Please read this manual carefully before operating
your set and retain it for future reference.
42PN4500
50PN4500
P/NO : MFL67701702 (1308-REV05)
60PN500050PN5300
60PN5300
50PN6500
60PN6500
60PN6550
www.lg.com
IMPORTANT SAFETY INSTRUCTIONS
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
Short-circuit
Breaker
Power Supply
Short-circuit
Breaker
Power Supply
Short-circuit
Breaker
Power Supply
2
IMPORTANT SAFETY INSTRUCTIONS
Always comply with the following precautions to avoid dangerous situations and ensure peak performance of your
product.
Read these instructions.
Keep these instructions.
WARNING/CAUTION
RISK OF ELECTRIC SHOCK
DO NOT OPEN
TO REDUCE THE RISK OF ELECTRIC SHOCK
DO NOT REMOVE COVER (OR BACK). NO
USER SERVICEABLE PARTS INSIDE. REFER TO
QUALIFIED SERVICE PERSONNEL.
The lightning flash with arrowhead symbol,
within an equilateral triangle, is intended to
alert the user to the presence of
uninsulated “dangerous voltage” within the
product’s enclosure that may be of sufficient
magnitude to constitute a risk of electric shock to
persons.
Heed all warnings.
Follow all instructions.
Do not use this apparatus near water.
y
Clean only with a dry cloth.
y
Do not block any ventilation openings. Install in
y
accordance with the manufacturer’s instructions.
ENGLISH
The exclamation point within an equilateral
triangle is intended to alert the user to the
presence of important operating and
maintenance (servicing) instructions in the
literature accompanying the appliance.
WARNING/CAUTION
- TO REDUCE THE RISK OF FIRE AND ELECTRIC
SHOCK, DO NOT EXPOSE THIS PRODUCT TO
RAIN OR MOISTURE.
WARNING
If you ignore the warning message, you may be
seriously injured or there is a possibility of accident
or death.
CAUTION
If you ignore the caution message, you may be
slightly injured or the product may be damaged.
NOTE
The note helps you understand and use the product
safely. Please read the note carefully before using
the product.
Do not install near any heat sources such as
y
radiators, heat registers, stoves, or other apparatus
(including amplifiers) that produce heat.
Do not defeat the safety purpose of the polarized
y
or grounding-type plug. A polarized plug has two
blades with one wider than the other. A grounding
type plug has two blades and a third grounding
prong. The wide blade or the third prong are
provided for your safety. If the provided plug does
not fit into your outlet, consult an electrician for
replacement of the obsolete outlet (Can differ by
country).
Do not press strongly upon the panel with a hand or
y
a sharp object such as a nail, pencil or pen, or make
a scratch on it.
WARNING
to the State of California to cause cancer and birth
defects or other reproductive harm.
Wash hands after handling.
: This product contains chemicals known
IMPORTANT SAFETY INSTRUCTIONS
Short-circuit
Breaker
Power Supply
Short-circuit
Breaker
Power Supply
3
Protect the power cord from being walked on
y
or pinched particularly at plugs, convenience
receptacles, and the point where they exit from the
apparatus.
Only use attachments/accessories specified by the
y
manufacturer.
Use only with a cart, stand, tripod, bracket, or table
y
specified by the manufacturer, or sold with the
apparatus. When a cart is used, use caution when
moving the cart/apparatus combination to avoid
injury from tip-over.
Unplug this apparatus during lightning storms or
y
when unused for long periods of time.
CAUTION concerning the Power Cord
y
(Can differ by country):
It is recommended that appliances be placed upon a
dedicated circuit; that is, a single outlet circuit which
powers only that appliance and has no additional
outlets or branch circuits. Check the specification
page of this owner’s manual to be certain. Do
not connect too many appliances to the same AC
power outlet as this could result in fire or electric
shock. Do not overload wall outlets. Overloaded
wall outlets, loose or damaged wall outlets,
extension cords, frayed power cords, or damaged or
cracked wire insulation are dangerous. Any of these
conditions could result in electric shock or fire.
Periodically examine the cord of your appliance, and
if its appearance indicates damage or deterioration,
unplug it, discontinue use of the appliance, and have
the cord replaced with an exact replacement part
by an authorized service. Protect the power cord
from physical or mechanical abuse, such as being
twisted, kinked, pinched, closed in a door, or walked
upon. Pay particular attention to plugs, wall outlets,
and the point where the cord exits the appliance. Do
not move the TV with the power cord plugged in.
