LG 52LBX User Manual

Please read this manual carefully before operating
your set.

Retain it for future reference.
Record model number and serial number of the set.
See the label attached on the back cover and quote
this information to your dealer
when you require service.

LCD TV

OWNER’S MANUAL

LCD TV MODELS

42LBX
47LBX
52LBX

www.lgusa.com / www.lg.ca

As an ENERGY STAR
Partner LGE U. S. A.,Inc.
has determined that this
product meets the
ENERGY STAR guidelines
for energy efficiency.

ENERGY STAR is a set of power-saving
guidelines issued by the U.S.
Environmental Protection Agency(EPA).

WARNING / CAUTION

1

WARNING / CAUTION

To prevent fire or shock hazards, do not expose
this product to rain or moisture.

FCC NOTICE

Class B digital device

This equipment has been tested and found to com­ply with the limits for a Class B digital device, pur­suant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio fre­quency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However,
there is no guarantee that interference will not
occur in a particular installation. If this equipment
does cause harmful interference to radio or televi­sion reception, which can be determined by turning
the equipment off and on, the user is encouraged to
try to correct the interference by one or more of
the following measures:

- Reorient or relocate the receiving antenna.

- Increase the separation between the equipment
and receiver.

- Connect the equipment to an outlet on a circuit
different from that to which the receiver is con­nected.

- Consult the dealer or an experienced radio/TV
technician for help.

Any changes or modifications not expressly
approved by the party responsible for compliance
could void the user’s authority to operate the
equipment.

CAUTION

Do not attempt to modify this product in any way
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product

The lightning flash with arrowhead
symbol, within an equilateral triangle,

is intended to alert the user to the
presence of uninsulated “dangerous voltage”
within the product’s enclosure that may be of
sufficient magnitude to constitute a risk of elec­tric shock to persons.

The exclamation point within an equi-

lateral triangle is intended to alert the

user to the presence of important
operating and maintenance (servicing) instruc­tions in the literature accompanying the

appliance.

TO REDUCE THE RISK OF ELECTRIC SHOCK

DO NOT REMOVE COVER (OR BACK). NO

USER SERVICEABLE PARTS INSIDE. REFER TO

QUALIFIED SERVICE PERSONNEL.

WARNING/CAUTION

TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.

NOTE TO CABLE/TV INSTALLER

This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines for
proper grounding and, in particular, specifies that the
cable ground shall be connected to the grounding system
of the building, as close to the point of the cable entry
as practical.

IMPORTANT SAFETY INSTRUCTIONS

SAFETY INSTRUCTIONS

2

Important safety instructions shall be provided with each apparatus. This information shall be given in a separate
booklet or sheet, or be located before any operating instructions in an instruction for installation for use and
supplied with the apparatus.

This information shall be given in a language acceptable to the country where the apparatus is intended to be used.
The important safety instructions shall be entitled “Important Safety Instructions”. The following safety

instructions shall be included where applicable, and, when used, shall be verbatim as follows. Additional safety
information may be included by adding statements after the end of the following safety instruction list. At the
manufacturer’s option, a picture or drawing that illustrates the intent of a specific safety instruction may be
placed immediately adjacent to that safety instruction:

Read these instructions.
Keep these instructions.
Heed all warnings.
Follow all instructions.

Do not use this apparatus near water.

Clean only with dry cloth.

Do not block any ventilation openings. Install in
accordance with the manufacturer’s instructions.

Do not install near any heat sources such as
radiators, heat registers, stoves, or other apparatus
(including amplifiers)that produce heat.

Do not defeat the safety purpose of the polarized
or grounding-type plug. A polarized plug has
two blades with one wider than the other. A
grounding type plug has two blades and a third
grounding prong, The wide blade or the third
prong are provided for your safety. If the provided
plug does not fit into your outlet, consult an
electrician for replacement of the obsolete outlet.

Protect the power cord from being walked on
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from
the apparatus.

Only use attachments/accessories specified by
the manufacturer.

Unplug this apparatus when unused for long
periods of time.

1

2

3

4

5

6

7

8

3

Use only with the cart, stand, tripod, bracket,
or table specified by the manufacturer, or sold
with the apparatus. When a cart is used, use
caution when moving the cart/apparatus
combination to avoid injury from tip-over.

Never touch this apparatus or antenna during
a thunder or lighting storm.

Do not allow a impact shock or any objects to
fall into the product, and do not drop onto the
screen with something.

Refer all servicing to qualified service personnel.
Servicing is required when the apparatus has
been damaged in any way, such as power-supply
cord or plug is damaged, liquid has been
spilled or objects have fallen into the apparatus,
the apparatus has exposed to rain or moisture,
does not operate normally, or has been
dropped.

CAUTION concerning the Power Cord :
Most appliances recommend they be placed
upon a dedicated circuit; that is, a single outlet
circuit which powers only that appliance and
has no additional outlets or branch circuits.
Check the specification page of this owner's
manual to be certain.

Do not overload wall outlets. Overloaded wall
outlets, loose or damaged wall outlets, extension
cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of
these conditions could result in electric shock
or fire. Periodically examine the cord of your
appliance, and if its appearance indicates dam­age or deterioration, unplug it, discontinue use

of the appliance, and have the cord replaced
with an exact replacement part by an authorized
servicer. Protect the power cord from physical
or mechanical abuse, such as being twisted,
kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall
outlets, and the point where the cord exits the
appliance.

