is a possibility of
accident or death.
CAUTION
yIf you ignore the caution message, you may be
slightly injured or the product may be damaged.
NOTE
yThe note helps you understand and use the
product safely. Please read the note carefully
before using the product.
SAFETY INSTRUCTIONS
3
SAFETY INSTRUCTIONS
Please read these safety precautions carefully before using the product.
WARNING
Do not place the TV and/or
y
remote control in the following
environments:
- A location exposed to
direct sunlight
- An area with high humidity
such as a bathroom
- Near any heat source
such as stoves and other
devices that produce heat
- Near kitchen counters or
humidifiers where they can
easily be exposed to steam
or oil
- An area exposed to rain or
wind
- Near containers of water
such as vases
Otherwise, this may result in
fire, electric shock, malfunction
or product deformation.
Do not place the product
y
where it might be exposed to
dust.
This may cause a fire hazard.
Mains Plug is the TV
y
connecting/disconnecting
device to AC mains electric
supply.
This plug must remain readily
attached and operable when
TV is in use.
Do not touch the power plug
y
with wet hands. Additionally, if
the cord pin is wet or covered
with dust, dry the power plug
completely or wipe dust off.
You may be electrocuted due
to excess moisture.
Make sure to connect Mains
y
cable to compliant AC mains
socket with Grounded earth
pin. (Except for devices
which are not grounded on
earth.) Otherwise possibility
you may be electrocuted or
injured.
Insert power cable plug
y
completely into wall socket
otherwise if not secured
completely into socket, fire
ignition may break out.
Ensure the power cord does
y
not come into contact with
hot objects such as a heater.
This may cause a fire or an
electric shock hazard.
Do not place a heavy object,
y
or the product itself, on power
cables.
Otherwise, this may result in
fire or electric shock.
Bend antenna cable between
y
inside and outside building to
prevent rain from flowing in.
This may cause water
damaged inside the Product
and could give an electric
shock.
When mounting TV onto wall
y
make sure to neatly install
and isolate cabling from
rear of TV as to not create
possibility of electric shock /
fire hazard.
Do not plug too many
y
electrical devices into a single
multiple electrical outlet.
Otherwise, this may result in
fire due to over-heating.
Do not drop the product or let
y
it fall over when connecting
external devices.
Otherwise, this may result
in injury or damage to the
product.
ENGENGLISH
4
SAFETY INSTRUCTIONS
ENGLISH
ENG
Keep the anti-moisture
y
packing material or vinyl
packing out of the reach of
children.
Anti-moisture material is
harmful if swallowed. If
swallowed by mistake, force
the patient to vomit and
visit the nearest hospital.
Additionally, vinyl packing can
cause suffocation. Keep it out
of the reach of children.
Do not let your children climb
y
or cling onto the TV.
Otherwise, the TV may
fall over, which may cause
serious injury.
Dispose of used batteries
y
carefully to ensure that a
small child does not consume
them.
Please seek Doctor- Medical
Attention immediately if child
consumes batteries.
Do not insert any metal
y
objects/conductors (like
a metal chopstick/cutlery/
screwdriver) between power
cable plug and input Wall
Socket while it is connected
to the input terminal on the
wall. Additionally, do not
touch the power cable right
after plugging into the wall
input terminal.
You may be electrocuted.
(Depending on model)
Do not put or store
y
inflammable substances
near the product. There is
a danger of combustion/
explosion or fire due to
careless handling of the
inflammable substances.
Do not drop metallic objects
y
such as coins, hair pins,
chopsticks or wire into the
product, or inflammable
objects such as paper and
matches. Children must pay
particular attention.
Electrical shock, fire or injury
can occur. If a foreign object
is dropped into the product,
unplug the power cord and
contact the service centre.
Do not spray water on the
y
product or scrub with an
inflammable substance
(thinner or benzene). Fire or
electric shock accident can
occur.
Do not allow any impact,
y
shock or any objects to fall
into the unit, and do not drop
anything onto the screen.
You may be injured or the
product can be damaged.
Never touch this product or
y
antenna during a thunder or
lighting storm.
You may be electrocuted.
Never touch the wall outlet
y
when there is leakage of
gas, open the windows and
ventilate.
It may cause a fire or a burn
by a spark.
Do not disassemble, repair
y
or modify the product at your
own discretion.
Fire or electric shock accident
can occur.
Contact the service centre for
check, calibration or repair.
If any of the following
y
occur, unplug the product
immediately and contact your
local service centre.
- The product has been
impacted by shock
- The product has been
damaged
- Foreign objects have
entered the product
- The product produced
smoke or a strange smell
This may result in fire or
electric shock.