Do not use a damaged or loose power cord. Be sure
do grasp the plug when unplugging the power cord.
Do not pull on the power cord to unplug the TV.
ENGLISH
Refer all servicing to qualified service personnel.
y
Servicing is required when the apparatus has been
damaged in any way, such as power-supply cord or
plug is damaged, liquid has been spilled or objects
have fallen into the apparatus, the apparatus has
been exposed to rain or moisture, does not operate
normally, or has been dropped.
Do not stick metal objects or any other conductive
y
material into the power cord. Do not touch the end
of the power cord while it is plugged in.
Keep the packing anti-moisture material or vinyl
y
packing out of the reach of children. Anti-moisture
material is harmful if swallowed. If swallowed
by mistake, force the patient to vomit and visit
the nearest hospital. Additionally, vinyl packing
can cause suffocation. Keep it out of the reach of
children.
Warning
y
- To reduce the risk of fire or electrical
shock, do not expose this product to rain, moisture
or other liquids. Do not touch the TV with wet
hands. Do not install this product near flammable
objects such as gasoline or candles, or expose the
TV to direct air conditioning.
Do not expose to dripping or splashing and do not
y
place objects filled with liquids, such as vases, cups,
etc. on or over the apparatus (e.g. on shelves above
the unit).
IMPORTANT SAFETY INSTRUCTIONS
4
ENGLISH
Grounding
y
(Except for devices which are not grounded.)
Ensure that you connect the earth ground wire to
prevent possible electric shock (i.e. a TV with a
three-prong grounded AC plug must be connected
to a three-prong grounded AC outlet). If grounding
methods are not possible, have a qualified
electrician install a separate circuit breaker. Do not
try to ground the unit by connecting it to telephone
wires, lightening rods, or gas pipes.
Short-circuit
Breaker
As long as this unit is connected to the AC wall
y
Power Supply
outlet, it is not disconnected from the AC power
source even if the unit is turned off.
Do not attempt to modify this product in any way
y
without written authorization from LG Electronics.
Unauthorized modification could void the user’s
authority to operate this product.
Outdoor Antenna Grounding
y
(Can differ by country):
If an outdoor antenna is installed, follow the
precautions below. An outdoor antenna system
should not be located in the vicinity of overhead
power lines or other electric light or power circuits,
or where it can come in contact with such power
lines or circuits as death or serious injury can occur.
Be sure the antenna system is grounded so as to
provide some protection against voltage surges
and built-up static charges. Section 810 of the
National Electrical Code (NEC) in the U.S.A. provides
information with respect to proper grounding of the
mast and supporting structure, grounding of the
lead-in wire to an antenna discharge unit, size of
grounding conductors, location of antenna discharge
unit, connection to grounding electrodes and
requirements for the grounding electrode.
Antenna grounding according to the National
Electrical Code, ANSI/NFPA 70
Cleaning
y
When cleaning, unplug the power cord and wipe
gently with a soft cloth to prevent scratching. Do
not spray water or other liquids directly on the TV
as electric shock may occur. Do not clean with
chemicals such as alcohol, thinners or benzine.
Moving
y
Make sure the product is turned off, unplugged
and all cables have been removed. It may take 2 or
more people to carry larger TVs. Do not press or put
stress on the front panel of the TV.
Ventilation
y
Install your TV where there is proper ventilation. Do
not install in a confined space such as a bookcase.
Do not cover the product with cloth or other
materials while plugged. Do not install in excessively
dusty places.
If you smell smoke or other odors coming from
y
the TV, unplug the power cord and contact an
authorized service center.
Keep the product away from direct sunlight.
y
Never touch this apparatus or antenna during a
y
thunder or lightning storm.
When mounting a TV on the wall, make sure not
y
to install the TV by hanging the power and signal
cables on the back of the TV.
Do not allow an impact shock or any objects to fall
y
into the product, and do not drop anything onto the
screen.
Disconnecting the Main Power
y
The power outlet used with this device must remain
easily accessible.
Store the accessories (battery, etc.) in a safe
y
location out of the reach of children.