Outdoor use marking :
WARNING - To reduce the risk of fire or elec-

tric shock, do not expose this appliance to rain
or moisture.

Wet Location Marking : Apparatus shall not be
exposed to dripping or splashing and no
objects filled with liquids, such as vases, shall
be placed on or over apparatus.

GGRROOUU NNDDIINNGG
Ensure that you connect the earth ground wire

to prevent possible electric shock. If grounding
methods are not possible, have a qualified
electrician install a separate circuit breaker.

Do not try to ground the unit by connecting it
to telephone wires, lightening rods, or gas pipes.

DDIISS CCOONNNNEECC TTIINNGG DDEEVV IICC EE FFRROOMM MMAAII NNSS
Mains plug is the disconnecting device. The

plug must remain readily operable.

9

12

10

11

13

14

15

16

17

Power
Supply

Short-circuit

Breaker

4

CONTENTS

WARNING / CAUTION

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 1

SAFETY INSTRUCTIONS

. . . . . . . . . . . . . . . . . . . . . . . . . . 2

FEATURE OF THIS TV

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6

PREPARATION

Accessories

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7

Front Panel Information

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8

Back Panel Information . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 9

Attaching the TV to a Wall

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 10

Back Cover for Wire Arrangement . . . . . . . . . . . . . . . . . . . . . 11

Desktop Pedestal Installation

. . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

VESA Wall Mounting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12

Antenna or Cable Connection

. . . . . . . . . . . . . . . . . . . . . . . . . . 13

EXTERNAL EQUIPMENT SETUP

HD Receiver Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 14

DVD Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

17

VCR Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 19

PC Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 21

Other A/V Source Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

USB In Setup . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 26

Audio Out Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 27

WATCHING TV / CHANNEL CONTROL

Remote Contro Functions . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 28

Turning On TV . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Channel Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

Volume Adjustment . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 30

On-Screen Menus Selection

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . 31

Channel Setup

- Auto Scan (Auto Tuning)

. . . . . . . . . . . . . . . . . . . . . . . . . . . 32

- Add / Delete Channel (Manual Tuning)

. . . . . . 33

- Channel Editing . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 34

Input List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 35

SimpLink . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 36

Input Label . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .38

Entry Modes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 39

Photo List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 40

Music List

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 44

PICTURE CONTROL

Picture Size (Aspect Ratio) Control

. . . . . . . . . . . . . . . . . . 46

Preset Picture Settings

- Picture Mode - Preset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 47

- Color Tone - Preset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 48

Manual Picture Adjustment

- Picture Mode - User Mode

. . . . . . . . . . . . . . . . . . . . . . . . 49

- Color Tone - User Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . 50

XD - Picture Improvement Technology

. . . . . . . . . . . . . 51

Advanced - Cinema 3:2 Pulldown Mode

. . . . . . . . . . . 52

Advanced - Black (Darkness) Level

. . . . . . . . . . . . . . . . . . . 53

Advanced - TruM

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 54

TruM Demo

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 55

Picture Reset

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .56

SOUND & LANGUAGE CONTROL

Auto Volume Leveler (Auto Volume)

. . . . . . . . . . . . . . . . . 57

Preset Sound Setting (Sound Mode)

. . . . . . . . . . . . . . . . 58

Sound Setting Adjustment - User Mode

. . . . . . . . . . . 59

Balance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .60

Stereo/SAP Broadcasts Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . 61

TV Speakers On/Off Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 62

Audio Language

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 63

On-Screen Menus Language Selection

. . . . . . . . . . . . . 64

Caption Mode

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 65

- Analog Broadcasting System Captions

. . . . . . . 66

- Digital Broadcasting System Captions

. . . . . . . . 67

- Caption Option

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 68

MEDIAMEDIAMEDIA

HOST HOST HOST

MEDIA

HOST

5

TIME SETTING

Clock Setting

- Auto Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .69

- Manual Clock Setup

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 70

Auto On/Off Timer Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 71

Sleep Time Setting

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

72

Auto Shut-off Setting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

73

PARENTAL CONTROL / RATINGS

Set Password & Lock System

. . . . . . . . . . . . . . . . . . . . . . . . . . . 74

Channel Blocking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 76

Movie & TV Rating

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 77

External Input Blocking

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .80

Key Lock

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .

80

APPENDIX

Troubleshooting . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 81

Maintenance

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 83

Product Specifications

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 84

Programming the Remote Control

. . . . . . . . . . . . . . . . . . . 85

IR Codes

. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .89

External Control Through RS-232C

. . . . . . . . . . . . . . . . . .91

PREPARATION

FEATURES OF THIS TV

6

■ If the TV feels cold to the touch, there may be a small “flicker” when it is turned on. This is normal, there is noth-

ing wrong with TV.

■ Some minute dot defects may be visible on the screen, appearing as tiny red, green, or blue spots. However, they

have no adverse effect on the monitor's performance.

■ Avoid touching the LCD screen or holding your finger(s) against it for long periods of time. Doing so may pro-

duce some temporary distortion effects on the screen.