SAFETY INSTRUCTIONS
5
Unplug the TV from AC
y
mains wall socket if you do
not intend to use the TV
for a long period of time.
Accumulated dust can cause
fire hazard and insulation
deterioration can cause
electric leakage/shock/fire.
Apparatus shall not be
y
exposed to dripping or
splashing and no objects
filled with liquids, such as
vases, shall be placed on the
apparatus.
CAUTION
Install the product where no
y
radio wave occurs.
There should be enough
y
distance between an outside
antenna and power lines
to keep the former from
touching the latter even when
the antenna falls.
This may cause an electric
shock.
Do not install the product
y
on places such as unstable
shelves or inclined surfaces.
Also avoid places where
there is vibration or where
the product cannot be fully
supported.
Otherwise, the product may
fall or flip over, which may
cause injury or damage to the
product.
If you install the TV on a
y
stand, you need to take
actions to prevent the product
from overturning. Otherwise,
the product may fall over,
which may cause injury.
If you intend to mount the product to a wall, attach
y
VESA standard mounting interface (optional parts)
to the back of the product. When you install the set
to use the wall mounting bracket (optional parts),
fix it carefully so as not to drop.
Only use the attachments / accessories specified
y
by the manufacturer.
When installing the antenna,
y
consult with a qualified
service technician. If not
installed by a qualified
technician, this may create
a fire hazard or an electric
shock hazard.
We recommend that you
y
maintain a distance of at least
2 to 7 times the diagonal
screen size when watching
TV.
If you watch TV for a long
period of time, this may
cause blurred vision.
Only use the specified type of
y
battery.
This could cause damage to
the remote control.
Do not mix new batteries with
y
old batteries.
This may cause the batteries
to overheat and leak.
Batteries should not be exposed to excessive heat.
y
For example, keep away from direct Sunlight, open
fireplace and electric heaters.
Do not place non-rechargeable batteries in
y
charging device.
Make sure there are no
y
objects between the remote
control and its sensor.
Signal from Remote Control
y
can be interrupted due to
external/internal lighting eg
Sunlight, fluorescent lighting.
If this occurs turn off lighting
or darken viewing area.
When connecting external
y
devices such as video game
consoles, make sure the
connecting cables are long
enough.
Otherwise, the product may
fall over, which may cause
injury or damage the product.
Do not turn the product
y
On/Off by plugging-in or
unplugging the power plug to
the wall outlet. (Do not use
the power plug for switch.)
It may cause mechanical
failure or could give an
electric shock.
ENGENGLISH
6
SAFETY INSTRUCTIONS
ENGLISH
ENG
Please follow the installation
y
instructions below to prevent
the product from overheating.
- The distance between the
product and the wall should
be more than 10 cm.
- Do not install the product in
a place with no ventilation
(e.g., on a bookshelf or in
a cupboard).
- Do not install the product
on a carpet or cushion.
- Make sure the air vent is
not blocked by a tablecloth
or curtain.
Otherwise, this may result in
fire.
Take care not to touch the
y
ventilation openings when
watching the TV for long
periods as the ventilation
openings may become hot.
This does not affect the
operation or performance of
the product.
Periodically examine the cord of your appliance,
y
and if its appearance indicates damage or
deterioration, unplug it, discontinue use of the
appliance, and have the cord replaced with an
exact replacement part by an authorized servicer.
Prevent dust collecting on the
y
power plug pins or outlet.
This may cause a fire hazard.
Protect the power cord from
y
physical or mechanical
abuse, such as being twisted,
kinked, pinched, closed in a
door, or walked upon. Pay
particular attention to plugs,
wall outlets, and the point
where the cord exits the
appliance.
Do not press strongly upon
y
the panel with a hand or
sharp object such as nail,
pencil or pen, or make a
scratch on it, as it may cause
damage to screen.
Avoid touching the screen or
y
holding your finger(s) against
it for long periods of time.
Doing so may produce some
temporary or permanent
distortion/damage to screen.
When cleaning the product
y
and its components, unplug
the power first and wipe it
with a soft cloth. Applying
excessive force may cause
scratches or discolouration.
Do not spray with water or
wipe with a wet cloth. Never
use glass cleaner, car or
industrial shiner, abrasives
or wax, benzene, alcohol
etc., which can damage the
product and its panel.
Otherwise, this may result in
fire, electric shock or product
damage (deformation,
corrosion or breakage).
As long as this unit is connected to the AC wall
y
outlet, it is not disconnected from the AC power
source even if you turn off this unit by SWITCH.
When unplugging the cable,
y
grab the plug and unplug it,
by pulling at the plug.
Don’t pull at the cord to
unplug the power cord from
the power board, as this
could be hazardous.
When moving the product,
y
make sure you turn the power
off first. Then, unplug the
power cables, antenna cables
and all connecting cables.