This apparatus use batteries. In your community
y
there might be regulations that require you
to dispose of these batteries properly due to
environmental considerations. Please contact your
local authorities for disposal or recycling information.
Do not dispose of batteries in a fire.
y
Do not short circuit, disassemble or allow the
y
batteries to overheat.
Ground Clamp
Electric Service
Equipment
Ground Clamp
NEC: National Electrical Code
Antenna Lead in Wire
Antenna Discharge Unit
(NEC Section 810-20)
Grounding Conductor
(NEC Section 810-21)
Power Service Grounding
Electrode System
(NEC Art 250, Part H)
Dot Defect
y
The Plasma or LCD panel is a high technology
product with resolution of two million to six million
pixels. In a very few cases, you could see fine dots
on the screen while you’re viewing the TV. Those
dots are deactivated pixels and do not affect the
performance and reliability of the TV.
Generated Sound
y
“Cracking” noise: A cracking noise that occurs
when watching or turning off the TV is generated by
plastic thermal contraction due to temperature and
humidity. This noise is common for products where
thermal deformation is required.
Electrical circuit humming/panel buzzing: A low level
noise is generated from a high-speed switching
circuit, which supplies a large amount of current
to operate a product. It varies depending on the
product.
This generated sound does not affect the
performance and reliability of the product.
Take care not to touch the ventilation openings.
y
When watching the TV for a long period, the
ventilation openings may become hot. This does
not affect the performance of the product or cause
defects in the product.
Preventing “Image burn” or “Burn-in” on your TV
screen
If a fixed image displays on the TV screen for a long
y
period of time, it will be imprinted and become a
permanent disfigurement on the screen. This is
“image burn” or “burn-in” and not covered by the
warranty.
If the aspect ratio of the TV is set to 4:3 for a
y
long period of time, image burn may occur on the
letterboxed area of the screen.
Avoid displaying a fixed image on the TV screen for
y
a long period of time (2 or more hours for LCD, 1
or more hours for the Plasma TV) to prevent image
burn.
IMPORTANT SAFETY INSTRUCTIONS
For USA and Canada
FCC NOTICE
This equipment has been tested and found to
comply with the limits for a Class B digital device,
pursuant to Part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against
harmful interference in a residential installation. This
equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful
interference to radio communications. However, there
is no guarantee that interference will not occur in a
particular installation. If this equipment does cause
harmful interference to radio or television reception,
which can be determined by turning the equipment
off and on, the user is encouraged to try to correct
the interference by one or more of the following
measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment
and the receiver.
- Connect the equipment to an outlet on a circuit
different from that to which the receiver is
connected.
- Consult the dealer or an experienced radio/TV
technician for help.
This device complies with part 15 of the FCC Rules.
Operation is subject to the following two conditions:
(1) this device may not cause harmful interference and
(2) this device must accept any interference received,
including interference that may cause undesired
operation of the device.
Any changes or modifications in construction of this
device which are not expressly approved by the party
responsible for compliance could void the user’s
authority to operate the equipment.
NOTE TO CABLE/TV INSTALLER
This reminder is provided to call the CATV system
installer’s attention to Article 820-40 of the National
Electric Code (U.S.A.). The code provides guidelines
for proper grounding and, in particular, specifies that
the cable ground shall be connected to the grounding
system of the building, as close to the point of the
cable entry as practical.
5
ENGLISH
LICENSES
6
LICENSES
Supported licenses may differ by model. For more information about licenses, visit 'www.lg.com'.
Manufactured under license from Dolby Laboratories. “Dolby” and the double-D symbol are
trademarks of Dolby Laboratories.
The terms HDMI and HDMI High-Definition Multimedia Interface, and the HDMI logo are
trademarks or registered trademarks of HDMI Licensing LLC in the United States and other
countries.