OOnn DDiissppoo ssaall
a. The fluorescent lamp used in this product contains a small amount of mercury.
b. Do not dispose of this product with general household waste.
c. Disposal of this product must be carried out in accordance to the regulations of your local authority.

is a trademark of SRS Labs, Inc.
TruSurround XT technology is incorporated under
license from SRS Labs, Inc.

LG TV with this logo displays Full HD(high-defini­tion) 1080p native resolution by receiving and pro­cessing a Full HD 1080p signal.

LG TV with this logo can play MP3 music from a
MP3 player, such as iPOD, and JPEG images from a
digital camera through the USB device.

With HDMI CEC support of LG’s audio/video device
connected to the HDMI (high-definition multimedia
interface), LG TV with this logo works easily with one
remote control.

It has three HDMI ports that connect audio and
video devices with one cable and produces the high­est quality digital images and sound.

R

TruSurround XT

Manufactured under license from Dolby Laboratories.
“

Dolby

“and the double-D symbol are trademarks of

Dolby Laboratories.

High-definition television. High-resolution digital
television broadcast and playback system composed
of roughly a million or more pixels, 16:9 aspect-ratio
screens, and AC3 digital audio. A subset of digital
television, HDTV formats include 1080i and 720p
resolutions.

LG's own special digital image generator, consisting
of a full digital image processor, six different main
picture quality factors.

R

TruSurround XT

PREPARATION

ACCESSORIES

7

1.5V

1.5V

Owner’s Manual

Batteries

75ohm Round Cable

Remote Control

Cable Management

Ensure that the following accessories are included with your plasma display. If an accessory is missing, please
contact the dealer where you purchased the product.

User must use shielded signal interface cables (D-sub 15 pin cable) with ferrite cores to maintain standard
compliance for the product.

TV INPUT

STB

BACK

■

Slightly wipe stained spot on the exterior only with the polishing

cloth for the product exterior if there is stain or fingerprint on

surface of the exterior.

■

Do not wipe roughly when removing stain. Please be cautions of

that excessive power may cause scratch or discoloration.

Polishing Cloth

OOppttiioonn EExxttrraass

D-sub 15 pin Cable

Power Cord

CD Manual

LCD TV PLASMA TV

Owner's Manual

http://www.lgusa.com

www.lg.ca

Copyright© 2007 LGE,
All Rights Reserved.

PREPARATION

This feature is not available for all models.

2- TV Bracket Bolts

(Refer to p.10)

2- TV Brackets,
2- Wall Brackets
(Refer to p.10)

Twist Holder

Arrange the wires with the

twist holder.

TV INPUT

STB

MENU

BRIG

H
T +

BRIGHT -

LINK

SIMP

TIMER

RATIO

BACK

APM

M/C EJECT

AUTO DEMO

CC

PREPARATION

FRONT PANEL INFORMATION

PREPARATION

8

CH

VOL

CH

VOL

CHANNEL
(

DD,EE

) Buttons

VOLUME
(

FF,GG

) Buttons

ENTER Button

MENU Button

INPUT Button

POWER Button

Remote Control Sensor

Intelligent Eye

Adjusts picture according to
the surrounding conditions.

Power/Standby Indicator

• Illuminates red in standby mode.

• Illuminates green when the set is switched on.

■

Here shown may be somewhat different from your TV.

■

NOTE: If your product has a protection tape attached, remove the tape.

And then wipe the product with a cloth (If a polishing cloth is included with your product, use it).

CH

VOL

ENTER

MENU

INPUT

/I

PREPARATION

BACK PANEL INFORMATION

9

■

Here shown may be somewhat different from your TV.

S-VIDEO

USB Input port

10

RGBRGB

/DVI /DVI

ANTENNA/ANTENNA/
CABLE INCABLE IN

1

3

2

4

5

9

8

7

6

HDMI/DVI IN

Connect a HDMI signal to 1, 2 or 3.
Or DVI (VIDEO)signal to the 1, 2 or 3 port with a

DVI to HDMI cable.

COMPONENT IN

Connect a component video/audio device to these
jacks.

RGB(PC)
AUDIO (RGB/DVI)

Connect the monitor output from a PC to the
appropriate input port.

RS-232C IN (CONTROL & SERVICE) PORT

Connect to the RS-232C port on a PC.

REMOTE CONTROL PORT

Connect your wired remote control.

AV (Audio/Video) IN 1, 2

Connect audio/video output from an external
device to these jacks.

S-VIDEO

Connect S-Video out from an S-VIDEO device.

AUDIO OUT

Connect analog audio to various types of equipment.

DIGITAL AUDIO OUT

Connect digital audio to various types of equipment.
Note: In standby mode, these ports do not work.

ANTENNA/CABLE IN

Connect over-the air signals to this jack.
Connect cable signals to this jack.

Power Cord Socket

For operation with AC power.
Caution: Never attempt to operate the TV on DC power.

1

7

6

8

9

2

3

4

5

10

6

PREPARATION

ATTACHING THE TV TO A WALL

PREPARATION

10

We recommend that you set up the TV close to a wall so it cannot fall over if pushed backwards.
Additionally, we recommend that the TV be attached to a wall so it cannot be pulled in a forward direction,
potentially causing injury or damaging the product.
Caution: Please make sure that children don’t climb on or hang from the TV.

■

Insert the eye-bolts (or TV brackets and bolts) to tighten the product to the wall as shown in the picture.
*Insert the eye-bolts and tighten them securely in the upper holes.

