LG 58842800 User Manual
Installation Instructions
Pedestal
For washer, dryer, and combo
Kenmore 27”
Instrucciones de la Instalación
Pedestal
Lavadora, secadora y combo
Kenmore de 27”
ENGLISH
ESPAÑOL
2p
6p
IMPORTANT: Read and follow these instructions.
Safety is foremost---both your own and that of other
people. Many important safety instructions are provided
in this instruction and your appliance. Always read and
observe all safety instructions.
1
Remove pedestal, installation hardware, and
instructions from the shipping carton.
2
Position the washer/combo on top of the pedestal.
NOTE:
Because of the weight of the
washer/combo, two or more people
may be needed.
NOTE:
If the washer or combo was previously
installed, unplug it, disconnect the inlet
hose (s) from the faucet (s), disconnect
the drain hose, and drain all hoses.
4
Remove the paper from the
bracket.
5
Attach the double-faced tape of the bracket to the
washer/combo as shown so the bent parts of the
brackets align with the edge and can be attached
to the pedestal with screws.
NOTE:
Attach the lower side first.
6
Be sure to press the adhesive parts of the brackets
firmly to the appliance.
7
Install the eight (8) screws (supplied) to attach the
brackets to the pedestal.
8
Move the washer/combo to the desired place.
NOTE:
The appliance and pedestal assembly
must be placed on a solid and level floor
for proper operation. Adjust the legs of
the appliance and pedestal by turning
with a wrench. Then, adjust the lock nut
toward the pedestal while holding the
pedestal leg using a wrench.
The installer must have electrical and mechanical training and acceptable knowledge in the
required work.
Excessive Weight Hazard
Two or more people may be needed to install and
move the appliance and pedestal assembly.
Do not allow children to play on the drawer.
Do not step on the handle.
NOTICE
W
WASHER/COMBO INSTALLATION
ARNING
for washer/
combo
for dryer
for washer/
combo
for dryer
2
ENGLISH
ESPAÑol
5
Attach the double-faced tape of the bracket to the
washer/combo as shown so the bent parts of the
brackets align with the edge and can be attached
to the pedestal with screws.
NOTE:
Attach the lower side first.
4
Remove the paper from the
bracket.
Level the washer/combo on the pedestal by
adjusting the feet.
Lock
nut
Adjustable
feet
Adjustable
feet
Adjustable
feet
Higher Lower
3
1
Remove pedestal, installation hardware, and
instructions from the shipping carton.
2
Position dryer on top of the pedestal.
NOTE:
Because of the weight of the dryer,
two or more people may be needed.
NOTE:
If dryer was previously installed, uninstall
it as follows:
A. Uninstalling an electric dryer:
1) Unplug the power supply cord,
2) Pull the dryer away from the wall enough to
loosen the vent clamp. Loosen the clamp and
carefully remove the exhaust vent from the
dryer exhaust outlet.
B. Uninstalling a gas dryer:
1) Unplug power supply cord.
2) Turn off the gas supply.
3) Pull the dryer away from the wall enough to
loosen the vent clamp. Loosen the clamp and
carefully remove the exhaust vent from the
dryer exhaust outlet.
3
Remove the paper from the
bracket.
for washer/
combo
for washer/
combo
for dryer
for dryer
DRYER INSTALLATION
for washer/
combo
for dryer
for dryer
for washer/
combo
6
Be sure to press the adhesive parts of the brackets
firmly to the appliance.
7
Install the eight (8) screws (supplied) to attach the
brackets to the pedestal.
8
Move the washer/combo to the desired place.
NOTE:
The appliance and pedestal assembly
must be placed on a solid and level floor
for proper operation. Adjust the legs of
the appliance and pedestal by turning
with a wrench. Then, adjust the lock nut
toward the pedestal while holding the
pedestal leg using a wrench.
Lock
nut
Adjustable
feet
Adjustable
feet
Adjustable
feet
Higher
Lower
ENGLISH
4
ENGLISH
4
Attach the double-faced tape of the bracket to the
dryer as shown so the bent parts of the brackets
align with the edge and can be attached to the
pedestal with screws.
NOTE:
Attach the lower side first.
5
Be sure to press the adhesive parts of the brackets
firmly to the appliance.
6
Install the eight (8) screws(supplied) to attach the
brackets to the pedestal.
7
Move the dryer to the desired place.
NOTE:
The appliance and pedestal assembly
must be placed on a solid and level floor
for proper operation. Adjust the legs of the
appliance and pedestal by turning with a
wrench. Then, adjust the lock unt toward
the pedestal while holding the pedestal leg
using a wrench.
Lock
nut
Adjustable
feet
Adjustable
feet
Adjustable
feet
Higher
Lower
Loading...