ENGLISH
TABLE OF CONTENTS
TABLE OF CONTENTS
7
2 IMPORTANT SAFETY INSTRUCTIONS
6 LICENSES
7 TABLE OF CONTENTS
8 INSTALLATION PROCEDURE
8 ASSEMBLING AND PREPARING
8 Unpacking
10 Parts and buttons
11 Additional information of the manual
11 Lifting and moving the TV
12 Setting up the TV
12 - Attaching the stand
14 - Mounting on a table
15 - Mounting on a wall
16 - Tidying cables
17 MAKING CONNECTIONS
17 Connecting to an antenna or cable
18 Connecting to a HD receiver, DVD Player or VCR
18 - HDMI Connection
19 - DVI to HDMI Connection
20 - Component Connection
21 - Composite Connection
22 Connecting to a PC
22 - HDMI Connection or DVI to HDMI Connection
24 Connecting to an Audio System
24 - Digital Optical Audio Connection
24 Connecting a USB Device
25 REMOTE CONTROL
27 WATCHING TV
27 Turning the TV on for the first time
28 TROUBLESHOOTING
29 EXTERNAL CONTROL DEVICE SETUP
30 SPECIFICATIONS
ENGLISH
NOTE
Image shown may differ from your TV.
y
Your TV’s OSD (On Screen Display) may differ
y
slightly from that shown in this manual.
The available menus and options may differ from
y
the input source or product model that you are
using.
New features may be added to this TV in the
y
future.
INSTALLATION PROCEDURE / ASSEMBLING AND PREPARING
8
INSTALLATION PROCEDURE
Open the package and make sure all the accessories are included.
1
Attach the stand to the TV set.
2
Connect an external device to the TV set.
3
ASSEMBLING AND PREPARING
Unpacking
Check your product box for the following items. If there are any missing accessories, contact the local dealer where you
purchased your product. The illustrations in this manual may differ from the actual product and item.
ENGLISH
Remote control,
Batteries (AAA)
(See p.25)
(For 42PN4500)(For 50PN4500, 60PN5000,
Stand Screws
7 EA, M4 x 14
(See p.12)
(For 50PN4500, 50PN5300,
50PN6500)
Protection Cover
(See p.13)
Owner’s manual,
CD manual
50/60PN5300,50/60PN6500,
60PN6550)
Stand Screws
7 EA, M5 x 16
(See p.12)
Power Cord holder
(Depending on model)
(See p.16)
Power Cord
(For 42PN4500)
Desk-mount Screw
(See p.14)
Stand Body, Stand Base
(See p.12)
Ferrite core
(Depending on model)
(See p.9)
ASSEMBLING AND PREPARING
CAUTION
Do not use any unapproved items to ensure the safety and product life span.
y
Any damages or injuries by using unapproved items are not covered by the warranty.
y
Some models appear to have a thin film on the screen. It is actually part of the screen, do not remove it.
y
NOTE
The items supplied with your product may vary depending on the model.
y
Product specifications or contents of this manual may be changed without prior notice due to upgrade of product
y
functions.
For an optimal connection, HDMI cables and USB devices should have bezels less than 10 mm (0.39 inches)
y
thick and 18 mm (0.7 inches) width. Use an extension cable that supports USB 2.0 if the USB cable or USB
memory stick does not fit into your TV's USB port.
9
B
A
B
A
*A 10 mm (0.39 inches)
*B 18 mm (0.7 inches)
How to use the ferrite core
y
- If there are two ferrite cores, follow as shown in Figures 1-1 & 2-1 (or 2-2).
- If there are three ferrite cores, follow as shown in Figures 1-2 & 2-1 (or 2-2).
1 Use the ferrite core to reduce the electromagnetic interference in the power cable.
Wind the power cable on the ferrite core once. Place the ferrite core close to the TV and a wall
plug.
[to a wall plug]
[to the TV]
[Figure 1-1]
[to a wall plug]
[to the TV]
[Figure 1-2]
2 Use the ferrite core to reduce the electromagnetic interference in the cable.
Place the ferrite core close to the TV.
ENGLISH
(Black)
[Cross Section of
Ferrite Core]
Wind the component cable on the ferrite core once.
[to an External device]
[Figure 2-1]
Wind the PC audio cable on the ferrite core once.
[to an External device]
[Figure 2-2]
10 mm(+ / - 5 mm)
10 mm(+ / - 5 mm)
[to the TV]
[to the TV]
(Black)
[Cross Section of
Ferrite Core]
ASSEMBLING AND PREPARING
10
Parts and buttons
Remote control sensor
ENGLISH
Buttons
Power indicator
Screen
Speakers
ButtonDescription
/ Scrolls through the saved channels.
/
Adjusts the volume level.
Selects the highlighted menu option or confirms an input.