Secure the wall brackets with the bolts (not provided as parts of the product, must purchase separately ) to
the wall. Match the height of the bracket that is mounted on the wall to the holes in the product.

Ensure the eye-bolts or brackets are tightened securely.

■

Use a sturdy rope (not provided as parts of the product, must purchase
separately) to tie the product. It is safer to tie the rope so it becomes horizontal
between the wall and the product.

■

Here shown may be somewhat different from your TV.

■

This feature is not available for all models.

PREPARATION

BACK COVER FOR WIRE ARRANGEMENT

11

■

Here shown may be somewhat different from your TV.

Connect the cables as necessary.
To connect an additional equipment, see the

EXTERNAL EQUIPMENT SETUP section.

Install the

CCAABBLLEE MMAANNAA GG EEMMEE NNTT

as shown.

(Insert it as pushing the loops on the both
sides of the cable management.)

Bundle the cables using the supplied twist
holder.

(This feature is not available for all models.)

Hold the

CC AA BBLLEE MMAANN AA GGEE MMEENNTT

with both

hands and pull it out.
(Pull it out as holding the loops on the both sides of

the cable management.)

NOTE

GG

Do not hold the CABLE MANAGEMENT when moving the product.

- If the product is dropped, you may be injured or the product may be broken.

How to remove the cable management

CABLE MANAGEMENT

TWIST HOLDER

1

2

3

PREPARATION

DESKTOP PEDESTAL INSTALLATION

PREPARATION

12

For proper ventilation, allow a clearance of 4inches on all four sides from the wall.

VESA WALL MOUNTING

This product accepts a VESA-compliant mounting interface pad. (optional)
There 4 threaded holes are available for attaching the bracket.

GG

Screw length needed depends on the wall mount used. For further information, refer to the VESA
Wall Mounting Instruction Guide.

NOTE

4 inches

4 inches

4 inches

4 inches

400mm

42/47 inches: 600mm
52 inches: 800mm

PREPARATION

ANTENNA OR CABLE CONNECTION

13

1. Antenna (Analog or Digital)

Wall Antenna Socket or Outdoor Antenna without a Cable Box
Connections.

For optimum picture quality, adjust antenna direction if needed.

2. Cable

Wall
Antenna
Socket

Outdoor
Antenna
(VHF, UHF)

Cable TV
Wall Jack

Multi-family Dwellings/Apartments
(Connect to wall antenna socket)

RF Coaxial Wire (75 ohm)

RF Coaxial Wire (75 ohm)

Single-family Dwellings /Houses
(Connect to wall jack for outdoor antenna)

Be careful not to bend the bronze wire
when connecting the antenna.

Copper Wire

ANTENNA/ANTENNA/
CABLE INCABLE IN

ANTENNA/ANTENNA/
CABLE INCABLE IN

GG

The TV will let you know when the analog, cable, and digital channel scans are complete.

NOTE

■

To improve the picture quality in a poor signal area, please purchase a signal amplifier and install properly.

■

If the antenna needs to be split for two TV’s, install a 2-Way Signal Splitter.

■

If the antenna is not installed properly, contact your dealer for assistance.

Antenna

UHF

Signal
Amplifier

VHF

ANTENNA/
CABLE IN

ANTENNA/
CABLE IN

EXTERNAL EQUIPMENT SETUP

14

HD RECEIVER SETUP

EXTERNAL EQUIPMENT SETUP

This TV can receive Digital Over-the-air/Cable signals without an external digital set-top box. However, if you
do receive digital signals from a digital set-top box or other digital external device, refer to the figure as
shown below.

This TV supports HDCP (High-bandwidth Digital Contents Protection)protocol for Digital Contents.

(RGB/DVI)

()

CONTRO

RS-23

(CONTROL

( )

S-VIDE

COMPONENT IN

1

2

VIDEO

AUDIO

Y L RPB PR

When connecting Component cable

1. How to connect

Connect the video outputs (Y, PB, PR

)

of the digital set

top box to the

CCOOMMPPOONNEENNTT IINN VVIIDDEEOO 11

jacks on
the set. Match the jack colors
(Y = green, P

B = blue, and PR = red).

Connect the audio output of the digital set-top box to
the

CCOOMMPPOONNEENNTT IINN AAUUDDIIOO 11

jacks on the set.

2. How to use

■

Turn on the digital set-top box.

(

Refer to the owner’s manual for the digital set-top box.

)

■

Select

CCoommppoonneenntt 11

input source with using the

IINNPPUUTT

button on the remote control.

■

If connected to

CCOOMMPPOONNEENNTT IINN 22

input, select

CCoommppoonneenntt 22

input source.

Signal

Component 1/2

Yes

Yes

Yes

Yes

Yes

HDMI/DVI1, 2 or 3

No

Yes

Yes

Yes

Yes

2

1

1

2

480i

480p

720p

10 8 0 i

10 8 0 p

Supported Display Specifications (Y, C

B /P

B,CR /PR

)

Horizontal Vertical

Frequency (KHz)Frequency (Hz

)

15.73 60.00

15.73 59.94

31.47 59.94

31.47 60.00

45.00 60.00

44.96 59.94

33.75 60.00

33.72 59.94

67.50 60.00

67. 432 59.939

27.00 24.00

26.97 23.94

33.75 30.00

33.71 29.97

Resolution

1280x720p

1920x1080i

1920x1080p

720x480i

720x480p

15

EXTERNAL EQUIPMENT SETUP

RGB IN

COMPONENT IN

AUDIO

(RGB/DV

RGB(PC)

1

2

VIDEO

( )

HDMI/DVI IN

1

2

3

HDMI-DTV OUTPUT

When connecting HDMI cable

Connect the digital set-top box to

HHDDMMII // DD VVII IINN11

,

22

or

33

jack on the set.