The TV set or power cord
may be damaged, which may
create a fire hazard or cause
electric shock.
When moving or unpacking
y
the product, work in pairs
because the product is heavy.
Otherwise, this may result in
injury.
Contact the service centre
y
once a year to clean the
internal parts of the product.
Accumulated dust can cause
mechanical failure.
Refer all servicing to
y
qualified service personnel.
Servicing is required when
the apparatus has been
damaged in any way, such
as power supply cord or
plug is damaged, liquid has
been spilled or objects have
fallen into the apparatus, the
apparatus has been exposed
to rain or moisture, does not
operate normally, or has been
dropped.
If the product feels cold to the
y
touch, there may be a small
“flicker” when it is turned
on. This is normal, there is
nothing wrong with product.
The panel is a high
y
technology display product
with resolution of two million
to six million pixels. You
may see tiny black dots and/
or brightly coloured dots
(red, blue or green) at a
size of 1 ppm on the panel.
This does not indicate a
malfunction and does not
affect the performance and
reliability of the product.
This phenomenon also occurs
in third-party products and is
not subject to exchange or
refund.
You may find different
y
brightness and colour of the
panel depending on your
viewing position(left/right/top/
down).
This phenomenon occurs due
to the characteristic of the
panel. It is not related with
the product performance, and
it is not malfunction.
SAFETY INSTRUCTIONS
Displaying a still image (e.g., broadcasting
y
channel logo, on-screen menu, scene from a
video game) for a prolonged time may cause
damage to the screen, resulting in retention of
the image, which is known as image sticking. The
warranty does not cover the product for image
sticking.
Avoid displaying a fixed image on your
television’s screen for a prolonged period (2
or more hours for LCD, 1 or more hours for
Plasma).
Also, if you watch the TV at a ratio of 4:3 for
a long time, image sticking may occur on the
borders of the panel.
This phenomenon also occurs in third-party
products and is not subject to exchange or
refund.
Generated Sound
y
“Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is generated
by plastic thermal contraction due to temperature and humidity. This noise is common for
products where thermal deformation is required.
Electrical circuit humming/panel buzzing: A
low level noise is generated from a high-speed
switching circuit, which supplies a large amount
of current to operate a product. It varies depending on the product.
This generated sound does not affect the
performance and reliability of the product.
7
ENGENGLISH
8
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
ENGLISH
ENG
NOTE
yImage shown may differ from your TV.
yYour TV’s OSD (On Screen Display) may differ slightly from that shown in this manual.
yThe available menus and options may differ from the input source or product model that you are using.
yNew features may be added to this TV in the future.
yThe TV can be placed in standby mode in order to reduce the power consumption. And the TV should be turned
off if it will not be watched for some time, as this will reduce energy consumption.
yThe energy consumed during use can be significantly reduced if the level of brightness of the picture is reduced,
and this will reduce the overall running cost.
INSTALLATION PROCEDURE
1 Open the package and make sure all the accessories are included.
2 Attach the stand to the TV set.
3 Connect an external device to the TV set.
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you
purchased your product. The illustrations in this manual may differ from the actual product and item.
CAUTION
yDo not use any unapproved items to ensure the safety and product life span.
yAny damag or injuries caused by using unapproved items are not covered by the manufacturer’s warranty.
ySome models have a thin film attached on to the screen and this must not be removed.
Remote control, batteries (AAA)
(See p. 25, 26)
Owner’s manual Ferrite core
(Depending on model)
(See p. 10)
Desk-mount Screw
(Only 42PN45**)
(
See p. 17
)
ASSEMBLING AND PREPARING
9
ENGENGLISH
Power Cord Holder
(Depending on model)
(See p. 19)
Stand Body / Stand
Base
(See p. 15)
Power Cord
(Depending on model)
or
Isolator
(Depending on model)
(See p. 11)
Screw for assembly
7 EA, M4 x 14
(Only 42PN45**)
(See p. 15)
Protection Cover
(Only 50PN45**,50PN65**)
(See p. 16)
Screw for assembly
7 EA, M5 x 16
(Only 50PN45**,
50/60PN65**)
(See p. 15)
10
ASSEMBLING AND PREPARING
ENGLISH
ENG
NOTE
The items supplied with your product may vary depending on the model.
y
Product specifications or contents of this manual may be changed without prior notice due to upgrade of product
y
functions.
How to use the ferrite core
1 Use the ferrite core to reduce the electromagnetic interference in the power cable.
Wind the power cable on the ferrite core once. Place the ferrite core close to the TV and a wall plug.
[to a wall plug]
[Figure 1]
2 Use the ferrite core to reduce the electromagnetic interference in the component Y, Pb, Pr, L,
R cable & AV cable.