Accesses the main menus, or saves your input and exits the menus.
Changes the input source.
Turns the power on or off.
ASSEMBLING AND PREPARING
11
Additional information of the
manual
Viewing the owner's manual
The owner’s manual in PDF file format is supplied on the
enclosed CD. Install the Adobe Acrobat Reader to view
the owner’s manual on your PC.
Insert the supplied CD.
1
The web page appears automatically.
Click Owner’s Manual on the web page.
2
View the owner’s manual.
3
NOTE
If the web page does not appear automatically,
y
access My computer and then click LG and
to view the owner’s manual.
html
index.
Lifting and moving the TV
When moving or lifting the TV, read the following to
prevent the TV from being scratched or damaged and for
safe transportation regardless of its type and size.
CAUTION
Avoid touching the screen at all times, as this
y
may result in damage to the screen.
It is recommended to move the TV in the box or
y
packing material that the TV originally came in.
Before moving or lifting the TV, disconnect the
y
power cord and all cables.
When holding the TV, the screen should face
y
away from you to avoid damage.
Hold the top and bottom of the TV frame firmly.
y
Make sure not to hold the transparent part,
speaker, or speaker grill area.
ENGLISH
When transporting a large TV, there should be at
y
least 2 people.
When transporting the TV by hand, hold the TV as
y
shown in the following illustration.
When transporting the TV, do not expose the TV
y
to jolts or excessive vibration.
When transporting the TV, keep the TV upright,
y
never turn the TV on its side or tilt towards the left
or right.
ASSEMBLING AND PREPARING
12
Setting up the TV
You can mount your TV to a wall or attach the stand if you wish to place the TV on an entertainment center or other
furniture.
Attaching the stand
If you are not mounting the TV to a wall, use the following instructions to attach the stand.
CAUTION
When attaching the stand to the TV set, place the screen facing down on a cushioned table or flat surface to
y
protect the screen from scratches.
Make sure that the screws are fastened completely. (If they are not fastened securely enough, the TV may tilt
y
forward after being installed.)
Do not fasten the screws with too much force; otherwise they may be worn out and get loosened.
y
ENGLISH
1
Stand Body
2
Stand Base
Front
For 42PN4500
3 EA
M4 x 14
For 50PN4500, 60PN5000,
50/60PN5300, 50/60PN6500,
60PN6550
3 EA
M5 x 16
For 42PN4500
3
For 50PN4500, 60PN5000,
50/60PN5300, 50/60PN6500,
60PN6550
4 EA
M4 x 14
4 EA
M5 x 16
To detach the stand,
For 50PN4500, 50PN5300, 50PN6500
1
ASSEMBLING AND PREPARING
4 EA
M5 x 16
13
1 EA
2
M5 x 16
ENGLISH
2
Protection cover
1
NOTE
Remove the stand before installing the TV on a
y
wall mount by performing the stand attachment
in reverse.
When installing the wall mounting bracket,
y
use the Protection cover. This will protect the
opening from accumulating dust and dirt.
ASSEMBLING AND PREPARING
14
Mounting on a table
1
2
ENGLISH
Lift and tilt the TV into its upright position on a table.
- Leave a 10 cm (4 inches) (minimum) space from
the wall for proper ventilation.
10 cm
(4 inches)
10 cm
Connect the power cord to a wall outlet.
10 cm
10 cm
CAUTION
Do not place the TV near or on sources
y
of heat, as this may result in fire or other
damage.
Securing the TV to a table
(For 42PN4500)
Fix the TV to a table to prevent from tilting forward,
damage, and potential injury.
Mount the TV on a table, and then insert and tighten the
supplied screw on the rear of the stand.
WARNING
To prevent TV from falling over, the TV should be
y
securely attached to the floor/wall per installation
instructions. Tipping, shaking, or rocking the TV
may cause injury.
Adjusting the angle of the TV to suit view
Swivel 20 degrees to the left or right and adjust the
angle of the TV to suit your view.
20˚20˚
CAUTION
When adjusting the angle of the TV, watch out for
y
your fingers.
- Personal injury may occur if hands or fingers are
pinched. If the product is tilted too much, it may
fall, causing damage or injury.
Loading...
+ 30 hidden pages
You need points to download manuals.
1 point = 1 manual.
You can buy points or you can get point for every manual you upload.