No separated audio connection is necessary.

1. How to connect

2. How to use

■

Turn on the digital set-top box.

(

Refer to the owner’s manual for the digital set-top box.

)

■

Select

HHDDMMII11,HHDDMMII22 orHHDDMMII33

input source with using

the

IINNPPUUTT

button on the remote control.

■

If the digital set-top box player does not support Auto HDMI,
you need to set the output resolution appropriately.

2

1

1

Supported Display Specifications (HDMI-DTV

)

Horizontal Vertical

Frequency (KHz)Frequency (Hz

)

31.47 60.00

31.47 59.94

45.00 60.00

44.96 59.94

33.75 60.00

33.72 59.94

67.50 60.00

67. 432 59.939

27.00 24.00

26.97 23.94

33.75 30.00

33.71 29.97

Resolution

720x480p

1280x720p

1920x1080i

1920x1080p

EXTERNAL EQUIPMENT SETUP

EXTERNAL EQUIPMENT SETUP

16

When connecting HDMI to DVI cable

( )

COMPONENT IN

AV IN 1

REMOTE

CONTROL IN

1

2

RS-232C IN

(CONTROL & SERVICE)

VIDEO

AUDIO

AUDIO OUT

OPTICAL COAXIAL

VIDEO

MONO

( )

AUDIO

S-VIDEO

HDMI/DVI IN

1

2

3

RGB IN

AUDIO

(RGB/DVI)

L R

DVI-DTV OUTPUT

RGB(PC)

DIGITAL AUDIO OUT

ANTENNA/

CABLE IN

Connect the DVI output of the digital set-top box to the

HHDDMMII // DD VVII IINN11, 22

or

33

jack on the set.

Connect the audio output of the digital set-top box to the

AAUUDDIIOO ((RRGGBB//DDVVII

))

jack on the set.

1. How to connect

■

Turn on the digital set-top box. (Refer to the owner’s manual for the digital set-top box.

)

■

Select

HHDDMMII11,HHDDMMII22 orHHDDMMII33

input source with using the

IINNPPUUTT

button on the remote control.

2. How to use

2

1

1

2

EXTERNAL EQUIPMENT SETUP

DVD SETUP

17

Component Input ports

To get better picture quality, connect a DVD player to the component input ports as shown below.

Component ports on the TV

YPB PR

Video output ports

on DVD player

Y

Y

Y

Y

P

B

Pb

B-Y

Cb

P

R

Pr

R-Y

Cr

AUDIO

(RGB/DVI)

RGB(PC)

REM

CONT

RS

(CONTR

( )

S-VI

COMPONENT IN

1

2

VIDEO

AUDIO

Y L RPB PR

When connecting Component cable

Connect the video outputs (Y, PB

, PR

)

of the DVD to

the

CCOOMMPPOONNEENNTT II NN VV IIDDEEOO11

jacks on the set.

Match the jack colors
(

Y = green, P

B = blue, and PR = red

)

.

Connect the audio outputs of the DVD to the
CCOOMMPPOONNEENNTT II NN AA UUDDIIOO 11

jacks on the set.

1. How to connect

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select

CCoommppoonneenntt 11

input source with using the

IINNPPUUTT

button on the remote control.

■

If connected to

CCOOMMPPOONNEENNTT IINN 22

input, select

CCoommppoonneenntt 22

input source.

■

Refer to the DVD player's manual for operating instruc­tions.

2

1

1

2

EXTERNAL EQUIPMENT SETUP

EXTERNAL EQUIPMENT SETUP

18

When connecting with an S-Video cable

RGB IN

COMPONENT

AUD

(RGB/

RGB(PC)

1

2

VIDEO

( )

HDMI/DVI IN

1

2

3

HDMI-DVD OUTPUT

( )

REMOTE

CONTROL IN

RS-232C IN

(CONTROL & SERVICE)

AUDIO OUT

OPTICAL COAXIAL

MONO

( )

AUDIO

S-VIDEO

AV IN 1

VIDEO

L R

S-VIDEO

AUDIO

DIGITAL AUDIO OUT

ANTENNA/

CABLE IN

Connect the S-VIDEO output of the DVD to the
SS--VVIIDDEEOO

input on the set.

Connect the audio outputs of the DVD to the

AAUUDDIIOO

input jacks on the set.

1. How to connect

2. How to use

■

Turn on the DVD player, insert a DVD.

■

Select

AA VV11

input source with using the

IINN PP UUTT

button on

the remote control.

■

If connected to

AAVV II NN 22

, select

AA VV22

input source.

■

Refer to the DVD player's manual for operating instructions.

When connecting HDMI cable

Connect the HDMI output of the DVD to the
HHDDMMII // DD VVII IINN11, 22 or33

jack on the set.

No separated audio connection is necessary.