Place the ferrite core close to the TV.
Wind the
component Y, Pb, Pr, L, R cable & AV cable
[to an External device]
10 mm(+ / - 5 mm)
[Figure 2-1]
Wind the PC audio cable on the ferrite core once.
[to the TV]
[Cross Section of
Ferrite Core]
on the ferrite core once.
[to the TV]
[Cross Section of
Ferrite Core]
(Black)
(Black)
[to an External device] [to the TV]
10 mm(+ / - 5 mm)
[Figure 2-2]
- If there are two ferrite cores, follow as shown in Figures 1.
- If there are three ferrite cores, follow as shown in Figures 1 and 2.
y For an optimal connection, HDMI cables and USB devices
should have bezels less than 10 mm thick and 18 mm width.
Use an extension cable that supports USB 2.0 if the USB cable or USB memory stick does not fit into your TV’s USB port.
*A 10 mm
*B
18 mm
ASSEMBLING AND PREPARING
NOTE
y Antenna Isolator Installation Guide
- Use this to install TV in a place where there is a voltage difference between TV Set and GND of antenna signal.
» If there is a voltage difference between TV Set and GND of antenna signal, the antenna contact might be
heated and excessive heat might cause an accident.
- You can improve the safety when watching TV by efficiently removing power voltage from TV antenna. It is recom-
mended to mount the isolator to the wall. If it cannot be mounted to the wall, mount it on the TV. Avoid disconnecting the antenna Isolator after installation.
- Before starting, be sure that the TV antenna is connected.
1. Connect to TV.
Wall
ANTENNA/
CABLE IN
or
11
ENGENGLISH
Cable / Antenna
Isolator
2. Connect to Set-Top box.
Connect one end of the isolator to cable/antenna jack and the other to TV set or set-top box.
“Equipment connected to the protective earthing of the building installation through the mains connection or through
other equipment with a connection to protective earthing - and to a cable distribution system using coaxial cable, may
in some circumstances create a re hazard. Connection to a cable distribution system has therefore to be provided
through a device providing electrical isolation below a certain frequency range (galvanic isolator, see EN 60728-11)”
When applying the RF Isolator, a slight loss of signal sensitivity can occur.
12
ASSEMBLING AND PREPARING
ENGLISH
ENG
Separate purchase
Separate purchase items can be changed or modied for quality improvement without any notication.
Contact your dealer to buy these items.
These devices only work with certain models.
LG Audio Device
Compatibility
LG Audio Device • •
The model name or design may be changed depending on the upgrade of product functions,
manufacturer’s circumstances or policies.
PN45** PN65**
ASSEMBLING AND PREPARING
AV IN 2
L/MONO
AV IN 1
LAN
ANTENNA/
CABLE IN
COMPONENT
IN
AUDIO IN (PC)
IN 2
13
Parts and buttons
Buttons
ENGENGLISH
Screen
Speakers
Remote control sensor
Power indicator
Button Description
Turns the power on or off.
Selects the highlighted menu option or confirms an input
S
Accesses the main menus, or saves your input and exits the menus.
Changes the input source
Adjusts the volume level.
Scrolls through the saved programmes.
14
Stand Body
ASSEMBLING AND PREPARING
ENGLISH
ENG
Lifting and moving the TV
Please note the following advice to prevent the TV from
being scratched or damaged and for safe transportation
regardless of its type and size.
CAUTION
yAvoid touching the screen at all times, as this may
result in damage to the screen.
yIt is recommended to move the TV in the box
or packing material that the TV originally came
in.
yBefore moving or lifting the TV, disconnect the
power cord and all cables.
yWhen holding the TV, the screen should face
away from you to avoid damage.
yWhen transporting a large TV, there should be
at least 2 people.
yWhen transporting the TV by hand, hold the
TV as shown in the following illustration.
yWhen transporting the TV, do not expose the
TV to jolts or excessive vibration.
yWhen transporting the TV, keep the TV upright,
never turn the TV on its side or tilt towards the
left or right.
yDo not apply excessive pressure to cause
exing /bending of frame chassis as it may
damage screen.
yHold the top and bottom of the TV frame rmly.
Make sure not to hold the transparent part,
speaker, or speaker grill area.
ASSEMBLING AND PREPARING
15
Setting up the TV
Image shown may differ from your TV.
Attaching the stand
Only 50PN45**, 50/60PN65**
1
Only 42PN45**
Stand Body
3 EA
M5 x 16
3 EA
M4 x 14
Front
ENGENGLISH
3
Only 50PN45**,
50/60PN65**
4 EA
M5 x 16
Only 42PN45**
Stand Base
4 EA
M4 x 14
2
Loading...