1. How to connect

2. How to use

■

Select

HHDDMMII11,HHDDMMII22 orHHDDMMII33

input source with using

the

IINNPPUUTT

button on the remote control.

■

Refer to the DVD player's manual for operating instruc­tions.

■

If the DVD does not support Auto HDMI, you need to set
the output resolution appropriately.

2

1

2

1

EXTERNAL EQUIPMENT SETUP

1 2

1

EXTERNAL EQUIPMENT SETUP

VCR SETUP

19

When connecting with an antenna

■

To avoid picture noise (interference), leave an adequate distance between the VCR and TV.

■

If the 4:3 picture format is used; the fixed images on the sides of the screen may remain visible

on the screen.

L R

S-VIDEO VIDEO

OUTPUT
SWITCH

ANT IN

ANT OUT

RGB IN

COMPONENT IN

AV IN 1

AUDIO

(RGB/DVI)

REMOTE

CONTROL IN

RS-232C IN

(CONTROL & SERVICE)

VIDEO

AUDIO

AUDIO OUT

OPTICAL COAXIAL

VIDEO

MONO

( )

AUDIO

S-VIDEO

( )

DIGITAL AUDIO OUT

ANTENNA/

CABLE IN

Wall Jack

Antenna

Connect the RF antenna out socket of the VCR to the

AAnntteennnnaa

socket on the set.

Connect the antenna cable to the RF antenna in socket of the VCR.

1. How to connect

■

Set VCR output switch to 3 or 4 and then tune TV to the same channel number.

■

Insert a video tape into the VCR and press PLAY on the VCR. (Refer to the VCR owner’s manual.

)

2. How to use

2

1

1

2

EXTERNAL EQUIPMENT SETUP

EXTERNAL EQUIPMENT SETUP

20

In the event that you connect
both Video and the S-Video
cables, only the S-Video will work.

CAUTION

GB/DVI)

REMOTE

CONTROL IN

RS-232C IN

(CONTROL & SERVICE)

AUDIO

AUDIO OUT

OPTICAL COAXIAL

AV IN 1

VIDEO

MONO

( )

AUDIO

S-VIDEO

DIGITAL AUDIO OUT

ANTENNA/

CABLE IN

L R

S-VIDEO VIDEO

OUTPUT

SWITCH

ANT IN

ANT OUT

( )

(

)

AUDIO

(RGB/DVI)

REMOTE

CONTROL IN

RS-232C IN

(CONTROL & SERVICE)

AUDIO

AUDIO OUT

OPTICAL COAXIAL

AV IN 1

VIDEO

MONO

( )

AUDIO

S-VIDEO

DIGITAL AUDIO OUT

ANTENNA/

CABLE IN

L R

S-VIDEO VIDEO

OUTPUT
SWITCH

ANT IN

ANT OUT

Connect the

AAUUDDIIOO/VVIIDDEEOO

jacks between TV and VCR.
Match the jack colors (Video = yellow, Audio Left = white,
and Audio Right = red)

1. How to connect

2. How to use

■

Insert a video tape into the VCR and press PLAY on the
VCR. (Refer to the VCR owner’s manual.

)

■

Select

AA VV11

input source with using the

IINN PP UUTT

button on

the remote control.

■

If connected to

AAVV II NN 22

, select

AA VV22

input source.

If you have a mono VCR, connect the audio cable from
the VCR to the

AAUU DD IIOO LL//MMOO NNOO

jack of the set.

NOTE

When connecting with an S-Video cable

When connecting with a RCA cable

Connect the S-VIDEO output of the VCR to the

SS --

VV IIDD EE OO

input on the set. The picture quality is

improved; compared to normal composite (RCA cable

)

input.

Connect the audio outputs of the VCR to the

AAUUDDIIOO

input jacks on the set.

1. How to connect

2. How to use

■

Insert a video tape into the VCR and press PLAY on the VCR.
(

Refer to the VCR owner’s manual.

)

■

Select

AAVV11

input source with using the

IINNPPUUTT

button on the

remote control.

■

If connected to

AAVV IINN 22

, select

AAVV22

input source.

1

2

1

1

1

2

EXTERNAL EQUIPMENT SETUP

PC SETUP

21

This TV provides Plug and Play capability, meaning that the PC adjusts automatically to the TV's settings.

GG

Check the image on your TV. There may be noise associated
with the resolution, vertical pattern, contrast or brightness in
PC mode. If noise is present, change the PC output to another
resolution, change the refresh rate to another rate or adjust
the brightness and contrast on the VIDEO menu until the
picture is clear. If the refresh rate of the PC graphic card can
not be changed, change the PC graphic card or consult the
manufacturer of the PC graphic card.

NOTE

DVI IN

COMPONENT IN

R

CO

1

2

R

(CON

VIDEO

AUDIO

( )

S-

RGB IN

AUDIO

(RGB/DVI)

RGB(PC)

RGB OUTPUT AUDIO

A

C

When connecting D-sub 15 pin cable

Connect the RGB output of the PC to the

RRGGBB

((

PPCC

))

jack on the set.

Connect the PC audio output to the

AAUUDDIIOO

((

RRGGBB//DDVVII

))

jack on the set.

1. How to connect

2. How to use

■

Turn on the PC and the set.

■

Select

RRGGBB--PPCC

input source with using the

IINNPPUUTT

button

on the remote control.

2

1

1 2

22

EXTERNAL EQUIPMENT SETUP

EXTERNAL EQUIPMENT SETUP

GG

If the PC has a DVI output and no HDMI output, a separated audio connection is necessary.

GG

If the PC does not support Auto DVI, you need to set the output resolution appropriately. To get the

best picture quality, adjust the output resolution of PC graphics card's output resolution to 1920x1080,
60Hz.

NOTE

( )

COMPONENT IN

AV IN 1

REMOTE

CONTROL IN

1

2

RS-232C IN

(CONTROL & SERVICE)

VIDEO

AUDIO

AUDIO OUT

OPTICAL COAXIAL

VIDEO

MONO

( )

AUDIO

S-VIDEO

HDMI/DVI IN

1

2

3

RGB IN

AUDIO

(RGB/DVI)

L R

DVI-PC OUTPUT

RGB(PC)

DIGITAL AUDIO OUT

ANTENNA/

CABLE IN

Connect the DVI output of the PC to the

HHDDMMII//DDVVII IINN11, 22

or

33

jack on the set.

(Use the HDMI to DVI cable)

Connect the PC audio output to the

AAUUDDIIOO ((RRGGBB//DDVVII

))

jack on the set.

1. How to connect

■

Turn on the PC and the set

■

Select

HHDDMMII11,HHDDMMII22 orHHDDMMII33

input source with using the

IINNPPUUTT

button on the remote control.

2. How to use

2

1

1

2

When connecting HDMI to DVI cable

EXTERNAL EQUIPMENT SETUP

23

GG

Depending on the graphics card, DOS mode may

not work if a HDMI to DVI Cable is in use.

GG

Check the image on your TV. There may be noise

associated with the resolution, vertical pattern,
contrast or brightness in PC mode. If noise is pre­sent, change the PC output to another resolution,
change the refresh rate to another rate or adjust
the brightness and contrast on the PICTURE menu
until the picture is clear. If the refresh rate of the

PC graphic card can not be changed, change the
PC graphic card or consult the manufacturer of the
PC graphic card.

GG

Avoid keeping a fixed image on the screen for a

long period of time. The fixed image may become
permanently imprinted on the screen.

GG

The synchronization input form for Horizontal and

Vertical frequencies is separate.

NOTES

Supported Display Specifications (RGB/HDMI-PC

)

Horizontal Vertical

Frequency(KHz)Frequency(Hz

)

31.468 70.09

31.469 70.08

31.469 59.94

37.861 72.80

37. 500 75.00

35.156 56.25

37.879 60.31

48.077 72.18
46 .875 75 .0 0

48.363 60.00

56.476 70.06

60.023 75.02

47. 776 59. 870

60.289 74.893

47.712 60.015

63.981 60.020

79.976 75.025

75.00 60.00

67.50 60.00

Resolution

720x400

1360x768

640x350

* RGB-PC mode only: 1280x768 (H-60.289, V-74.893)

640x480

800x600

1024x768

1280x1024

1600x1200

1920x1080

1280x768

EXTERNAL EQUIPMENT SETUP

EXTERNAL EQUIPMENT SETUP

24

Screen Setup for PC mode

Overview

When the RGB input of the set is connected to a PC Output,
Select RGB-PC with using the

IINN PPUU TT

button on the remote

control.

When you change the resolution, select the proper resolution
in present input to see the best picture appearance.

Picture Mode

Color Temperature

XD

Advanced

Aspect Ratio

Picture Reset

Screen

G

TruM Demo

Selection ( Gor ) leads you to
thescreen adjustment menu.

Picture Mode : User1

Color Temperature : Cool

XD

Advanced

Aspect Ratio : 16:9

Picture Reset

Screen

TruM Demo

Press the

MMEENNUU

button and then useDDor EEbutton

to select the

PPIICCTTUURREE

menu.

Press the

GG

button and then useDDor EEbutton to

select

SSccrreeeenn

.

Press the

GG

button to enter the screen adjustment

menu.

2

3

1

25

EXTERNAL EQUIPMENT SETUP

Resolution

Position

GG

Size

Phase

Reset

Move Prev

Resolution

Position

Size

Phase

Reset

GG

Initialize Settings.

Yes

No

Prev

Select

OK

RReessoolluuttiioonn

XGA (1024, 1280, 1360) isn’t

distinguished because of having

the same H/V Sync Time.
This function is you to select the
Default Sync Time.

PPoossiittiioonn

This function is to adjust picture
to left/right and up/down as you
prefer.

SSiizzee

This function is to minimize any
vertical bars or stripes visible on
the screen background. And the
horizontal screen size will also
change.

PPhhaassee

This function allows you to
remove any horizontal noise and
clear or sharpen the image of char­acters.

Use DDor EEbutton to select

RReessoolluuttiioonn, PPoossiittiioonn, SSiizzee

, or

PPhhaassee

.

Press the

EENNTTEERR

button and then use

DD EE

FF GG

button to

make appropriate adjustments.

■

The

PPhhaassee

adjustment range is

--1166~++1166

.

■

The

SSiizzee

adjustment range is

--3300~++3300

.

Press the

EENNTTEERR

button.

Adjustment for screen Resolution, Position, Size, Phase, Reset

Use DDor EEbutton to select

RReesseett

.

Press the

EENNTTEERR

button and then use

FF

or GGbutton to

select

YYeess

.

Press the

EENNTTEERR

button.

Initializing (Reset to original factory values

)

2

3

1

2

3

1

To initialize the adjusted values.

EXTERNAL EQUIPMENT SETUP

OTHER A/V SOURCE SETUP

EXTERNAL EQUIPMENT SETUP

26

Camcorder

Video Game Set

Connect the

AAUUDDIIOO/VVIIDDEEOO

jacks
between TV and external equipment.
Match the jack colors

.

(

Video = yellow, Audio Left = white, and

Audio Right = red

)

1. How to connect

2. How to use

■

Select

AAVV22

input source with using the

IINNPPUUTT

button on the remote control.

■

If connected to

AAVV IINN 11

input, select

AAVV11

input source.

■

Operate the corresponding external equipment.

1

S-VIDEO

L R

VIDEO

1

The TV has a special signal output capability which allows you to hook up the second TV or monitor.

AV IN 2V IN 2

L/L/MONOMONO

R

AUDIOAUDIO

VIDEOVIDEO

S-VIDEO

USB INUSB IN

Connect the USB device to the

UUSS BB II NN

jacks on the

side of TV.

1. How to connect

1

2. How to use

■

After connecting the

UUSS BB II NN

jacks, you use the

function. (

GG

pp..3399

)

MEDIAMEDIA

HOST HOST

1

or

USB IN SETUP

EXTERNAL EQUIPMENT SETUP

AUDIO OUT SETUP

27

Send the TV’s audio to external audio equipment via the Audio Output port.

GG

When connecting with external audio equipment, such as

amplifers or speakers, please turn the TV speakers off.
(

GG

pp..6622

)

NOTE

GG

Do not look into the optical output port. Looking at the

laser beam may damage your vision.

GG

Block the SPDIF out(optical/coaxial) about the contents

with ACP(Audio Copy Protection) function.

CAUTION

( )

AV IN 1

REMOTE

CONTROL IN

RS-232C IN

(CONTROL & SERVICE)

AUDIO OUT

VIDEO

MONO

( )

AUDIO

S-VIDEO

DIGITAL AUDIO OUT

OPTICAL

COAXIAL

ANTENNA/

CABLE IN

Connect one end of the optical or coaxial cable to the
TV’s

OOPP TTII CCAA LL

or

CCOOAAXXIIAALL

port of

DDIIGGIITTAALL AAUUDDIIOO

OOUUTT

.

Connect the other end of the optical or coaxial cable
to the digital audio input on the audio equipment.

Set the “TV Speaker option - Off ” in the AUDIO menu.
(

GG

pp..6622

). See the external audio equipment instruction

manual for operation.

1. How to connect

2

3

1

1

2

REMOTE

CONTROL IN

RS-232C IN

(CONTROL & SERVICE)

OPTICAL COAXIAL

AUDIO OUT

DIGITAL AUDIO OUT

ANTENNA/

CABLE IN

L R

AUDIO

Analog

Digital

Connect audio outputs to the TV’s

AAUUDDIIOO OOUUTT

jacks.

Set the “TV Speaker option - Off ” in the AUDIO menu.
(

GG

pp..6622

). See the external audio equipment instruction

manual for operation.

2

1

1

WATCHING TV / CHANNEL CONTROL

REMOTE CONTROL FUNCTIONS

WATCHING TV /CHANNEL CONTROL

28

APM

CC

AUTO DEMO

M/C EJECT

TV INPUTTV INPUT

STBSTB

MENU

BRIGHT +

BRIGHT -

TIMER

RATIO

SIMPLINK

BACKBACK

TV INPUT

STB

BACK

TV INPUT

STB

BACK

PICTURE

SOUND

SAP

CC

MARK

USB EJECT

MEDIA HOSTMEDIA HOST

MEDIA HOST

MEDIA HOST

BRIGHT +/-

THUMBSTICK

(Up/Down/Left

Right/ENTER)

EXIT

TIMER

RATIO

SIMPLINK

VOLUME UP

/DOWN

MUTE

FAV

CHANNEL

UP/DOWN

BACK

— (DASH)

■

Controls the mode.

■

Control video cassette recorders or DVD players.

Displays the main menu.

■

Adjust brightness on screen.

■

It turns to the default settings brightness by changing

mode source.

■

Navigate the on-screen menus and adjust the system

settings to your preference.

Clear all on-screen displays and return to TV viewing from
any menu.

Select the amount of time before your TV turns off auto­matically.

GG

pp..7722

Change the aspect ratio.

GG

pp..4466

See a list of AV devices connected to TV.

When you toggle this button, the SimpLink menu appears
at the screen.

Increase/decrease the sound level.

Switch the sound on or off.

pp..3300

Scroll through the programmed Favorite channels.

pp..3344

Select available channels.

Tune to the last channel viewed.

Used to enter a program number for multiple
program channels such as 2-1, 2-2, etc.

MEDIAMEDIA

HOST HOST

mode control

buttons

MEDIAMEDIAMEDIA

HOST HOST HOST

MEDIA

HOST

NUMBER button

VCR/DVD

buttons

MENU

When using the remote control, aim it at the remote control sensor on the TV.